55 files changed, 1522 insertions, 37 deletions

diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt
new file mode 100644
index 000000000000..aabca4f83402
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/atmel-aic.txt
@@ -0,0 +1,38 @@
+* Advanced Interrupt Controller (AIC)
+
+Required properties:
+- compatible: Should be "atmel,<chip>-aic"
+- interrupt-controller: Identifies the node as an interrupt controller.
+- interrupt-parent: For single AIC system, it is an empty property.
+- #interrupt-cells: The number of cells to define the interrupts. It sould be 2.
+  The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet).
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+      Valid combinations are 1, 2, 3, 4, 8.
+      Default flag for internal sources should be set to 4 (active high).
+- reg: Should contain AIC registers location and length
+
+Examples:
+        /*
+         * AIC
+         */
+        aic: interrupt-controller@fffff000 {
+                compatible = "atmel,at91rm9200-aic";
+                interrupt-controller;
+                interrupt-parent;
+                #interrupt-cells = <2>;
+                reg = <0xfffff000 0x200>;
+        };
+
+        /*
+         * An interrupt generating device that is wired to an AIC.
+         */
+        dma: dma-controller@ffffec00 {
+                compatible = "atmel,at91sam9g45-dma";
+                reg = <0xffffec00 0x200>;
+                interrupts = <21 4>;
+        };
diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
new file mode 100644
index 000000000000..ecc81e368715
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -0,0 +1,92 @@
+Atmel AT91 device tree bindings.
+================================
+
+PIT Timer required properties:
+- compatible: Should be "atmel,at91sam9260-pit"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt for the PIT which is the IRQ line
+  shared across all System Controller members.
+
+TC/TCLIB Timer required properties:
+- compatible: Should be "atmel,<chip>-pit".
+  <chip> can be "at91rm9200" or "at91sam9x5"
+- reg: Should contain registers location and length
+- interrupts: Should contain all interrupts for the TC block
+  Note that you can specify several interrupt cells if the TC
+  block has one interrupt per channel.
+
+Examples:
+
+One interrupt per TC block:
+        tcb0: timer@fff7c000 {
+                compatible = "atmel,at91rm9200-tcb";
+                reg = <0xfff7c000 0x100>;
+                interrupts = <18 4>;
+        };
+
+One interrupt per TC channel in a TC block:
+        tcb1: timer@fffdc000 {
+                compatible = "atmel,at91rm9200-tcb";
+                reg = <0xfffdc000 0x100>;
+                interrupts = <26 4 27 4 28 4>;
+        };
+
+RSTC Reset Controller required properties:
+- compatible: Should be "atmel,<chip>-rstc".
+  <chip> can be "at91sam9260" or "at91sam9g45"
+- reg: Should contain registers location and length
+
+Example:
+
+        rstc@fffffd00 {
+                compatible = "atmel,at91sam9260-rstc";
+                reg = <0xfffffd00 0x10>;
+        };
+
+RAMC SDRAM/DDR Controller required properties:
+- compatible: Should be "atmel,at91sam9260-sdramc",
+                        "atmel,at91sam9g45-ddramc",
+- reg: Should contain registers location and length
+  For at91sam9263 and at91sam9g45 you must specify 2 entries.
+
+Examples:
+
+        ramc0: ramc@ffffe800 {
+                compatible = "atmel,at91sam9g45-ddramc";
+                reg = <0xffffe800 0x200>;
+        };
+
+        ramc0: ramc@ffffe400 {
+                compatible = "atmel,at91sam9g45-ddramc";
+                reg = <0xffffe400 0x200
+                       0xffffe600 0x200>;
+        };
+
+SHDWC Shutdown Controller
+
+required properties:
+- compatible: Should be "atmel,<chip>-shdwc".
+  <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5".
+- reg: Should contain registers location and length
+
+optional properties:
+- atmel,wakeup-mode: String, operation mode of the wakeup mode.
+  Supported values are: "none", "high", "low", "any".
+- atmel,wakeup-counter: Counter on Wake-up 0 (between 0x0 and 0xf).
+
+optional at91sam9260 properties:
+- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up.
+
+optional at91sam9rl properties:
+- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up.
+- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up.
+
+optional at91sam9x5 properties:
+- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up.
