1 files changed, 1775 insertions, 0 deletions

diff --git a/drivers/net/sfc/mcdi_pcol.h b/drivers/net/sfc/mcdi_pcol.h
new file mode 100644
index 00000000000..41fe06fa060
--- /dev/null
+++ b/drivers/net/sfc/mcdi_pcol.h
@@ -0,0 +1,1775 @@
+/****************************************************************************
+ * Driver for Solarflare Solarstorm network controllers and boards
+ * Copyright 2009-2011 Solarflare Communications Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation, incorporated herein by reference.
+ */
+
+
+#ifndef MCDI_PCOL_H
+#define MCDI_PCOL_H
+
+/* Values to be written into FMCR_CZ_RESET_STATE_REG to control boot. */
+/* Power-on reset state */
+#define MC_FW_STATE_POR (1)
+/* If this is set in MC_RESET_STATE_REG then it should be
+ * possible to jump into IMEM without loading code from flash. */
+#define MC_FW_WARM_BOOT_OK (2)
+/* The MC main image has started to boot. */
+#define MC_FW_STATE_BOOTING (4)
+/* The Scheduler has started. */
+#define MC_FW_STATE_SCHED (8)
+
+/* Values to be written to the per-port status dword in shared
+ * memory on reboot and assert */
+#define MC_STATUS_DWORD_REBOOT (0xb007b007)
+#define MC_STATUS_DWORD_ASSERT (0xdeaddead)
+
+/* The current version of the MCDI protocol.
+ *
+ * Note that the ROM burnt into the card only talks V0, so at the very
+ * least every driver must support version 0 and MCDI_PCOL_VERSION
+ */
+#define MCDI_PCOL_VERSION 1
+
+/**
+ * MCDI version 1
+ *
+ * Each MCDI request starts with an MCDI_HEADER, which is a 32byte
+ * structure, filled in by the client.
+ *
+ *       0       7  8     16    20     22  23  24    31
+ *      | CODE | R | LEN | SEQ | Rsvd | E | R | XFLAGS |
+ *               |                      |   |
+ *               |                      |   \--- Response
+ *               |                      \------- Error
+ *               \------------------------------ Resync (always set)
+ *
+ * The client writes it's request into MC shared memory, and rings the
+ * doorbell. Each request is completed by either by the MC writting
+ * back into shared memory, or by writting out an event.
+ *
+ * All MCDI commands support completion by shared memory response. Each
+ * request may also contain additional data (accounted for by HEADER.LEN),
+ * and some response's may also contain additional data (again, accounted
+ * for by HEADER.LEN).
+ *
+ * Some MCDI commands support completion by event, in which any associated
+ * response data is included in the event.
+ *
+ * The protocol requires one response to be delivered for every request, a
+ * request should not be sent unless the response for the previous request
+ * has been received (either by polling shared memory, or by receiving
+ * an event).
+ */
+
+/** Request/Response structure */
+#define MCDI_HEADER_OFST 0
+#define MCDI_HEADER_CODE_LBN 0
+#define MCDI_HEADER_CODE_WIDTH 7
+#define MCDI_HEADER_RESYNC_LBN 7
+#define MCDI_HEADER_RESYNC_WIDTH 1
+#define MCDI_HEADER_DATALEN_LBN 8
+#define MCDI_HEADER_DATALEN_WIDTH 8
+#define MCDI_HEADER_SEQ_LBN 16
+#define MCDI_HEADER_RSVD_LBN 20
+#define MCDI_HEADER_RSVD_WIDTH 2
+#define MCDI_HEADER_SEQ_WIDTH 4
+#define MCDI_HEADER_ERROR_LBN 22
+#define MCDI_HEADER_ERROR_WIDTH 1
+#define MCDI_HEADER_RESPONSE_LBN 23
+#define MCDI_HEADER_RESPONSE_WIDTH 1
+#define MCDI_HEADER_XFLAGS_LBN 24
+#define MCDI_HEADER_XFLAGS_WIDTH 8
+/* Request response using event */
+#define MCDI_HEADER_XFLAGS_EVREQ 0x01
+
+/* Maximum number of payload bytes */
+#define MCDI_CTL_SDU_LEN_MAX 0xfc
+
+/* The MC can generate events for two reasons:
+ *   - To complete a shared memory request if XFLAGS_EVREQ was set
+ *   - As a notification (link state, i2c event), controlled
+ *     via MC_CMD_LOG_CTRL
+ *
+ * Both events share a common structure:
+ *
+ *  0      32     33      36    44     52     60
+ * | Data | Cont | Level | Src | Code | Rsvd |
+ *           |
+ *           \ There is another event pending in this notification
+ *
+ * If Code==CMDDONE, then the fields are further interpreted as:
+ *
+ *   - LEVEL==INFO    Command succeeded
+ *   - LEVEL==ERR     Command failed
+ *
+ *    0     8         16      24     32
+ *   | Seq | Datalen | Errno | Rsvd |
+ *
+ *   These fields are taken directly out of the standard MCDI header, i.e.,
+ *   LEVEL==ERR, Datalen == 0 => Reboot
+ *
+ * Events can be squirted out of the UART (using LOG_CTRL) without a
+ * MCDI header.  An event can be distinguished from a MCDI response by
+ * examining the first byte which is 0xc0.  This corresponds to the
+ * non-existent MCDI command MC_CMD_DEBUG_LOG.
+ *
+ *      0         7        8
+ *     | command | Resync |     = 0xc0
+ *
+ * Since the event is written in big-endian byte order, this works
+ * providing bits 56-63 of the event are 0xc0.
+ *
+ *      56     60  63
+ *     | Rsvd | Code |    = 0xc0
+ *
+ * Which means for convenience the event code is 0xc for all MC
+ * generated events.
+ */
+#define FSE_AZ_EV_CODE_MCDI_EVRESPONSE 0xc
+
+#define MCDI_EVENT_DATA_LBN 0
+#define MCDI_EVENT_DATA_WIDTH 32
+#define MCDI_EVENT_CONT_LBN 32
+#define MCDI_EVENT_CONT_WIDTH 1
+#define MCDI_EVENT_LEVEL_LBN 33
+#define MCDI_EVENT_LEVEL_WIDTH 3
+#define MCDI_EVENT_LEVEL_INFO (0)
+#define MCDI_EVENT_LEVEL_WARN (1)
+#define MCDI_EVENT_LEVEL_ERR (2)
+#define MCDI_EVENT_LEVEL_FATAL (3)
+#define MCDI_EVENT_SRC_LBN 36
+#define MCDI_EVENT_SRC_WIDTH 8
+#define MCDI_EVENT_CODE_LBN 44
+#define MCDI_EVENT_CODE_WIDTH 8
+#define MCDI_EVENT_CODE_BADSSERT (1)
+#define MCDI_EVENT_CODE_PMNOTICE (2)
+#define MCDI_EVENT_CODE_CMDDONE (3)
+#define  MCDI_EVENT_CMDDONE_SEQ_LBN 0
+#define  MCDI_EVENT_CMDDONE_SEQ_WIDTH 8
+#define  MCDI_EVENT_CMDDONE_DATALEN_LBN 8
+#define  MCDI_EVENT_CMDDONE_DATALEN_WIDTH 8
+#define  MCDI_EVENT_CMDDONE_ERRNO_LBN 16
+#define  MCDI_EVENT_CMDDONE_ERRNO_WIDTH 8
+#define MCDI_EVENT_CODE_LINKCHANGE (4)
+#define  MCDI_EVENT_LINKCHANGE_LP_CAP_LBN 0
+#define  MCDI_EVENT_LINKCHANGE_LP_CAP_WIDTH 16
+#define  MCDI_EVENT_LINKCHANGE_SPEED_LBN 16
+#define  MCDI_EVENT_LINKCHANGE_SPEED_WIDTH 4
+#define  MCDI_EVENT_LINKCHANGE_SPEED_100M 1
+#define  MCDI_EVENT_LINKCHANGE_SPEED_1G 2
+#define  MCDI_EVENT_LINKCHANGE_SPEED_10G 3
+#define  MCDI_EVENT_LINKCHANGE_FCNTL_LBN 20
+#define  MCDI_EVENT_LINKCHANGE_FCNTL_WIDTH 4
+#define  MCDI_EVENT_LINKCHANGE_LINK_FLAGS_LBN 24
+#define  MCDI_EVENT_LINKCHANGE_LINK_FLAGS_WIDTH 8
+#define MCDI_EVENT_CODE_SENSOREVT (5)
+#define  MCDI_EVENT_SENSOREVT_MONITOR_LBN 0
+#define  MCDI_EVENT_SENSOREVT_MONITOR_WIDTH 8
+#define  MCDI_EVENT_SENSOREVT_STATE_LBN 8
+#define  MCDI_EVENT_SENSOREVT_STATE_WIDTH 8
+#define  MCDI_EVENT_SENSOREVT_VALUE_LBN 16
+#define  MCDI_EVENT_SENSOREVT_VALUE_WIDTH 16
+#define MCDI_EVENT_CODE_SCHEDERR (6)
+#define MCDI_EVENT_CODE_REBOOT (7)
+#define MCDI_EVENT_CODE_MAC_STATS_DMA (8)
+#define  MCDI_EVENT_MAC_STATS_DMA_GENERATION_LBN 0
+#define  MCDI_EVENT_MAC_STATS_DMA_GENERATION_WIDTH 32
+
+/* Non-existent command target */
+#define MC_CMD_ERR_ENOENT 2
+/* assert() has killed the MC */
+#define MC_CMD_ERR_EINTR 4
+/* Caller does not hold required locks */
+#define MC_CMD_ERR_EACCES 13
+/* Resource is currently unavailable (e.g. lock contention) */
+#define MC_CMD_ERR_EBUSY 16
+/* Invalid argument to target */
+#define MC_CMD_ERR_EINVAL 22
+/* Non-recursive resource is already acquired */
+#define MC_CMD_ERR_EDEADLK 35
+/* Operation not implemented */
+#define MC_CMD_ERR_ENOSYS 38
+/* Operation timed out */
+#define MC_CMD_ERR_ETIME 62
+
+#define MC_CMD_ERR_CODE_OFST 0
+
+
+/* MC_CMD_READ32: (debug, variadic out)
+ * Read multiple 32byte words from MC memory
+ */
+#define MC_CMD_READ32 0x01
+#define MC_CMD_READ32_IN_LEN 8
+#define MC_CMD_READ32_IN_ADDR_OFST 0
+#define MC_CMD_READ32_IN_NUMWORDS_OFST 4
+#define MC_CMD_READ32_OUT_LEN(_numwords) \
+        (4 * (_numwords))
+#define MC_CMD_READ32_OUT_BUFFER_OFST 0
+
+/* MC_CMD_WRITE32: (debug, variadic in)
+ * Write multiple 32byte words to MC memory
+ */
+#define MC_CMD_WRITE32 0x02
+#define MC_CMD_WRITE32_IN_LEN(_numwords) (((_numwords) * 4) + 4)
+#define MC_CMD_WRITE32_IN_ADDR_OFST 0
+#define MC_CMD_WRITE32_IN_BUFFER_OFST 4
+#define MC_CMD_WRITE32_OUT_LEN 0
+
+/* MC_CMD_COPYCODE: (debug)
+ * Copy MC code between two locations and jump
+ */
+#define MC_CMD_COPYCODE 0x03
+#define MC_CMD_COPYCODE_IN_LEN 16
+#define MC_CMD_COPYCODE_IN_SRC_ADDR_OFST 0
+#define MC_CMD_COPYCODE_IN_DEST_ADDR_OFST 4
+#define MC_CMD_COPYCODE_IN_NUMWORDS_OFST 8
+#define MC_CMD_COPYCODE_IN_JUMP_OFST 12
+/* Control should return to the caller rather than jumping */
+#define MC_CMD_COPYCODE_JUMP_NONE 1
+#define MC_CMD_COPYCODE_OUT_LEN 0
+
+/* MC_CMD_SET_FUNC: (debug)
+ * Select function for function-specific commands.
+ */
+#define MC_CMD_SET_FUNC 0x04
+#define MC_CMD_SET_FUNC_IN_LEN 4
+#define MC_CMD_SET_FUNC_IN_FUNC_OFST 0
+#define MC_CMD_SET_FUNC_OUT_LEN 0
+
+/* MC_CMD_GET_BOOT_STATUS:
+ * Get the instruction address from which the MC booted.
