aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/ata
Commit message (Collapse)AuthorAge
* ENGR00284938 sata: cr-rst workaround sata phy link issuesRichard Zhu2014-04-16
| | | | | | | | | | | | | | | | | | | - add sata phy cr(offset:0x7f3f) reset in sata resume to workaround imx6q sata kinds of suspend resume link issues. - add sata phy cr reset during imx6q sata initialization, to initialize the sata phy to be an initialized state. - add about 100us delay between mpll_clk enable and cr-rst, make sure that the mpll_clk is stable. - add about 100us delay between cr-rst and waiting for rx_pll stable too, make sure that the cr-rst is finished. - change the tx level setting from 1.025v to be the default value 1.104v - make sure the sata phy internal pll ref clk enable is cleared before it is set, otherwise, the sata phy link maybe failed when some devices are used. Signed-off-by: Richard Zhu <r65037@freescale.com>
* ENGR00288985 imx: sata: add bus frequency high callbacksRichard Zhu2014-04-16
| | | | | | | Add the fsl BUS_FREQ_HIGH request/release callbacks, during clk enable/disable operations. Signed-off-by: Richard Zhu <r65037@freescale.com>
* ahci: imx: setup power saving methodsRichard Zhu2014-04-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | In order to save power consumption as much as possible. * Disable sata phy internal pll reference clock when sysetem enter into suspend mode, enable it after resume. * Setup module parameter used to enable imx ahci test power down mode(PDDQ) or not, when there is no device detected on the port * minor modifications: - The format of the copyright is changed, because that the original one can't pass fsl internal patch reivew without the character '(c)'. - Exports ahci_platform_ops and ahci_error_handler(). NOTE: * The hot-plug can't be supported when PDDQ mode is ever enabled. * module parameter usage how-to: - default: enable PDDQ mode when no device detected. - add "ahci-imx.hotplug=1" into kernel command line if your don't want to enable PDDQ mode when no device detected on the port. tj: Slightly updated description and comments. Signed-off-by: Richard Zhu <r65037@freescale.com> Signed-off-by: Tejun Heo <tj@kernel.org>
* ahci_imx: add ahci sata support on imx platformsRichard Zhu2014-04-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | imx6q contains one Synopsys AHCI SATA controller, But it can't share ahci_platform driver with other controllers because there are some misalignments of the generic AHCI controller - the bits definitions of the HBA registers, the Vendor Specific registers, the AHCI PHY clock and the AHCI signals adjustment window(GPR13 register). - CAP_SSS(bit20) of the HOST_CAP is writable, default value is '0', should be configured to be '1' - bit0 (only one AHCI SATA port on imx6q) of the HOST_PORTS_IMPL should be set to be '1'.(default 0) - One Vendor Specific register HOST_TIMER1MS(offset:0xe0) should be configured regarding to the frequency of AHB bus clock. - Configurations of the AHCI PHY clock, and the signal parameters of the GPR13 Setup its own ahci sata driver, contained the imx6q specific initialized codes, re-use the generic ahci_platform driver, and keep the generic ahci_platform driver clean as much as possible. tj: patch description reformatted Signed-off-by: Richard Zhu <r65037@freescale.com> Reviewed-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
* libata: disable LPM for some WD SATA-I devicesTejun Heo2014-02-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit ecd75ad514d73efc1bbcc5f10a13566c3ace5f53 upstream. For some reason, some early WD drives spin up and down drives erratically when the link is put into slumber mode which can reduce the life expectancy of the device significantly. Unfortunately, we don't have full list of devices and given the nature of the issue it'd be better to err on the side of false positives than the other way around. Let's disable LPM on all WD devices which match one of the known problematic model prefixes and are SATA-I. As horkage list doesn't support matching SATA capabilities, this is implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is set for the known prefixes and sets the latter if the matched device is SATA-I. Note that this isn't optimal as this disables all LPM operations and partial link power state reportedly works fine on these; however, the way LPM is implemented in libata makes it difficult to precisely map libata LPM setting to specific link power state. Well, these devices are already fairly outdated. Let's just disable whole LPM for now. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com> Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com> References: https://bugzilla.kernel.org/show_bug.cgi?id=57211 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ata: sata_mv: fix disk hotplug for Armada 370/XP SoCsLior Amsalem2014-02-06
| | | | | | | | | | | | | | | | | | | | | | | | | | commit 9013d64e661fc2a37a1742670202171c27fef4b5 upstream. On Armada 370/XP SoCs, once a disk is removed from a SATA port, then the re-plug events are not detected by the sata_mv driver. This patch fixes the issue by updating the PHY speed in the LP_PHY_CTL register (0x58) according to the SControl speed. Note that this fix is only applied if the compatible string "marvell,armada-370-sata" is found in the SATA DT node. Fixes: 9ae6f740b49f ("arm: mach-mvebu: add support for Armada 370 and Armada XP with DT") Signed-off-by: Lior Amsalem <alior@marvell.com> Signed-off-by: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@free-electrons.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ata: sata_mv: introduce compatible string "marvell, armada-370-sata"Simon Guinot2014-02-06
| | | | | | | | | | | | | | | | | | | | | | | commit b1f5c73bd5a4752efb7d7af019034044b08aafe9 upstream. The sata_mv driver supports the SATA IP found in several Marvell SoCs. As some new SATA registers have been introduced with the Armada 370/XP SoCs, a way to identify them is needed. This patch introduces a new compatible string for the SATA IP found in Armada 370/XP SoCs. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@free-electrons.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Lior Amsalem <alior@marvell.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ahci: add PCI ID for Marvell 88SE9170 SATA controllerSimon Guinot2014-01-15