+
+Example:
+
+        rstc@fffffd00 {
+                compatible = "atmel,at91sam9260-rstc";
+                reg = <0xfffffd00 0x10>;
+        };
diff --git a/Documentation/devicetree/bindings/arm/atmel-pmc.txt b/Documentation/devicetree/bindings/arm/atmel-pmc.txt
new file mode 100644
index 000000000000..389bed5056e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/atmel-pmc.txt
@@ -0,0 +1,11 @@
+* Power Management Controller (PMC)
+
+Required properties:
+- compatible: Should be "atmel,at91rm9200-pmc"
+- reg: Should contain PMC registers location and length
+
+Examples:
+        pmc: pmc@fffffc00 {
+                compatible = "atmel,at91rm9200-pmc";
+                reg = <0xfffffc00 0x100>;
+        };
diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
new file mode 100644
index 000000000000..6528e215c5fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
@@ -0,0 +1,21 @@
+* Samsung Exynos Power Domains
+
+Exynos processors include support for multiple power domains which are used
+to gate power to one or more peripherals on the processor.
+
+Required Properties:
+- compatiable: should be one of the following.
+    * samsung,exynos4210-pd - for exynos4210 type power domain.
+- reg: physical base address of the controller and length of memory mapped
+    region.
+
+Optional Properties:
+- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off
+    state during boot and remains to be turned-off until explicitly turned-on.
+
+Example:
+
+        lcd0: power-domain-lcd0 {
+                compatible = "samsung,exynos4210-pd";
+                reg = <0x10023C00 0x10>;
+        };
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index 54bdddadf1cf..bfbc771a65f8 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -28,3 +28,25 @@ Required root node properties:
 i.MX6 Quad SABRE Lite Board
 Required root node properties:
     - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
+
+Generic i.MX boards
+-------------------
+
+No iomux setup is done for these boards, so this must have been configured
+by the bootloader for boards to work with the generic bindings.
+
+i.MX27 generic board
+Required root node properties:
+    - compatible = "fsl,imx27";
+
+i.MX51 generic board
+Required root node properties:
+    - compatible = "fsl,imx51";
+
+i.MX53 generic board
+Required root node properties:
+    - compatible = "fsl,imx53";
+
+i.MX6q generic board
+Required root node properties:
+    - compatible = "fsl,imx6q";
diff --git a/Documentation/devicetree/bindings/arm/mrvl.txt b/Documentation/devicetree/bindings/arm/mrvl.txt
new file mode 100644
index 000000000000..d8de933e9d81
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/mrvl.txt
@@ -0,0 +1,6 @@
+Marvell Platforms Device Tree Bindings
+----------------------------------------------------
+
+PXA168 Aspenite Board
+Required root node properties:
+        - compatible = "mrvl,pxa168-aspenite", "mrvl,pxa168";
diff --git a/Documentation/devicetree/bindings/arm/omap/intc.txt b/Documentation/devicetree/bindings/arm/omap/intc.txt
new file mode 100644
index 000000000000..f2583e6ec060
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/intc.txt
@@ -0,0 +1,27 @@
+* OMAP Interrupt Controller
+
+OMAP2/3 are using a TI interrupt controller that can support several
+configurable number of interrupts.
+
+Main node required properties:
+
+- compatible : should be:
+        "ti,omap2-intc"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The type shall be a <u32> and the value shall be 1.
+
+  The cell contains the interrupt number in the range [0-128].
+- ti,intc-size: Number of interrupts handled by the interrupt controller.
+- reg: physical base address and size of the intc registers map.
