mtd: nand: denali: remove unused CONFIG option and macros

All of these macros are not used at all.
CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR is not used for anything but
defining SCRATCH_REG_ADDR.  The config option should go away as well.

I am removing some register macros.  They are not used, and do not
exist in recent IP versions.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

3 files changed, 0 insertions, 115 deletions

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index ae7ae77f295e..aa44fb0a1b18 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -59,17 +59,6 @@ config MTD_NAND_DENALI_DT
           Enable the driver for NAND flash on platforms using a Denali NAND
           controller as a DT device.
 
-config MTD_NAND_DENALI_SCRATCH_REG_ADDR
-        hex "Denali NAND size scratch register address"
-        default "0xFF108018"
-        depends on MTD_NAND_DENALI_PCI
-        help
-          Some platforms place the NAND chip size in a scratch register
-          because (some versions of) the driver aren't able to automatically
-          determine the size of certain chips. Set the address of the
-          scratch register here to enable this feature. On Intel Moorestown
-          boards, the scratch register is at 0xFF108018.
-
 config MTD_NAND_GPIO
         tristate "GPIO assisted NAND Flash driver"
         depends on GPIOLIB || COMPILE_TEST
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index 73b9d4e2dca0..f993e1378f94 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -91,11 +91,6 @@ static inline struct denali_nand_info *mtd_to_denali(struct mtd_info *mtd)
 #define DENALI_READ     0
 #define DENALI_WRITE    0x100
 
-/* types of device accesses. We can issue commands and get status */
-#define COMMAND_CYCLE   0
-#define ADDR_CYCLE      1
-#define STATUS_CYCLE    2
-
 /*
  * this is a helper macro that allows us to
  * format the bank into the proper bits for the controller
diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/denali.h
index ea22191e8515..c4f3a683de93 100644
--- a/drivers/mtd/nand/denali.h
+++ b/drivers/mtd/nand/denali.h
@@ -257,26 +257,6 @@
 #define ERR_PAGE_ADDR(__bank)   (0x440 + ((__bank) * 0x50))
 #define ERR_BLOCK_ADDR(__bank)  (0x450 + ((__bank) * 0x50))
 
-#define DATA_INTR                               0x550
-#define     DATA_INTR__WRITE_SPACE_AV                   0x0001
-#define     DATA_INTR__READ_DATA_AV                     0x0002
-
-#define DATA_INTR_EN                            0x560
-#define     DATA_INTR_EN__WRITE_SPACE_AV                0x0001
-#define     DATA_INTR_EN__READ_DATA_AV                  0x0002
-
-#define GPREG_0                                 0x570
-#define     GPREG_0__VALUE                              0xffff
-
-#define GPREG_1                                 0x580
-#define     GPREG_1__VALUE                              0xffff
-
-#define GPREG_2                                 0x590
-#define     GPREG_2__VALUE                              0xffff
-
-#define GPREG_3                                 0x5a0
-#define     GPREG_3__VALUE                              0xffff
-
 #define ECC_THRESHOLD                           0x600
 #define     ECC_THRESHOLD__VALUE                        0x03ff
 
@@ -331,69 +311,15 @@
 #define     CHNL_ACTIVE__CHANNEL2                       0x0004
 #define     CHNL_ACTIVE__CHANNEL3                       0x0008
 