| | | | | | | | | | | | commit e098f5cbe9d410e7878b50f524dce36cc83ec40e upstream. This patch adds support for the PCI ID provided by the Marvell 88SE9170 SATA controller. Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata, freezer: avoid block device removal while system is frozenTejun Heo2014-01-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 85fbd722ad0f5d64d1ad15888cd1eb2188bfb557 upstream. Freezable kthreads and workqueues are fundamentally problematic in that they effectively introduce a big kernel lock widely used in the kernel and have already been the culprit of several deadlock scenarios. This is the latest occurrence. During resume, libata rescans all the ports and revalidates all pre-existing devices. If it determines that a device has gone missing, the device is removed from the system which involves invalidating block device and flushing bdi while holding driver core layer locks. Unfortunately, this can race with the rest of device resume. Because freezable kthreads and workqueues are thawed after device resume is complete and block device removal depends on freezable workqueues and kthreads (e.g. bdi_wq, jbd2) to make progress, this can lead to deadlock - block device removal can't proceed because kthreads are frozen and kthreads can't be thawed because device resume is blocked behind block device removal. 839a8e8660b6 ("writeback: replace custom worker pool implementation with unbound workqueue") made this particular deadlock scenario more visible but the underlying problem has always been there - the original forker task and jbd2 are freezable too. In fact, this is highly likely just one of many possible deadlock scenarios given that freezer behaves as a big kernel lock and we don't have any debug mechanism around it. I believe the right thing to do is getting rid of freezable kthreads and workqueues. This is something fundamentally broken. For now, implement a funny workaround in libata - just avoid doing block device hot[un]plug while the system is frozen. Kernel engineering at its finest. :( v2: Add EXPORT_SYMBOL_GPL(pm_freezing) for cases where libata is built as a module. v3: Comment updated and polling interval changed to 10ms as suggested by Rafael. v4: Add #ifdef CONFIG_FREEZER around the hack as pm_freezing is not defined when FREEZER is not configured thus breaking build. Reported by kbuild test robot. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Tomaž Šolc <tomaz.solc@tablix.org> Reviewed-by: "Rafael J. Wysocki" <rjw@rjwysocki.net> Link: https://bugzilla.kernel.org/show_bug.cgi?id=62801 Link: http://lkml.kernel.org/r/20131213174932.GA27070@htj.dyndns.org Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Len Brown <len.brown@intel.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata: disable a disk via libata.force paramsRobin H. Johnson2014-01-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit b8bd6dc36186fe99afa7b73e9e2d9a98ad5c4865 upstream. A user on StackExchange had a failing SSD that's soldered directly onto the motherboard of his system. The BIOS does not give any option to disable it at all, so he can't just hide it from the OS via the BIOS. The old IDE layer had hdX=noprobe override for situations like this, but that was never ported to the libata layer. This patch implements a disable flag for libata.force. Example use: libata.force=2.0:disable [v2 of the patch, removed the nodisable flag per Tejun Heo] Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Tejun Heo <tj@kernel.org> Link: http://unix.stackexchange.com/questions/102648/how-to-tell-linux-kernel-3-0-to-completely-ignore-a-failing-disk Link: http://askubuntu.com/questions/352836/how-can-i-tell-linux-kernel-to-completely-ignore-a-disk-as-if-it-was-not-even-co Link: http://superuser.com/questions/599333/how-to-disable-kernel-probing-for-drive Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata: Add atapi_dmadir force flagVincent Pelletier2014-01-09
| | | | | | | | | | | | | | | | | | | | | commit 966fbe193f47c68e70a80ec9991098e88e7959cb upstream. Some device require DMADIR to be enabled, but are not detected as such by atapi_id_dmadir. One such example is "Asus Serillel 2" SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR, even if the bridged device does not. As atapi_dmadir module parameter can cause problems with some devices (as per Tejun Heo's memory), enabling it globally may not be possible depending on the hardware. This patch adds atapi_dmadir in the form of a "force" horkage value, allowing global, per-bus and per-device control. Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8Michele Baldessari2014-01-09
| | | | | | | | | | | | | | | | | | | commit 87809942d3fa60bafb7a58d0bdb1c79e90a6821d upstream. We've received multiple reports in Fedora via (BZ 907193) that the Seagate Momentus SpinPoint M8 errors out when enabling AA: [ 2.555905] ata2.00: failed to enable AA (error_mask=0x1) [ 2.568482] ata2.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. Reported-by: Nicholas <arealityfarbetween@googlemail.com> Signed-off-by: Michele Baldessari <michele@acksyn.org> Tested-by: Nicholas <arealityfarbetween@googlemail.com> Acked-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* SCSI: Disable WRITE SAME for RAID and virtual host adapter driversMartin K. Petersen2013-12-12
| | | | | | | | | | | | | | | | | | | | | commit 54b2b50c20a61b51199bedb6e5d2f8ec2568fb43 upstream. Some host adapters do not pass commands through to the target disk directly. Instead they provide an emulated target which may or may not accurately report its capabilities. In some cases the physical device characteristics are reported even when the host adapter is processing commands on the device's behalf. This can lead to adapter firmware hangs or excessive I/O errors. This patch disables WRITE SAME for devices connected to host adapters that provide an emulated target. Driver writers can disable WRITE SAME by setting the no_write_same flag in the host adapter template. [jejb: fix up rejections due to eh_deadline patch] Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ahci: add Marvell 9230 to the AHCI PCI device listSamir Benmendil2013-12-04