+
+Example:
+
+        intc: interrupt-controller@1 {
+                compatible = "ti,omap2-intc";
+                interrupt-controller;
+                #interrupt-cells = <1>;
+                ti,intc-size = <96>;
+                reg = <0x48200000 0x1000>;
+        };
+
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index edc618a8aab2..e78e8bccac30 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -41,3 +41,9 @@ Boards:
 
 - OMAP4 PandaBoard : Low cost community board
   compatible = "ti,omap4-panda", "ti,omap4430"
+
+- OMAP3 EVM : Software Developement Board for OMAP35x, AM/DM37x
+  compatible = "ti,omap3-evm", "ti,omap3"
+
+- AM335X EVM : Software Developement Board for AM335x
+  compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3"
diff --git a/Documentation/devicetree/bindings/arm/spear.txt b/Documentation/devicetree/bindings/arm/spear.txt
new file mode 100644
index 000000000000..f8e54f092328
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/spear.txt
@@ -0,0 +1,8 @@
+ST SPEAr Platforms Device Tree Bindings
+---------------------------------------
+
+Boards with the ST SPEAr600 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear600";
diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/emc.txt
new file mode 100644
index 000000000000..09335f8eee00
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/emc.txt
@@ -0,0 +1,100 @@
+Embedded Memory Controller
+
+Properties:
+- name : Should be emc
+- #address-cells : Should be 1
+- #size-cells : Should be 0
+- compatible : Should contain "nvidia,tegra20-emc".
+- reg : Offset and length of the register set for the device
+- nvidia,use-ram-code : If present, the sub-nodes will be addressed
+  and chosen using the ramcode board selector. If omitted, only one
+  set of tables can be present and said tables will be used
+  irrespective of ram-code configuration.
+
+Child device nodes describe the memory settings for different configurations and clock rates.
+
+Example:
+
+        emc@7000f400 {
+                #address-cells = < 1 >;
+                #size-cells = < 0 >;
+                compatible = "nvidia,tegra20-emc";
+                reg = <0x7000f4000 0x200>;
+        }
+
+
+Embedded Memory Controller ram-code table
+
+If the emc node has the nvidia,use-ram-code property present, then the
+next level of nodes below the emc table are used to specify which settings
+apply for which ram-code settings.
+
+If the emc node lacks the nvidia,use-ram-code property, this level is omitted
+and the tables are stored directly under the emc node (see below).
+
+Properties:
+
+- name : Should be emc-tables
+- nvidia,ram-code : the binary representation of the ram-code board strappings
+  for which this node (and children) are valid.
+
+
+
+Embedded Memory Controller configuration table
+
+This is a table containing the EMC register settings for the various
+operating speeds of the memory controller. They are always located as
+subnodes of the emc controller node.
+
+There are two ways of specifying which tables to use:
+
+* The simplest is if there is just one set of tables in the device tree,
+  and they will always be used (based on which frequency is used).
+  This is the preferred method, especially when firmware can fill in
+  this information based on the specific system information and just
+  pass it on to the kernel.
+
+* The slightly more complex one is when more than one memory configuration
+  might exist on the system.  The Tegra20 platform handles this during
+  early boot by selecting one out of possible 4 memory settings based
+  on a 2-pin "ram code" bootstrap setting on the board. The values of
+  these strappings can be read through a register in the SoC, and thus
+  used to select which tables to use.
+
+Properties:
+- name : Should be emc-table
+- compatible : Should contain "nvidia,tegra20-emc-table".
+- reg : either an opaque enumerator to tell different tables apart, or
+  the valid frequency for which the table should be used (in kHz).
+- clock-frequency : the clock frequency for the EMC at which this
+  table should be used (in kHz).
+- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
+  for operation at the 'clock-frequency' setting.
+  The order and contents of the registers are:
+    RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
+    WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
+    PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
+    TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
+    ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
+    ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
+    CFG_CLKTRIM_1, CFG_CLKTRIM_2
+
+                emc-table@166000 {
+                        reg = <166000>;
+                        compatible = "nvidia,tegra20-emc-table";
+                        clock-frequency = < 166000 >;
+                        nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+                                                 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+                                                 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+                                                 0 0 0 0 >;
+                };
+
+                emc-table@333000 {
+                        reg = <333000>;
+                        compatible = "nvidia,tegra20-emc-table";
+                        clock-frequency = < 333000 >;
+                        nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+                                                 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+                                                 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+                                                 0 0 0 0 >;
+                };
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
new file mode 100644
index 000000000000..b5846e21cc2e
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
@@ -0,0 +1,19 @@
+NVIDIA Tegra Power Management Controller (PMC)
+
+Properties:
+- name : Should be pmc
+- compatible : Should contain "nvidia,tegra<chip>-pmc".
+- reg : Offset and length of the register set for the device
+- nvidia,invert-interrupt : If present, inverts the PMU interrupt signal.
