1 files changed, 209 insertions, 0 deletions

diff --git a/drivers/net/chelsio/my3126.c b/drivers/net/chelsio/my3126.c
new file mode 100644
index 00000000000..a683fd3bb62
--- /dev/null
+++ b/drivers/net/chelsio/my3126.c
@@ -0,0 +1,209 @@
+/* $Date: 2005/11/12 02:13:49 $ $RCSfile: my3126.c,v $ $Revision: 1.15 $ */
+#include "cphy.h"
+#include "elmer0.h"
+#include "suni1x10gexp_regs.h"
+
+/* Port Reset */
+static int my3126_reset(struct cphy *cphy, int wait)
+{
+        /*
+         * This can be done through registers.  It is not required since
+         * a full chip reset is used.
+         */
+        return 0;
+}
+
+static int my3126_interrupt_enable(struct cphy *cphy)
+{
+        schedule_delayed_work(&cphy->phy_update, HZ/30);
+        t1_tpi_read(cphy->adapter, A_ELMER0_GPO, &cphy->elmer_gpo);
+        return 0;
+}
+
+static int my3126_interrupt_disable(struct cphy *cphy)
+{
+        cancel_delayed_work_sync(&cphy->phy_update);
+        return 0;
+}
+
+static int my3126_interrupt_clear(struct cphy *cphy)
+{
+        return 0;
+}
+
+#define OFFSET(REG_ADDR)    (REG_ADDR << 2)
+
+static int my3126_interrupt_handler(struct cphy *cphy)
+{
+        u32 val;
+        u16 val16;
+        u16 status;
+        u32 act_count;
+        adapter_t *adapter;
+        adapter = cphy->adapter;
+
+        if (cphy->count == 50) {
+                cphy_mdio_read(cphy, MDIO_MMD_PMAPMD, MDIO_STAT1, &val);
+                val16 = (u16) val;
+                status = cphy->bmsr ^ val16;
+
+                if (status & MDIO_STAT1_LSTATUS)
+                        t1_link_changed(adapter, 0);
+                cphy->bmsr = val16;
+
+                /* We have only enabled link change interrupts so it
+                   must be that
+                 */
+                cphy->count = 0;
+        }
+
+        t1_tpi_write(adapter, OFFSET(SUNI1x10GEXP_REG_MSTAT_CONTROL),
+                SUNI1x10GEXP_BITMSK_MSTAT_SNAP);
+        t1_tpi_read(adapter,
+                OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_1_LOW), &act_count);
+        t1_tpi_read(adapter,
+                OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_33_LOW), &val);
+        act_count += val;
+
+        /* Populate elmer_gpo with the register value */
+        t1_tpi_read(adapter, A_ELMER0_GPO, &val);
+        cphy->elmer_gpo = val;
+
+        if ( (val & (1 << 8)) || (val & (1 << 19)) ||
+             (cphy->act_count == act_count) || cphy->act_on ) {
+                if (is_T2(adapter))
+                        val |= (1 << 9);
+                else if (t1_is_T1B(adapter))
+                        val |= (1 << 20);
+                cphy->act_on = 0;
+        } else {
+                if (is_T2(adapter))
+                        val &= ~(1 << 9);
+                else if (t1_is_T1B(adapter))
+                        val &= ~(1 << 20);
+                cphy->act_on = 1;
+        }
+
+        t1_tpi_write(adapter, A_ELMER0_GPO, val);
+
+        cphy->elmer_gpo = val;
+        cphy->act_count = act_count;
+        cphy->count++;
+
+        return cphy_cause_link_change;
+}
+
+static void my3216_poll(struct work_struct *work)
+{
+        struct cphy *cphy = container_of(work, struct cphy, phy_update.work);
+
+        my3126_interrupt_handler(cphy);
+}
+
+static int my3126_set_loopback(struct cphy *cphy, int on)
+{
+        return 0;
+}
+
+/* To check the activity LED */
+static int my3126_get_link_status(struct cphy *cphy,
+                        int *link_ok, int *speed, int *duplex, int *fc)
+{
+        u32 val;
+        u16 val16;
+        adapter_t *adapter;
+
+        adapter = cphy->adapter;
+        cphy_mdio_read(cphy, MDIO_MMD_PMAPMD, MDIO_STAT1, &val);
+        val16 = (u16) val;
+
+        /* Populate elmer_gpo with the register value */
+        t1_tpi_read(adapter, A_ELMER0_GPO, &val);
+        cphy->elmer_gpo = val;
+
+        *link_ok = (val16 & MDIO_STAT1_LSTATUS);
+
+        if (*link_ok) {
+                /* Turn on the LED. */
+                if (is_T2(adapter))
+                         val &= ~(1 << 8);
+                else if (t1_is_T1B(adapter))
+                         val &= ~(1 << 19);
+        } else {
+                /* Turn off the LED. */
+                if (is_T2(adapter))
+                         val |= (1 << 8);
+                else if (t1_is_T1B(adapter))
+                         val |= (1 << 19);
+        }
+
+        t1_tpi_write(adapter, A_ELMER0_GPO, val);
+        cphy->elmer_gpo = val;
+        *speed = SPEED_10000;
+        *duplex = DUPLEX_FULL;
+
+        /* need to add flow control */
+        if (fc)
+                *fc = PAUSE_RX | PAUSE_TX;
+
+        return 0;
+}
+
+static void my3126_destroy(struct cphy *cphy)
+{
+        kfree(cphy);
+}
+
+static struct cphy_ops my3126_ops = {
+        .destroy                = my3126_destroy,
+        .reset                  = my3126_reset,
+        .interrupt_enable       = my3126_interrupt_enable,
+        .interrupt_disable      = my3126_interrupt_disable,
+        .interrupt_clear        = my3126_interrupt_clear,
+        .interrupt_handler      = my3126_interrupt_handler,
+        .get_link_status        = my3126_get_link_status,
+        .set_loopback           = my3126_set_loopback,
+        .mmds                   = (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
+                                   MDIO_DEVS_PHYXS),
+};
+
+static struct cphy *my3126_phy_create(struct net_device *dev,
+                        int phy_addr, const struct mdio_ops *mdio_ops)
+{
+        struct cphy *cphy = kzalloc(sizeof (*cphy), GFP_KERNEL);
+
+        if (!cphy)
+                return NULL;
+
+        cphy_init(cphy, dev, phy_addr, &my3126_ops, mdio_ops);
+        INIT_DELAYED_WORK(&cphy->phy_update, my3216_poll);
+        cphy->bmsr = 0;
+
+        return cphy;
+}
+
+/* Chip Reset */
+static int my3126_phy_reset(adapter_t * adapter)
+{
+        u32 val;
+
+        t1_tpi_read(adapter, A_ELMER0_GPO, &val);
+        val &= ~4;
+        t1_tpi_write(adapter, A_ELMER0_GPO, val);
+        msleep(100);
+
+        t1_tpi_write(adapter, A_ELMER0_GPO, val | 4);
+        msleep(1000);
+
+        /* Now lets enable the Laser. Delay 100us */
+        t1_tpi_read(adapter, A_ELMER0_GPO, &val);
+        val |= 0x8000;
+        t1_tpi_write(adapter, A_ELMER0_GPO, val);
+        udelay(100);
+        return 0;
+}
+
+const struct gphy t1_my3126_ops = {
+        .create = my3126_phy_create,
+        .reset = my3126_phy_reset
+};