| | | | | | | | | | | | commit 6d5278a68a75891db1df5ae1ecf83d288fc58c65 upstream. Tested with a DAWICONTROL DC-624e on 3.10.10 Signed-off-by: Samir Benmendil <samir.benmendil@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-by: Levente Kurusa <levex@linux.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ahci: disabled FBS prior to issuing software resetxiangliang yu2013-12-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 89dafa20f3daab5b3e0c13d0068a28e8e64e2102 upstream. Tested with Marvell 88se9125, attached with one port mulitplier(5 ports) and one disk, we will get following boot log messages if using current code: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330) ata8.15: Port Multiplier 1.2, 0x1b4b:0x9715 r160, 5 ports, feat 0x1/0x1f ahci 0000:03:00.0: FBS is enabled ata8.00: hard resetting link ata8.00: SATA link down (SStatus 0 SControl 330) ata8.01: hard resetting link ata8.01: SATA link down (SStatus 0 SControl 330) ata8.02: hard resetting link ata8.02: SATA link down (SStatus 0 SControl 330) ata8.03: hard resetting link ata8.03: SATA link up 6.0 Gbps (SStatus 133 SControl 133) ata8.04: hard resetting link ata8.04: failed to resume link (SControl 133) ata8.04: failed to read SCR 0 (Emask=0x40) ata8.04: failed to read SCR 0 (Emask=0x40) ata8.04: failed to read SCR 1 (Emask=0x40) ata8.04: failed to read SCR 0 (Emask=0x40) ata8.03: native sectors (2) is smaller than sectors (976773168) ata8.03: ATA-8: ST3500413AS, JC4B, max UDMA/133 ata8.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata8.03: configured for UDMA/133 ata8.04: failed to IDENTIFY (I/O error, err_mask=0x100) ata8.15: hard resetting link ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330) ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133' ata8.15: PMP revalidation failed (errno=-19) ata8.15: hard resetting link ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330) ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133' ata8.15: PMP revalidation failed (errno=-19) ata8.15: limiting SATA link speed to 3.0 Gbps ata8.15: hard resetting link ata8.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320) ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133' ata8.15: PMP revalidation failed (errno=-19) ata8.15: failed to recover PMP after 5 tries, giving up ata8.15: Port Multiplier detaching ata8.03: disabled ata8.00: disabled ata8: EH complete The reason is that current detection code doesn't follow AHCI spec: First,the port multiplier detection process look like this: ahci_hardreset(link, class, deadline) if (class == ATA_DEV_PMP) { sata_pmp_attach(dev) /* will enable FBS */ sata_pmp_init_links(ap, nr_ports); ata_for_each_link(link, ap, EDGE) { sata_std_hardreset(link, class, deadline); if (link_is_online) /* do soft reset */ ahci_softreset(link, class, deadline); } } But, according to chapter 9.3.9 in AHCI spec: Prior to issuing software reset, software shall clear PxCMD.ST to '0' and then clear PxFBS.EN to '0'. The patch test ok with kernel 3.11.1. tj: Patch white space contaminated, applied manually with trivial updates. Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ahci: Add Device IDs for Intel Wildcat Point-LPJames Ralston2013-12-04
| | | | | | | | | | | commit 9f961a5f6efc87a79571d7166257b36af28ffcfe upstream. This patch adds the AHCI-mode SATA Device IDs for the Intel Wildcat Point-LP PCH. Signed-off-by: James Ralston <james.d.ralston@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drivers/libata: Set max sector to 65535 for Slimtype DVD A DS8A9SH driveShan Hai2013-12-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 0523f037f65dba10191b0fa9c51266f90ba64630 upstream. The "Slimtype DVD A DS8A9SH" drive locks up with following backtrace when the max sector is smaller than 65535 bytes, fix it by adding a quirk to set the max sector to 65535 bytes. INFO: task flush-11:0:663 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. flush-11:0 D 00000000ffff5ceb 0 663 2 0x00000000 ffff88026d3b1710 0000000000000046 0000000000000001 0000000000000000 ffff88026f2530c0 ffff88026d365860 ffff88026d3b16e0 ffffffff812ffd52 ffff88026d4fd3d0 0000000100000001 ffff88026d3b16f0 ffff88026d3b1fd8 Call Trace: [<ffffffff812ffd52>] ? cfq_may_queue+0x52/0xf0 [<ffffffff81604338>] schedule+0x18/0x30 [<ffffffff81604392>] io_schedule+0x42/0x60 [<ffffffff812f22bb>] get_request_wait+0xeb/0x1f0 [<ffffffff81065660>] ? autoremove_wake_function+0x0/0x40 [<ffffffff812eb382>] ? elv_merge+0x42/0x210 [<ffffffff812f26ae>] __make_request+0x8e/0x4e0 [<ffffffff812f068e>] generic_make_request+0x21e/0x5e0 [<ffffffff812f0aad>] submit_bio+0x5d/0xd0 [<ffffffff81141422>] submit_bh+0xf2/0x130 [<ffffffff8114474c>] __block_write_full_page+0x1dc/0x3a0 [<ffffffff81143f60>] ? end_buffer_async_write+0x0/0x120 [<ffffffff811474e0>] ? blkdev_get_block+0x0/0x70 [<ffffffff811474e0>] ? blkdev_get_block+0x0/0x70 [<ffffffff81143f60>] ? end_buffer_async_write+0x0/0x120 [<ffffffff811449ee>] block_write_full_page_endio+0xde/0x100 [<ffffffff81144a20>] block_write_full_page+0x10/0x20 [<ffffffff81148703>] blkdev_writepage+0x13/0x20 [<ffffffff810d7525>] __writepage+0x15/0x40 [<ffffffff810d7c0f>] write_cache_pages+0x1cf/0x3e0 [<ffffffff810d7510>] ? __writepage+0x0/0x40 [<ffffffff810d7e42>] generic_writepages+0x22/0x30 [<ffffffff810d7e6f>] do_writepages+0x1f/0x40 [<ffffffff8113ae67>] writeback_single_inode+0xe7/0x3b0 [<ffffffff8113b574>] writeback_sb_inodes+0x184/0x280 [<ffffffff8113bedb>] writeback_inodes_wb+0x6b/0x1a0 [<ffffffff8113c24b>] wb_writeback+0x23b/0x2a0 [<ffffffff8113c42d>] wb_do_writeback+0x17d/0x190 [<ffffffff8113c48b>] bdi_writeback_task+0x4b/0xe0 [<ffffffff810e82a0>] ? bdi_start_fn+0x0/0x100 [<ffffffff810e8321>] bdi_start_fn+0x81/0x100 [<ffffffff810e82a0>] ? bdi_start_fn+0x0/0x100 [<ffffffff8106522e>] kthread+0x8e/0xa0 [<ffffffff81039274>] ? finish_task_switch+0x54/0xc0 [<ffffffff81003334>] kernel_thread_helper+0x4/0x10 [<ffffffff810651a0>] ? kthread+0x0/0xa0 [<ffffffff81003330>] ? kernel_thread_helper+0x0/0x10 The above trace was triggered by "dd if=/dev/zero of=/dev/sr0 bs=2048 count=32768" Signed-off-by: Shan Hai <shan.hai@windriver.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata: Fix display of sata speedGwendal Grignou2013-12-04