+ */
+#define MC_CMD_GET_BOOT_STATUS 0x05
+#define MC_CMD_GET_BOOT_STATUS_IN_LEN 0
+#define MC_CMD_GET_BOOT_STATUS_OUT_LEN 8
+#define MC_CMD_GET_BOOT_STATUS_OUT_BOOT_OFFSET_OFST 0
+#define MC_CMD_GET_BOOT_STATUS_OUT_FLAGS_OFST 4
+/* Reboot caused by watchdog */
+#define MC_CMD_GET_BOOT_STATUS_FLAGS_WATCHDOG_LBN   (0)
+#define MC_CMD_GET_BOOT_STATUS_FLAGS_WATCHDOG_WIDTH (1)
+/* MC booted from primary flash partition */
+#define MC_CMD_GET_BOOT_STATUS_FLAGS_PRIMARY_LBN    (1)
+#define MC_CMD_GET_BOOT_STATUS_FLAGS_PRIMARY_WIDTH  (1)
+/* MC booted from backup flash partition */
+#define MC_CMD_GET_BOOT_STATUS_FLAGS_BACKUP_LBN     (2)
+#define MC_CMD_GET_BOOT_STATUS_FLAGS_BACKUP_WIDTH   (1)
+
+/* MC_CMD_GET_ASSERTS: (debug, variadic out)
+ * Get (and optionally clear) the current assertion status.
+ *
+ * Only OUT.GLOBAL_FLAGS is guaranteed to exist in the completion
+ * payload. The other fields will only be present if
+ * OUT.GLOBAL_FLAGS != NO_FAILS
+ */
+#define MC_CMD_GET_ASSERTS 0x06
+#define MC_CMD_GET_ASSERTS_IN_LEN 4
+#define MC_CMD_GET_ASSERTS_IN_CLEAR_OFST 0
+#define MC_CMD_GET_ASSERTS_OUT_LEN 140
+/* Assertion status flag */
+#define MC_CMD_GET_ASSERTS_OUT_GLOBAL_FLAGS_OFST 0
+/*! No assertions have failed. */
+#define MC_CMD_GET_ASSERTS_FLAGS_NO_FAILS 1
+/*! A system-level assertion has failed. */
+#define MC_CMD_GET_ASSERTS_FLAGS_SYS_FAIL 2
+/*! A thread-level assertion has failed. */
+#define MC_CMD_GET_ASSERTS_FLAGS_THR_FAIL 3
+/*! The system was reset by the watchdog. */
+#define MC_CMD_GET_ASSERTS_FLAGS_WDOG_FIRED 4
+/* Failing PC value */
+#define MC_CMD_GET_ASSERTS_OUT_SAVED_PC_OFFS_OFST 4
+/* Saved GP regs */
+#define MC_CMD_GET_ASSERTS_OUT_GP_REGS_OFFS_OFST 8
+#define MC_CMD_GET_ASSERTS_OUT_GP_REGS_LEN 124
+/* Failing thread address */
+#define MC_CMD_GET_ASSERTS_OUT_THREAD_OFFS_OFST 132
+
+/* MC_CMD_LOG_CTRL:
+ * Determine the output stream for various events and messages
+ */
+#define MC_CMD_LOG_CTRL 0x07
+#define MC_CMD_LOG_CTRL_IN_LEN 8
+#define MC_CMD_LOG_CTRL_IN_LOG_DEST_OFST 0
+#define MC_CMD_LOG_CTRL_IN_LOG_DEST_UART (1)
+#define MC_CMD_LOG_CTRL_IN_LOG_DEST_EVQ (2)
+#define MC_CMD_LOG_CTRL_IN_LOG_DEST_EVQ_OFST 4
+#define MC_CMD_LOG_CTRL_OUT_LEN 0
+
+/* MC_CMD_GET_VERSION:
+ * Get version information about the MC firmware
+ */
+#define MC_CMD_GET_VERSION 0x08
+#define MC_CMD_GET_VERSION_IN_LEN 0
+#define MC_CMD_GET_VERSION_V0_OUT_LEN 4
+#define MC_CMD_GET_VERSION_V1_OUT_LEN 32
+#define MC_CMD_GET_VERSION_OUT_FIRMWARE_OFST 0
+/* Reserved version number to indicate "any" version. */
+#define MC_CMD_GET_VERSION_OUT_FIRMWARE_ANY 0xffffffff
+/* The version response of a boot ROM awaiting rescue */
+#define MC_CMD_GET_VERSION_OUT_FIRMWARE_BOOTROM 0xb0070000
+#define MC_CMD_GET_VERSION_V1_OUT_PCOL_OFST 4
+/* 128bit mask of functions supported by the current firmware */
+#define MC_CMD_GET_VERSION_V1_OUT_SUPPORTED_FUNCS_OFST 8
+/* The command set exported by the boot ROM (MCDI v0) */
+#define MC_CMD_GET_VERSION_V0_SUPPORTED_FUNCS {         \
+        (1 << MC_CMD_READ32)    |                       \
+        (1 << MC_CMD_WRITE32)   |                       \
+        (1 << MC_CMD_COPYCODE)  |                       \
+        (1 << MC_CMD_GET_VERSION),                      \
+        0, 0, 0 }
+#define MC_CMD_GET_VERSION_OUT_VERSION_OFST 24
+
+/* Vectors in the boot ROM */
+/* Point to the copycode entry point. */
+#define MC_BOOTROM_COPYCODE_VEC (0x7f4)
+/* Points to the recovery mode entry point. */
+#define MC_BOOTROM_NOFLASH_VEC (0x7f8)
+
+/* Test execution limits */
+#define MC_TESTEXEC_VARIANT_COUNT 16
+#define MC_TESTEXEC_RESULT_COUNT 7
+
+/* MC_CMD_SET_TESTVARS: (debug, variadic in)
+ * Write variant words for test.
+ *
+ * The user supplies a bitmap of the variants they wish to set.
+ * They must ensure that IN.LEN >= 4 + 4 * ffs(BITMAP)
+ */
+#define MC_CMD_SET_TESTVARS 0x09
+#define MC_CMD_SET_TESTVARS_IN_LEN(_numwords)   \
+  (4 + 4*(_numwords))
+#define MC_CMD_SET_TESTVARS_IN_ARGS_BITMAP_OFST 0
+/* Up to MC_TESTEXEC_VARIANT_COUNT of 32byte words start here */
+#define MC_CMD_SET_TESTVARS_IN_ARGS_BUFFER_OFST 4
+#define MC_CMD_SET_TESTVARS_OUT_LEN 0
+
+/* MC_CMD_GET_TESTRCS: (debug, variadic out)
+ * Return result words from test.
+ */
+#define MC_CMD_GET_TESTRCS 0x0a
+#define MC_CMD_GET_TESTRCS_IN_LEN 4
+#define MC_CMD_GET_TESTRCS_IN_NUMWORDS_OFST 0
+#define MC_CMD_GET_TESTRCS_OUT_LEN(_numwords) \
+        (4 * (_numwords))
+#define MC_CMD_GET_TESTRCS_OUT_BUFFER_OFST 0
+
+/* MC_CMD_RUN_TEST: (debug)
+ * Run the test exported by this firmware image
+ */
+#define MC_CMD_RUN_TEST 0x0b
+#define MC_CMD_RUN_TEST_IN_LEN 0
+#define MC_CMD_RUN_TEST_OUT_LEN 0
+
+/* MC_CMD_CSR_READ32: (debug, variadic out)
+ * Read 32bit words from the indirect memory map
+ */
+#define MC_CMD_CSR_READ32 0x0c
+#define MC_CMD_CSR_READ32_IN_LEN 12
+#define MC_CMD_CSR_READ32_IN_ADDR_OFST 0
+#define MC_CMD_CSR_READ32_IN_STEP_OFST 4
+#define MC_CMD_CSR_READ32_IN_NUMWORDS_OFST 8
+#define MC_CMD_CSR_READ32_OUT_LEN(_numwords)    \
+        (((_numwords) * 4) + 4)
+/* IN.NUMWORDS of 32bit words start here */
+#define MC_CMD_CSR_READ32_OUT_BUFFER_OFST 0
+#define MC_CMD_CSR_READ32_OUT_IREG_STATUS_OFST(_numwords)       \
+        ((_numwords) * 4)
+
+/* MC_CMD_CSR_WRITE32: (debug, variadic in)
+ * Write 32bit dwords to the indirect memory map
+ */
+#define MC_CMD_CSR_WRITE32 0x0d
+#define MC_CMD_CSR_WRITE32_IN_LEN(_numwords)    \
+        (((_numwords) * 4) + 8)
+#define MC_CMD_CSR_WRITE32_IN_ADDR_OFST 0
+#define MC_CMD_CSR_WRITE32_IN_STEP_OFST 4
+/* Multiple 32bit words of data to write start here */
+#define MC_CMD_CSR_WRITE32_IN_BUFFER_OFST 8
+#define MC_CMD_CSR_WRITE32_OUT_LEN 4
+#define MC_CMD_CSR_WRITE32_OUT_STATUS_OFST 0
+
+/* MC_CMD_JTAG_WORK: (debug, fpga only)
+ * Process JTAG work buffer for RBF acceleration.
+ *
+ *  Host: bit count, (up to) 32 words of data to clock out to JTAG
+ *   (bits 1,0=TMS,TDO for first bit; bits 3,2=TMS,TDO for second bit, etc.)
+ *  MC: bit count, (up to) 32 words of data clocked in from JTAG
+ *   (bit 0=TDI for first bit, bit 1=TDI for second bit, etc.; [31:16] unused)
+ */
+#define MC_CMD_JTAG_WORK 0x0e
+
+/* MC_CMD_STACKINFO: (debug, variadic out)
+ * Get stack information
+ *
+ * Host: nothing
+ * MC: (thread ptr, stack size, free space) for each thread in system
+ */
+#define MC_CMD_STACKINFO 0x0f
+
+/* MC_CMD_MDIO_READ:
+ * MDIO register read
+ */
+#define MC_CMD_MDIO_READ 0x10
+#define MC_CMD_MDIO_READ_IN_LEN 16
+#define MC_CMD_MDIO_READ_IN_BUS_OFST 0
+#define MC_CMD_MDIO_READ_IN_PRTAD_OFST 4
+#define MC_CMD_MDIO_READ_IN_DEVAD_OFST 8
+#define MC_CMD_MDIO_READ_IN_ADDR_OFST 12
+#define MC_CMD_MDIO_READ_OUT_LEN 8
+#define MC_CMD_MDIO_READ_OUT_VALUE_OFST 0
+#define MC_CMD_MDIO_READ_OUT_STATUS_OFST 4
+
+/* MC_CMD_MDIO_WRITE:
+ * MDIO register write
+ */
+#define MC_CMD_MDIO_WRITE 0x11
+#define MC_CMD_MDIO_WRITE_IN_LEN 20
+#define MC_CMD_MDIO_WRITE_IN_BUS_OFST 0
+#define MC_CMD_MDIO_WRITE_IN_PRTAD_OFST 4
+#define MC_CMD_MDIO_WRITE_IN_DEVAD_OFST 8
+#define MC_CMD_MDIO_WRITE_IN_ADDR_OFST 12
+#define MC_CMD_MDIO_WRITE_IN_VALUE_OFST 16
+#define MC_CMD_MDIO_WRITE_OUT_LEN 4
+#define MC_CMD_MDIO_WRITE_OUT_STATUS_OFST 0
+
+/* By default all the MCDI MDIO operations perform clause45 mode.
+ * If you want to use clause22 then set DEVAD = MC_CMD_MDIO_CLAUSE22.
+ */
+#define MC_CMD_MDIO_CLAUSE22 32
+
+/* There are two MDIO buses: one for the internal PHY, and one for external
+ * devices.
+ */
+#define MC_CMD_MDIO_BUS_INTERNAL 0
+#define MC_CMD_MDIO_BUS_EXTERNAL 1
+
+/* The MDIO commands return the raw status bits from the MDIO block.  A "good"
+ * transaction should have the DONE bit set and all other bits clear.
+ */
+#define MC_CMD_MDIO_STATUS_GOOD 0x08
+
+
+/* MC_CMD_DBI_WRITE: (debug)
+ * Write DBI register(s)
+ *
+ * Host: address, byte-enables (and VF selection, and cs2 flag),
+ *       value [,address ...]
