OMAP3: Devkit8000: Change lcd power pin

This patch fixes a wrongly used lcd enable pin.

The Devkit8000 uses twl4030_ledA configured as output gpio only for
the lcd enable line. twl4030_gpio.1 is used through the generic
gpio functions while ledA is used via low level twl4030 calls.

This patch removes the low level calls and use the generic gpio functions
for initialization and use of ledA. This patch also fixes a bug where the
lcd would not power down when blanking.

Further this patch fixes an indentation issue. The comment line uses
eight whitespace and is replaced with a hard tab.

gpio_request + gpio_direction_output are replaced with gpio_request_one.
The return value of gpio_request_one is used to set the value of the
gpio to -EINVAL when unsuccessful, so that gpio_is_valid can detect the
unsuccessful request. But already successful requested gpios are not freed.

Reported-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 16 insertions, 11 deletions

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index e906e05bb41..9a2a31e011c 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -115,9 +115,6 @@ static struct omap2_hsmmc_info mmc[] = {
 
 static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 {
-        twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1);
-        twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0);
-
         if (gpio_is_valid(dssdev->reset_gpio))
                 gpio_set_value_cansleep(dssdev->reset_gpio, 1);
         return 0;
@@ -247,6 +244,8 @@ static struct gpio_led gpio_leds[];
 static int devkit8000_twl_gpio_setup(struct device *dev,
                 unsigned gpio, unsigned ngpio)
 {
+        int ret;
+
         omap_mux_init_gpio(29, OMAP_PIN_INPUT);
         /* gpio + 0 is "mmc0_cd" (input/IRQ) */
         mmc[0].gpio_cd = gpio + 0;
@@ -255,17 +254,23 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
         /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
         gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
 
-        /* gpio + 1 is "LCD_PWREN" (out, active high) */
-        devkit8000_lcd_device.reset_gpio = gpio + 1;
-        gpio_request(devkit8000_lcd_device.reset_gpio, "LCD_PWREN");
-        /* Disable until needed */
-        gpio_direction_output(devkit8000_lcd_device.reset_gpio, 0);
+        /* TWL4030_GPIO_MAX + 0 is "LCD_PWREN" (out, active high) */
+        devkit8000_lcd_device.reset_gpio = gpio + TWL4030_GPIO_MAX + 0;
+        ret = gpio_request_one(devkit8000_lcd_device.reset_gpio,
+                        GPIOF_DIR_OUT | GPIOF_INIT_LOW, "LCD_PWREN");
+        if (ret < 0) {
+                devkit8000_lcd_device.reset_gpio = -EINVAL;
+                printk(KERN_ERR "Failed to request GPIO for LCD_PWRN\n");
+        }
 
         /* gpio + 7 is "DVI_PD" (out, active low) */
         devkit8000_dvi_device.reset_gpio = gpio + 7;
-        gpio_request(devkit8000_dvi_device.reset_gpio, "DVI PowerDown");
-        /* Disable until needed */
-        gpio_direction_output(devkit8000_dvi_device.reset_gpio, 0);
+        ret = gpio_request_one(devkit8000_dvi_device.reset_gpio,
+                        GPIOF_DIR_OUT | GPIOF_INIT_LOW, "DVI PowerDown");
+        if (ret < 0) {
+                devkit8000_dvi_device.reset_gpio = -EINVAL;
+                printk(KERN_ERR "Failed to request GPIO for DVI PowerDown\n");
+        }
 
         return 0;
 }