Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 191 insertions, 0 deletions

diff --git a/drivers/net/hamradio/Kconfig b/drivers/net/hamradio/Kconfig
new file mode 100644
index 00000000000..34068f81d45
--- /dev/null
+++ b/drivers/net/hamradio/Kconfig
@@ -0,0 +1,191 @@
+config MKISS
+        tristate "Serial port KISS driver"
+        depends on AX25 && BROKEN_ON_SMP
+        ---help---
+          KISS is a protocol used for the exchange of data between a computer
+          and a Terminal Node Controller (a small embedded system commonly
+          used for networking over AX.25 amateur radio connections; it
+          connects the computer's serial port with the radio's microphone
+          input and speaker output).
+
+          Although KISS is less advanced than the 6pack protocol, it has
+          the advantage that it is already supported by most modern TNCs
+          without the need for a firmware upgrade.
+
+          To compile this driver as a module, choose M here: the module
+          will be called mkiss.
+
+config 6PACK
+        tristate "Serial port 6PACK driver"
+        depends on AX25 && BROKEN_ON_SMP
+        ---help---
+          6pack is a transmission protocol for the data exchange between your
+          PC and your TNC (the Terminal Node Controller acts as a kind of
+          modem connecting your computer's serial port to your radio's
+          microphone input and speaker output). This protocol can be used as
+          an alternative to KISS for networking over AX.25 amateur radio
+          connections, but it has some extended functionality.
+
+          Note that this driver is still experimental and might cause
+          problems. For details about the features and the usage of the
+          driver, read <file:Documentation/networking/6pack.txt>.
+
+          To compile this driver as a module, choose M here: the module
+          will be called 6pack.
+
+config BPQETHER
+        tristate "BPQ Ethernet driver"
+        depends on AX25
+        help
+          AX.25 is the protocol used for computer communication over amateur
+          radio. If you say Y here, you will be able to send and receive AX.25
+          traffic over Ethernet (also called "BPQ AX.25"), which could be
+          useful if some other computer on your local network has a direct
+          amateur radio connection.
+
+config DMASCC
+        tristate "High-speed (DMA) SCC driver for AX.25"
+        depends on ISA && AX25 && BROKEN_ON_SMP
+        ---help---
+          This is a driver for high-speed SCC boards, i.e. those supporting
+          DMA on one port. You usually use those boards to connect your
+          computer to an amateur radio modem (such as the WA4DSY 56kbps
+          modem), in order to send and receive AX.25 packet radio network
+          traffic.
+
+          Currently, this driver supports Ottawa PI/PI2, Paccomm/Gracilis
+          PackeTwin, and S5SCC/DMA boards. They are detected automatically.
+          If you have one of these cards, say Y here and read the AX25-HOWTO,
+          available from <http://www.tldp.org/docs.html#howto>.
+
+          This driver can operate multiple boards simultaneously. If you
+          compile it as a module (by saying M instead of Y), it will be called
+          dmascc. If you don't pass any parameter to the driver, all
+          possible I/O addresses are probed. This could irritate other devices
+          that are currently not in use. You may specify the list of addresses
+          to be probed by "dmascc=addr1,addr2,..." (when compiled into the
+          kernel image) or "io=addr1,addr2,..." (when loaded as a module). The
+          network interfaces will be called dmascc0 and dmascc1 for the board
+          detected first, dmascc2 and dmascc3 for the second one, and so on.
+
+          Before you configure each interface with ifconfig, you MUST set
+          certain parameters, such as channel access timing, clock mode, and
+          DMA channel. This is accomplished with a small utility program,
+          dmascc_cfg, available at
+          <http://cacofonix.nt.tuwien.ac.at/~oe1kib/Linux/>. Please be sure to
+          get at least version 1.27 of dmascc_cfg, as older versions will not
+          work with the current driver.
+
+config SCC
+        tristate "Z8530 SCC driver"
+        depends on ISA && AX25
+        ---help---
+          These cards are used to connect your Linux box to an amateur radio
+          in order to communicate with other computers. If you want to use
+          this, read <file:Documentation/networking/z8530drv.txt> and the
+          AX25-HOWTO, available from
+          <http://www.tldp.org/docs.html#howto>. Also make sure to say Y
+          to "Amateur Radio AX.25 Level 2" support.