+ * MC: nothing
+ */
+#define MC_CMD_DBI_WRITE 0x12
+#define MC_CMD_DBI_WRITE_IN_LEN(_numwords)              \
+        (12 * (_numwords))
+#define MC_CMD_DBI_WRITE_IN_ADDRESS_OFST(_word)         \
+        (((_word) * 12) + 0)
+#define MC_CMD_DBI_WRITE_IN_BYTE_MASK_OFST(_word)       \
+        (((_word) * 12) + 4)
+#define MC_CMD_DBI_WRITE_IN_VALUE_OFST(_word)           \
+        (((_word) * 12) + 8)
+#define MC_CMD_DBI_WRITE_OUT_LEN 0
+
+/* MC_CMD_DBI_READ: (debug)
+ * Read DBI register(s)
+ *
+ * Host: address, [,address ...]
+ * MC: value [,value ...]
+ * (note: this does not support reading from VFs, but is retained for backwards
+ * compatibility; see MC_CMD_DBI_READX below)
+ */
+#define MC_CMD_DBI_READ 0x13
+#define MC_CMD_DBI_READ_IN_LEN(_numwords)               \
+        (4 * (_numwords))
+#define MC_CMD_DBI_READ_OUT_LEN(_numwords)              \
+        (4 * (_numwords))
+
+/* MC_CMD_PORT_READ32: (debug)
+ * Read a 32-bit register from the indirect port register map.
+ *
+ * The port to access is implied by the Shared memory channel used.
+ */
+#define MC_CMD_PORT_READ32 0x14
+#define MC_CMD_PORT_READ32_IN_LEN 4
+#define MC_CMD_PORT_READ32_IN_ADDR_OFST 0
+#define MC_CMD_PORT_READ32_OUT_LEN 8
+#define MC_CMD_PORT_READ32_OUT_VALUE_OFST 0
+#define MC_CMD_PORT_READ32_OUT_STATUS_OFST 4
+
+/* MC_CMD_PORT_WRITE32: (debug)
+ * Write a 32-bit register to the indirect port register map.
+ *
+ * The port to access is implied by the Shared memory channel used.
+ */
+#define MC_CMD_PORT_WRITE32 0x15
+#define MC_CMD_PORT_WRITE32_IN_LEN 8
+#define MC_CMD_PORT_WRITE32_IN_ADDR_OFST 0
+#define MC_CMD_PORT_WRITE32_IN_VALUE_OFST 4
+#define MC_CMD_PORT_WRITE32_OUT_LEN 4
+#define MC_CMD_PORT_WRITE32_OUT_STATUS_OFST 0
+
+/* MC_CMD_PORT_READ128: (debug)
+ * Read a 128-bit register from indirect port register map
+ *
+ * The port to access is implied by the Shared memory channel used.
+ */
+#define MC_CMD_PORT_READ128 0x16
+#define MC_CMD_PORT_READ128_IN_LEN 4
+#define MC_CMD_PORT_READ128_IN_ADDR_OFST 0
+#define MC_CMD_PORT_READ128_OUT_LEN 20
+#define MC_CMD_PORT_READ128_OUT_VALUE_OFST 0
+#define MC_CMD_PORT_READ128_OUT_STATUS_OFST 16
+
+/* MC_CMD_PORT_WRITE128: (debug)
+ * Write a 128-bit register to indirect port register map.
+ *
+ * The port to access is implied by the Shared memory channel used.
+ */
+#define MC_CMD_PORT_WRITE128 0x17
+#define MC_CMD_PORT_WRITE128_IN_LEN 20
+#define MC_CMD_PORT_WRITE128_IN_ADDR_OFST 0
+#define MC_CMD_PORT_WRITE128_IN_VALUE_OFST 4
+#define MC_CMD_PORT_WRITE128_OUT_LEN 4
+#define MC_CMD_PORT_WRITE128_OUT_STATUS_OFST 0
+
+/* MC_CMD_GET_BOARD_CFG:
+ * Returns the MC firmware configuration structure
+ *
+ * The FW_SUBTYPE_LIST contains a 16-bit value for each of the 12 types of
+ * NVRAM area.  The values are defined in the firmware/mc/platform/<xxx>.c file
+ * for a specific board type, but otherwise have no meaning to the MC; they
+ * are used by the driver to manage selection of appropriate firmware updates.
+ */
+#define MC_CMD_GET_BOARD_CFG 0x18
+#define MC_CMD_GET_BOARD_CFG_IN_LEN 0
+#define MC_CMD_GET_BOARD_CFG_OUT_LEN 96
+#define MC_CMD_GET_BOARD_CFG_OUT_BOARD_TYPE_OFST 0
+#define MC_CMD_GET_BOARD_CFG_OUT_BOARD_NAME_OFST 4
+#define MC_CMD_GET_BOARD_CFG_OUT_BOARD_NAME_LEN 32
+#define MC_CMD_GET_BOARD_CFG_OUT_CAPABILITIES_PORT0_OFST 36
+#define MC_CMD_GET_BOARD_CFG_OUT_CAPABILITIES_PORT1_OFST 40
+#define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT0_OFST 44
+#define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT0_LEN 6
+#define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT1_OFST 50
+#define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT1_LEN 6
+#define MC_CMD_GET_BOARD_CFG_OUT_MAC_COUNT_PORT0_OFST 56
+#define MC_CMD_GET_BOARD_CFG_OUT_MAC_COUNT_PORT1_OFST 60
+#define MC_CMD_GET_BOARD_CFG_OUT_MAC_STRIDE_PORT0_OFST 64
+#define MC_CMD_GET_BOARD_CFG_OUT_MAC_STRIDE_PORT1_OFST 68
+#define MC_CMD_GET_BOARD_CFG_OUT_FW_SUBTYPE_LIST_OFST 72
+#define MC_CMD_GET_BOARD_CFG_OUT_FW_SUBTYPE_LIST_LEN 24
+
+/* MC_CMD_DBI_READX: (debug)
+ * Read DBI register(s) -- extended functionality
+ *
+ * Host: vf selection, address, [,vf selection ...]
+ * MC: value [,value ...]
+ */
+#define MC_CMD_DBI_READX 0x19
+#define MC_CMD_DBI_READX_IN_LEN(_numwords)      \
+  (8*(_numwords))
+#define MC_CMD_DBI_READX_OUT_LEN(_numwords)     \
+  (4*(_numwords))
+
+/* MC_CMD_SET_RAND_SEED:
+ * Set the 16byte seed for the MC pseudo-random generator
+ */
+#define MC_CMD_SET_RAND_SEED 0x1a
+#define MC_CMD_SET_RAND_SEED_IN_LEN 16
+#define MC_CMD_SET_RAND_SEED_IN_SEED_OFST 0
+#define MC_CMD_SET_RAND_SEED_OUT_LEN 0
+
+/* MC_CMD_LTSSM_HIST: (debug)
+ * Retrieve the history of the LTSSM, if the build supports it.
+ *
+ * Host: nothing
+ * MC: variable number of LTSSM values, as bytes
+ * The history is read-to-clear.
+ */
+#define MC_CMD_LTSSM_HIST 0x1b
+
+/* MC_CMD_DRV_ATTACH:
+ * Inform MCPU that this port is managed on the host (i.e. driver active)
+ */
+#define MC_CMD_DRV_ATTACH 0x1c
+#define MC_CMD_DRV_ATTACH_IN_LEN 8
+#define MC_CMD_DRV_ATTACH_IN_NEW_STATE_OFST 0
+#define MC_CMD_DRV_ATTACH_IN_UPDATE_OFST 4
+#define MC_CMD_DRV_ATTACH_OUT_LEN 4
+#define MC_CMD_DRV_ATTACH_OUT_OLD_STATE_OFST 0
+
+/* MC_CMD_NCSI_PROD: (debug)
+ * Trigger an NC-SI event (and possibly an AEN in response)
+ */
+#define MC_CMD_NCSI_PROD 0x1d
+#define MC_CMD_NCSI_PROD_IN_LEN 4
+#define MC_CMD_NCSI_PROD_IN_EVENTS_OFST 0
+#define MC_CMD_NCSI_PROD_LINKCHANGE_LBN 0
+#define MC_CMD_NCSI_PROD_LINKCHANGE_WIDTH 1
+#define MC_CMD_NCSI_PROD_RESET_LBN 1
+#define MC_CMD_NCSI_PROD_RESET_WIDTH 1
+#define MC_CMD_NCSI_PROD_DRVATTACH_LBN 2
+#define MC_CMD_NCSI_PROD_DRVATTACH_WIDTH 1
+#define MC_CMD_NCSI_PROD_OUT_LEN 0
+
+/* Enumeration */
+#define MC_CMD_NCSI_PROD_LINKCHANGE 0
+#define MC_CMD_NCSI_PROD_RESET 1
+#define MC_CMD_NCSI_PROD_DRVATTACH 2
+
+/* MC_CMD_DEVEL: (debug)
+ * Reserved for development
+ */
+#define MC_CMD_DEVEL 0x1e
+
+/* MC_CMD_SHMUART: (debug)
+ * Route UART output to circular buffer in shared memory instead.
+ */
+#define MC_CMD_SHMUART 0x1f
+#define MC_CMD_SHMUART_IN_FLAG_OFST 0
+#define MC_CMD_SHMUART_IN_LEN 4
+#define MC_CMD_SHMUART_OUT_LEN 0
+
+/* MC_CMD_PORT_RESET:
+ * Generic per-port reset. There is no equivalent for per-board reset.
+ *
+ * Locks required: None
+ * Return code: 0, ETIME
+ */
+#define MC_CMD_PORT_RESET 0x20
+#define MC_CMD_PORT_RESET_IN_LEN 0
+#define MC_CMD_PORT_RESET_OUT_LEN 0
+
+/* MC_CMD_RESOURCE_LOCK:
+ * Generic resource lock/unlock interface.
+ *
+ * Locks required: None
+ * Return code: 0,
+ *              EBUSY (if trylock is contended by other port),
+ *              EDEADLK (if trylock is already acquired by this port)
+ *              EINVAL (if unlock doesn't own the lock)
+ */
+#define MC_CMD_RESOURCE_LOCK 0x21
+#define MC_CMD_RESOURCE_LOCK_IN_LEN 8
+#define MC_CMD_RESOURCE_LOCK_IN_ACTION_OFST 0
+#define MC_CMD_RESOURCE_LOCK_ACTION_TRYLOCK 1
+#define MC_CMD_RESOURCE_LOCK_ACTION_UNLOCK 0
+#define MC_CMD_RESOURCE_LOCK_IN_RESOURCE_OFST 4
+#define MC_CMD_RESOURCE_LOCK_I2C 2
+#define MC_CMD_RESOURCE_LOCK_PHY 3
+#define MC_CMD_RESOURCE_LOCK_OUT_LEN 0
+
+/* MC_CMD_SPI_COMMAND: (variadic in, variadic out)
+ * Read/Write to/from the SPI device.
+ *
+ * Locks required: SPI_LOCK
+ * Return code: 0, ETIME, EINVAL, EACCES (if SPI_LOCK is not held)
+ */
+#define MC_CMD_SPI_COMMAND 0x22
+#define MC_CMD_SPI_COMMAND_IN_LEN(_write_bytes) (12 + (_write_bytes))
+#define MC_CMD_SPI_COMMAND_IN_ARGS_OFST 0
+#define MC_CMD_SPI_COMMAND_IN_ARGS_ADDRESS_OFST 0
+#define MC_CMD_SPI_COMMAND_IN_ARGS_READ_BYTES_OFST 4
+#define MC_CMD_SPI_COMMAND_IN_ARGS_CHIP_SELECT_OFST 8
+/* Data to write here */
+#define MC_CMD_SPI_COMMAND_IN_WRITE_BUFFER_OFST 12
+#define MC_CMD_SPI_COMMAND_OUT_LEN(_read_bytes) (_read_bytes)
+/* Data read here */
+#define MC_CMD_SPI_COMMAND_OUT_READ_BUFFER_OFST 0
+
+/* MC_CMD_I2C_READ_WRITE: (variadic in, variadic out)
+ * Read/Write to/from the I2C bus.
