arm: at91: move platfarm_data to include/linux/platform_data/atmel.h

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

1 files changed, 67 insertions, 0 deletions

diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
index b0f2c56a8ea..dbd6d53cc27 100644
--- a/include/linux/platform_data/atmel.h
+++ b/include/linux/platform_data/atmel.h
@@ -8,6 +8,49 @@
 #define __ATMEL_H__
 
 #include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/usb/atmel_usba_udc.h>
+#include <linux/atmel-mci.h>
+#include <sound/atmel-ac97c.h>
+#include <linux/serial.h>
+#include <linux/platform_data/macb.h>
+
+ /* USB Device */
+struct at91_udc_data {
+        int     vbus_pin;               /* high == host powering us */
+        u8      vbus_active_low;        /* vbus polarity */
+        u8      vbus_polled;            /* Use polling, not interrupt */
+        int     pullup_pin;             /* active == D+ pulled up */
+        u8      pullup_active_low;      /* true == pullup_pin is active low */
+};
+
+ /* Compact Flash */
+struct at91_cf_data {
+        int     irq_pin;                /* I/O IRQ */
+        int     det_pin;                /* Card detect */
+        int     vcc_pin;                /* power switching */
+        int     rst_pin;                /* card reset */
+        u8      chipselect;             /* EBI Chip Select number */
+        u8      flags;
+#define AT91_CF_TRUE_IDE        0x01
+#define AT91_IDE_SWAP_A0_A2     0x02
+};
+
+ /* USB Host */
+#define AT91_MAX_USBH_PORTS     3
+struct at91_usbh_data {
+        int             vbus_pin[AT91_MAX_USBH_PORTS];  /* port power-control pin */
+        int             overcurrent_pin[AT91_MAX_USBH_PORTS];
+        u8              ports;                          /* number of ports on root hub */
+        u8              overcurrent_supported;
+        u8              vbus_pin_active_low[AT91_MAX_USBH_PORTS];
+        u8              overcurrent_status[AT91_MAX_USBH_PORTS];
+        u8              overcurrent_changed[AT91_MAX_USBH_PORTS];
+};
 
  /* NAND / SmartMedia */
 struct atmel_nand_data {
@@ -24,4 +67,28 @@ struct atmel_nand_data {
         unsigned int    num_parts;
 };
 
+ /* Serial */
+struct atmel_uart_data {
+        int                     num;            /* port num */
+        short                   use_dma_tx;     /* use transmit DMA? */
+        short                   use_dma_rx;     /* use receive DMA? */
+        void __iomem            *regs;          /* virt. base address, if any */
+        struct serial_rs485     rs485;          /* rs485 settings */
+};
+
+ /* Touchscreen Controller */
+struct at91_tsadcc_data {
+        unsigned int    adc_clock;
+        u8              pendet_debounce;
+        u8              ts_sample_hold_time;
+};
+
+/* CAN */
+struct at91_can_data {
+        void (*transceiver_switch)(int on);
+};
+
+/* FIXME: this needs a better location, but gets stuff building again */
+extern int at91_suspend_entering_slow_clock(void);
+
 #endif /* __ATMEL_H__ */