1 files changed, 0 insertions, 100 deletions

diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
deleted file mode 100644
index 6a293b7fff3..00000000000
--- a/include/linux/platform_data/atmel.h
+++ /dev/null
@@ -1,100 +0,0 @@
-/*
- * atmel platform data
- *
- * GPL v2 Only
- */
-
-#ifndef __ATMEL_H__
-#define __ATMEL_H__
-
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/device.h>
-#include <linux/i2c.h>
-#include <linux/leds.h>
-#include <linux/spi/spi.h>
-#include <linux/usb/atmel_usba_udc.h>
-#include <linux/atmel-mci.h>
-#include <sound/atmel-ac97c.h>
-#include <linux/serial.h>
-#include <linux/platform_data/macb.h>
-
-/*
- * at91: 6 USARTs and one DBGU port (SAM9260)
- * avr32: 4
- */
-#define ATMEL_MAX_UART  7
-
- /* USB Device */
-struct at91_udc_data {
-        int     vbus_pin;               /* high == host powering us */
-        u8      vbus_active_low;        /* vbus polarity */
-        u8      vbus_polled;            /* Use polling, not interrupt */
-        int     pullup_pin;             /* active == D+ pulled up */
-        u8      pullup_active_low;      /* true == pullup_pin is active low */
-};
-
- /* Compact Flash */
-struct at91_cf_data {
-        int     irq_pin;                /* I/O IRQ */
-        int     det_pin;                /* Card detect */
-        int     vcc_pin;                /* power switching */
-        int     rst_pin;                /* card reset */
-        u8      chipselect;             /* EBI Chip Select number */
-        u8      flags;
-#define AT91_CF_TRUE_IDE        0x01
-#define AT91_IDE_SWAP_A0_A2     0x02
-};
-
- /* USB Host */
-#define AT91_MAX_USBH_PORTS     3
-struct at91_usbh_data {
-        int             vbus_pin[AT91_MAX_USBH_PORTS];  /* port power-control pin */
-        int             overcurrent_pin[AT91_MAX_USBH_PORTS];
-        u8              ports;                          /* number of ports on root hub */
-        u8              overcurrent_supported;
-        u8              vbus_pin_active_low[AT91_MAX_USBH_PORTS];
-        u8              overcurrent_status[AT91_MAX_USBH_PORTS];
-        u8              overcurrent_changed[AT91_MAX_USBH_PORTS];
-};
-
- /* NAND / SmartMedia */
-struct atmel_nand_data {
-        int             enable_pin;             /* chip enable */
-        int             det_pin;                /* card detect */
-        int             rdy_pin;                /* ready/busy */
-        u8              rdy_pin_active_low;     /* rdy_pin value is inverted */
-        u8              ale;                    /* address line number connected to ALE */
-        u8              cle;                    /* address line number connected to CLE */
-        u8              bus_width_16;           /* buswidth is 16 bit */
-        u8              ecc_mode;               /* ecc mode */
-        u8              on_flash_bbt;           /* bbt on flash */
-        struct mtd_partition *parts;
-        unsigned int    num_parts;
-};
-
- /* Serial */
-struct atmel_uart_data {
-        int                     num;            /* port num */
-        short                   use_dma_tx;     /* use transmit DMA? */
-        short                   use_dma_rx;     /* use receive DMA? */
-        void __iomem            *regs;          /* virt. base address, if any */
-        struct serial_rs485     rs485;          /* rs485 settings */
-};
-
- /* Touchscreen Controller */
-struct at91_tsadcc_data {
-        unsigned int    adc_clock;
-        u8              pendet_debounce;
-        u8              ts_sample_hold_time;
-};
-
-/* CAN */
-struct at91_can_data {
-        void (*transceiver_switch)(int on);
-};
-
-/* FIXME: this needs a better location, but gets stuff building again */
-extern int at91_suspend_entering_slow_clock(void);
-
-#endif /* __ATMEL_H__ */