+  The PMU is an external Power Management Unit, whose interrupt output
+  signal is fed into the PMC. This signal is optionally inverted, and then
+  fed into the ARM GIC. The PMC is not involved in the detection or
+  handling of this interrupt signal, merely its inversion.
+
+Example:
+
+pmc@7000f400 {
+        compatible = "nvidia,tegra20-pmc";
+        reg = <0x7000e400 0x400>;
+        nvidia,invert-interrupt;
+};
diff --git a/Documentation/devicetree/bindings/arm/twd.txt b/Documentation/devicetree/bindings/arm/twd.txt
new file mode 100644
index 000000000000..75b8610939fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/twd.txt
@@ -0,0 +1,48 @@
+* ARM Timer Watchdog
+
+ARM 11MP, Cortex-A5 and Cortex-A9 are often associated with a per-core
+Timer-Watchdog (aka TWD), which provides both a per-cpu local timer
+and watchdog.
+
+The TWD is usually attached to a GIC to deliver its two per-processor
+interrupts.
+
+** Timer node required properties:
+
+- compatible : Should be one of:
+        "arm,cortex-a9-twd-timer"
+        "arm,cortex-a5-twd-timer"
+        "arm,arm11mp-twd-timer"
+
+- interrupts : One interrupt to each core
+
+- reg : Specify the base address and the size of the TWD timer
+        register window.
+
+Example:
+
+        twd-timer@2c000600 {
+                compatible = "arm,arm11mp-twd-timer"";
+                reg = <0x2c000600 0x20>;
+                interrupts = <1 13 0xf01>;
+        };
+
+** Watchdog node properties:
+
+- compatible : Should be one of:
+        "arm,cortex-a9-twd-wdt"
+        "arm,cortex-a5-twd-wdt"
+        "arm,arm11mp-twd-wdt"
+
+- interrupts : One interrupt to each core
+
+- reg : Specify the base address and the size of the TWD watchdog
+        register window.
+
+Example:
+
+        twd-watchdog@2c000620 {
+                compatible = "arm,arm11mp-twd-wdt";
+                reg = <0x2c000620 0x20>;
+                interrupts = <1 14 0xf01>;
+        };
diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt
new file mode 100644
index 000000000000..ec8b50cbb2e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/vexpress.txt
@@ -0,0 +1,146 @@
+ARM Versatile Express boards family
+-----------------------------------
+
+ARM's Versatile Express platform consists of a motherboard and one
+or more daughterboards (tiles). The motherboard provides a set of
+peripherals. Processor and RAM "live" on the tiles.
+
+The motherboard and each core tile should be described by a separate
+Device Tree source file, with the tile's description including
+the motherboard file using a /include/ directive. As the motherboard
+can be initialized in one of two different configurations ("memory
+maps"), care must be taken to include the correct one.
+
+Required properties in the root node:
+- compatible value:
+        compatible = "arm,vexpress,<model>", "arm,vexpress";
+  where <model> is the full tile model name (as used in the tile's
+    Technical Reference Manual), eg.:
+    - for Coretile Express A5x2 (V2P-CA5s):
+        compatible = "arm,vexpress,v2p-ca5s", "arm,vexpress";
+    - for Coretile Express A9x4 (V2P-CA9):
+        compatible = "arm,vexpress,v2p-ca9", "arm,vexpress";
+  If a tile comes in several variants or can be used in more then one
+  configuration, the compatible value should be:
+        compatible = "arm,vexpress,<model>,<variant>", \
+                                "arm,vexpress,<model>", "arm,vexpress";
+  eg:
+    - Coretile Express A15x2 (V2P-CA15) with Tech Chip 1:
+        compatible = "arm,vexpress,v2p-ca15,tc1", \
+                                "arm,vexpress,v2p-ca15", "arm,vexpress";
+    - LogicTile Express 13MG (V2F-2XV6) running Cortex-A7 (3 cores) SMM:
+        compatible = "arm,vexpress,v2f-2xv6,ca7x3", \
+                                "arm,vexpress,v2f-2xv6", "arm,vexpress";
+
+Optional properties in the root node:
+- tile model name (use name from the tile's Technical Reference
+  Manual, eg. "V2P-CA5s")
+        model = "<model>";
+- tile's HBI number (unique ARM's board model ID, visible on the
+  PCB's silkscreen) in hexadecimal transcription:
+        arm,hbi = <0xhbi>
+  eg:
+  - for Coretile Express A5x2 (V2P-CA5s) HBI-0191:
+        arm,hbi = <0x191>;
+  - Coretile Express A9x4 (V2P-CA9) HBI-0225:
+        arm,hbi = <0x225>;
+
+Top-level standard "cpus" node is required. It must contain a node
+with device_type = "cpu" property for every available core, eg.:
+
+        cpus {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                cpu@0 {
+                        device_type = "cpu";
+                        compatible = "arm,cortex-a5";
+                        reg = <0>;
+                };
+        };
+
+The motherboard description file provides a single "motherboard" node
+using 2 address cells corresponding to the Static Memory Bus used
+between the motherboard and the tile. The first cell defines the Chip
+Select (CS) line number, the second cell address offset within the CS.
