1 files changed, 171 insertions, 0 deletions

diff --git a/drivers/net/tulip/Kconfig b/drivers/net/tulip/Kconfig
new file mode 100644
index 00000000000..1f8d4a8d8ea
--- /dev/null
+++ b/drivers/net/tulip/Kconfig
@@ -0,0 +1,171 @@
+#
+# Tulip family network device configuration
+#
+
+menuconfig NET_TULIP
+        bool "\"Tulip\" family network device support"
+        depends on PCI || EISA || CARDBUS
+        help
+          This selects the "Tulip" family of EISA/PCI network cards.
+
+if NET_TULIP
+
+config DE2104X
+        tristate "Early DECchip Tulip (dc2104x) PCI support"
+        depends on PCI
+        select CRC32
+        ---help---
+          This driver is developed for the SMC EtherPower series Ethernet
+          cards and also works with cards based on the DECchip
+          21040 (Tulip series) chips.  Some LinkSys PCI cards are
+          of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
+          (smc9332dst), you can also try the driver for "Generic DECchip"
+          cards, below.  However, most people with a network card of this type
+          will say Y here.) Do read the Ethernet-HOWTO, available from
+          <http://www.tldp.org/docs.html#howto>.
+
+          To compile this driver as a module, choose M here. The module will
+          be called de2104x.
+
+config DE2104X_DSL
+        int "Descriptor Skip Length in 32 bit longwords"
+        depends on DE2104X
+        range 0 31
+        default 0
+        help
+          Setting this value allows to align ring buffer descriptors into their
+          own cache lines. Value of 4 corresponds to the typical 32 byte line
+          (the descriptor is 16 bytes). This is necessary on systems that lack
+          cache coherence, an example is PowerMac 5500. Otherwise 0 is safe.
+          Default is 0, and range is 0 to 31.
+
+config TULIP
+        tristate "DECchip Tulip (dc2114x) PCI support"
+        depends on PCI
+        select CRC32
+        ---help---
+          This driver is developed for the SMC EtherPower series Ethernet
+          cards and also works with cards based on the DECchip 
+          21140 (Tulip series) chips.  Some LinkSys PCI cards are
+          of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
+          (smc9332dst), you can also try the driver for "Generic DECchip"
+          cards, above.  However, most people with a network card of this type
+          will say Y here.) Do read the Ethernet-HOWTO, available from
+          <http://www.tldp.org/docs.html#howto>.
+
+          To compile this driver as a module, choose M here. The module will
+          be called tulip.
+
+config TULIP_MWI
+        bool "New bus configuration (EXPERIMENTAL)"
+        depends on TULIP && EXPERIMENTAL
+        help
+          This configures your Tulip card specifically for the card and
+          system cache line size type you are using.
+
+          This is experimental code, not yet tested on many boards.
+
+          If unsure, say N.
+
+config TULIP_MMIO
+        bool "Use PCI shared mem for NIC registers"
+        depends on TULIP
+        help
+          Use PCI shared memory for the NIC registers, rather than going through
+          the Tulip's PIO (programmed I/O ports).  Faster, but could produce
+          obscure bugs if your mainboard has memory controller timing issues.
+          If in doubt, say N.
+
+config TULIP_NAPI
+        bool "Use RX polling (NAPI)"
+        depends on TULIP
+        help
+          NAPI is a new driver API designed to reduce CPU and interrupt load
+          when the driver is receiving lots of packets from the card. It is
+          still somewhat experimental and thus not yet enabled by default.
+
+          If your estimated Rx load is 10kpps or more, or if the card will be
+          deployed on potentially unfriendly networks (e.g. in a firewall),
+          then say Y here.
+
+          If in doubt, say N.
+
+config TULIP_NAPI_HW_MITIGATION
+        bool "Use Interrupt Mitigation"
+        depends on TULIP_NAPI
+        ---help---
+          Use HW to reduce RX interrupts. Not strictly necessary since NAPI
+          reduces RX interrupts by itself. Interrupt mitigation reduces RX
+          interrupts even at low levels of traffic at the cost of a small
+          latency.
+
+          If in doubt, say Y.
+
+config TULIP_DM910X
+        def_bool y
+        depends on TULIP && SPARC
+
+config DE4X5
+        tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA"
+        depends on PCI || EISA
+        select CRC32
+        ---help---
+          This is support for the DIGITAL series of PCI/EISA Ethernet cards.
+          These include the DE425, DE434, DE435, DE450 and DE500 models.  If
+          you have a network card of this type, say Y and read the
+          Ethernet-HOWTO, available from
+          <http://www.tldp.org/docs.html#howto>. More specific
+          information is contained in
+          <file:Documentation/networking/de4x5.txt>.
+
+          To compile this driver as a module, choose M here. The module will
+          be called de4x5.
+
+config WINBOND_840
+        tristate "Winbond W89c840 Ethernet support"
+        depends on PCI
+        select CRC32
+        select MII
+        help
+          This driver is for the Winbond W89c840 chip.  It also works with 
+          the TX9882 chip on the Compex RL100-ATX board.
+          More specific information and updates are available from
+          <http://www.scyld.com/network/drivers.html>.
+
+config DM9102
+        tristate "Davicom DM910x/DM980x support"
+        depends on PCI
+        select CRC32
+        ---help---
+          This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from
+          Davicom (<http://www.davicom.com.tw/>).  If you have such a network
+          (Ethernet) card, say Y.  Some information is contained in the file
+          <file:Documentation/networking/dmfe.txt>.
+
+          To compile this driver as a module, choose M here. The module will
+          be called dmfe.
+
+config ULI526X
+        tristate "ULi M526x controller support"
+        depends on PCI
+        select CRC32
+        ---help---
+          This driver is for ULi M5261/M5263 10/100M Ethernet Controller
+          (<http://www.nvidia.com/page/uli_drivers.html>).
+
+          To compile this driver as a module, choose M here. The module will
+          be called uli526x.
+          
+config PCMCIA_XIRCOM
+        tristate "Xircom CardBus support"
+        depends on CARDBUS
+        ---help---
+          This driver is for the Digital "Tulip" Ethernet CardBus adapters.
+          It should work with most DEC 21*4*-based chips/ethercards, as well
+          as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
+          ASIX.
+
+          To compile this driver as a module, choose M here. The module will
+          be called xircom_cb.  If unsure, say N.
+
+endif # NET_TULIP