aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath/ath9k/mci.h
Commit message (Collapse)AuthorAge
* ath9k: Add new BT profile info A2DP_VoiceRajkumar Manoharan2012-10-29
| | | | | | | | | | When the BT connection is initiated by headset, it's possible that headset requests to make one A2DP and one Voice connection over the same link. BT firmware will send a new profile A2DP_Voice in this case. So WLAN has to take care of this new profile for tuning BTCOEX parameters. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: adjust WLAN and BT concurrent transmissionRajkumar Manoharan2012-10-29
| | | | | | | | | | | | | | The simulataneous transmission of both WLAN and BT might cause increase in power levels. To avoid regulatory violation, WLAN tx power will be adjusted according to BT power index based on avaliability of BT scheduling messages. WLAN tx power reduction might affect its performance. So WLAN tx power is only be lowered when the signal strength is good enough. Otherwise concurrent tx will be disabled and WLAN uses it default power levels. Also concurrent tx is disabled whenever WLAN is moving to off-channel which might be used by BT. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Add concurrent WLAN and BT tx support for MCI based chipsRajkumar Manoharan2012-10-29
| | | | | | | | | | | | This feature enables both WLAN and BT can transmit simultaneously by setting WLAN and BT to equal priorities. Whenever both are transmitting, it might violate regulatory power limits. To avoid regulatory violation, WLAN tx power will be adjusted according to BT power index based on avaliability of BT scheduling message. If the combined power exceeds threshold, BT transmission will be held off. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Send WLAN channel info to BTRajkumar Manoharan2012-10-29
| | | | | | | | | | WLAN updates channel bitmap when associated and disassociated. Channel bitmap will reflect whare are the channels used or affected by WLAN and BT should avoid using those. Not doing so, could affect BT traffic as both WLAN and BT is operating on same channel. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Setup MCI interrupts properlySujith Manoharan2012-06-06
| | | | | | | | MCI interrupts have to be enabled only when BTCOEX is actually in use. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Cleanup MCI bits from hw.hSujith Manoharan2012-02-27
| | | | | | | | This patch moves all the MCI-specific declarations that have been dumped unceremoniously in hw.h to ar9003_mci.h Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Cleanup MCI init/deinit routinesSujith Manoharan2012-02-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch simplifies the buffer allocation functions for MCI and removes unneeded memset calls. Also, a couple of unused variables are removed and a memory leak in DMA allocation is fixed. [ 1263.788267] WARNING: at /home/sujith/dev/wireless-testing/lib/dma-debug.c:875 check_unmap+0x173/0x7e0() [ 1263.788273] ath9k 0000:06:00.0: DMA-API: device driver frees DMA memory with different size [device address=0x0000000071908000] [map size=512 bytes] [unmap size=256 bytes] [ 1263.788345] Pid: 774, comm: rmmod Tainted: G W O 3.3.0-rc3-wl #18 [ 1263.788348] Call Trace: [ 1263.788355] [<ffffffff8105110f>] warn_slowpath_common+0x7f/0xc0 [ 1263.788359] [<ffffffff81051206>] warn_slowpath_fmt+0x46/0x50 [ 1263.788363] [<ffffffff8125a713>] check_unmap+0x173/0x7e0 [ 1263.788368] [<ffffffff8123fc22>] ? prio_tree_left+0x32/0xc0 [ 1263.788373] [<ffffffff8125aded>] debug_dma_free_coherent+0x6d/0x80 [ 1263.788381] [<ffffffffa0701c3c>] ath_mci_cleanup+0x7c/0x110 [ath9k] [ 1263.788387] [<ffffffffa06f4033>] ath9k_deinit_softc+0x113/0x120 [ath9k] [ 1263.788392] [<ffffffffa06f55cc>] ath9k_deinit_device+0x5c/0x70 [ath9k] [ 1263.788397] [<ffffffffa0704934>] ath_pci_remove+0x54/0xa0 [ath9k] [ 1263.788401] [<ffffffff81267d06>] pci_device_remove+0x46/0x110 [ 1263.788406] [<ffffffff813102bc>] __device_release_driver+0x7c/0xe0 [ 1263.788410] [<ffffffff81310a00>] driver_detach+0xd0/0xe0 [ 1263.788414] [<ffffffff81310118>] bus_remove_driver+0x88/0xe0 [ 1263.788418] [<ffffffff813111c2>] driver_unregister+0x62/0xa0 [ 1263.788421] [<ffffffff812680c4>] pci_unregister_driver+0x44/0xc0 [ 1263.788427] [<ffffffffa0705015>] ath_pci_exit+0x15/0x20 [ath9k] [ 1263.788432] [<ffffffffa070a92d>] ath9k_exit+0x15/0x31 [ath9k] [ 1263.788436] [<ffffffff810b971c>] sys_delete_module+0x18c/0x270 [ 1263.788441] [<ffffffff81436edd>] ? retint_swapgs+0x13/0x1b [ 1263.788446] [<ffffffff812483be>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 1263.788450] [<ffffffff814378e9>] system_call_fastpath+0x16/0x1b [ 1263.788453] ---[ end trace 3ab4d030ffde40d4 ]--- Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: make two mci related functions staticFelix Fietkau2011-12-13
| | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: MCI state machine based on MCI interruptMohammed Shafi Shajakhan2011-11-30
| | | | | | | | Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Add functions to allocate/free buffers for MCIMohammed Shafi Shajakhan2011-11-30
| | | | | | | | | | | required buffers and dma allocation is done for GPM and SCHED messages Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: add MCI specific definitions and structuresMohammed Shafi Shajakhan2011-11-30
| | | | | | | | Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Add btcoex profile management support for AR9462Rajkumar Manoharan2011-11-08
AR9462 chips have the capabilities to provoide bluetooth profile information. For non-AR9462 btcoex chips, the BT priority traffic was identified by periodically polling the respective registers and updated dutycycle, stomptype, etc. As AR9462 chip offers the BT profile informations, let us make use of that to update aggregation limit, dutycycle, stomptype and wieghtages. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-04-10 22:01:32 -0400