rt2x00: Enable fallback rates for rt61pci and rt73usb

Explicitly enable the usage of fallback rates for
the transmission of frames with rt61pci and rt73usb hardware.

Note that for txdone reporting, only rt61pci is capable of
reporting the fallback rates, for USB it is not possible
to determine the number of retries. However the device will
use the fallback rates, so it might still help in the performance.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 22 insertions, 0 deletions

diff --git a/drivers/net/wireless/rt2x00/rt61pci.c b/drivers/net/wireless/rt2x00/rt61pci.c
index 243df08ae91..d1270118f7d 100644
--- a/drivers/net/wireless/rt2x00/rt61pci.c
+++ b/drivers/net/wireless/rt2x00/rt61pci.c
@@ -931,6 +931,9 @@ static void rt61pci_config_retry_limit(struct rt2x00_dev *rt2x00dev,
         u32 reg;
 
         rt2x00pci_register_read(rt2x00dev, TXRX_CSR4, &reg);
+        rt2x00_set_field32(&reg, TXRX_CSR4_OFDM_TX_RATE_DOWN, 1);
+        rt2x00_set_field32(&reg, TXRX_CSR4_OFDM_TX_RATE_STEP, 0);
+        rt2x00_set_field32(&reg, TXRX_CSR4_OFDM_TX_FALLBACK_CCK, 0);
         rt2x00_set_field32(&reg, TXRX_CSR4_LONG_RETRY_LIMIT,
                            libconf->conf->long_frame_max_tx_count);
         rt2x00_set_field32(&reg, TXRX_CSR4_SHORT_RETRY_LIMIT,
@@ -2130,6 +2133,13 @@ static void rt61pci_txdone(struct rt2x00_dev *rt2x00dev)
                 }
                 txdesc.retry = rt2x00_get_field32(reg, STA_CSR4_RETRY_COUNT);
 
+                /*
+                 * the frame was retried at least once
+                 * -> hw used fallback rates
+                 */
+                if (txdesc.retry)
+                        __set_bit(TXDONE_FALLBACK, &txdesc.flags);
+
                 rt2x00pci_txdone(entry, &txdesc);
         }
 }
@@ -2587,6 +2597,18 @@ static int rt61pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
                                                    EEPROM_MAC_ADDR_0));
 
         /*
+         * As rt61 has a global fallback table we cannot specify
+         * more then one tx rate per frame but since the hw will
+         * try several rates (based on the fallback table) we should
+         * still initialize max_rates to the maximum number of rates
+         * we are going to try. Otherwise mac80211 will truncate our
+         * reported tx rates and the rc algortihm will end up with
+         * incorrect data.
+         */
+        rt2x00dev->hw->max_rates = 7;
+        rt2x00dev->hw->max_rate_tries = 1;
+
+        /*
          * Initialize hw_mode information.
          */
         spec->supported_bands = SUPPORT_BAND_2GHZ;