+
+          To compile this driver as a module, choose M here: the module
+          will be called scc.
+
+config SCC_DELAY
+        bool "additional delay for PA0HZP OptoSCC compatible boards"
+        depends on SCC
+        help
+          Say Y here if you experience problems with the SCC driver not
+          working properly; please read
+          <file:Documentation/networking/z8530drv.txt> for details.
+
+          If unsure, say N.
+
+config SCC_TRXECHO
+        bool "support for TRX that feedback the tx signal to rx"
+        depends on SCC
+        help
+          Some transmitters feed the transmitted signal back to the receive
+          line.  Say Y here to foil this by explicitly disabling the receiver
+          during data transmission.
+
+          If in doubt, say Y.
+
+config BAYCOM_SER_FDX
+        tristate "BAYCOM ser12 fullduplex driver for AX.25"
+        depends on AX25
+        select CRC_CCITT
+        ---help---
+          This is one of two drivers for Baycom style simple amateur radio
+          modems that connect to a serial interface. The driver supports the
+          ser12 design in full-duplex mode. In addition, it allows the
+          baudrate to be set between 300 and 4800 baud (however not all modems
+          support all baudrates). This is the preferred driver. The next
+          driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
+          driver and still provided in case this driver does not work with
+          your serial interface chip. To configure the driver, use the sethdlc
+          utility available in the standard ax25 utilities package. For
+          information on the modems, see <http://www.baycom.de/> and
+          <file:Documentation/networking/baycom.txt>.
+
+          To compile this driver as a module, choose M here: the module
+          will be called baycom_ser_fdx.  This is recommended.
+
+config BAYCOM_SER_HDX
+        tristate "BAYCOM ser12 halfduplex driver for AX.25"
+        depends on AX25
+        select CRC_CCITT
+        ---help---
+          This is one of two drivers for Baycom style simple amateur radio
+          modems that connect to a serial interface. The driver supports the
+          ser12 design in full-duplex mode. This is the old driver.  It is
+          still provided in case your serial interface chip does not work with
+          the full-duplex driver. This driver is depreciated.  To configure
+          the driver, use the sethdlc utility available in the standard ax25
+          utilities package. For information on the modems, see
+          <http://www.baycom.de/> and
+          <file:Documentation/networking/baycom.txt>.
+
+          To compile this driver as a module, choose M here: the module
+          will be called baycom_ser_hdx.  This is recommended.
+
+config BAYCOM_PAR
+        tristate "BAYCOM picpar and par96 driver for AX.25"
+        depends on PARPORT && AX25
+        select CRC_CCITT
+        ---help---
+          This is a driver for Baycom style simple amateur radio modems that
+          connect to a parallel interface. The driver supports the picpar and
+          par96 designs. To configure the driver, use the sethdlc utility
+          available in the standard ax25 utilities package. For information on
+          the modems, see <http://www.baycom.de/> and the file
+          <file:Documentation/networking/baycom.txt>.
+
+          To compile this driver as a module, choose M here: the module
+          will be called baycom_par.  This is recommended.
+
+config BAYCOM_EPP
+        tristate "BAYCOM epp driver for AX.25"
+        depends on PARPORT && AX25 && !64BIT
+        select CRC_CCITT
+        ---help---
+          This is a driver for Baycom style simple amateur radio modems that
+          connect to a parallel interface. The driver supports the EPP
+          designs. To configure the driver, use the sethdlc utility available
+          in the standard ax25 utilities package. For information on the
+          modems, see <http://www.baycom.de/> and the file
+          <file:Documentation/networking/baycom.txt>.
+
+          To compile this driver as a module, choose M here: the module
+          will be called baycom_epp.  This is recommended.
+
+config YAM
+        tristate "YAM driver for AX.25"
+        depends on AX25
+        help
+          The YAM is a modem for packet radio which connects to the serial
+          port and includes some of the functions of a Terminal Node
+          Controller. If you have one of those, say Y here.
+
+          To compile this driver as a module, choose M here: the module
+          will be called yam.
+