| | | | | | | | | | | | | | | | | | | | | | | commit 3e85c3ecbc520751324a191d23bb94873ed01b10 upstream. 6.0 Gbps link speed was not decoded properly: speed was reported at 3.0 Gbps only. Tested: On a machine where libata reports 6.0 Gbps in /var/log/messages: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Before: cat /sys/class/ata_link/link1/sata_spd 3.0 Gbps After: cat /sys/class/ata_link/link1/sata_spd 6.0 Gbps Signed-off-by: Gwendal Grignou <gwendal@google.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata: make ata_eh_qc_retry() bump scmd->allowed on bogus failuresGwendal Grignou2013-11-12
| | | | | | | | | | | | | | | | | | | | | commit f13e220161e738c2710b9904dcb3cf8bb0bcce61 upstream. libata EH decrements scmd->retries when the command failed for reasons unrelated to the command itself so that, for example, commands aborted due to suspend / resume cycle don't get penalized; however, decrementing scmd->retries isn't enough for ATA passthrough commands. Without this fix, ATA passthrough commands are not resend to the drive, and no error is signalled to the caller because: - allowed retry count is 1 - ata_eh_qc_complete fill the sense data, so result is valid - sense data is filled with untouched ATA registers. Signed-off-by: Gwendal Grignou <gwendal@google.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata: apply behavioral quirks to sil3826 PMPTerry Suereth2013-08-29
| | | | | | | | | | | | | | | | commit 8ffff94d20b7eb446e848e0046107d51b17a20a8 upstream. Fixing support for the Silicon Image 3826 port multiplier, by applying to it the same quirks applied to the Silicon Image 3726. Specifically fixes the repeated timeout/reset process which previously afflicted the 3726, as described from line 290. Slightly based on notes from: https://bugzilla.redhat.com/show_bug.cgi?id=890237 Signed-off-by: Terry Suereth <terry.suereth@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* sata_fsl: save irqs while coalescingAnthony Foiani2013-08-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 99bbdfa6bdcb4bdf5be914a48e9b46941bf30819 upstream. Before this patch, I was seeing the following lockdep splat on my MPC8315 (PPC32) target: [ 9.086051] ================================= [ 9.090393] [ INFO: inconsistent lock state ] [ 9.094744] 3.9.7-ajf-gc39503d #1 Not tainted [ 9.099087] --------------------------------- [ 9.103432] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage. [ 9.109431] scsi_eh_1/39 [HC1[1]:SC0[0]:HE0:SE1] takes: [ 9.114642] (&(&host->lock)->rlock){?.+...}, at: [<c02f4168>] sata_fsl_interrupt+0x50/0x250 [ 9.123137] {HARDIRQ-ON-W} state was registered at: [ 9.128004] [<c006cdb8>] lock_acquire+0x90/0xf4 [ 9.132737] [<c043ef04>] _raw_spin_lock+0x34/0x4c [ 9.137645] [<c02f3560>] fsl_sata_set_irq_coalescing+0x68/0x100 [ 9.143750] [<c02f36a0>] sata_fsl_init_controller+0xa8/0xc0 [ 9.149505] [<c02f3f10>] sata_fsl_probe+0x17c/0x2e8 [ 9.154568] [<c02acc90>] driver_probe_device+0x90/0x248 [ 9.159987] [<c02acf0c>] __driver_attach+0xc4/0xc8 [ 9.164964] [<c02aae74>] bus_for_each_dev+0x5c/0xa8 [ 9.170028] [<c02ac218>] bus_add_driver+0x100/0x26c [ 9.175091] [<c02ad638>] driver_register+0x88/0x198 [ 9.180155] [<c0003a24>] do_one_initcall+0x58/0x1b4 [ 9.185226] [<c05aeeac>] kernel_init_freeable+0x118/0x1c0 [ 9.190823] [<c0004110>] kernel_init+0x18/0x108 [ 9.195542] [<c000f6b8>] ret_from_kernel_thread+0x64/0x6c [ 9.201142] irq event stamp: 160 [ 9.204366] hardirqs last enabled at (159): [<c043f778>] _raw_spin_unlock_irq+0x30/0x50 [ 9.212469] hardirqs last disabled at (160): [<c000f414>] reenable_mmu+0x30/0x88 [ 9.219867] softirqs last enabled at (144): [<c002ae5c>] __do_softirq+0x168/0x218 [ 9.227435] softirqs last disabled at (137): [<c002b0d4>] irq_exit+0xa8/0xb4 [ 9.234481] [ 9.234481] other info that might help us debug this: [ 9.240995] Possible unsafe locking scenario: [ 9.240995] [ 9.246898] CPU0 [ 9.249337] ---- [ 9.251776] lock(&(&host->lock)->rlock); [ 9.255878] <Interrupt> [ 9.258492] lock(&(&host->lock)->rlock); [ 9.262765] [ 9.262765] *** DEADLOCK *** [ 9.262765] [ 9.268684] no locks held by scsi_eh_1/39. [ 9.272767] [ 9.272767] stack backtrace: [ 9.277117] Call Trace: [ 9.279589] [cfff9da0] [c0008504] show_stack+0x48/0x150 (unreliable) [ 9.285972] [cfff9de0] [c0447d5c] print_usage_bug.part.35+0x268/0x27c [ 9.292425] [cfff9e10] [c006ace4] mark_lock+0x2ac/0x658 [ 9.297660] [cfff9e40] [c006b7e4] __lock_acquire+0x754/0x1840 [ 9.303414] [cfff9ee0] [c006cdb8] lock_acquire+0x90/0xf4 [ 9.308745] [cfff9f20] [c043ef04] _raw_spin_lock+0x34/0x4c [ 9.314250] [cfff9f30] [c02f4168] sata_fsl_interrupt+0x50/0x250 [ 9.320187] [cfff9f70] [c0079ff0] handle_irq_event_percpu+0x90/0x254 [ 9.326547] [cfff9fc0] [c007a1fc] handle_irq_event+0x48/0x78 [ 9.332220] [cfff9fe0] [c007c95c] handle_level_irq+0x9c/0x104 [ 9.337981] [cfff9ff0] [c000d978] call_handle_irq+0x18/0x28 [ 9.343568] [cc7139f0] [c000608c] do_IRQ+0xf0/0x1a8 [ 9.348464] [cc713a20] [c000fc8c] ret_from_except+0x0/0x14 [ 9.353983] --- Exception: 501 at _raw_spin_unlock_irq+0x40/0x50 [ 9.353983] LR = _raw_spin_unlock_irq+0x30/0x50 [ 9.364839] [cc713af0] [c043db10] wait_for_common+0xac/0x188 [ 9.370513] [cc713b30] [c02ddee4] ata_exec_internal_sg+0x2b0/0x4f0 [ 9.376699] [cc713be0] [c02de18c] ata_exec_internal+0x68/0xa8 [ 9.382454] [cc713c20] [c02de4b8] ata_dev_read_id+0x158/0x594 [ 9.388205] [cc713ca0] [c02ec244] ata_eh_recover+0xd88/0x13d0 [ 9.393962] [cc713d20] [c02f2520] sata_pmp_error_handler+0xc0/0x8ac [ 9.400234] [cc713dd0] [c02ecdc8] ata_scsi_port_error_handler+0x464/0x5e8 [ 9.407023] [cc713e10] [c02ecfd0] ata_scsi_error+0x84/0xb8 [ 9.412528] [cc713e40] [c02c4974] scsi_error_handler+0xd8/0x47c [ 9.418457] [cc713eb0] [c004737c] kthread+0xa8/0xac [ 9.423355] [cc713f40] [c000f6b8] ret_from_kernel_thread+0x64/0x6c This fix was suggested by Bhushan Bharat <R65777@freescale.com>, and was discussed in email at: http://linuxppc.10917.n7.nabble.com/MPC8315-reboot-failure-lockdep-splat-possibly-related-tp75162.html Same patch successfully tested with 3.9.7. linux-next compiled but not tested on hardware. This patch is based off linux-next tag next-20130819 (which is commit 66a01bae29d11916c09f9f5a937cafe7d402e4a5 ) Signed-off-by: Anthony Foiani <anthony.foiani@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata: make it clear that sata_inic162x is experimentalTejun Heo2013-08-04
