/* linux/arch/arm/mach-exynos4/platsmp.c
*
* Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
* http://www.samsung.com
*
* Cloned from linux/arch/arm/mach-vexpress/platsmp.c
*
* Copyright (C) 2002 ARM Ltd.
* All Rights Reserved
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/jiffies.h>
#include <linux/smp.h>
#include <linux/io.h>
#include <asm/cacheflush.h>
#include <asm/hardware/gic.h>
#include <asm/smp_scu.h>
#include <asm/unified.h>
#include <mach/hardware.h>
#include <mach/regs-clock.h>
#include <mach/regs-pmu.h>
#include <plat/cpu.h>
extern void exynos4_secondary_startup(void);
#define CPU1_BOOT_REG (samsung_rev() == EXYNOS4210_REV_1_1 ? \
S5P_INFORM5 : S5P_VA_SYSRAM)
/*
* control for which core is the next to come out of the secondary
* boot "holding pen"
*/
volatile int __cpuinitdata pen_release = -1;
/*
* Write pen_release in a way that is guaranteed to be visible to all
* observers, irrespective of whether they're taking part in coherency
* or not. This is necessary for the hotplug code to work reliably.
*/
static void write_pen_release(int val)
{
pen_release = val;
smp_wmb();
__cpuc_flush_dcache_area((void *)&pen_release, sizeof(pen_release));
outer_clean_range(__pa(&pen_release), __pa(&pen_release + 1));
}
static void __iomem *scu_base_addr(void)
{
return (void __iomem *)(S5P_VA_SCU);
}
static DEFINE_SPINLOCK(boot_lock);
void __cpuinit platform_secondary_init(unsigned int cpu)
{
/*
* if any interrupts are already enabled for the primary
* core (e.g. timer irq), then they will not have been enabled
* for us: do so
*/
gic_secondary_init(0);
/*
* let the primary processor know we're out of the
* pen, then head off into the C entry point
*/
write_pen_release(-1);
/*
* Synchronise with the boot thread.
*/
spin_lock(&boot_lock);
spin_unlock(&boot_lock);
}
int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
{
unsigned long timeout;
/*
* Set synchronisation state between this boot processor
* and the secondary one
*/
spin_lock(&boot_lock);
/*
* The secondary processor is waiting to be released from
* the holding pen - release it, then wait for it to flag
* that it has been released by resetting pen_release.
*
* Note that "pen_release" is the hardware CPU ID, whereas
* "cpu" is Linux's internal ID.
*/
write_pen_release(cpu_logical_map(cpu));
if (!(__raw_readl(S5P_ARM_CORE1_STATUS) & S5P_CORE_LOCAL_PWR_EN)) {
__raw_writel(S5P_CORE_LOCAL_PWR_EN,
S5P_ARM_CORE1_CONFIGURATION);
timeout = 10;
/* wait max 10 ms until cpu1 is on */
while ((__raw_readl(S5P_ARM_CORE1_STATUS)
& S5P_CORE_LOCAL_PWR_EN) != S5P_CORE_LOCAL_PWR_EN) {
if (timeout-- == 0)
break;
mdelay(1);
}
if (timeout == 0) {
printk(KERN_ERR "cpu1 power enable failed");
spin_unlock(&boot_lock);
return -ETIMEDOUT;
}
}
/*
* Send the secondary CPU a soft interrupt, thereby causing
* the boot monitor to read the system wide flags register,
* and branch to the address found there.
*/
timeout = jiffies + (1 * HZ);
while (time_before(jiffies, timeout)) {
smp_rmb();
__raw_writel(BSYM(virt_to_phys(exynos4_secondary_startup)),
CPU1_BOOT_REG);
gic_raise_softirq(cpumask_of(cpu), 1);
if (pen_release == -1)
break;
udelay(10);
}
/*
* now the secondary core is starting up let it run its
* calibrations, then wait for it to finish
*/
spin_unlock(&boot_lock);
return pen_release != -1 ? -ENOSYS : 0;
}
/*
* Initialise the CPU possible map early - this describes the CPUs
* which may be present or become present in the system.
*/
void __init smp_init_cpus(void)
{
void __iomem *scu_base = scu_base_addr();
unsigned int i, ncores;
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
/* sanity check */
if (ncores > nr_cpu_ids) {
pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
ncores, nr_cpu_ids);
ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
set_cpu_possible(i, true);
set_smp_cross_call(gic_raise_softirq);
}
void __init platform_smp_prepare_cpus(unsigned int max_cpus)
{
scu_enable(scu_base_addr());
/*
* Write the address of secondary startup into the
* system-wide flags register. The boot monitor waits
* until it receives a soft interrupt, and then the
* secondary CPU branches to this address.
*/
__raw_writel(BSYM(virt_to_phys(exynos4_secondary_startup)),
CPU1_BOOT_REG);
}