+All interrupt lines between the motherboard and the tile are active
+high and are described using single cell.
+
+Optional properties of the "motherboard" node:
+- motherboard's memory map variant:
+        arm,v2m-memory-map = "<name>";
+  where name is one of:
+  - "rs1" - for RS1 map (i.a. peripherals on CS3); this map is also
+            referred to as "ARM Cortex-A Series memory map":
+        arm,v2m-memory-map = "rs1";
+  When this property is missing, the motherboard is using the original
+  memory map (also known as the "Legacy memory map", primarily used
+  with the original CoreTile Express A9x4) with peripherals on CS7.
+
+Motherboard .dtsi files provide a set of labelled peripherals that
+can be used to obtain required phandle in the tile's "aliases" node:
+- UARTs, note that the numbers correspond to the physical connectors
+  on the motherboard's back panel:
+        v2m_serial0, v2m_serial1, v2m_serial2 and v2m_serial3
+- I2C controllers:
+        v2m_i2c_dvi and v2m_i2c_pcie
+- SP804 timers:
+        v2m_timer01 and v2m_timer23
+
+Current Linux implementation requires a "arm,v2m_timer" alias
+pointing at one of the motherboard's SP804 timers, if it is to be
+used as the system timer. This alias should be defined in the
+motherboard files.
+
+The tile description must define "ranges", "interrupt-map-mask" and
+"interrupt-map" properties to translate the motherboard's address
+and interrupt space into one used by the tile's processor.
+
+Abbreviated example:
+
+/dts-v1/;
+
+/ {
+        model = "V2P-CA5s";
+        arm,hbi = <0x225>;
+        compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress";
+        interrupt-parent = <&gic>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        chosen { };
+
+        aliases {
+                serial0 = &v2m_serial0;
+        };
+
+        cpus {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                cpu@0 {
+                        device_type = "cpu";
+                        compatible = "arm,cortex-a5";
+                        reg = <0>;
+                };
+        };
+
+        gic: interrupt-controller@2c001000 {
+                compatible = "arm,cortex-a9-gic";
+                #interrupt-cells = <3>;
+                #address-cells = <0>;
+                interrupt-controller;
+                reg = <0x2c001000 0x1000>,
+                      <0x2c000100 0x100>;
+        };
+
+        motherboard {
+                /* CS0 is visible at 0x08000000 */
+                ranges = <0 0 0x08000000 0x04000000>;
+                interrupt-map-mask = <0 0 63>;
+                /* Active high IRQ 0 is connected to GIC's SPI0 */
+                interrupt-map = <0 0 0 &gic 0 0 4>;
+        };
+};
+
+/include/ "vexpress-v2m-rs1.dtsi"
diff --git a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt
new file mode 100644
index 000000000000..90fa7da525b8
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt
@@ -0,0 +1,30 @@
+* NVIDIA Tegra APB DMA controller
+
+Required properties:
+- compatible: Should be "nvidia,<chip>-apbdma"
+- reg: Should contain DMA registers location and length. This shuld include
+  all of the per-channel registers.
+- interrupts: Should contain all of the per-channel DMA interrupts.