| | | | | | | | | | | | | | | | | | | | commit bb9696192826a7d9279caf872e95b41bc26c7eff upstream. sata_inic162x never reached a state where it's reliable enough for production use and data corruption is a relatively common occurrence. Make the driver generate warning about the issues and mark the Kconfig option as experimental. If the situation doesn't improve, we'd be better off making it depend on CONFIG_BROKEN. Let's wait for several cycles and see if the kernel message draws any attention. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Martin Braure de Calignon <braurede@free.fr> Reported-by: Ben Hutchings <ben@decadent.org.uk> Reported-by: risc4all@yahoo.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ata: Fix DVD not dectected at some platform with Wellsburg PCHYouquan Song2013-08-04
| | | | | | | | | | | | | | | | commit eac27f04a71e1f39f196f7e520d16dcefc955d77 upstream. There is a patch b55f84e2d527182e7c611d466cd0bb6ddce201de "ata_piix: Fix DVD not dectected at some Haswell platforms" to fix an issue of DVD not recognized on Haswell Desktop platform with Lynx Point. Recently, it is also found the same issue at some platformas with Wellsburg PCH. So deliver a similar patch to fix it by disables 32bit PIO in IDE mode. Signed-off-by: Youquan Song <youquan.song@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* sata_highbank: increase retry count but shorten duration for Calxeda controllerMark Langsdorf2013-07-25
| | | | | | | | | | | | | | commit ddfef5de3d716f77bad32dbbba6b280158dfd721 upstream. Increase the retry count for the hard reset function to 100 but shorten the time out period to 500 ms. See the comment for ahci_highbank_hardreset for the reasons why those vaulues were chosen. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDsSeth Heasley2013-07-25
| | | | | | | | | | | commit c7e8695bfa0611b39493a9dfe8bab9f63f9809bd upstream. This patch adds the IDE-mode SATA DeviceIDs for the Intel Coleto Creek PCH. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata: skip SRST for all SIMG [34]7x port-multipliersTejun Heo2013-07-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 7a87718d92760fc688628ad6a430643dafa16f1f upstream. For some reason, a lot of port-multipliers have issues with softreset. SIMG [34]7x series port-multipliers have been quite erratic in this regard. I recall that it was better with some firmware revisions and the current list of quirks worked fine for a while. I think it got worse with later firmwares or maybe my test coverage wasn't good enough. Anyways, HPA is reporting that his 3726 setup suffers SRST failures and then the PMP gets confused and fails to probe the last port. The hope was that we try to stick to the standard as much as possible and soonish the PMPs and their firmwares will improve in quality, so the quirk list was kept to minimum. Well, it seems like that's never gonna happen. Let's set NO_SRST for all [34]7x PMPs so that whatever remaining userbase of the device suffer the least. Maybe we should do the same for 57xx's but unfortunately I don't have any device left to test and I'm not even sure 57xx's have ever been made widely available, so let's leave those alone for now. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata-zpodd: must use ata_tf_init()Sergei Shtylyov2013-07-25
| | | | | | | | | | | | | | | commit d0887c43f51c308b01605346e55d906ba858a6f9 upstream. There are some SATA controllers which have both devices 0 and 1 but this module just zeroes out taskfile and sets then ATA_TFLAG_DEVICE (not sure that's needed) which could lead to a wrong device being selected just before issuing command. Thus we should call ata_tf_init() which sets up the device register value properly, like all other users of ata_exec_internal() do... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ahci: remove pmp link online check in FBS EHShane Huang2013-07-21
| | | | | | | | | | | | | | commit 912b9ac683b112615d5605686f1dc086402ce9f7 upstream. ata_link_online() check in ahci_error_intr() is unnecessary, it should be removed otherwise may lead to lockup with FBS enabled PMP. http://marc.info/?l=linux-ide&m=137050421603272&w=2 Reported-by: Yu Liu <liuyu.ac@gmail.com> Signed-off-by: Shane Huang <shane.huang@amd.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDsSeth Heasley2013-07-21
| | | | | | | | | | | commit 1cfc7df3de10c40ed459e13cce6de616023bf41c upstream. This patch adds the AHCI-mode SATA DeviceIDs for the Intel Coleto Creek PCH. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ahci: Add AMD CZ SATA device IDShane Huang2013-07-21
