| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
Add a modparam to configure recovery. Recovery
from firmware error is disabled by default to debug
the actual issue further. To recovery from error,
modprobe ath6kl_core recovery_enable=1.
Reported-by: Jin Navy <nhjin@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
| |
|
|
|
|
|
|
|
|
| |
Add a bit in ath6kl_dev_state to maintian the run time state
of firmware recovery configuration. This would help to have
user configuration in fw_recovery which will be added in
a separate patch.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
| |
|
|
|
|
|
|
| |
Checking for recovery state just before re-arming hb_timer is not
necessary, this should be done at the begining of the timer instead.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
| |
|
|
|
|
|
|
|
| |
hb_timer should be scheduled only when hb_poll is non-zero.
But in ath6kl_recovery_work() the timer is scheduled based
on fw_recovery.enable instead which is wrong.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
| |
|
|
|
|
|
|
|
|
| |
In some error conditions, fw pauses HTC pipes which would
result in control endpoint full condition. When we hit this
case, most of the time the device will be unusable. Re-initialize
the target to recover from this situation.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support to detect fw error condition by sending
periodic message (heart beat challenge) to firmware. Upon reception
of the message, fw would send a response event to driver. When
there are no reponses from fw for about 5 cmd driver would
trigger the recovery logic assuming that fw has gone into an
error state.
Capable fw will advertise this capability through
ATH6KL_FW_CAPABILITY_HEART_BEAT_POLL bit. This feature
is disabled by default, can be enabled through a modparam
(heart_beat_poll). This modparam also confiures the polling
interval in msecs.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
|
Re-initialize the target when fw crash is reported.
This would make the device functional again after
target crash. During the target re-initialization
it is made sure that target is not bugged with data/cmd
request, ar->state ATH6KL_STATE_RECOVERY is used
for this purpose.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