+ *
+ * Locks required: I2C_LOCK
+ * Return code: 0, ETIME, EINVAL, EACCES (if I2C_LOCK is not held)
+ */
+#define MC_CMD_I2C_RW 0x23
+#define MC_CMD_I2C_RW_IN_LEN(_write_bytes) (8 + (_write_bytes))
+#define MC_CMD_I2C_RW_IN_ARGS_OFST 0
+#define MC_CMD_I2C_RW_IN_ARGS_ADDR_OFST 0
+#define MC_CMD_I2C_RW_IN_ARGS_READ_BYTES_OFST 4
+/* Data to write here */
+#define MC_CMD_I2C_RW_IN_WRITE_BUFFER_OFSET 8
+#define MC_CMD_I2C_RW_OUT_LEN(_read_bytes) (_read_bytes)
+/* Data read here */
+#define MC_CMD_I2C_RW_OUT_READ_BUFFER_OFST 0
+
+/* Generic phy capability bitmask */
+#define MC_CMD_PHY_CAP_10HDX_LBN 1
+#define MC_CMD_PHY_CAP_10HDX_WIDTH 1
+#define MC_CMD_PHY_CAP_10FDX_LBN 2
+#define MC_CMD_PHY_CAP_10FDX_WIDTH 1
+#define MC_CMD_PHY_CAP_100HDX_LBN 3
+#define MC_CMD_PHY_CAP_100HDX_WIDTH 1
+#define MC_CMD_PHY_CAP_100FDX_LBN 4
+#define MC_CMD_PHY_CAP_100FDX_WIDTH 1
+#define MC_CMD_PHY_CAP_1000HDX_LBN 5
+#define MC_CMD_PHY_CAP_1000HDX_WIDTH 1
+#define MC_CMD_PHY_CAP_1000FDX_LBN 6
+#define MC_CMD_PHY_CAP_1000FDX_WIDTH 1
+#define MC_CMD_PHY_CAP_10000FDX_LBN 7
+#define MC_CMD_PHY_CAP_10000FDX_WIDTH 1
+#define MC_CMD_PHY_CAP_PAUSE_LBN 8
+#define MC_CMD_PHY_CAP_PAUSE_WIDTH 1
+#define MC_CMD_PHY_CAP_ASYM_LBN 9
+#define MC_CMD_PHY_CAP_ASYM_WIDTH 1
+#define MC_CMD_PHY_CAP_AN_LBN 10
+#define MC_CMD_PHY_CAP_AN_WIDTH 1
+
+/* Generic loopback enumeration */
+#define MC_CMD_LOOPBACK_NONE 0
+#define MC_CMD_LOOPBACK_DATA 1
+#define MC_CMD_LOOPBACK_GMAC 2
+#define MC_CMD_LOOPBACK_XGMII 3
+#define MC_CMD_LOOPBACK_XGXS 4
+#define MC_CMD_LOOPBACK_XAUI 5
+#define MC_CMD_LOOPBACK_GMII 6
+#define MC_CMD_LOOPBACK_SGMII 7
+#define MC_CMD_LOOPBACK_XGBR 8
+#define MC_CMD_LOOPBACK_XFI 9
+#define MC_CMD_LOOPBACK_XAUI_FAR 10
+#define MC_CMD_LOOPBACK_GMII_FAR 11
+#define MC_CMD_LOOPBACK_SGMII_FAR 12
+#define MC_CMD_LOOPBACK_XFI_FAR 13
+#define MC_CMD_LOOPBACK_GPHY 14
+#define MC_CMD_LOOPBACK_PHYXS 15
+#define MC_CMD_LOOPBACK_PCS 16
+#define MC_CMD_LOOPBACK_PMAPMD 17
+#define MC_CMD_LOOPBACK_XPORT 18
+#define MC_CMD_LOOPBACK_XGMII_WS 19
+#define MC_CMD_LOOPBACK_XAUI_WS 20
+#define MC_CMD_LOOPBACK_XAUI_WS_FAR 21
+#define MC_CMD_LOOPBACK_XAUI_WS_NEAR 22
+#define MC_CMD_LOOPBACK_GMII_WS 23
+#define MC_CMD_LOOPBACK_XFI_WS 24
+#define MC_CMD_LOOPBACK_XFI_WS_FAR 25
+#define MC_CMD_LOOPBACK_PHYXS_WS 26
+
+/* Generic PHY statistics enumeration */
+#define MC_CMD_OUI 0
+#define MC_CMD_PMA_PMD_LINK_UP 1
+#define MC_CMD_PMA_PMD_RX_FAULT 2
+#define MC_CMD_PMA_PMD_TX_FAULT 3
+#define MC_CMD_PMA_PMD_SIGNAL 4
+#define MC_CMD_PMA_PMD_SNR_A 5
+#define MC_CMD_PMA_PMD_SNR_B 6
+#define MC_CMD_PMA_PMD_SNR_C 7
+#define MC_CMD_PMA_PMD_SNR_D 8
+#define MC_CMD_PCS_LINK_UP 9
+#define MC_CMD_PCS_RX_FAULT 10
+#define MC_CMD_PCS_TX_FAULT 11
+#define MC_CMD_PCS_BER 12
+#define MC_CMD_PCS_BLOCK_ERRORS 13
+#define MC_CMD_PHYXS_LINK_UP 14
+#define MC_CMD_PHYXS_RX_FAULT 15
+#define MC_CMD_PHYXS_TX_FAULT 16
+#define MC_CMD_PHYXS_ALIGN 17
+#define MC_CMD_PHYXS_SYNC 18
+#define MC_CMD_AN_LINK_UP 19
+#define MC_CMD_AN_COMPLETE 20
+#define MC_CMD_AN_10GBT_STATUS 21
+#define MC_CMD_CL22_LINK_UP 22
+#define MC_CMD_PHY_NSTATS 23
+
+/* MC_CMD_GET_PHY_CFG:
+ * Report PHY configuration.  This guarantees to succeed even if the PHY is in
+ * a "zombie" state.
+ *
+ * Locks required: None
+ * Return code: 0
+ */
+#define MC_CMD_GET_PHY_CFG 0x24
+
+#define MC_CMD_GET_PHY_CFG_IN_LEN 0
+#define MC_CMD_GET_PHY_CFG_OUT_LEN 72
+
+#define MC_CMD_GET_PHY_CFG_OUT_FLAGS_OFST 0
+#define MC_CMD_GET_PHY_CFG_PRESENT_LBN 0
+#define MC_CMD_GET_PHY_CFG_PRESENT_WIDTH 1
+#define MC_CMD_GET_PHY_CFG_BIST_CABLE_SHORT_LBN 1
+#define MC_CMD_GET_PHY_CFG_BIST_CABLE_SHORT_WIDTH 1
+#define MC_CMD_GET_PHY_CFG_BIST_CABLE_LONG_LBN 2
+#define MC_CMD_GET_PHY_CFG_BIST_CABLE_LONG_WIDTH 1
+#define MC_CMD_GET_PHY_CFG_LOWPOWER_LBN 3
+#define MC_CMD_GET_PHY_CFG_LOWPOWER_WIDTH 1
+#define MC_CMD_GET_PHY_CFG_POWEROFF_LBN 4
+#define MC_CMD_GET_PHY_CFG_POWEROFF_WIDTH 1
+#define MC_CMD_GET_PHY_CFG_TXDIS_LBN 5
+#define MC_CMD_GET_PHY_CFG_TXDIS_WIDTH 1
+#define MC_CMD_GET_PHY_CFG_BIST_LBN 6
+#define MC_CMD_GET_PHY_CFG_BIST_WIDTH 1
+#define MC_CMD_GET_PHY_CFG_OUT_TYPE_OFST 4
+/* Bitmask of supported capabilities */
+#define MC_CMD_GET_PHY_CFG_OUT_SUPPORTED_CAP_OFST 8
+#define MC_CMD_GET_PHY_CFG_OUT_CHANNEL_OFST 12
+#define MC_CMD_GET_PHY_CFG_OUT_PRT_OFST 16
+/* PHY statistics bitmap */
+#define MC_CMD_GET_PHY_CFG_OUT_STATS_MASK_OFST 20
+/* PHY type/name string */
+#define MC_CMD_GET_PHY_CFG_OUT_NAME_OFST 24
+#define MC_CMD_GET_PHY_CFG_OUT_NAME_LEN 20
+#define MC_CMD_GET_PHY_CFG_OUT_MEDIA_TYPE_OFST 44
+#define MC_CMD_MEDIA_XAUI 1
+#define MC_CMD_MEDIA_CX4 2
+#define MC_CMD_MEDIA_KX4 3
+#define MC_CMD_MEDIA_XFP 4
+#define MC_CMD_MEDIA_SFP_PLUS 5
+#define MC_CMD_MEDIA_BASE_T 6
+/* MDIO "MMDS" supported */
+#define MC_CMD_GET_PHY_CFG_OUT_MMD_MASK_OFST 48
+/* Native clause 22 */
+#define MC_CMD_MMD_CLAUSE22  0
+#define MC_CMD_MMD_CLAUSE45_PMAPMD 1
+#define MC_CMD_MMD_CLAUSE45_WIS 2
+#define MC_CMD_MMD_CLAUSE45_PCS 3
+#define MC_CMD_MMD_CLAUSE45_PHYXS 4
+#define MC_CMD_MMD_CLAUSE45_DTEXS 5
+#define MC_CMD_MMD_CLAUSE45_TC 6
+#define MC_CMD_MMD_CLAUSE45_AN 7
+/* Clause22 proxied over clause45 by PHY */
+#define MC_CMD_MMD_CLAUSE45_C22EXT 29
+#define MC_CMD_MMD_CLAUSE45_VEND1 30
+#define MC_CMD_MMD_CLAUSE45_VEND2 31
+/* PHY stepping version */
+#define MC_CMD_GET_PHY_CFG_OUT_REVISION_OFST 52
+#define MC_CMD_GET_PHY_CFG_OUT_REVISION_LEN 20
+
+/* MC_CMD_START_BIST:
+ * Start a BIST test on the PHY.
+ *
+ * Locks required: PHY_LOCK if doing a  PHY BIST
+ * Return code: 0, EINVAL, EACCES (if PHY_LOCK is not held)
+ */
+#define MC_CMD_START_BIST 0x25
+#define MC_CMD_START_BIST_IN_LEN 4
+#define MC_CMD_START_BIST_IN_TYPE_OFST 0
+#define MC_CMD_START_BIST_OUT_LEN 0
+
+/* Run the PHY's short cable BIST */
+#define MC_CMD_PHY_BIST_CABLE_SHORT  1
+/* Run the PHY's long cable BIST */
+#define MC_CMD_PHY_BIST_CABLE_LONG   2
+/* Run BIST on the currently selected BPX Serdes (XAUI or XFI) */
+#define MC_CMD_BPX_SERDES_BIST 3
+/* Run the MC loopback tests */
+#define MC_CMD_MC_LOOPBACK_BIST 4
+/* Run the PHY's standard BIST */
+#define MC_CMD_PHY_BIST 5
+
+/* MC_CMD_POLL_PHY_BIST: (variadic output)
+ * Poll for BIST completion
+ *
+ * Returns a single status code, and optionally some PHY specific
+ * bist output. The driver should only consume the BIST output
+ * after validating OUTLEN and PHY_CFG.PHY_TYPE.