+
+Examples:
+
+apbdma: dma@6000a000 {
+        compatible = "nvidia,tegra20-apbdma";
+        reg = <0x6000a000 0x1200>;
+        interrupts = < 0 136 0x04
+                       0 137 0x04
+                       0 138 0x04
+                       0 139 0x04
+                       0 140 0x04
+                       0 141 0x04
+                       0 142 0x04
+                       0 143 0x04
+                       0 144 0x04
+                       0 145 0x04
+                       0 146 0x04
+                       0 147 0x04
+                       0 148 0x04
+                       0 149 0x04
+                       0 150 0x04
+                       0 151 0x04 >;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/Documentation/devicetree/bindings/gpio/gpio-omap.txt
new file mode 100644
index 000000000000..bff51a2fee1e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-omap.txt
@@ -0,0 +1,36 @@
+OMAP GPIO controller bindings
+
+Required properties:
+- compatible:
+  - "ti,omap2-gpio" for OMAP2 controllers
+  - "ti,omap3-gpio" for OMAP3 controllers
+  - "ti,omap4-gpio" for OMAP4 controllers
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify optional parameters (unused)
+- gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+- interrupt-controller: Mark the device node as an interrupt controller
+  The first cell is the GPIO number.
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+OMAP specific properties:
+- ti,hwmods: Name of the hwmod associated to the GPIO:
+  "gpio<X>", <X> being the 1-based instance number from the HW spec
+
+
+Example:
+
+gpio4: gpio4 {
+    compatible = "ti,omap4-gpio";
+    ti,hwmods = "gpio4";
+    #gpio-cells = <2>;
+    gpio-controller;
+    #interrupt-cells = <2>;
+    interrupt-controller;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt
new file mode 100644
index 000000000000..16695d9cf1e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt
@@ -0,0 +1,23 @@
+twl4030 GPIO controller bindings
+
+Required properties:
+- compatible:
+  - "ti,twl4030-gpio" for twl4030 GPIO controller
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify optional parameters (unused)
+- gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+- interrupt-controller: Mark the device node as an interrupt controller
+  The first cell is the GPIO number.
+  The second cell is not used.
+
+Example:
+
+twl_gpio: gpio {
+    compatible = "ti,twl4030-gpio";
+    #gpio-cells = <2>;
+    gpio-controller;
+    #interrupt-cells = <2>;
+    interrupt-controller;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt
new file mode 100644
index 000000000000..66efc804806a
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt
@@ -0,0 +1,20 @@
+* Atmel GPIO controller (PIO)
+
+Required properties:
+- compatible: "atmel,<chip>-gpio", where <chip> is at91rm9200 or at91sam9x5.
+- reg: Should contain GPIO controller registers location and length
+- interrupts: Should be the port interrupt shared by all the pins.
+- #gpio-cells: Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller: Marks the device node as a GPIO controller.
+
+Example:
+        pioA: gpio@fffff200 {
+                compatible = "atmel,at91rm9200-gpio";
+                reg = <0xfffff200 0x100>;
+                interrupts = <2 4>;
+                #gpio-cells = <2>;
+                gpio-controller;
+        };
+
diff --git a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt
new file mode 100644
index 000000000000..4f8ec947c6bd
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt
@@ -0,0 +1,32 @@
+Device-Tree bindings for i2c gpio driver
+
+Required properties:
+        - compatible = "i2c-gpio";
+        - gpios: sda and scl gpio
+
+
+Optional properties:
+        - i2c-gpio,sda-open-drain: sda as open drain
+        - i2c-gpio,scl-open-drain: scl as open drain
+        - i2c-gpio,scl-output-only: scl as output only
+        - i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform)
+        - i2c-gpio,timeout-ms: timeout to get data
+
+Example nodes:
+
+i2c@0 {
+        compatible = "i2c-gpio";
+        gpios = <&pioA 23 0 /* sda */
+                 &pioA 24 0 /* scl */
+                >;
+        i2c-gpio,sda-open-drain;
+        i2c-gpio,scl-open-drain;
+        i2c-gpio,delay-us = <2>;        /* ~100 kHz */
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        rv3029c2@56 {
+                compatible = "rv3029c2";
+                reg = <0x56>;
+        };
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
index eb4b530d64e1..023c9526e5f8 100644
--- a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
@@ -1,8 +1,40 @@
-NVIDIA Tegra 2 GPIO controller
+NVIDIA Tegra GPIO controller
 
 Required properties:
-- compatible : "nvidia,tegra20-gpio"
+- compatible : "nvidia,tegra<chip>-gpio"
+- reg : Physical base address and length of the controller's registers.
