1 files changed, 29 insertions, 0 deletions

diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c
index a398be28496..a51bb9fb3c8 100644
--- a/arch/avr32/boards/atngw100/setup.c
+++ b/arch/avr32/boards/atngw100/setup.c
@@ -9,6 +9,8 @@
  */
 #include <linux/clk.h>
 #include <linux/etherdevice.h>
+#include <linux/irq.h>
+#include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 #include <linux/init.h>
 #include <linux/linkage.h>
@@ -25,6 +27,13 @@
 #include <asm/arch/init.h>
 #include <asm/arch/portmux.h>
 
+/* Oscillator frequencies. These are board-specific */
+unsigned long at32_board_osc_rates[3] = {
+        [0] = 32768,    /* 32.768 kHz on RTC osc */
+        [1] = 20000000, /* 20 MHz on osc0 */
+        [2] = 12000000, /* 12 MHz on osc1 */
+};
+
 /* Initialized by bootloader-specific startup code. */
 struct tag *bootloader_tags __initdata;
 
@@ -140,6 +149,10 @@ static struct platform_device i2c_gpio_device = {
         },
 };
 
+static struct i2c_board_info __initdata i2c_info[] = {
+        /* NOTE:  original ATtiny24 firmware is at address 0x0b */
+};
+
 static int __init atngw100_init(void)
 {
         unsigned        i;
@@ -165,12 +178,28 @@ static int __init atngw100_init(void)
         }
         platform_device_register(&ngw_gpio_leds);
 
+        /* all these i2c/smbus pins should have external pullups for
+         * open-drain sharing among all I2C devices.  SDA and SCL do;
+         * PB28/EXTINT3 doesn't; it should be SMBALERT# (for PMBus),
+         * but it's not available off-board.
+         */
+        at32_select_periph(GPIO_PIN_PB(28), 0, AT32_GPIOF_PULLUP);
         at32_select_gpio(i2c_gpio_data.sda_pin,
                 AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
         at32_select_gpio(i2c_gpio_data.scl_pin,
                 AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
         platform_device_register(&i2c_gpio_device);
+        i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));
 
         return 0;
 }
 postcore_initcall(atngw100_init);
+
+static int __init atngw100_arch_init(void)
+{
+        /* set_irq_type() after the arch_initcall for EIC has run, and
+         * before the I2C subsystem could try using this IRQ.
+         */
+        return set_irq_type(AT32_EXTINT(3), IRQ_TYPE_EDGE_FALLING);
+}
+arch_initcall(atngw100_arch_init);