-#define ACTIVE_SRC_ID                           0x800
-#define     ACTIVE_SRC_ID__VALUE                        0x00ff
-
-#define PTN_INTR                                        0x810
-#define     PTN_INTR__CONFIG_ERROR                      0x0001
-#define     PTN_INTR__ACCESS_ERROR_BANK0                0x0002
-#define     PTN_INTR__ACCESS_ERROR_BANK1                0x0004
-#define     PTN_INTR__ACCESS_ERROR_BANK2                0x0008
-#define     PTN_INTR__ACCESS_ERROR_BANK3                0x0010
-#define     PTN_INTR__REG_ACCESS_ERROR                  0x0020
-
-#define PTN_INTR_EN                             0x820
-#define     PTN_INTR_EN__CONFIG_ERROR                   0x0001
-#define     PTN_INTR_EN__ACCESS_ERROR_BANK0             0x0002
-#define     PTN_INTR_EN__ACCESS_ERROR_BANK1             0x0004
-#define     PTN_INTR_EN__ACCESS_ERROR_BANK2             0x0008
-#define     PTN_INTR_EN__ACCESS_ERROR_BANK3             0x0010
-#define     PTN_INTR_EN__REG_ACCESS_ERROR               0x0020
-
-#define PERM_SRC_ID(__bank)     (0x830 + ((__bank) * 0x40))
-#define     PERM_SRC_ID__SRCID                          0x00ff
-#define     PERM_SRC_ID__DIRECT_ACCESS_ACTIVE           0x0800
-#define     PERM_SRC_ID__WRITE_ACTIVE                   0x2000
-#define     PERM_SRC_ID__READ_ACTIVE                    0x4000
-#define     PERM_SRC_ID__PARTITION_VALID                0x8000
-
-#define MIN_BLK_ADDR(__bank)    (0x840 + ((__bank) * 0x40))
-#define     MIN_BLK_ADDR__VALUE                         0xffff
-
-#define MAX_BLK_ADDR(__bank)    (0x850 + ((__bank) * 0x40))
-#define     MAX_BLK_ADDR__VALUE                         0xffff
-
-#define MIN_MAX_BANK(__bank)    (0x860 + ((__bank) * 0x40))
-#define     MIN_MAX_BANK__MIN_VALUE                     0x0003
-#define     MIN_MAX_BANK__MAX_VALUE                     0x000c
-
-
-/* ffsdefs.h */
-#define CLEAR 0                 /*use this to clear a field instead of "fail"*/
-#define SET   1                 /*use this to set a field instead of "pass"*/
 #define FAIL 1                  /*failed flag*/
 #define PASS 0                  /*success flag*/
-#define ERR -1                  /*error flag*/
-
-/* lld.h */
-#define GOOD_BLOCK 0
-#define DEFECTIVE_BLOCK 1
-#define READ_ERROR 2
 
 #define CLK_X  5
 #define CLK_MULTI 4
 
-/* KBV - Updated to LNW scratch register address */
-#define SCRATCH_REG_ADDR    CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR
-#define SCRATCH_REG_SIZE    64
-
-#define GLOB_HWCTL_DEFAULT_BLKS    2048
-
 #define SUPPORT_15BITECC        1
 #define SUPPORT_8BITECC         1
 
-#define CUSTOM_CONF_PARAMS      0
-
 #define ONFI_BLOOM_TIME         1
 #define MODE5_WORKAROUND        0
 
@@ -403,31 +329,6 @@
 #define MODE_10    0x08000000
 #define MODE_11    0x0C000000
 
-
-#define DATA_TRANSFER_MODE              0
-#define PROTECTION_PER_BLOCK            1
-#define LOAD_WAIT_COUNT                 2
-#define PROGRAM_WAIT_COUNT              3
-#define ERASE_WAIT_COUNT                4
-#define INT_MONITOR_CYCLE_COUNT         5
-#define READ_BUSY_PIN_ENABLED           6
-#define MULTIPLANE_OPERATION_SUPPORT    7
-#define PRE_FETCH_MODE                  8
-#define CE_DONT_CARE_SUPPORT            9
-#define COPYBACK_SUPPORT                10
-#define CACHE_WRITE_SUPPORT             11
-#define CACHE_READ_SUPPORT              12
-#define NUM_PAGES_IN_BLOCK              13
-#define ECC_ENABLE_SELECT               14
-#define WRITE_ENABLE_2_READ_ENABLE      15
-#define ADDRESS_2_DATA                  16
-#define READ_ENABLE_2_WRITE_ENABLE      17
-#define TWO_ROW_ADDRESS_CYCLES          18
-#define MULTIPLANE_ADDRESS_RESTRICT     19
-#define ACC_CLOCKS                      20
-#define READ_WRITE_ENABLE_LOW_COUNT     21
-#define READ_WRITE_ENABLE_HIGH_COUNT    22
-
 #define ECC_SECTOR_SIZE     512
 
 struct nand_buf {