6 files changed, 19 insertions, 31 deletions

diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index f2ab4ea7cc0e..581cb081cb0f 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -44,6 +44,8 @@
                         compatible = "ti,omap2-intc";
                         interrupt-controller;
                         #interrupt-cells = <1>;
+                        ti,intc-size = <96>;
+                        reg = <0x480FE000 0x1000>;
                 };
 
                 uart1: serial@4806a000 {
diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index 8ca14e88a31a..2c5d0ed75285 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -83,11 +83,9 @@ static struct musb_hdrc_config musb_config = {
 };
 
 static struct musb_hdrc_platform_data tusb_data = {
-#if defined(CONFIG_USB_MUSB_OTG)
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
         .mode           = MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
-        .mode           = MUSB_PERIPHERAL,
-#else /* defined(CONFIG_USB_MUSB_HOST) */
+#else
         .mode           = MUSB_HOST,
 #endif
         .set_power      = tusb_set_power,
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 79c6909eeb78..580fd17208da 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -81,13 +81,13 @@ static u8 omap3_beagle_version;
 static struct {
         int mmc1_gpio_wp;
         int usb_pwr_level;
-        int reset_gpio;
+        int dvi_pd_gpio;
         int usr_button_gpio;
         int mmc_caps;
 } beagle_config = {
         .mmc1_gpio_wp = -EINVAL,
         .usb_pwr_level = GPIOF_OUT_INIT_LOW,
-        .reset_gpio = 129,
+        .dvi_pd_gpio = -EINVAL,
         .usr_button_gpio = 4,
         .mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 };
@@ -126,21 +126,21 @@ static void __init omap3_beagle_init_rev(void)
                 printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
                 omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
                 beagle_config.mmc1_gpio_wp = 29;
-                beagle_config.reset_gpio = 170;
+                beagle_config.dvi_pd_gpio = 170;
                 beagle_config.usr_button_gpio = 7;
                 break;
         case 6:
                 printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
                 omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
                 beagle_config.mmc1_gpio_wp = 23;
-                beagle_config.reset_gpio = 170;
+                beagle_config.dvi_pd_gpio = 170;
                 beagle_config.usr_button_gpio = 7;
                 break;
         case 5:
                 printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
                 omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
                 beagle_config.mmc1_gpio_wp = 23;
-                beagle_config.reset_gpio = 170;
+                beagle_config.dvi_pd_gpio = 170;
                 beagle_config.usr_button_gpio = 7;
                 break;
         case 0:
@@ -274,11 +274,9 @@ static int beagle_twl_gpio_setup(struct device *dev,
                 if (r)
                         pr_err("%s: unable to configure nDVI_PWR_EN\n",
                                 __func__);
-                r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
-                                     "DVI_LDO_EN");
-                if (r)
-                        pr_err("%s: unable to configure DVI_LDO_EN\n",
-                                __func__);
+
+                beagle_config.dvi_pd_gpio = gpio + 2;
+
         } else {
                 /*
                  * REVISIT: need ehci-omap hooks for external VBUS
@@ -287,7 +285,7 @@ static int beagle_twl_gpio_setup(struct device *dev,
                 if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
                         pr_err("%s: unable to configure EHCI_nOC\n", __func__);
         }
-        dvi_panel.power_down_gpio = beagle_config.reset_gpio;
+        dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio;
 
         gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
                         "nEN_USB_PWR");
@@ -499,7 +497,7 @@ static void __init omap3_beagle_init(void)
         omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
         omap3_beagle_init_rev();
 
-        if (beagle_config.mmc1_gpio_wp != -EINVAL)
+        if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
                 omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
         mmc[0].caps = beagle_config.mmc_caps;
         omap_hsmmc_init(mmc);
@@ -510,15 +508,13 @@ static void __init omap3_beagle_init(void)
 
         platform_add_devices(omap3_beagle_devices,
                         ARRAY_SIZE(omap3_beagle_devices));
+        if (gpio_is_valid(beagle_config.dvi_pd_gpio))
+                omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
         omap_display_init(&beagle_dss_data);
         omap_serial_init();
         omap_sdrc_init(mt46h32m32lf6_sdrc_params,
                                   mt46h32m32lf6_sdrc_params);
 
-        omap_mux_init_gpio(170, OMAP_PIN_INPUT);
-        /* REVISIT leave DVI powered down until it's needed ... */
-        gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
-
         usb_musb_init(NULL);
         usbhs_init(&usbhs_bdata);
         omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c
index 4c90477e6f82..d52651a05daa 100644
--- a/arch/arm/mach-omap2/omap_phy_internal.c
+++ b/arch/arm/mach-omap2/omap_phy_internal.c
@@ -239,21 +239,15 @@ void am35x_set_mode(u8 musb_mode)
 
         devconf2 &= ~CONF2_OTGMODE;
         switch (musb_mode) {
-#ifdef  CONFIG_USB_MUSB_HDRC_HCD
         case MUSB_HOST:         /* Force VBUS valid, ID = 0 */
                 devconf2 |= CONF2_FORCE_HOST;
                 break;
-#endif
-#ifdef  CONFIG_USB_GADGET_MUSB_HDRC
         case MUSB_PERIPHERAL:   /* Force VBUS valid, ID = 1 */
                 devconf2 |= CONF2_FORCE_DEVICE;
                 break;
-#endif
-#ifdef  CONFIG_USB_MUSB_OTG
         case MUSB_OTG:          /* Don't override the VBUS/ID comparators */
                 devconf2 |= CONF2_NO_OVERRIDE;
                 break;
-#endif
         default:
                 pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode);
         }
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index b19d1b43c12e..c4a576856661 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -41,12 +41,10 @@ static struct musb_hdrc_config musb_config = {
 };
 
 static struct musb_hdrc_platform_data musb_plat = {
-#ifdef CONFIG_USB_MUSB_OTG
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
         .mode           = MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+#else
         .mode           = MUSB_HOST,
-#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
-        .mode           = MUSB_PERIPHERAL,
 #endif
         /* .clock is set dynamically */
         .config         = &musb_config,
diff --git a/arch/arm/mach-omap2/usb-tusb6010.c b/arch/arm/mach-omap2/usb-tusb6010.c
index db84a46ce7fd..805bea6edf17 100644
--- a/arch/arm/mach-omap2/usb-tusb6010.c
+++ b/arch/arm/mach-omap2/usb-tusb6010.c
@@ -300,7 +300,7 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data,
                 printk(error, 3, status);
                 return status;
         }
-        tusb_resources[2].start = irq + IH_GPIO_BASE;
+        tusb_resources[2].start = gpio_to_irq(irq);
 
         /* set up memory timings ... can speed them up later */
         if (!ps_refclk) {