+ *
+ * If a driver can't successfully parse the BIST output, it should
+ * still respect the pass/Fail in OUT.RESULT
+ *
+ * Locks required: PHY_LOCK if doing a  PHY BIST
+ * Return code: 0, EACCES (if PHY_LOCK is not held)
+ */
+#define MC_CMD_POLL_BIST 0x26
+#define MC_CMD_POLL_BIST_IN_LEN 0
+#define MC_CMD_POLL_BIST_OUT_LEN UNKNOWN
+#define MC_CMD_POLL_BIST_OUT_SFT9001_LEN 36
+#define MC_CMD_POLL_BIST_OUT_MRSFP_LEN 8
+#define MC_CMD_POLL_BIST_OUT_RESULT_OFST 0
+#define MC_CMD_POLL_BIST_RUNNING 1
+#define MC_CMD_POLL_BIST_PASSED 2
+#define MC_CMD_POLL_BIST_FAILED 3
+#define MC_CMD_POLL_BIST_TIMEOUT 4
+/* Generic: */
+#define MC_CMD_POLL_BIST_OUT_PRIVATE_OFST 4
+/* SFT9001-specific: */
+#define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_A_OFST 4
+#define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_B_OFST 8
+#define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_C_OFST 12
+#define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_D_OFST 16
+#define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_A_OFST 20
+#define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_B_OFST 24
+#define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_C_OFST 28
+#define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_D_OFST 32
+#define MC_CMD_POLL_BIST_SFT9001_PAIR_OK 1
+#define MC_CMD_POLL_BIST_SFT9001_PAIR_OPEN 2
+#define MC_CMD_POLL_BIST_SFT9001_INTRA_PAIR_SHORT 3
+#define MC_CMD_POLL_BIST_SFT9001_INTER_PAIR_SHORT 4
+#define MC_CMD_POLL_BIST_SFT9001_PAIR_BUSY 9
+/* mrsfp "PHY" driver: */
+#define MC_CMD_POLL_BIST_OUT_MRSFP_TEST_OFST 4
+#define MC_CMD_POLL_BIST_MRSFP_TEST_COMPLETE 0
+#define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_OFF_I2C_WRITE 1
+#define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_OFF_I2C_NO_ACCESS_IO_EXP 2
+#define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_OFF_I2C_NO_ACCESS_MODULE 3
+#define MC_CMD_POLL_BIST_MRSFP_TEST_IO_EXP_I2C_CONFIGURE 4
+#define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_I2C_NO_CROSSTALK 5
+#define MC_CMD_POLL_BIST_MRSFP_TEST_MODULE_PRESENCE 6
+#define MC_CMD_POLL_BIST_MRSFP_TEST_MODULE_ID_I2C_ACCESS 7
+#define MC_CMD_POLL_BIST_MRSFP_TEST_MODULE_ID_SANE_VALUE 8
+
+/* MC_CMD_PHY_SPI: (variadic in, variadic out)
+ * Read/Write/Erase the PHY SPI device
+ *
+ * Locks required: PHY_LOCK
+ * Return code: 0, ETIME, EINVAL, EACCES (if PHY_LOCK is not held)
+ */
+#define MC_CMD_PHY_SPI 0x27
+#define MC_CMD_PHY_SPI_IN_LEN(_write_bytes) (12 + (_write_bytes))
+#define MC_CMD_PHY_SPI_IN_ARGS_OFST 0
+#define MC_CMD_PHY_SPI_IN_ARGS_ADDR_OFST 0
+#define MC_CMD_PHY_SPI_IN_ARGS_READ_BYTES_OFST 4
+#define MC_CMD_PHY_SPI_IN_ARGS_ERASE_ALL_OFST 8
+/* Data to write here */
+#define MC_CMD_PHY_SPI_IN_WRITE_BUFFER_OFSET 12
+#define MC_CMD_PHY_SPI_OUT_LEN(_read_bytes) (_read_bytes)
+/* Data read here */
+#define MC_CMD_PHY_SPI_OUT_READ_BUFFER_OFST 0
+
+
+/* MC_CMD_GET_LOOPBACK_MODES:
+ * Returns a bitmask of loopback modes evailable at each speed.
+ *
+ * Locks required: None
+ * Return code: 0
+ */
+#define MC_CMD_GET_LOOPBACK_MODES 0x28
+#define MC_CMD_GET_LOOPBACK_MODES_IN_LEN 0
+#define MC_CMD_GET_LOOPBACK_MODES_OUT_LEN 32
+#define MC_CMD_GET_LOOPBACK_MODES_100M_OFST 0
+#define MC_CMD_GET_LOOPBACK_MODES_1G_OFST 8
+#define MC_CMD_GET_LOOPBACK_MODES_10G_OFST 16
+#define MC_CMD_GET_LOOPBACK_MODES_SUGGESTED_OFST 24
+
+/* Flow control enumeration */
+#define MC_CMD_FCNTL_OFF 0
+#define MC_CMD_FCNTL_RESPOND 1
+#define MC_CMD_FCNTL_BIDIR 2
+/* Auto - Use what the link has autonegotiated
+ *      - The driver should modify the advertised capabilities via SET_LINK.CAP
+ *        to control the negotiated flow control mode.
+ *      - Can only be set if the PHY supports PAUSE+ASYM capabilities
+ *      - Never returned by GET_LINK as the value programmed into the MAC
+ */
+#define MC_CMD_FCNTL_AUTO 3
+
+/* Generic mac fault bitmask */
+#define MC_CMD_MAC_FAULT_XGMII_LOCAL_LBN 0
+#define MC_CMD_MAC_FAULT_XGMII_LOCAL_WIDTH 1
+#define MC_CMD_MAC_FAULT_XGMII_REMOTE_LBN 1
+#define MC_CMD_MAC_FAULT_XGMII_REMOTE_WIDTH 1
+#define MC_CMD_MAC_FAULT_SGMII_REMOTE_LBN 2
+#define MC_CMD_MAC_FAULT_SGMII_REMOTE_WIDTH 1
+
+/* MC_CMD_GET_LINK:
+ * Read the unified MAC/PHY link state
+ *
+ * Locks required: None
+ * Return code: 0, ETIME
+ */
+#define MC_CMD_GET_LINK 0x29
+#define MC_CMD_GET_LINK_IN_LEN 0
+#define MC_CMD_GET_LINK_OUT_LEN 28
+/* near-side and link-partner advertised capabilities */
+#define MC_CMD_GET_LINK_OUT_CAP_OFST 0
+#define MC_CMD_GET_LINK_OUT_LP_CAP_OFST 4
+/* Autonegotiated speed in mbit/s. The link may still be down
+ * even if this reads non-zero */
+#define MC_CMD_GET_LINK_OUT_LINK_SPEED_OFST 8
+#define MC_CMD_GET_LINK_OUT_LOOPBACK_MODE_OFST 12
+#define MC_CMD_GET_LINK_OUT_FLAGS_OFST 16
+/* Whether we have overall link up */
+#define MC_CMD_GET_LINK_LINK_UP_LBN 0
+#define MC_CMD_GET_LINK_LINK_UP_WIDTH 1
+#define MC_CMD_GET_LINK_FULL_DUPLEX_LBN 1
+#define MC_CMD_GET_LINK_FULL_DUPLEX_WIDTH 1
+/* Whether we have link at the layers provided by the BPX */
+#define MC_CMD_GET_LINK_BPX_LINK_LBN 2
+#define MC_CMD_GET_LINK_BPX_LINK_WIDTH 1
+/* Whether the PHY has external link */
+#define MC_CMD_GET_LINK_PHY_LINK_LBN 3
+#define MC_CMD_GET_LINK_PHY_LINK_WIDTH 1
+#define MC_CMD_GET_LINK_OUT_FCNTL_OFST 20
+#define MC_CMD_GET_LINK_OUT_MAC_FAULT_OFST 24
+
+/* MC_CMD_SET_LINK:
+ * Write the unified MAC/PHY link configuration
+ *
+ * A loopback speed of "0" is supported, and means
+ * (choose any available speed)
+ *
+ * Locks required: None
+ * Return code: 0, EINVAL, ETIME
+ */
+#define MC_CMD_SET_LINK 0x2a
+#define MC_CMD_SET_LINK_IN_LEN 16
+#define MC_CMD_SET_LINK_IN_CAP_OFST 0
+#define MC_CMD_SET_LINK_IN_FLAGS_OFST 4
+#define MC_CMD_SET_LINK_LOWPOWER_LBN 0
+#define MC_CMD_SET_LINK_LOWPOWER_WIDTH 1
+#define MC_CMD_SET_LINK_POWEROFF_LBN 1
+#define MC_CMD_SET_LINK_POWEROFF_WIDTH 1
+#define MC_CMD_SET_LINK_TXDIS_LBN 2
+#define MC_CMD_SET_LINK_TXDIS_WIDTH 1
+#define MC_CMD_SET_LINK_IN_LOOPBACK_MODE_OFST 8
+#define MC_CMD_SET_LINK_IN_LOOPBACK_SPEED_OFST 12
+#define MC_CMD_SET_LINK_OUT_LEN 0
+
+/* MC_CMD_SET_ID_LED:
+ * Set indentification LED state
+ *
+ * Locks required: None
+ * Return code: 0, EINVAL
+ */
+#define MC_CMD_SET_ID_LED 0x2b
+#define MC_CMD_SET_ID_LED_IN_LEN 4
+#define MC_CMD_SET_ID_LED_IN_STATE_OFST 0
+#define  MC_CMD_LED_OFF 0
+#define  MC_CMD_LED_ON 1
+#define  MC_CMD_LED_DEFAULT 2
+#define MC_CMD_SET_ID_LED_OUT_LEN 0
+
+/* MC_CMD_SET_MAC:
+ * Set MAC configuration
+ *
+ * The MTU is the MTU programmed directly into the XMAC/GMAC
+ * (inclusive of EtherII, VLAN, bug16011 padding)
+ *
+ * Locks required: None
+ * Return code: 0, EINVAL
+ */
+#define MC_CMD_SET_MAC 0x2c
+#define MC_CMD_SET_MAC_IN_LEN 24
+#define MC_CMD_SET_MAC_IN_MTU_OFST 0
+#define MC_CMD_SET_MAC_IN_DRAIN_OFST 4
+#define MC_CMD_SET_MAC_IN_ADDR_OFST 8
+#define MC_CMD_SET_MAC_IN_REJECT_OFST 16
+#define MC_CMD_SET_MAC_IN_REJECT_UNCST_LBN 0
+#define MC_CMD_SET_MAC_IN_REJECT_UNCST_WIDTH 1
+#define MC_CMD_SET_MAC_IN_REJECT_BRDCST_LBN 1
+#define MC_CMD_SET_MAC_IN_REJECT_BRDCST_WIDTH 1
+#define MC_CMD_SET_MAC_IN_FCNTL_OFST 20
+#define MC_CMD_SET_MAC_OUT_LEN 0
+
+/* MC_CMD_PHY_STATS:
+ * Get generic PHY statistics
+ *
+ * This call returns the statistics for a generic PHY in a sparse
+ * array (indexed by the enumerate). Each value is represented by
+ * a 32bit number.
