1 files changed, 98 insertions, 0 deletions

diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index 4cab0522d7c..da9bcb89899 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -37,6 +37,103 @@ static int slot1_cover_open;
 static int slot2_cover_open;
 static struct device *mmc_device;
 
+#define TUSB6010_ASYNC_CS       1
+#define TUSB6010_SYNC_CS        4
+#define TUSB6010_GPIO_INT       58
+#define TUSB6010_GPIO_ENABLE    0
+#define TUSB6010_DMACHAN        0x3f
+
+#if defined(CONFIG_USB_TUSB6010) || \
+        defined(CONFIG_USB_TUSB6010_MODULE)
+/*
+ * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
+ * 1.5 V voltage regulators of PM companion chip. Companion chip will then
+ * provide then PGOOD signal to TUSB6010 which will release it from reset.
+ */
+static int tusb_set_power(int state)
+{
+        int i, retval = 0;
+
+        if (state) {
+                gpio_set_value(TUSB6010_GPIO_ENABLE, 1);
+                msleep(1);
+
+                /* Wait until TUSB6010 pulls INT pin down */
+                i = 100;
+                while (i && gpio_get_value(TUSB6010_GPIO_INT)) {
+                        msleep(1);
+                        i--;
+                }
+
+                if (!i) {
+                        printk(KERN_ERR "tusb: powerup failed\n");
+                        retval = -ENODEV;
+                }
+        } else {
+                gpio_set_value(TUSB6010_GPIO_ENABLE, 0);
+                msleep(10);
+        }
+
+        return retval;
+}
+
+static struct musb_hdrc_config musb_config = {
+        .multipoint     = 1,
+        .dyn_fifo       = 1,
+        .num_eps        = 16,
+        .ram_bits       = 12,
+};
+
+static struct musb_hdrc_platform_data tusb_data = {
+#if defined(CONFIG_USB_MUSB_OTG)
+        .mode           = MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
+        .mode           = MUSB_PERIPHERAL,
+#else /* defined(CONFIG_USB_MUSB_HOST) */
+        .mode           = MUSB_HOST,
+#endif
+        .set_power      = tusb_set_power,
+        .min_power      = 25,   /* x2 = 50 mA drawn from VBUS as peripheral */
+        .power          = 100,  /* Max 100 mA VBUS for host mode */
+        .config         = &musb_config,
+};
+
+static void __init n8x0_usb_init(void)
+{
+        int ret = 0;
+        static char     announce[] __initdata = KERN_INFO "TUSB 6010\n";
+
+        /* PM companion chip power control pin */
+        ret = gpio_request(TUSB6010_GPIO_ENABLE, "TUSB6010 enable");
+        if (ret != 0) {
+                printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
+                       TUSB6010_GPIO_ENABLE);
+                return;
+        }
+        gpio_direction_output(TUSB6010_GPIO_ENABLE, 0);
+
+        tusb_set_power(0);
+
+        ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
+                                        TUSB6010_ASYNC_CS, TUSB6010_SYNC_CS,
+                                        TUSB6010_GPIO_INT, TUSB6010_DMACHAN);
+        if (ret != 0)
+                goto err;
+
+        printk(announce);
+
+        return;
+
+err:
+        gpio_free(TUSB6010_GPIO_ENABLE);
+}
+#else
+
+static void __init n8x0_usb_init(void) {}
+
+#endif /*CONFIG_USB_TUSB6010 */
+
+
 static struct omap2_mcspi_device_config p54spi_mcspi_config = {
         .turbo_mode     = 0,
         .single_channel = 1,
@@ -562,6 +659,7 @@ static void __init n8x0_init_machine(void)
         n8x0_menelaus_init();
         n8x0_onenand_init();
         n8x0_mmc_init();
+        n8x0_usb_init();
 }
 
 MACHINE_START(NOKIA_N800, "Nokia N800")