[SCSI] aic79xx: Sequencer update

Update sequencer code to Adaptec version 2.0.12-6.3.9.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

1 files changed, 51 insertions, 11 deletions

diff --git a/drivers/scsi/aic7xxx/aic79xx_osm.c b/drivers/scsi/aic7xxx/aic79xx_osm.c
index 1c8f872e2dd..2567e29960b 100644
--- a/drivers/scsi/aic7xxx/aic79xx_osm.c
+++ b/drivers/scsi/aic7xxx/aic79xx_osm.c
@@ -1468,6 +1468,30 @@ ahd_linux_run_command(struct ahd_softc *ahd, struct ahd_linux_device *dev,
         if ((tstate->auto_negotiate & mask) != 0) {
                 scb->flags |= SCB_AUTO_NEGOTIATE;
                 scb->hscb->control |= MK_MESSAGE;
+                } else if (cmd->cmnd[0] == INQUIRY
+                        && (tinfo->curr.offset != 0
+                         || tinfo->curr.width != MSG_EXT_WDTR_BUS_8_BIT
+                         || tinfo->curr.ppr_options != 0)
+                        && (tinfo->curr.ppr_options & MSG_EXT_PPR_IU_REQ)==0) {
+                        /*
+                         * The SCSI spec requires inquiry
+                         * commands to complete without
+                         * reporting unit attention conditions.
+                         * Because of this, an inquiry command
+                         * that occurs just after a device is
+                         * reset will result in a data phase
+                         * with mismatched negotiated rates.
+                         * The core already forces a renegotiation
+                         * for reset events that are visible to
+                         * our controller or that we initiate,
+                         * but a third party device reset or a
+                         * hot-plug insertion can still cause this
+                         * issue.  Therefore, we force a re-negotiation
+                         * for every inquiry command unless we
+                         * are async.
+                         */
+                        scb->flags |= SCB_NEGOTIATE;
+                        scb->hscb->control |= MK_MESSAGE;
         }
 
         if ((dev->flags & (AHD_DEV_Q_TAGGED|AHD_DEV_Q_BASIC)) != 0) {
@@ -2058,6 +2082,7 @@ ahd_linux_queue_recovery_cmd(struct scsi_cmnd *cmd, scb_flag flag)
         int    paused;
         int    wait;
         int    disconnected;
+        int    found;
         ahd_mode_state saved_modes;
         unsigned long flags;
 
@@ -2176,7 +2201,8 @@ ahd_linux_queue_recovery_cmd(struct scsi_cmnd *cmd, scb_flag flag)
         last_phase = ahd_inb(ahd, LASTPHASE);
         saved_scbptr = ahd_get_scbptr(ahd);
         active_scbptr = saved_scbptr;
-        if (disconnected && (ahd_inb(ahd, SEQ_FLAGS) & NOT_IDENTIFIED) == 0) {
+        if (disconnected && ((last_phase != P_BUSFREE) || 
+                             (ahd_inb(ahd, SEQ_FLAGS) & NOT_IDENTIFIED) == 0)) {
                 struct scb *bus_scb;
 
                 bus_scb = ahd_lookup_scb(ahd, active_scbptr);
@@ -2194,28 +2220,41 @@ ahd_linux_queue_recovery_cmd(struct scsi_cmnd *cmd, scb_flag flag)
          * bus or is in the disconnected state.
          */
         saved_scsiid = ahd_inb(ahd, SAVED_SCSIID);
-        if (last_phase != P_BUSFREE
-         && (SCB_GET_TAG(pending_scb) == active_scbptr
+        if (SCB_GET_TAG(pending_scb) == active_scbptr
              || (flag == SCB_DEVICE_RESET
-                 && SCSIID_TARGET(ahd, saved_scsiid) == scmd_id(cmd)))) {
+                 && SCSIID_TARGET(ahd, saved_scsiid) == scmd_id(cmd))) {
 
                 /*
                  * We're active on the bus, so assert ATN
                  * and hope that the target responds.
                  */
                 pending_scb = ahd_lookup_scb(ahd, active_scbptr);
-                pending_scb->flags |= SCB_RECOVERY_SCB|flag;
+                pending_scb->flags |= SCB_RECOVERY_SCB|SCB_DEVICE_RESET;
                 ahd_outb(ahd, MSG_OUT, HOST_MSG);
                 ahd_outb(ahd, SCSISIGO, last_phase|ATNO);
-                scmd_printk(KERN_INFO, cmd, "Device is active, asserting ATN\n");
+                scmd_printk(KERN_INFO, cmd, "BDR message in message buffer\n");
                 wait = TRUE;
+        } else if (last_phase != P_BUSFREE
+                   && ahd_inb(ahd, SCSIPHASE) == 0) {
+                /*
+                 * SCB is not identified, there
+                 * is no pending REQ, and the sequencer
+                 * has not seen a busfree.  Looks like
+                 * a stuck connection waiting to
+                 * go busfree.  Reset the bus.
+                 */
+                found = ahd_reset_channel(ahd, cmd->device->channel + 'A',
+                                          /*Initiate Reset*/TRUE);
+                printf("%s: Issued Channel %c Bus Reset. "
+                       "%d SCBs aborted\n", ahd_name(ahd),
+                       cmd->device->channel + 'A', found);
         } else if (disconnected) {
 
                 /*
                  * Actually re-queue this SCB in an attempt
                  * to select the device before it reconnects.
                  */
-                pending_scb->flags |= SCB_RECOVERY_SCB|SCB_ABORT;
+                pending_scb->flags |= SCB_RECOVERY_SCB|flag;
                 ahd_set_scbptr(ahd, SCB_GET_TAG(pending_scb));
                 pending_scb->hscb->cdb_len = 0;
                 pending_scb->hscb->task_attribute = 0;
@@ -2296,16 +2335,17 @@ done:
                 timer.expires = jiffies + (5 * HZ);
                 timer.function = ahd_linux_sem_timeout;
                 add_timer(&timer);
-                printf("Recovery code sleeping\n");
+                printf("%s: Recovery code sleeping\n", ahd_name(ahd));
                 down(&ahd->platform_data->eh_sem);
-                printf("Recovery code awake\n");
+                printf("%s: Recovery code awake\n", ahd_name(ahd));
                 ret = del_timer_sync(&timer);
                 if (ret == 0) {
-                        printf("Timer Expired\n");
+                        printf("%s: Timer Expired (active %d)\n",
+                               ahd_name(ahd), dev->active);
                         retval = FAILED;
                 }
         }
-                ahd_unlock(ahd, &flags);
+        ahd_unlock(ahd, &flags);
         return (retval);
 }