atlx: convert to net_device_ops

Convert this driver to network device ops. Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

2 files changed, 33 insertions, 28 deletions

diff --git a/drivers/net/atlx/atl1.c b/drivers/net/atlx/atl1.c
index 611a86ebe16..7a0fb04e348 100644
--- a/drivers/net/atlx/atl1.c
+++ b/drivers/net/atlx/atl1.c
@@ -2880,6 +2880,21 @@ static void atl1_poll_controller(struct net_device *netdev)
 }
 #endif
 
+static const struct net_device_ops atl1_netdev_ops = {
+        .ndo_open               = atl1_open,
+        .ndo_stop               = atl1_close,
+        .ndo_set_multicast_list = atlx_set_multi,
+        .ndo_validate_addr      = eth_validate_addr,
+        .ndo_set_mac_address    = atl1_set_mac,
+        .ndo_change_mtu         = atl1_change_mtu,
+        .ndo_do_ioctl           = atlx_ioctl,
+        .ndo_tx_timeout = atlx_tx_timeout,
+        .ndo_vlan_rx_register   = atlx_vlan_rx_register,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+        .ndo_poll_controller    = atl1_poll_controller,
+#endif
+};
+
 /*
  * atl1_probe - Device Initialization Routine
  * @pdev: PCI device information struct
@@ -2967,20 +2982,9 @@ static int __devinit atl1_probe(struct pci_dev *pdev,
         adapter->mii.phy_id_mask = 0x1f;
         adapter->mii.reg_num_mask = 0x1f;
 
-        netdev->open = &atl1_open;
-        netdev->stop = &atl1_close;
+        netdev->netdev_ops = &atl1_netdev_ops;
         netdev->hard_start_xmit = &atl1_xmit_frame;
-
-        netdev->set_multicast_list = &atlx_set_multi;
-        netdev->set_mac_address = &atl1_set_mac;
-        netdev->change_mtu = &atl1_change_mtu;
-        netdev->do_ioctl = &atlx_ioctl;
-        netdev->tx_timeout = &atlx_tx_timeout;
         netdev->watchdog_timeo = 5 * HZ;
-#ifdef CONFIG_NET_POLL_CONTROLLER
-        netdev->poll_controller = atl1_poll_controller;
-#endif
-        netdev->vlan_rx_register = atlx_vlan_rx_register;
 
         netdev->ethtool_ops = &atl1_ethtool_ops;
         adapter->bd_number = cards_found;
diff --git a/drivers/net/atlx/atl2.c b/drivers/net/atlx/atl2.c
index 60c9e5375ee..688c21e81a8 100644
--- a/drivers/net/atlx/atl2.c
+++ b/drivers/net/atlx/atl2.c
@@ -1311,6 +1311,22 @@ static void atl2_poll_controller(struct net_device *netdev)
 }
 #endif
 
+
+static const struct net_device_ops atl2_netdev_ops = {
+        .ndo_open               = atl2_open,
+        .ndo_stop               = atl2_close,
+        .ndo_set_multicast_list = atl2_set_multi,
+        .ndo_validate_addr      = eth_validate_addr,
+        .ndo_set_mac_address    = atl2_set_mac,
+        .ndo_change_mtu         = atl2_change_mtu,
+        .ndo_do_ioctl           = atl2_ioctl,
+        .ndo_tx_timeout         = atl2_tx_timeout,
+        .ndo_vlan_rx_register   = atl2_vlan_rx_register,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+        .ndo_poll_controller    = atl2_poll_controller,
+#endif
+};
+
 /*
  * atl2_probe - Device Initialization Routine
  * @pdev: PCI device information struct
@@ -1384,25 +1400,10 @@ static int __devinit atl2_probe(struct pci_dev *pdev,
 
         atl2_setup_pcicmd(pdev);
 
-        netdev->open = &atl2_open;
-        netdev->stop = &atl2_close;
         netdev->hard_start_xmit = &atl2_xmit_frame;
-        netdev->set_multicast_list = &atl2_set_multi;
-        netdev->set_mac_address = &atl2_set_mac;
-        netdev->change_mtu = &atl2_change_mtu;
-        netdev->do_ioctl = &atl2_ioctl;
+        netdev->netdev_ops = &atl2_netdev_ops;
         atl2_set_ethtool_ops(netdev);
-
-#ifdef CONFIG_NET_POLL_CONTROLLER
-        netdev->poll_controller = atl2_poll_controller;
-#endif
-#ifdef HAVE_TX_TIMEOUT
-        netdev->tx_timeout = &atl2_tx_timeout;
         netdev->watchdog_timeo = 5 * HZ;
-#endif
-#ifdef NETIF_F_HW_VLAN_TX
-        netdev->vlan_rx_register = atl2_vlan_rx_register;
-#endif
         strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
 
         netdev->mem_start = mmio_start;