Device tree aware EMAC driver

Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.

This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).

This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 2 insertions, 69 deletions

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 9dc4a80a6ac..cfa97f3fbeb 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1247,75 +1247,8 @@ config IBMVETH
           <file:Documentation/networking/net-modules.txt>. The module will
           be called ibmveth.
 
-config IBM_EMAC
-        tristate "PowerPC 4xx on-chip Ethernet support"
-        depends on 4xx && !PPC_MERGE
-        help
-          This driver supports the PowerPC 4xx EMAC family of on-chip
-          Ethernet controllers.
-
-config IBM_EMAC_RXB
-        int "Number of receive buffers"
-        depends on IBM_EMAC
-        default "128"
-
-config IBM_EMAC_TXB
-        int "Number of transmit buffers"
-        depends on IBM_EMAC
-        default "64"
-
-config IBM_EMAC_POLL_WEIGHT
-        int "MAL NAPI polling weight"
-        depends on IBM_EMAC
-        default "32"
-
-config IBM_EMAC_RX_COPY_THRESHOLD
-        int "RX skb copy threshold (bytes)"
-        depends on IBM_EMAC
-        default "256"
-
-config IBM_EMAC_RX_SKB_HEADROOM
-        int "Additional RX skb headroom (bytes)"
-        depends on IBM_EMAC
-        default "0"
-        help
-          Additional receive skb headroom. Note, that driver
-          will always reserve at least 2 bytes to make IP header
-          aligned, so usually there is no need to add any additional
-          headroom.
-          
-          If unsure, set to 0.
-
-config IBM_EMAC_PHY_RX_CLK_FIX
-        bool "PHY Rx clock workaround"
-        depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
-        help
-          Enable this if EMAC attached to a PHY which doesn't generate
-          RX clock if there is no link, if this is the case, you will 
-          see "TX disable timeout" or "RX disable timeout" in the system
-          log.
-          
-          If unsure, say N.
-
-config IBM_EMAC_DEBUG
-        bool "Debugging"
-        depends on IBM_EMAC
-        default n
-
-config IBM_EMAC_ZMII
-        bool
-        depends on IBM_EMAC && (NP405H || NP405L || 44x)
-        default y
-
-config IBM_EMAC_RGMII
-        bool
-        depends on IBM_EMAC && 440GX
-        default y
-                
-config IBM_EMAC_TAH
-        bool
-        depends on IBM_EMAC && 440GX
-        default y
+source "drivers/net/ibm_emac/Kconfig"
+source "drivers/net/ibm_newemac/Kconfig"
 
 config NET_PCI
         bool "EISA, VLB, PCI and on board controllers"