+ *
+ * If the DMA_ADDR is 0, then no DMA is performed, and the statistics
+ * may be read directly out of shared memory. If DMA_ADDR != 0, then
+ * the statistics are dmad to that (page-aligned location)
+ *
+ * Locks required: None
+ * Returns: 0, ETIME
+ * Response methods: shared memory, event
+ */
+#define MC_CMD_PHY_STATS 0x2d
+#define MC_CMD_PHY_STATS_IN_LEN 8
+#define MC_CMD_PHY_STATS_IN_DMA_ADDR_LO_OFST 0
+#define MC_CMD_PHY_STATS_IN_DMA_ADDR_HI_OFST 4
+#define MC_CMD_PHY_STATS_OUT_DMA_LEN 0
+#define MC_CMD_PHY_STATS_OUT_NO_DMA_LEN (MC_CMD_PHY_NSTATS * 4)
+
+/* Unified MAC statistics enumeration */
+#define MC_CMD_MAC_GENERATION_START 0
+#define MC_CMD_MAC_TX_PKTS 1
+#define MC_CMD_MAC_TX_PAUSE_PKTS 2
+#define MC_CMD_MAC_TX_CONTROL_PKTS 3
+#define MC_CMD_MAC_TX_UNICAST_PKTS 4
+#define MC_CMD_MAC_TX_MULTICAST_PKTS 5
+#define MC_CMD_MAC_TX_BROADCAST_PKTS 6
+#define MC_CMD_MAC_TX_BYTES 7
+#define MC_CMD_MAC_TX_BAD_BYTES 8
+#define MC_CMD_MAC_TX_LT64_PKTS 9
+#define MC_CMD_MAC_TX_64_PKTS 10
+#define MC_CMD_MAC_TX_65_TO_127_PKTS 11
+#define MC_CMD_MAC_TX_128_TO_255_PKTS 12
+#define MC_CMD_MAC_TX_256_TO_511_PKTS 13
+#define MC_CMD_MAC_TX_512_TO_1023_PKTS 14
+#define MC_CMD_MAC_TX_1024_TO_15XX_PKTS 15
+#define MC_CMD_MAC_TX_15XX_TO_JUMBO_PKTS 16
+#define MC_CMD_MAC_TX_GTJUMBO_PKTS 17
+#define MC_CMD_MAC_TX_BAD_FCS_PKTS 18
+#define MC_CMD_MAC_TX_SINGLE_COLLISION_PKTS 19
+#define MC_CMD_MAC_TX_MULTIPLE_COLLISION_PKTS 20
+#define MC_CMD_MAC_TX_EXCESSIVE_COLLISION_PKTS 21
+#define MC_CMD_MAC_TX_LATE_COLLISION_PKTS 22
+#define MC_CMD_MAC_TX_DEFERRED_PKTS 23
+#define MC_CMD_MAC_TX_EXCESSIVE_DEFERRED_PKTS 24
+#define MC_CMD_MAC_TX_NON_TCPUDP_PKTS 25
+#define MC_CMD_MAC_TX_MAC_SRC_ERR_PKTS 26
+#define MC_CMD_MAC_TX_IP_SRC_ERR_PKTS 27
+#define MC_CMD_MAC_RX_PKTS 28
+#define MC_CMD_MAC_RX_PAUSE_PKTS 29
+#define MC_CMD_MAC_RX_GOOD_PKTS 30
+#define MC_CMD_MAC_RX_CONTROL_PKTS 31
+#define MC_CMD_MAC_RX_UNICAST_PKTS 32
+#define MC_CMD_MAC_RX_MULTICAST_PKTS 33
+#define MC_CMD_MAC_RX_BROADCAST_PKTS 34
+#define MC_CMD_MAC_RX_BYTES 35
+#define MC_CMD_MAC_RX_BAD_BYTES 36
+#define MC_CMD_MAC_RX_64_PKTS 37
+#define MC_CMD_MAC_RX_65_TO_127_PKTS 38
+#define MC_CMD_MAC_RX_128_TO_255_PKTS 39
+#define MC_CMD_MAC_RX_256_TO_511_PKTS 40
+#define MC_CMD_MAC_RX_512_TO_1023_PKTS 41
+#define MC_CMD_MAC_RX_1024_TO_15XX_PKTS 42
+#define MC_CMD_MAC_RX_15XX_TO_JUMBO_PKTS 43
+#define MC_CMD_MAC_RX_GTJUMBO_PKTS 44
+#define MC_CMD_MAC_RX_UNDERSIZE_PKTS 45
+#define MC_CMD_MAC_RX_BAD_FCS_PKTS 46
+#define MC_CMD_MAC_RX_OVERFLOW_PKTS 47
+#define MC_CMD_MAC_RX_FALSE_CARRIER_PKTS 48
+#define MC_CMD_MAC_RX_SYMBOL_ERROR_PKTS 49
+#define MC_CMD_MAC_RX_ALIGN_ERROR_PKTS 50
+#define MC_CMD_MAC_RX_LENGTH_ERROR_PKTS 51
+#define MC_CMD_MAC_RX_INTERNAL_ERROR_PKTS 52
+#define MC_CMD_MAC_RX_JABBER_PKTS 53
+#define MC_CMD_MAC_RX_NODESC_DROPS 54
+#define MC_CMD_MAC_RX_LANES01_CHAR_ERR 55
+#define MC_CMD_MAC_RX_LANES23_CHAR_ERR 56
+#define MC_CMD_MAC_RX_LANES01_DISP_ERR 57
+#define MC_CMD_MAC_RX_LANES23_DISP_ERR 58
+#define MC_CMD_MAC_RX_MATCH_FAULT 59
+#define MC_CMD_GMAC_DMABUF_START 64
+#define MC_CMD_GMAC_DMABUF_END   95
+/* Insert new members here. */
+#define MC_CMD_MAC_GENERATION_END 96
+#define MC_CMD_MAC_NSTATS (MC_CMD_MAC_GENERATION_END+1)
+
+/* MC_CMD_MAC_STATS:
+ * Get unified GMAC/XMAC statistics
+ *
+ * This call returns unified statistics maintained by the MC as it
+ * switches between the GMAC and XMAC. The MC will write out all
+ * supported stats.  The driver should zero initialise the buffer to
+ * guarantee consistent results.
+ *
+ * Locks required: None
+ * Returns: 0
+ * Response methods: shared memory, event
+ */
+#define MC_CMD_MAC_STATS 0x2e
+#define MC_CMD_MAC_STATS_IN_LEN 16
+#define MC_CMD_MAC_STATS_IN_DMA_ADDR_LO_OFST 0
+#define MC_CMD_MAC_STATS_IN_DMA_ADDR_HI_OFST 4
+#define MC_CMD_MAC_STATS_IN_CMD_OFST 8
+#define MC_CMD_MAC_STATS_CMD_DMA_LBN 0
+#define MC_CMD_MAC_STATS_CMD_DMA_WIDTH 1
+#define MC_CMD_MAC_STATS_CMD_CLEAR_LBN 1
+#define MC_CMD_MAC_STATS_CMD_CLEAR_WIDTH 1
+#define MC_CMD_MAC_STATS_CMD_PERIODIC_CHANGE_LBN 2
+#define MC_CMD_MAC_STATS_CMD_PERIODIC_CHANGE_WIDTH 1
+/* Remaining PERIOD* fields only relevant when PERIODIC_CHANGE is set */
+#define MC_CMD_MAC_STATS_CMD_PERIODIC_ENABLE_LBN 3
+#define MC_CMD_MAC_STATS_CMD_PERIODIC_ENABLE_WIDTH 1
+#define MC_CMD_MAC_STATS_CMD_PERIODIC_CLEAR_LBN 4
+#define MC_CMD_MAC_STATS_CMD_PERIODIC_CLEAR_WIDTH 1
+#define MC_CMD_MAC_STATS_CMD_PERIODIC_NOEVENT_LBN 5
+#define MC_CMD_MAC_STATS_CMD_PERIODIC_NOEVENT_WIDTH 1
+#define MC_CMD_MAC_STATS_CMD_PERIOD_MS_LBN 16
+#define MC_CMD_MAC_STATS_CMD_PERIOD_MS_WIDTH 16
+#define MC_CMD_MAC_STATS_IN_DMA_LEN_OFST 12
+
+#define MC_CMD_MAC_STATS_OUT_LEN 0
+
+/* Callisto flags */
+#define MC_CMD_SFT9001_ROBUST_LBN 0
+#define MC_CMD_SFT9001_ROBUST_WIDTH 1
+#define MC_CMD_SFT9001_SHORT_REACH_LBN 1
+#define MC_CMD_SFT9001_SHORT_REACH_WIDTH 1
+
+/* MC_CMD_SFT9001_GET:
+ * Read current callisto specific setting
+ *
+ * Locks required: None
+ * Returns: 0, ETIME
+ */
+#define MC_CMD_SFT9001_GET 0x30
+#define MC_CMD_SFT9001_GET_IN_LEN 0
+#define MC_CMD_SFT9001_GET_OUT_LEN 4
+#define MC_CMD_SFT9001_GET_OUT_FLAGS_OFST 0
+
+/* MC_CMD_SFT9001_SET:
+ * Write current callisto specific setting
+ *
+ * Locks required: None
+ * Returns: 0, ETIME, EINVAL
+ */
+#define MC_CMD_SFT9001_SET 0x31
+#define MC_CMD_SFT9001_SET_IN_LEN 4
+#define MC_CMD_SFT9001_SET_IN_FLAGS_OFST 0
+#define MC_CMD_SFT9001_SET_OUT_LEN 0
+
+
+/* MC_CMD_WOL_FILTER_SET:
+ * Set a WoL filter
+ *
+ * Locks required: None
+ * Returns: 0, EBUSY, EINVAL, ENOSYS
+ */
+#define MC_CMD_WOL_FILTER_SET 0x32
+#define MC_CMD_WOL_FILTER_SET_IN_LEN 192 /* 190 rounded up to a word */
+#define MC_CMD_WOL_FILTER_SET_IN_FILTER_MODE_OFST 0
+#define MC_CMD_WOL_FILTER_SET_IN_WOL_TYPE_OFST 4
+
+/* There is a union at offset 8, following defines overlap due to
+ * this */
+#define MC_CMD_WOL_FILTER_SET_IN_DATA_OFST 8
+
+#define MC_CMD_WOL_FILTER_SET_IN_MAGIC_MAC_OFST         \
+        MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
+
+#define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_SRC_IP_OFST   \
+        MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
+#define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_DST_IP_OFST   \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 4)
+#define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_SRC_PORT_OFST \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 8)
+#define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_DST_PORT_OFST \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 10)
+
+#define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_SRC_IP_OFST   \
+        MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
+#define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_DST_IP_OFST   \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 16)
+#define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_SRC_PORT_OFST \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 32)
+#define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_DST_PORT_OFST \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 34)
+
+#define MC_CMD_WOL_FILTER_SET_IN_BITMAP_MASK_OFST       \
+        MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
+#define MC_CMD_WOL_FILTER_SET_IN_BITMAP_OFST            \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 48)
+#define MC_CMD_WOL_FILTER_SET_IN_BITMAP_LEN_OFST        \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 176)
+#define MC_CMD_WOL_FILTER_SET_IN_BITMAP_LAYER3_OFST     \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 177)
+#define MC_CMD_WOL_FILTER_SET_IN_BITMAP_LAYER4_OFST     \
+        (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 178)
+
+#define MC_CMD_WOL_FILTER_SET_IN_LINK_MASK_OFST \
+        MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
+#define MC_CMD_WOL_FILTER_SET_IN_LINK_UP_LBN    0
+#define MC_CMD_WOL_FILTER_SET_IN_LINK_UP_WIDTH  1
+#define MC_CMD_WOL_FILTER_SET_IN_LINK_DOWN_LBN  1
+#define MC_CMD_WOL_FILTER_SET_IN_LINK_DOWN_WIDTH 1
+
+#define MC_CMD_WOL_FILTER_SET_OUT_LEN 4
+#define MC_CMD_WOL_FILTER_SET_OUT_FILTER_ID_OFST 0
+
+/* WOL Filter types enumeration */
+#define MC_CMD_WOL_TYPE_MAGIC      0x0
+                         /* unused 0x1 */
+#define MC_CMD_WOL_TYPE_WIN_MAGIC  0x2
+#define MC_CMD_WOL_TYPE_IPV4_SYN   0x3
+#define MC_CMD_WOL_TYPE_IPV6_SYN   0x4
+#define MC_CMD_WOL_TYPE_BITMAP     0x5
+#define MC_CMD_WOL_TYPE_LINK       0x6
+#define MC_CMD_WOL_TYPE_MAX        0x7
+
+#define MC_CMD_FILTER_MODE_SIMPLE     0x0
+#define MC_CMD_FILTER_MODE_STRUCTURED 0xffffffff
+
+/* MC_CMD_WOL_FILTER_REMOVE:
+ * Remove a WoL filter
+ *
+ * Locks required: None
+ * Returns: 0, EINVAL, ENOSYS
+ */
+#define MC_CMD_WOL_FILTER_REMOVE 0x33
+#define MC_CMD_WOL_FILTER_REMOVE_IN_LEN 4
+#define MC_CMD_WOL_FILTER_REMOVE_IN_FILTER_ID_OFST 0
+#define MC_CMD_WOL_FILTER_REMOVE_OUT_LEN 0