| | | | | | | | | | | | | commit fafe5c3d82a470d73de53e6b08eb4e28d974d895 upstream. To add AMD CZ SATA controller device ID of IDE mode. [bhelgaas: drop pci_ids.h update] Signed-off-by: Shane Huang <shane.huang@amd.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* libata-acpi: add back ACPI based hotplug functionalityAaron Lu2013-06-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 30dcf76acc69 "libata: migrate ACPI code over to new bindings" mistakenly dropped the code to register hotplug notificaion handler for ATA port/devices, causing regression for people using ATA bay, as kernel bug #59871 shows. Fix this by adding back the hotplug notification handler registration code. Since this code has to be run once and notification needs to be installed on every ATA port/devices handle no matter if there is actual device attached, we can't do this in binding time for ATA device ACPI handle, as the binding only occurs when a SCSI device is created, i.e. there is device attached. So introduce the ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles and if it is available, install the notificaion handler for it during ATA init time. With the ATA ACPI handle binding to SCSI device tree, it is possible now that when the SCSI hotplug work removes the SCSI device, the ACPI unbind function will find that the corresponding ACPI device has already been deleted by dock driver, causing a scaring message like: [ 128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt Fix this by waiting for SCSI hotplug task finish in our notificaion handler, so that the removal of ACPI device done in ACPI unbind function triggered by the removal of SCSI device is run earlier when ACPI device is still available. [rjw: Rebased] References: https://bugzilla.kernel.org/show_bug.cgi?id=59871 Reported-bisected-and-tested-by: Dirk Griesbach <spamthis@freenet.de> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: 3.6+ <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Merge branch 'for-3.10-fixes' of ↵Linus Torvalds2013-06-03
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata changes from Tejun Heo: "Nothing too interesting. PCI ID additions, some sata_rcar fixes and a fringe bug fix for DMADIR handling which shouldn't affect any device remotely modern." * 'for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: sata_rcar: fix interrupt handling ahci: add an observed PCI ID for Marvell 88se9172 SATA controller sata_rcar: clear STOP bit in bmdma_start() method libata: make ata_exec_internal_sg honor DMADIR ata_piix: add PCI IDs for Intel BayTail libata: update "Maintained by:" tags
| * sata_rcar: fix interrupt handlingSergei Shtylyov2013-06-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The driver's interrupt handling code is too picky in deciding whether it should handle an interrupt or not which causes completely unneeded spurious interrupts. Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't get cleared by writing to the SATAINTSTAT register in the interrupt mode we use. Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for enabled interrupts and we should clear only those interrupts that we have read as active first time around, because else we have a race and risk clearing an interrupt that can occur between read and write of the SATAINTSTAT register and never registering it... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
| * ahci: add an observed PCI ID for Marvell 88se9172 SATA controllerGeorge Spelvin2013-05-28
| | | | | | | | | | | | | | | | A third possible PCI ID, as personally observed, and found in the pci.ids list. Signed-off-by: George Spelvin <linux@horizon.com> Signed-off-by: Tejun Heo <tj@kernel.org>
| * sata_rcar: clear STOP bit in bmdma_start() methodSergei Shtylyov2013-05-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Iff bmdma_setup() has to stop a DMA transfer before starting a new one, then the STOP bit in the ATAPI_CONTROL1 register will remain set (it's only cleared when setting the START bit to 1) and then bmdma_start() method will set both START and STOP bits simultaneously which should abort the transfer being just started. Avoid that by explicitly clearing the STOP bit in bmdma_start() method (in this case it will be ignored on write). Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
| * libata: make ata_exec_internal_sg honor DMADIRVincent Pelletier2013-05-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | libata honors DMADIR for regular commands, but not for internal commands used (among other) during device initialisation. This makes SATA-host-to-PATA-device bridges based on Silicon Image SiL3611 (such as "Abit Serillel 2") end up disabled when used with an ATAPI device after a few tries. Log output of the bridge being hot-plugged with an ATAPI drive: [ 9631.212901] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen [ 9631.212913] ata1: irq_stat 0x00000040, connection status changed [ 9631.212923] ata1: SError: { CommWake 10B8B DevExch } [ 9631.212939] ata1: hard resetting link [ 9632.104962] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9632.106393] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33 [ 9632.106407] ata1.00: applying bridge limits [ 9632.108151] ata1.00: configured for UDMA/33 [ 9637.105303] ata1.00: qc timeout (cmd 0xa0) [ 9637.105324] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5) [ 9637.105335] ata1: hard resetting link [ 9638.044599] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9638.047878] ata1.00: configured for UDMA/33 [ 9643.044933] ata1.00: qc timeout (cmd 0xa0) [ 9643.044953] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5) [ 9643.044963] ata1: limiting SATA link speed to 1.5 Gbps [ 9643.044971] ata1.00: limiting speed to UDMA/33:PIO3 [ 9643.044979] ata1: hard resetting link [ 9643.984225] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 9643.987471] ata1.00: configured for UDMA/33 [ 9648.984591] ata1.00: qc timeout (cmd 0xa0) [ 9648.984612] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5) [ 9648.984619] ata1.00: disabled [ 9649.000593] ata1: hard resetting link [ 9649.939902] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 9649.955864] ata1: EH complete With this patch, the drive enumerates correctly when libata is loaded with atapi_dmadir=1: [ 9891.810863] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen [ 9891.810874] ata1: irq_stat 0x00000040, connection status changed [ 9891.810884] ata1: SError: { CommWake 10B8B DevExch } [ 9891.810900] ata1: hard resetting link [ 9892.762105] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9892.763544] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33, DMADIR [ 9892.763558] ata1.00: applying bridge limits [ 9892.765393] ata1.00: configured for UDMA/33 [ 9892.786063] ata1: EH complete [ 9892.792062] scsi 0:0:0:0: CD-ROM PIONEER DVD-RW DVR-115 1.06 PQ: 0 ANSI: 5 [ 9892.798455] sr2: scsi3-mmc drive: 12x/12x writer dvd-ram cd/rw xa/form2 cdda tray [ 9892.798837] sr 0:0:0:0: Attached scsi CD-ROM sr2 [ 9892.799109] sr 0:0:0:0: Attached scsi generic sg6 type 5 Based on a patch by Csaba Halász <csaba.halasz@gmail.com> on linux-ide: http://marc.info/?l=linux-ide&m=136121147832295&w=2 tj: minor formatting changes. Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
