aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/3c503.h
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 18:20:36 -0400
committerLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 18:20:36 -0400
commit1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 (patch)
tree0bba044c4ce775e45a88a51686b5d9f90697ea9d /drivers/net/3c503.h
Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
Diffstat (limited to 'drivers/net/3c503.h')
-rw-r--r--drivers/net/3c503.h91
1 files changed, 91 insertions, 0 deletions
diff --git a/drivers/net/3c503.h b/drivers/net/3c503.h
new file mode 100644
index 000000000000..b9f8a46f89b3
--- /dev/null
+++ b/drivers/net/3c503.h
@@ -0,0 +1,91 @@
1/* Definitions for the 3Com 3c503 Etherlink 2. */
2/* This file is distributed under the GPL.
3 Many of these names and comments are directly from the Crynwr packet
4 drivers, which are released under the GPL. */
5
6#define EL2H (dev->base_addr + 0x400)
7#define EL2L (dev->base_addr)
8
9/* Vendor unique hardware addr. prefix. 3Com has 2 because they ran
10 out of available addresses on the first one... */
11
12#define OLD_3COM_ID 0x02608c
13#define NEW_3COM_ID 0x0020af
14
15/* Shared memory management parameters. NB: The 8 bit cards have only
16 one bank (MB1) which serves both Tx and Rx packet space. The 16bit
17 cards have 2 banks, MB0 for Tx packets, and MB1 for Rx packets.
18 You choose which bank appears in the sh. mem window with EGACFR_MBSn */
19
20#define EL2_MB0_START_PG (0x00) /* EL2/16 Tx packets go in bank 0 */
21#define EL2_MB1_START_PG (0x20) /* First page of bank 1 */
22#define EL2_MB1_STOP_PG (0x40) /* Last page +1 of bank 1 */
23
24/* 3Com 3c503 ASIC registers */
25#define E33G_STARTPG (EL2H+0) /* Start page, matching EN0_STARTPG */
26#define E33G_STOPPG (EL2H+1) /* Stop page, must match EN0_STOPPG */
27#define E33G_DRQCNT (EL2H+2) /* DMA burst count */
28#define E33G_IOBASE (EL2H+3) /* Read of I/O base jumpers. */
29 /* (non-useful, but it also appears at the end of EPROM space) */
30#define E33G_ROMBASE (EL2H+4) /* Read of memory base jumpers. */
31#define E33G_GACFR (EL2H+5) /* Config/setup bits for the ASIC GA */
32#define E33G_CNTRL (EL2H+6) /* Board's main control register */
33#define E33G_STATUS (EL2H+7) /* Status on completions. */
34#define E33G_IDCFR (EL2H+8) /* Interrupt/DMA config register */
35 /* (Which IRQ to assert, DMA chan to use) */
36#define E33G_DMAAH (EL2H+9) /* High byte of DMA address reg */
37#define E33G_DMAAL (EL2H+10) /* Low byte of DMA address reg */
38/* "Vector pointer" - if this address matches a read, the EPROM (rather than
39 shared RAM) is mapped into memory space. */
40#define E33G_VP2 (EL2H+11)
41#define E33G_VP1 (EL2H+12)
42#define E33G_VP0 (EL2H+13)
43#define E33G_FIFOH (EL2H+14) /* FIFO for programmed I/O moves */
44#define E33G_FIFOL (EL2H+15) /* ... low byte of above. */
45
46/* Bits in E33G_CNTRL register: */
47
48#define ECNTRL_RESET (0x01) /* Software reset of the ASIC and 8390 */
49#define ECNTRL_THIN (0x02) /* Onboard xcvr enable, AUI disable */
50#define ECNTRL_AUI (0x00) /* Onboard xcvr disable, AUI enable */
51#define ECNTRL_SAPROM (0x04) /* Map the station address prom */
52#define ECNTRL_DBLBFR (0x20) /* FIFO configuration bit */
53#define ECNTRL_OUTPUT (0x40) /* PC-to-3C503 direction if 1 */
54#define ECNTRL_INPUT (0x00) /* 3C503-to-PC direction if 0 */
55#define ECNTRL_START (0x80) /* Start the DMA logic */
56
57/* Bits in E33G_STATUS register: */
58
59#define ESTAT_DPRDY (0x80) /* Data port (of FIFO) ready */
60#define ESTAT_UFLW (0x40) /* Tried to read FIFO when it was empty */
61#define ESTAT_OFLW (0x20) /* Tried to write FIFO when it was full */
62#define ESTAT_DTC (0x10) /* Terminal Count from PC bus DMA logic */
63#define ESTAT_DIP (0x08) /* DMA In Progress */
64
65/* Bits in E33G_GACFR register: */
66
67#define EGACFR_NIM (0x80) /* NIC interrupt mask */
68#define EGACFR_TCM (0x40) /* DMA term. count interrupt mask */
69#define EGACFR_RSEL (0x08) /* Map a bank of card mem into system mem */
70#define EGACFR_MBS2 (0x04) /* Memory bank select, bit 2. */
71#define EGACFR_MBS1 (0x02) /* Memory bank select, bit 1. */
72#define EGACFR_MBS0 (0x01) /* Memory bank select, bit 0. */
73
74#define EGACFR_NORM (0x49) /* TCM | RSEL | MBS0 */
75#define EGACFR_IRQOFF (0xc9) /* TCM | RSEL | MBS0 | NIM */
76
77/*
78 MBS2 MBS1 MBS0 Sh. mem windows card mem at:
79 ---- ---- ---- -----------------------------
80 0 0 0 0x0000 -- bank 0
81 0 0 1 0x2000 -- bank 1 (only choice for 8bit card)
82 0 1 0 0x4000 -- bank 2, not used
83 0 1 1 0x6000 -- bank 3, not used
84
85There was going to be a 32k card that used bank 2 and 3, but it
86never got produced.
87
88*/
89
90
91/* End of 3C503 parameter definitions */