+
+
+/* MC_CMD_WOL_FILTER_RESET:
+ * Reset (i.e. remove all) WoL filters
+ *
+ * Locks required: None
+ * Returns: 0, ENOSYS
+ */
+#define MC_CMD_WOL_FILTER_RESET 0x34
+#define MC_CMD_WOL_FILTER_RESET_IN_LEN 0
+#define MC_CMD_WOL_FILTER_RESET_OUT_LEN 0
+
+/* MC_CMD_SET_MCAST_HASH:
+ * Set the MCASH hash value without otherwise
+ * reconfiguring the MAC
+ */
+#define MC_CMD_SET_MCAST_HASH 0x35
+#define MC_CMD_SET_MCAST_HASH_IN_LEN 32
+#define MC_CMD_SET_MCAST_HASH_IN_HASH0_OFST 0
+#define MC_CMD_SET_MCAST_HASH_IN_HASH1_OFST 16
+#define MC_CMD_SET_MCAST_HASH_OUT_LEN 0
+
+/* MC_CMD_NVRAM_TYPES:
+ * Return bitfield indicating available types of virtual NVRAM partitions
+ *
+ * Locks required: none
+ * Returns: 0
+ */
+#define MC_CMD_NVRAM_TYPES 0x36
+#define MC_CMD_NVRAM_TYPES_IN_LEN 0
+#define MC_CMD_NVRAM_TYPES_OUT_LEN 4
+#define MC_CMD_NVRAM_TYPES_OUT_TYPES_OFST 0
+
+/* Supported NVRAM types */
+#define MC_CMD_NVRAM_TYPE_DISABLED_CALLISTO 0
+#define MC_CMD_NVRAM_TYPE_MC_FW 1
+#define MC_CMD_NVRAM_TYPE_MC_FW_BACKUP 2
+#define MC_CMD_NVRAM_TYPE_STATIC_CFG_PORT0 3
+#define MC_CMD_NVRAM_TYPE_STATIC_CFG_PORT1 4
+#define MC_CMD_NVRAM_TYPE_DYNAMIC_CFG_PORT0 5
+#define MC_CMD_NVRAM_TYPE_DYNAMIC_CFG_PORT1 6
+#define MC_CMD_NVRAM_TYPE_EXP_ROM 7
+#define MC_CMD_NVRAM_TYPE_EXP_ROM_CFG_PORT0 8
+#define MC_CMD_NVRAM_TYPE_EXP_ROM_CFG_PORT1 9
+#define MC_CMD_NVRAM_TYPE_PHY_PORT0 10
+#define MC_CMD_NVRAM_TYPE_PHY_PORT1 11
+#define MC_CMD_NVRAM_TYPE_LOG 12
+
+/* MC_CMD_NVRAM_INFO:
+ * Read info about a virtual NVRAM partition
+ *
+ * Locks required: none
+ * Returns: 0, EINVAL (bad type)
+ */
+#define MC_CMD_NVRAM_INFO 0x37
+#define MC_CMD_NVRAM_INFO_IN_LEN 4
+#define MC_CMD_NVRAM_INFO_IN_TYPE_OFST 0
+#define MC_CMD_NVRAM_INFO_OUT_LEN 24
+#define MC_CMD_NVRAM_INFO_OUT_TYPE_OFST 0
+#define MC_CMD_NVRAM_INFO_OUT_SIZE_OFST 4
+#define MC_CMD_NVRAM_INFO_OUT_ERASESIZE_OFST 8
+#define MC_CMD_NVRAM_INFO_OUT_FLAGS_OFST 12
+#define   MC_CMD_NVRAM_PROTECTED_LBN 0
+#define   MC_CMD_NVRAM_PROTECTED_WIDTH 1
+#define MC_CMD_NVRAM_INFO_OUT_PHYSDEV_OFST 16
+#define MC_CMD_NVRAM_INFO_OUT_PHYSADDR_OFST 20
+
+/* MC_CMD_NVRAM_UPDATE_START:
+ * Start a group of update operations on a virtual NVRAM partition
+ *
+ * Locks required: PHY_LOCK if type==*PHY*
+ * Returns: 0, EINVAL (bad type), EACCES (if PHY_LOCK required and not held)
+ */
+#define MC_CMD_NVRAM_UPDATE_START 0x38
+#define MC_CMD_NVRAM_UPDATE_START_IN_LEN 4
+#define MC_CMD_NVRAM_UPDATE_START_IN_TYPE_OFST 0
+#define MC_CMD_NVRAM_UPDATE_START_OUT_LEN 0
+
+/* MC_CMD_NVRAM_READ:
+ * Read data from a virtual NVRAM partition
+ *
+ * Locks required: PHY_LOCK if type==*PHY*
+ * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held)
+ */
+#define MC_CMD_NVRAM_READ 0x39
+#define MC_CMD_NVRAM_READ_IN_LEN 12
+#define MC_CMD_NVRAM_READ_IN_TYPE_OFST 0
+#define MC_CMD_NVRAM_READ_IN_OFFSET_OFST 4
+#define MC_CMD_NVRAM_READ_IN_LENGTH_OFST 8
+#define MC_CMD_NVRAM_READ_OUT_LEN(_read_bytes) (_read_bytes)
+#define MC_CMD_NVRAM_READ_OUT_READ_BUFFER_OFST 0
+
+/* MC_CMD_NVRAM_WRITE:
+ * Write data to a virtual NVRAM partition
+ *
+ * Locks required: PHY_LOCK if type==*PHY*
+ * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held)
+ */
+#define MC_CMD_NVRAM_WRITE 0x3a
+#define MC_CMD_NVRAM_WRITE_IN_TYPE_OFST 0
+#define MC_CMD_NVRAM_WRITE_IN_OFFSET_OFST 4
+#define MC_CMD_NVRAM_WRITE_IN_LENGTH_OFST 8
+#define MC_CMD_NVRAM_WRITE_IN_WRITE_BUFFER_OFST 12
+#define MC_CMD_NVRAM_WRITE_IN_LEN(_write_bytes) (12 + _write_bytes)
+#define MC_CMD_NVRAM_WRITE_OUT_LEN 0
+
+/* MC_CMD_NVRAM_ERASE:
+ * Erase sector(s) from a virtual NVRAM partition
+ *
+ * Locks required: PHY_LOCK if type==*PHY*
+ * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held)
+ */
+#define MC_CMD_NVRAM_ERASE 0x3b
+#define MC_CMD_NVRAM_ERASE_IN_LEN 12
+#define MC_CMD_NVRAM_ERASE_IN_TYPE_OFST 0
+#define MC_CMD_NVRAM_ERASE_IN_OFFSET_OFST 4
+#define MC_CMD_NVRAM_ERASE_IN_LENGTH_OFST 8
+#define MC_CMD_NVRAM_ERASE_OUT_LEN 0
+
+/* MC_CMD_NVRAM_UPDATE_FINISH:
+ * Finish a group of update operations on a virtual NVRAM partition
+ *
+ * Locks required: PHY_LOCK if type==*PHY*
+ * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held)
+ */
+#define MC_CMD_NVRAM_UPDATE_FINISH 0x3c
+#define MC_CMD_NVRAM_UPDATE_FINISH_IN_LEN 8
+#define MC_CMD_NVRAM_UPDATE_FINISH_IN_TYPE_OFST 0
+#define MC_CMD_NVRAM_UPDATE_FINISH_IN_REBOOT_OFST 4
+#define MC_CMD_NVRAM_UPDATE_FINISH_OUT_LEN 0
+
+/* MC_CMD_REBOOT:
+ * Reboot the MC.
+ *
+ * The AFTER_ASSERTION flag is intended to be used when the driver notices
+ * an assertion failure (at which point it is expected to perform a complete
+ * tear down and reinitialise), to allow both ports to reset the MC once
+ * in an atomic fashion.
+ *
+ * Production mc firmwares are generally compiled with REBOOT_ON_ASSERT=1,
+ * which means that they will automatically reboot out of the assertion
+ * handler, so this is in practise an optional operation. It is still
+ * recommended that drivers execute this to support custom firmwares
+ * with REBOOT_ON_ASSERT=0.
+ *
+ * Locks required: NONE
+ * Returns: Nothing. You get back a response with ERR=1, DATALEN=0
+ */
+#define MC_CMD_REBOOT 0x3d
+#define MC_CMD_REBOOT_IN_LEN 4
+#define MC_CMD_REBOOT_IN_FLAGS_OFST 0
+#define MC_CMD_REBOOT_FLAGS_AFTER_ASSERTION 1
+#define MC_CMD_REBOOT_OUT_LEN 0
+
+/* MC_CMD_SCHEDINFO:
+ * Request scheduler info. from the MC.
+ *
+ * Locks required: NONE
+ * Returns: An array of (timeslice,maximum overrun), one for each thread,
+ * in ascending order of thread address.s
+ */
+#define MC_CMD_SCHEDINFO 0x3e
+#define MC_CMD_SCHEDINFO_IN_LEN 0
+
+
+/* MC_CMD_SET_REBOOT_MODE: (debug)
+ * Set the mode for the next MC reboot.
+ *
+ * Locks required: NONE
+ *
+ * Sets the reboot mode to the specified value.  Returns the old mode.
+ */
+#define MC_CMD_REBOOT_MODE 0x3f
+#define MC_CMD_REBOOT_MODE_IN_LEN 4
+#define MC_CMD_REBOOT_MODE_IN_VALUE_OFST 0
+#define MC_CMD_REBOOT_MODE_OUT_LEN 4
+#define MC_CMD_REBOOT_MODE_OUT_VALUE_OFST 0
+#define   MC_CMD_REBOOT_MODE_NORMAL 0
+#define   MC_CMD_REBOOT_MODE_SNAPPER 3
+
+/* MC_CMD_DEBUG_LOG:
+ * Null request/response command (debug)
+ * - sequence number is always zero
+ * - only supported on the UART interface
+ * (the same set of bytes is delivered as an
+ * event over PCI)
+ */
+#define MC_CMD_DEBUG_LOG 0x40
+#define MC_CMD_DEBUG_LOG_IN_LEN 0
+#define MC_CMD_DEBUG_LOG_OUT_LEN 0
+
+/* Generic sensor enumeration. Note that a dual port NIC
+ * will EITHER expose PHY_COMMON_TEMP OR PHY0_TEMP and
+ * PHY1_TEMP depending on whether there is a single sensor
+ * in the vicinity of the two port, or one per port.
+ */
+#define MC_CMD_SENSOR_CONTROLLER_TEMP 0         /* degC */
+#define MC_CMD_SENSOR_PHY_COMMON_TEMP 1         /* degC */
+#define MC_CMD_SENSOR_CONTROLLER_COOLING 2      /* bool */
+#define MC_CMD_SENSOR_PHY0_TEMP 3               /* degC */
+#define MC_CMD_SENSOR_PHY0_COOLING 4            /* bool */
+#define MC_CMD_SENSOR_PHY1_TEMP 5               /* degC */
+#define MC_CMD_SENSOR_PHY1_COOLING 6            /* bool */
+#define MC_CMD_SENSOR_IN_1V0 7                  /* mV */
+#define MC_CMD_SENSOR_IN_1V2 8                  /* mV */
+#define MC_CMD_SENSOR_IN_1V8 9                  /* mV */
+#define MC_CMD_SENSOR_IN_2V5 10                 /* mV */
+#define MC_CMD_SENSOR_IN_3V3 11                 /* mV */
+#define MC_CMD_SENSOR_IN_12V0 12                /* mV */
+
+
+/* Sensor state */
+#define MC_CMD_SENSOR_STATE_OK 0
+#define MC_CMD_SENSOR_STATE_WARNING 1
+#define MC_CMD_SENSOR_STATE_FATAL 2
+#define MC_CMD_SENSOR_STATE_BROKEN 3
+
+/* MC_CMD_SENSOR_INFO:
+ * Returns information about every available sensor.
+ *
+ * Each sensor has a single (16bit) value, and a corresponding state.
+ * The mapping between value and sensor is nominally determined by the
+ * MC, but in practise is implemented as zero (BROKEN), one (TEMPERATURE),
+ * or two (VOLTAGE) ranges per sensor per state.
+ *
+ * This call returns a mask (32bit) of the sensors that are supported
+ * by this platform, then an array (indexed by MC_CMD_SENSOR) of byte
+ * offsets to the per-sensor arrays. Each sensor array has four 16bit
+ * numbers, min1, max1, min2, max2.
+ *
+ * Locks required: None
+ * Returns: 0
+ */
+#define MC_CMD_SENSOR_INFO 0x41
+#define MC_CMD_SENSOR_INFO_IN_LEN 0
+#define MC_CMD_SENSOR_INFO_OUT_MASK_OFST 0
+#define MC_CMD_SENSOR_INFO_OUT_OFFSET_OFST(_x) \
+        (4 + (_x))
+#define MC_CMD_SENSOR_INFO_OUT_MIN1_OFST(_ofst) \
+        ((_ofst) + 0)
+#define MC_CMD_SENSOR_INFO_OUT_MAX1_OFST(_ofst) \
+        ((_ofst) + 2)
+#define MC_CMD_SENSOR_INFO_OUT_MIN2_OFST(_ofst) \
+        ((_ofst) + 4)
+#define MC_CMD_SENSOR_INFO_OUT_MAX2_OFST(_ofst) \
+        ((_ofst) + 6)
+
+/* MC_CMD_READ_SENSORS
+ * Returns the current reading from each sensor
+ *
+ * Returns a sparse array of sensor readings (indexed by the sensor
+ * type) into host memory.  Each array element is a dword.