| * ata_piix: add PCI IDs for Intel BayTailChew, Chiau Ee2013-05-16
| | | | | | | | | | | | | | | | | | Adds IDE-mode SATA Device IDs for the Intel BayTrail platform. Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
| * libata: update "Maintained by:" tagsTejun Heo2013-05-14
| | | | | | | | | | | | | | | | | | Jeff moved on to a greener pasture. s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jeff Garzik <jgarzik@pobox.com>
* | drivers/ata: don't check resource with devm_ioremap_resourceWolfram Sang2013-05-12
|/ | | | | | | devm_ioremap_resource does sanity checks on the given resource. No need to duplicate this in the driver. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* Merge tag 'cleanup-for-linus-2' of ↵Linus Torvalds2013-05-07
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC late cleanups from Arnd Bergmann: "These are cleanups and smaller changes that either depend on earlier feature branches or came in late during the development cycle. We normally try to get all cleanups early, so these are the exceptions: - A follow-up on the clocksource reworks, hopefully the last time we need to merge clocksource subsystem changes through arm-soc. A first set of patches was part of the original 3.10 arm-soc cleanup series because of interdependencies with timer drivers now moved out of arch/arm. - Migrating the SPEAr13xx platform away from using auxdata for DMA channel descriptions towards using information in device tree, based on the earlier SPEAr multiplatform series - A few follow-ups on the Atmel SAMA5 support and other changes for Atmel at91 based on the larger at91 reworks. - Moving the armada irqchip implementation to drivers/irqchip - Several OMAP cleanups following up on the larger series already merged in 3.10." * tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits) ARM: OMAP4: change the device names in usb_bind_phy ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a ARM: SPEAr: conditionalize SMP code ARM: arch_timer: Silence debug preempt warnings ARM: OMAP: remove unused variable serial: amba-pl011: fix !CONFIG_DMA_ENGINE case ata: arasan: remove the need for platform_data ARM: at91/sama5d34ek.dts: remove not needed compatibility string ARM: at91: dts: add MCI DMA support ARM: at91: dts: add i2c dma support ARM: at91: dts: set #dma-cells to the correct value ARM: at91: suspend both memory controllers on at91sam9263 irqchip: armada-370-xp: slightly cleanup irq controller driver irqchip: armada-370-xp: move IRQ handler to avoid forward declaration irqchip: move IRQ driver for Armada 370/XP ARM: mvebu: move L2 cache initialization in init_early() devtree: add binding documentation for sp804 ARM: integrator-cp: convert use CLKSRC_OF for timer init ARM: versatile: use OF init for sp804 timer ARM: versatile: add versatile dtbs to dtbs target ...
| * Merge branch 'spear/dwdma' into late/cleanupArnd Bergmann2013-04-19
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a series originally prepared for inclusion in 3.9, which did not work out because of dependencies on the dmaengine driver. All the changes for the dmaengine code are merged in 3.9 now, so we can finally do the switchover and remove the now unnecessary dma definitions for spear13xx from the platform code. The dma platform_data actually made up the majority of the spear13xx platform code overall, so moving that into device tree files makes the code substantially smaller. * spear/dwdma: ata: arasan: remove the need for platform_data ARM: SPEAr13xx: Pass generic DW DMAC platform data from DT serial: pl011: use generic DMA slave configuration if possible spi: pl022: use generic DMA slave configuration if possible Signed-off-by: Arnd Bergmann <arnd@arndb.de>
| | * ata: arasan: remove the need for platform_dataArnd Bergmann2013-04-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a complete DT binding for the arasan device driver. There is currently only one user, which is the spear13xx platform, so we don't actually have to parse all the properties until another user comes in, but this does use the generic DMA binding to find the DMA channel. The patch is untested so far and is part of a series to convert the spear platform over to use the generic DMA binding, so it should stay with the rest of the series. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Viresh Kumar <viresh.linux@linaro.org> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Jeff Garzik <jgarzik@redhat.com> Cc: devicetree-discuss@lists.ozlabs.org
* | | Merge branch 'for-linus' of ↵Linus Torvalds2013-05-01
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull VFS updates from Al Viro, Misc cleanups all over the place, mainly wrt /proc interfaces (switch create_proc_entry to proc_create(), get rid of the deprecated create_proc_read_entry() in favor of using proc_create_data() and seq_file etc). 7kloc removed. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits) don't bother with deferred freeing of fdtables proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h proc: Make the PROC_I() and PDE() macros internal to procfs proc: Supply a function to remove a proc entry by PDE take cgroup_open() and cpuset_open() to fs/proc/base.c ppc: Clean up scanlog ppc: Clean up rtas_flash driver somewhat hostap: proc: Use remove_proc_subtree() drm: proc: Use remove_proc_subtree() drm: proc: Use minor->index to label things, not PDE->name drm: Constify drm_proc_list[] zoran: Don't print proc_dir_entry data in debug reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show() proc: Supply an accessor for getting the data from a PDE's parent airo: Use remove_proc_subtree() rtl8192u: Don't need to save device proc dir PDE rtl8187se: Use a dir under /proc/net/r8180/ proc: Add proc_mkdir_data() proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h} proc: Move PDE_NET() to fs/proc/proc_net.c ...
