1 files changed, 88 insertions, 0 deletions

diff --git a/drivers/net/ethernet/freescale/Kconfig b/drivers/net/ethernet/freescale/Kconfig
new file mode 100644
index 00000000000..2fd2c614c08
--- /dev/null
+++ b/drivers/net/ethernet/freescale/Kconfig
@@ -0,0 +1,88 @@
+#
+# Freescale device configuration
+#
+
+config NET_VENDOR_FREESCALE
+        bool "Freescale devices"
+        depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
+                   M523x || M527x || M5272 || M528x || M520x || M532x || \
+                   IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC || \
+                   (PPC_MPC52xx && PPC_BESTCOMM)
+        ---help---
+          If you have a network (Ethernet) card belonging to this class, say Y
+          and read the Ethernet-HOWTO, available from
+          <http://www.tldp.org/docs.html#howto>.
+
+          Note that the answer to this question doesn't directly affect the
+          kernel: saying N will just cause the configurator to skip all
+          the questions about IBM devices. If you say Y, you will be asked for
+          your specific card in the following questions.
+
+if NET_VENDOR_FREESCALE
+
+config FEC
+        bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
+        depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
+                    IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC)
+        default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM
+        select PHYLIB
+        ---help---
+          Say Y here if you want to use the built-in 10/100 Fast ethernet
+          controller on some Motorola ColdFire and Freescale i.MX processors.
+
+config FEC_MPC52xx
+        tristate "FEC MPC52xx driver"
+        depends on PPC_MPC52xx && PPC_BESTCOMM
+        select CRC32
+        select PHYLIB
+        select PPC_BESTCOMM_FEC
+        ---help---
+          This option enables support for the MPC5200's on-chip
+          Fast Ethernet Controller
+          If compiled as module, it will be called fec_mpc52xx.
+
+config FEC_MPC52xx_MDIO
+        bool "FEC MPC52xx MDIO bus driver"
+        depends on FEC_MPC52xx
+        default y
+        ---help---
+          The MPC5200's FEC can connect to the Ethernet either with
+          an external MII PHY chip or 10 Mbps 7-wire interface
+          (Motorola? industry standard).
+          If your board uses an external PHY connected to FEC, enable this.
+          If not sure, enable.
+          If compiled as module, it will be called fec_mpc52xx_phy.
+
+source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
+
+config FSL_PQ_MDIO
+        tristate "Freescale PQ MDIO"
+        depends on FSL_SOC
+        select PHYLIB
+        ---help---
+          This driver supports the MDIO bus used by the gianfar and UCC drivers.
+
+config UCC_GETH
+        tristate "Freescale QE Gigabit Ethernet"
+        depends on QUICC_ENGINE
+        select FSL_PQ_MDIO
+        select PHYLIB
+        ---help---
+          This driver supports the Gigabit Ethernet mode of the QUICC Engine,
+          which is available on some Freescale SOCs.
+
+config UGETH_TX_ON_DEMAND
+        bool "Transmit on Demand support"
+        depends on UCC_GETH
+
+config GIANFAR
+        tristate "Gianfar Ethernet"
+        depends on FSL_SOC
+        select FSL_PQ_MDIO
+        select PHYLIB
+        select CRC32
+        ---help---
+          This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
+          and MPC86xx family of chips, and the FEC on the 8540.
+
+endif # NET_VENDOR_FREESCALE