+ *
+ * The MC will send a SENSOREVT event every time any sensor changes state. The
+ * driver is responsible for ensuring that it doesn't miss any events. The board
+ * will function normally if all sensors are in STATE_OK or state_WARNING.
+ * Otherwise the board should not be expected to function.
+ */
+#define MC_CMD_READ_SENSORS 0x42
+#define MC_CMD_READ_SENSORS_IN_LEN 8
+#define MC_CMD_READ_SENSORS_IN_DMA_ADDR_LO_OFST 0
+#define MC_CMD_READ_SENSORS_IN_DMA_ADDR_HI_OFST 4
+#define MC_CMD_READ_SENSORS_OUT_LEN 0
+
+/* Sensor reading fields */
+#define MC_CMD_READ_SENSOR_VALUE_LBN 0
+#define MC_CMD_READ_SENSOR_VALUE_WIDTH 16
+#define MC_CMD_READ_SENSOR_STATE_LBN 16
+#define MC_CMD_READ_SENSOR_STATE_WIDTH 8
+
+
+/* MC_CMD_GET_PHY_STATE:
+ * Report current state of PHY.  A "zombie" PHY is a PHY that has failed to
+ * boot (e.g. due to missing or corrupted firmware).
+ *
+ * Locks required: None
+ * Return code: 0
+ */
+#define MC_CMD_GET_PHY_STATE 0x43
+
+#define MC_CMD_GET_PHY_STATE_IN_LEN 0
+#define MC_CMD_GET_PHY_STATE_OUT_LEN 4
+#define MC_CMD_GET_PHY_STATE_STATE_OFST 0
+/* PHY state enumeration: */
+#define MC_CMD_PHY_STATE_OK 1
+#define MC_CMD_PHY_STATE_ZOMBIE 2
+
+
+/* 802.1Qbb control. 8 Tx queues that map to priorities 0 - 7. Use all 1s to
+ * disable 802.Qbb for a given priority. */
+#define MC_CMD_SETUP_8021QBB 0x44
+#define MC_CMD_SETUP_8021QBB_IN_LEN 32
+#define MC_CMD_SETUP_8021QBB_OUT_LEN 0
+#define MC_CMD_SETUP_8021QBB_IN_TXQS_OFFST 0
+
+
+/* MC_CMD_WOL_FILTER_GET:
+ * Retrieve ID of any WoL filters
+ *
+ * Locks required: None
+ * Returns: 0, ENOSYS
+ */
+#define MC_CMD_WOL_FILTER_GET 0x45
+#define MC_CMD_WOL_FILTER_GET_IN_LEN 0
+#define MC_CMD_WOL_FILTER_GET_OUT_LEN 4
+#define MC_CMD_WOL_FILTER_GET_OUT_FILTER_ID_OFST 0
+
+
+/* MC_CMD_ADD_LIGHTSOUT_OFFLOAD:
+ * Offload a protocol to NIC for lights-out state
+ *
+ * Locks required: None
+ * Returns: 0, ENOSYS
+ */
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD 0x46
+
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_LEN 16
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_PROTOCOL_OFST 0
+
+/* There is a union at offset 4, following defines overlap due to
+ * this */
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_DATA_OFST 4
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_ARPMAC_OFST 4
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_ARPIP_OFST 10
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_NSMAC_OFST 4
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_NSSNIPV6_OFST 10
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_NSIPV6_OFST 26
+
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_OUT_LEN 4
+#define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_OUT_FILTER_ID_OFST 0
+
+
+/* MC_CMD_REMOVE_LIGHTSOUT_PROTOCOL_OFFLOAD:
+ * Offload a protocol to NIC for lights-out state
+ *
+ * Locks required: None
+ * Returns: 0, ENOSYS
+ */
+#define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD 0x47
+#define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_IN_LEN 8
+#define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_OUT_LEN 0
+
+#define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_IN_PROTOCOL_OFST 0
+#define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_IN_FILTER_ID_OFST 4
+
+/* Lights-out offload protocols enumeration */
+#define MC_CMD_LIGHTSOUT_OFFLOAD_PROTOCOL_ARP 0x1
+#define MC_CMD_LIGHTSOUT_OFFLOAD_PROTOCOL_NS  0x2
+
+
+/* MC_CMD_MAC_RESET_RESTORE:
+ * Restore MAC after block reset
+ *
+ * Locks required: None
+ * Returns: 0
+ */
+
+#define MC_CMD_MAC_RESET_RESTORE 0x48
+#define MC_CMD_MAC_RESET_RESTORE_IN_LEN 0
+#define MC_CMD_MAC_RESET_RESTORE_OUT_LEN 0
+
+
+/* MC_CMD_TEST_ASSERT:
+ * Deliberately trigger an assert-detonation in the firmware for testing
+ * purposes (i.e. to allow tests that the driver copes gracefully).
+ *
+ * Locks required: None
+ * Returns: 0
+ */
+
+#define MC_CMD_TESTASSERT 0x49
+#define MC_CMD_TESTASSERT_IN_LEN 0
+#define MC_CMD_TESTASSERT_OUT_LEN 0
+
+/* MC_CMD_WORKAROUND 0x4a
+ *
+ * Enable/Disable a given workaround. The mcfw will return EINVAL if it
+ * doesn't understand the given workaround number - which should not
+ * be treated as a hard error by client code.
+ *
+ * This op does not imply any semantics about each workaround, that's between
+ * the driver and the mcfw on a per-workaround basis.
+ *
+ * Locks required: None
+ * Returns: 0, EINVAL
+ */
+#define MC_CMD_WORKAROUND 0x4a
+#define MC_CMD_WORKAROUND_IN_LEN 8
+#define MC_CMD_WORKAROUND_IN_TYPE_OFST 0
+#define MC_CMD_WORKAROUND_BUG17230 1
+#define MC_CMD_WORKAROUND_IN_ENABLED_OFST 4
+#define MC_CMD_WORKAROUND_OUT_LEN 0
+
+/* MC_CMD_GET_PHY_MEDIA_INFO:
+ * Read media-specific data from PHY (e.g. SFP/SFP+ module ID information for
+ * SFP+ PHYs).
+ *
+ * The "media type" can be found via GET_PHY_CFG (GET_PHY_CFG_OUT_MEDIA_TYPE);
+ * the valid "page number" input values, and the output data, are interpreted
+ * on a per-type basis.
+ *
+ * For SFP+: PAGE=0 or 1 returns a 128-byte block read from module I2C address
+ *           0xA0 offset 0 or 0x80.
+ * Anything else: currently undefined.
+ *
+ * Locks required: None
+ * Return code: 0
+ */
+#define MC_CMD_GET_PHY_MEDIA_INFO 0x4b
+#define MC_CMD_GET_PHY_MEDIA_INFO_IN_LEN 4
+#define MC_CMD_GET_PHY_MEDIA_INFO_IN_PAGE_OFST 0
+#define MC_CMD_GET_PHY_MEDIA_INFO_OUT_LEN(_num_bytes) (4 + (_num_bytes))
+#define MC_CMD_GET_PHY_MEDIA_INFO_OUT_DATALEN_OFST 0
+#define MC_CMD_GET_PHY_MEDIA_INFO_OUT_DATA_OFST 4
+
+/* MC_CMD_NVRAM_TEST:
+ * Test a particular NVRAM partition for valid contents (where "valid"
+ * depends on the type of partition).
+ *
+ * Locks required: None
+ * Return code: 0
+ */
+#define MC_CMD_NVRAM_TEST 0x4c
+#define MC_CMD_NVRAM_TEST_IN_LEN 4
+#define MC_CMD_NVRAM_TEST_IN_TYPE_OFST 0
+#define MC_CMD_NVRAM_TEST_OUT_LEN 4
+#define MC_CMD_NVRAM_TEST_OUT_RESULT_OFST 0
+#define MC_CMD_NVRAM_TEST_PASS 0
+#define MC_CMD_NVRAM_TEST_FAIL 1
+#define MC_CMD_NVRAM_TEST_NOTSUPP 2
+
+/* MC_CMD_MRSFP_TWEAK: (debug)
+ * Read status and/or set parameters for the "mrsfp" driver in mr_rusty builds.
+ * I2C I/O expander bits are always read; if equaliser parameters are supplied,
+ * they are configured first.
+ *
+ * Locks required: None
+ * Return code: 0, EINVAL
+ */
+#define MC_CMD_MRSFP_TWEAK 0x4d
+#define MC_CMD_MRSFP_TWEAK_IN_LEN_READ_ONLY 0
+#define MC_CMD_MRSFP_TWEAK_IN_LEN_EQ_CONFIG 16
+#define MC_CMD_MRSFP_TWEAK_IN_TXEQ_LEVEL_OFST 0    /* 0-6 low->high de-emph. */
+#define MC_CMD_MRSFP_TWEAK_IN_TXEQ_DT_CFG_OFST 4   /* 0-8 low->high ref.V */
+#define MC_CMD_MRSFP_TWEAK_IN_RXEQ_BOOST_OFST 8    /* 0-8 low->high boost */
+#define MC_CMD_MRSFP_TWEAK_IN_RXEQ_DT_CFG_OFST 12  /* 0-8 low->high ref.V */
+#define MC_CMD_MRSFP_TWEAK_OUT_LEN 12
+#define MC_CMD_MRSFP_TWEAK_OUT_IOEXP_INPUTS_OFST 0     /* input bits */
+#define MC_CMD_MRSFP_TWEAK_OUT_IOEXP_OUTPUTS_OFST 4    /* output bits */
+#define MC_CMD_MRSFP_TWEAK_OUT_IOEXP_DIRECTION_OFST 8  /* dirs: 0=out, 1=in */
+
+/* MC_CMD_TEST_HACK: (debug (unsurprisingly))
+  * Change bits of network port state for test purposes in ways that would never be
+  * useful in normal operation and so need a special command to change. */
+#define MC_CMD_TEST_HACK 0x2f
+#define MC_CMD_TEST_HACK_IN_LEN 8
+#define MC_CMD_TEST_HACK_IN_TXPAD_OFST 0
+#define   MC_CMD_TEST_HACK_IN_TXPAD_AUTO  0 /* Let the MC manage things */
+#define   MC_CMD_TEST_HACK_IN_TXPAD_ON    1 /* Force on */
+#define   MC_CMD_TEST_HACK_IN_TXPAD_OFF   2 /* Force on */
+#define MC_CMD_TEST_HACK_IN_IPG_OFST   4 /* Takes a value in bits */
+#define   MC_CMD_TEST_HACK_IN_IPG_AUTO    0 /* The MC picks the value */
+#define MC_CMD_TEST_HACK_OUT_LEN 0
+
+/* MC_CMD_SENSOR_SET_LIMS: (debug) (mostly) adjust the sensor limits. This
+ * is a warranty-voiding operation.
+  *
+ * IN: sensor identifier (one of the enumeration starting with MC_CMD_SENSOR_CONTROLLER_TEMP
+ * followed by 4 32-bit values: min(warning) max(warning), min(fatal), max(fatal). Which
+ * of these limits are meaningful and what their interpretation is is sensor-specific.
+ *
+ * OUT: nothing
+ *
+ * Returns: ENOENT if the sensor specified does not exist, EINVAL if the limits are
+  * out of range.
+ */
+#define MC_CMD_SENSOR_SET_LIMS 0x4e
+#define MC_CMD_SENSOR_SET_LIMS_IN_LEN 20
+#define MC_CMD_SENSOR_SET_LIMS_IN_SENSOR_OFST 0
+#define MC_CMD_SENSOR_SET_LIMS_IN_LOW0_OFST 4
+#define MC_CMD_SENSOR_SET_LIMS_IN_HI0_OFST  8
+#define MC_CMD_SENSOR_SET_LIMS_IN_LOW1_OFST 12
+#define MC_CMD_SENSOR_SET_LIMS_IN_HI1_OFST  16
+
+/* Do NOT add new commands beyond 0x4f as part of 3.0 : 0x50 - 0x7f will be
+ * used for post-3.0 extensions. If you run out of space, look for gaps or
+ * commands that are unused in the existing range. */
+
+#endif /* MCDI_PCOL_H */