#
# USB Dual Role (OTG-ready) Controller Drivers
# for silicon based on Mentor Graphics INVENTRA designs
#
comment "Enable Host or Gadget support to see Inventra options"
depends on !USB && USB_GADGET=n
# (M)HDRC = (Multipoint) Highspeed Dual-Role Controller
config USB_MUSB_HDRC
depends on (USB || USB_GADGET) && HAVE_CLK
depends on !SUPERH
select NOP_USB_XCEIV if ARCH_DAVINCI
select TWL4030_USB if MACH_OMAP_3430SDP
select USB_OTG_UTILS
tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)'
help
Say Y here if your system has a dual role high speed USB
controller based on the Mentor Graphics silicon IP. Then
configure options to match your silicon and the board
it's being used with, including the USB peripheral role,
or the USB host role, or both.
Texas Instruments familiies using this IP include DaVinci
(35x, 644x ...), OMAP 243x, OMAP 3, and TUSB 6010.
Analog Devices parts using this IP include Blackfin BF54x,
BF525 and BF527.
If you do not know what this is, please say N.
To compile this driver as a module, choose M here; the
module will be called "musb_hdrc".
config USB_MUSB_SOC
boolean
depends on USB_MUSB_HDRC
default y if ARCH_DAVINCI
default y if ARCH_OMAP2430
default y if ARCH_OMAP34XX
default y if (BF54x && !BF544)
default y if (BF52x && !BF522 && !BF523)
comment "DaVinci 35x and 644x USB support"
depends on USB_MUSB_HDRC && ARCH_DAVINCI
comment "OMAP 243x high speed USB support"
depends on USB_MUSB_HDRC && ARCH_OMAP2430
comment "OMAP 343x high speed USB support"
depends on USB_MUSB_HDRC && ARCH_OMAP34XX
comment "Blackfin high speed USB Support"
depends on USB_MUSB_HDRC && ((BF54x && !BF544) || (BF52x && !BF522 && !BF523))
config USB_TUSB6010
boolean "TUSB 6010 support"
depends on USB_MUSB_HDRC && !USB_MUSB_SOC
select NOP_USB_XCEIV
default y
help
The TUSB 6010 chip, from Texas Instruments, connects a discrete
HDRC core using a 16-bit parallel bus (NOR flash style) or VLYNQ
(a high speed serial link). It can use system-specific external
DMA controllers.
choice
prompt "Driver Mode"
depends on USB_MUSB_HDRC
help
Dual-Role devices can support both host and peripheral roles,
as well as a the special "OTG Device" role which can switch
between both roles as needed.
# use USB_MUSB_HDRC_HCD not USB_MUSB_HOST to #ifdef host side support;
# OTG needs both roles, not just USB_MUSB_HOST.
config USB_MUSB_HOST
depends on USB
bool "USB Host"
help
Say Y here if your system supports the USB host role.
If it has a USB "A" (rectangular), "Mini-A" (uncommon),
or "Mini-AB" connector, it supports the host role.
(With a "Mini-AB" connector, you should enable USB OTG.)
# use USB_GADGET_MUSB_HDRC not USB_MUSB_PERIPHERAL to #ifdef peripheral
# side support ... OTG needs both roles
config USB_MUSB_PERIPHERAL
depends on USB_GADGET
bool "USB Peripheral (gadget stack)"
select USB_GADGET_MUSB_HDRC
help
Say Y here if your system supports the USB peripheral role.
If it has a USB "B" (squarish), "Mini-B", or "Mini-AB"
connector, it supports the peripheral role.
(With a "Mini-AB" connector, you should enable USB OTG.)
config USB_MUSB_OTG
depends on USB && USB_GADGET && PM && EXPERIMENTAL
bool "Both host and peripheral: USB OTG (On The Go) Device"
select USB_GADGET_MUSB_HDRC
select USB_OTG
help
The most notable feature of USB OTG is support for a
"Dual-Role" device, which can act as either a device
or a host. The initial role choice can be changed
later, when two dual-role devices talk to each other.
At this writing, the OTG support in this driver is incomplete,
omitting the mandatory HNP or SRP protocols. However, some
of the cable based role switching works. (That is, grounding
the ID pin switches the controller to host mode, while leaving
it floating leaves it in peripheral mode.)
Select this if your system has a Mini-AB connector, or
to simplify certain kinds of configuration.
To implement your OTG Targeted Peripherals List (TPL), enable
USB_OTG_WHITELIST and update "drivers/usb/core/otg_whitelist.h"
to match your requirements.
endchoice
# enable peripheral support (including with OTG)
config USB_GADGET_MUSB_HDRC
bool
depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG)
# default y
# select USB_GADGET_DUALSPEED
# select USB_GADGET_SELECTED
# enables host support (including with OTG)
config USB_MUSB_HDRC_HCD
bool
depends on USB_MUSB_HDRC && (USB_MUSB_HOST || USB_MUSB_OTG)
select USB_OTG if USB_GADGET_MUSB_HDRC
default y
config MUSB_PIO_ONLY
bool 'Disable DMA (always use PIO)'
depends on USB_MUSB_HDRC
default y if USB_TUSB6010
help
All data is copied between memory and FIFO by the CPU.
DMA controllers are ignored.
Do not select 'n' here unless DMA support for your SOC or board
is unavailable (or unstable). When DMA is enabled at compile time,
you can still disable it at run time using the "use_dma=n" module
parameter.
config USB_INVENTRA_DMA
bool
depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY
default ARCH_OMAP2430 || ARCH_OMAP34XX || BLACKFIN
help
Enable DMA transfers using Mentor's engine.
config USB_TI_CPPI_DMA
bool
depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY
default ARCH_DAVINCI
help
Enable DMA transfers when TI CPPI DMA is available.
config USB_TUSB_OMAP_DMA
bool
depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY
depends on USB_TUSB6010
depends on ARCH_OMAP
default y
help
Enable DMA transfers on TUSB 6010 when OMAP DMA is available.
config USB_MUSB_DEBUG
depends on USB_MUSB_HDRC
bool "Enable debugging messages"
default n
help
This enables musb debugging. To set the logging level use the debug
module parameter. Starting at level 3, per-transfer (urb, usb_request,
packet, or dma transfer) tracing may kick in.
