| Commit message (Collapse) | Author | Age |
|
|
|
|
|
|
|
|
|
| |
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power source of
modules during system suspend and resume procedure. Thus, SAI needs to save
all the values of registers before the system suspend and restore them after
the system resume.
Acked-by: Wang Shengjiu <b02247@freescale.com>
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The SAI mainly has the following clocks:
bus clock
control and configure registers and to generate synchronous
interrupts and DMA requests.
mclk1, mclk2, mclk3
to generate the bit clock when the receiver or transmitter is
configured for an internally generated bit clock.
So this patch adds these clocks and their clock controls to the driver.
[ To concern the old DTB cases, I've added a bit of extra code to make
the driver compatible with them. And by marking clock NULL if failed
to get, the clk_prepare() or clk_get_rate() would easily return 0
so no further path should be broken. -- by Nicolin ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 17d1eb6628e70488c44c46003dcfe583696bb7b7)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The next coming i.MX6 Solo X SoC also contains SAI module while we use
imp_pcm_init() for i.MX platform.
So this patch adds one compatible route for imx6sx and updates the DT
doc accordingly.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 30c35252aadb460e009ca8a3fdc8891903bdfc66)
[ Added essential parameters to imx_pcm_init() calling due to build error,
resulted from the define change of the function on the upstream. ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
We only enable one side interrupt for each stream since over/underrun
on the opposite stream would be resulted from what we previously did,
enabling TERE but remaining FRDE disabled, even though the xrun on the
opposite direction will not break the current stream.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 20ea0d31528f7a461a4ecfb5924ca228bf3ca3c5)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The current trigger() has two crucial problems:
1) The DMA request enabling operations (FSL_SAI_CSR_FRDE) for Tx and Rx are
now totally exclusive: It would fail to run simultaneous Tx-Rx cases.
2) The TERE disabling operation depends on an incorrect condition -- active
reference count that only gets increased in snd_pcm_open() and decreased
in snd_pcm_close(): The TERE would never get cleared.
So this patch overwrites the trigger function by following these rules:
A) We continue to support tx-async-while-rx-sync-to-tx case alone, which's
originally limited by this fsl_sai driver, but we make the code easy to
modify for the further support of the opposite case.
B) We enable both TE and RE for PLAYBACK stream or CAPTURE stream but only
enabling the DMA request bit (FSL_SAI_CSR_FRDE) of the current direction
due to the requirement of SAI -- For tx-async-while-rx-sync-to-tx case,
the receiver is enabled only when both the transmitter and receiver are
enabled.
Tested cases:
a) aplay test.wav -d5
b) arecord -r44100 -c2 -fS16_LE test.wav -d5
c) arecord -r44100 -c2 -fS16_LE -d5 | aplay
d) (aplay test2.wav &); sleep 1; arecord -r44100 -c2 -fS16_LE test.wav -d1
e) (arecord -r44100 -c2 -fS16_LE test.wav -d5 &); sleep 1; aplay test.wav -d1
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit d827786ea623da7ceadaa037f2574a19cbeb90e5)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
It's quite cricial to clear error flags because SAI might hang if getting
FIFO underrun during playback (I haven't confirmed the same issue on Rx
overflow though).
So this patch enables those irq and adds isr() to clear the flags so as to
keep playback entirely safe.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit e2681a1bf5ae053426a6c5c1daaed17b2f95efe6)
|
|
|
|
|
|
|
|
|
|
| |
o Add SND_SOC_DAIFMT_DSP_A support.
o Add SND_SOC_DAIFMT_DSP_B support.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit a3f7dcc9cc0392528bff75b17adfcd74fb8a0ecd)
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
|
|
|
|
|
|
|
| |
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 78957fc349bcf29d415a649601581a993ff25e4d)
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
|
|
This adds Freescale SAI ASoC Audio support.
This implementation is only compatible with device tree definition.
Features:
o Supports playback/capture
o Supports 16/20/24 bit PCM
o Supports 8k - 96k sample rates
o Supports master and slave mode.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 4355082149429d1f87b6fbfc3ebc6305a5372ce2)
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Conflicts:
sound/soc/fsl/Makefile
|