| * | | sata_svw: switch to ->show_info()Al Viro2013-04-09
| |/ / | | | | | | | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* | | Merge tag 'upstream-linus' of ↵Linus Torvalds2013-04-30
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev Pull libata update from Jeff Garzik: - More ACPI fixes, cleanups - Minor cleanups for sata_highbank, pata_at32, pata_octeon_cf, sata_rcar - pata_legacy: small bug found in opti chipset code (untested fix, due to ancient h/w) - sata_fsl: RX water mark config knob, some h/w needs it - pata_imx: cleanups, DeviceTree support - SCSI<->ATA translator: properly export translator version, not device firmware version * tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: sata_highbank: Rename proc_name to the module name ACPI/libata: Restore libata.noacpi support [libata] acpi: make ata_ap_acpi_handle not block [libata] SCSI: really use SATL version in VPD pata_imx: add devicetree support pata_imx: use void __iomem * for regs pata_imx: cleanup error path pata_imx: Use devm_clk_get sata_rcar: Convert to devm_ioremap_resource() fsl/sata: create a sysfs entry for rx water mark libata-acpi: remove redundent code for power resource handling sata_highbank: make ahci_highbank_pm_ops static pata_octeon_cf: Use resource_size function pata_legacy: bogus clock in opti82c46x_set_piomode() pata_at32: use module_platform_driver_probe()
| * | | sata_highbank: Rename proc_name to the module nameRobert Richter2013-04-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mkinitrd looks at /sys/class/scsi_host/host$hostnum/proc_name to find the module name of a disk driver. Current name is "highbank-ahci" but the module is "sata_highbank". Rename it to match the module name. Cc: Rob Herring <rob.herring@calxeda.com> Cc: Alexander Graf <agraf@suse.de> Cc: <stable@vger.kernel.org> v3.7.. Signed-off-by: Robert Richter <robert.richter@calxeda.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | ACPI/libata: Restore libata.noacpi supportLv Zheng2013-04-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch restores libata.noacpi support to libata-acpi.c. There are broken optional control methods for ATA controller devices in the real world. The libata.noacpi has been used for a long time as a workaround to deal with issues caused by the broken ASL codes. 1. The "noacpi" option is introduced by the following commit: commit 11ef697b37e3c85ce1ac21f7711babf1f5b12784 Date: Thu, 28 Sep 2006 11:29:01 -0700 Subject: libata: ACPI and _GTF support 2. The "noacpi" option is renamed to "libata_noacpi" by the following commit: commit d7d0dad62a641c156386288a747c1a2f6bb2e42d Date: Wed, 28 Mar 2007 01:57:37 -0400 Subject: [libata] Disable ACPI by default; fix namespace problems 3. Some of its logics are changed over time - becomes relying on the "acpi_handle" bound to the ATA devices since this commit: commit fafbae87db88a73b166d3bc3294d209207f27056 Date: Tue, 15 May 2007 03:28:16 +0900 Subject: libata-acpi: implement ata_acpi_associate() 4. The option is deleted by the following commit: commit 30dcf76acc695cbd2fa919e294670fe9552e16e7 Date: Mon, 25 Jun 2012 16:13:04 +0800 Subject: libata: migrate ACPI code over to new bindings But the libata.noacpi setup is still left in the kernel without codes to implement it. So the deletion introduces a regression to the Linux. This patch disables ATA_ACPI support at runtime by stopping acpi binding on the ATA devices to fix this regression. This patch is tested by booting a SATA x86-64 kernel or a PATA x86 kernel with or without "libata.noacpi=1" kernel command line argument. Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | [libata] acpi: make ata_ap_acpi_handle not blockAaron Lu2013-04-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 30dcf76acc, ata_ap_acpi_handle will always do a namespace walk, which requires acquiring an acpi namespace mutex. This made it impossible to be used when calling path has held a spinlock. For example, it can occur in the following code path for pata_acpi: ata_scsi_queuecmd (ap->lock is acquired) __ata_scsi_queuecmd ata_scsi_translate ata_qc_issue pacpi_qc_issue ata_acpi_stm ata_ap_acpi_handle acpi_get_child acpi_walk_namespace acpi_ut_acquire_mutex (acquire mutex while holding lock) This caused scheduling while atomic bug, as reported in bug #56781. Actually, ata_ap_acpi_handle doesn't have to walk the namespace every time it is called, it can simply return the bound acpi handle on the corresponding SCSI host. The reason previously it is not done this way is, ata_ap_acpi_handle is used in the binding function ata_acpi_bind_host by ata_acpi_gtm when the handle is not bound to the SCSI host yet. Since we already have the ATA port's handle in its binding function, we can simply use it instead of calling ata_ap_acpi_handle there. So introduce a new function __ata_acpi_gtm, where it will receive an acpi handle param in addition to the ATA port which is solely used for debug statement. With this change, we can make ata_ap_acpi_handle simply return the bound handle for SCSI host instead of walking the acpi namespace now. Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=56781 Reported-and-tested-by: <kenzopl@o2.pl> Cc: <stable@vger.kernel.org> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | [libata] SCSI: really use SATL version in VPDBaruch Even2013-04-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As per c78968bb by Jeff Garzik ([libata] SCSI: simulator version, not device version, belongs in VPD) We need to provide the SATL driver version and not the disk firmware version but the code overwrites the driver version with the disk version. Signed-off-by: Baruch Even <baruch@ev-en.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * | | pata_imx: add devicetree supportSascha Hauer2013-04-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Not much to do here, only the compatible entries have to be added. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-04-04 04:40:22 -0400