+- interrupts : The interrupt outputs from the controller. For Tegra20,
+  there should be 7 interrupts specified, and for Tegra30, there should
+  be 8 interrupts specified.
 - #gpio-cells : Should be two. The first cell is the pin number and the
   second cell is used to specify optional parameters:
   - bit 0 specifies polarity (0 for normal, 1 for inverted)
 - gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+  The first cell is the GPIO number.
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+      Valid combinations are 1, 2, 3, 4, 8.
+- interrupt-controller : Marks the device node as an interrupt controller.
+
+Example:
+
+gpio: gpio@6000d000 {
+        compatible = "nvidia,tegra20-gpio";
+        reg = < 0x6000d000 0x1000 >;
+        interrupts = < 0 32 0x04
+                       0 33 0x04
+                       0 34 0x04
+                       0 35 0x04
+                       0 55 0x04
+                       0 87 0x04
+                       0 89 0x04 >;
+        #gpio-cells = <2>;
+        gpio-controller;
+        #interrupt-cells = <2>;
+        interrupt-controller;
+};
diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt
index 141087cf3107..fd2bd56e7195 100644
--- a/Documentation/devicetree/bindings/gpio/led.txt
+++ b/Documentation/devicetree/bindings/gpio/led.txt
@@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device.  Each
 node's name represents the name of the corresponding LED.
 
 LED sub-node properties:
-- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
-  for devices" in Documentation/devicetree/booting-without-of.txt.  Active
-  low LEDs should be indicated using flags in the GPIO specifier.
+- gpios :  Should specify the LED's GPIO, see "gpios property" in
+  Documentation/devicetree/gpio.txt.  Active low LEDs should be
+  indicated using flags in the GPIO specifier.
 - label :  (optional) The label for this LED.  If omitted, the label is
   taken from the node name (excluding the unit address).
 - linux,default-trigger :  (optional) This parameter, if present, is a
diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
new file mode 100644
index 000000000000..1e34cfe5ebea
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
@@ -0,0 +1,23 @@
+* Marvell PXA GPIO controller
+
+Required properties:
+- compatible : Should be "mrvl,pxa-gpio" or "mrvl,mmp-gpio"
+- reg : Address and length of the register set for the device
+- interrupts : Should be the port interrupt shared by all gpio pins, if
+- interrupt-name : Should be the name of irq resource.
+  one number.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be one.  It is the pin number.
+
+Example:
+
+        gpio: gpio@d4019000 {
+                compatible = "mrvl,mmp-gpio", "mrvl,pxa-gpio";
+                reg = <0xd4019000 0x1000>;
+                interrupts = <49>, <17>, <18>;
+                interrupt-name = "gpio_mux", "gpio0", "gpio1";
+                gpio-controller;
+                #gpio-cells = <1>;
+                interrupt-controller;
+                #interrupt-cells = <1>;
+      };
diff --git a/Documentation/devicetree/bindings/gpio/sodaville.txt b/Documentation/devicetree/bindings/gpio/sodaville.txt
new file mode 100644
index 000000000000..563eff22b975
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/sodaville.txt
@@ -0,0 +1,48 @@
+GPIO controller on CE4100 / Sodaville SoCs
+==========================================
+
+The bindings for CE4100's GPIO controller match the generic description
+which is covered by the gpio.txt file in this folder.
+
+The only additional property is the intel,muxctl property which holds the
+value which is written into the MUXCNTL register.
+
+There is no compatible property for now because the driver is probed via
+PCI id (vendor 0x8086 device 0x2e67).
+
+The interrupt specifier consists of two cells encoded as follows:
+ - <1st cell>: The interrupt-number that identifies the interrupt source.
+ - <2nd cell>: The level-sense information, encoded as follows:
+                4 - active high level-sensitive
+                8 - active low level-sensitive
+
+Example of the GPIO device and one user:
+
+        pcigpio: gpio@b,1 {
+                        /* two cells for GPIO and interrupt */
+                        #gpio-cells = <2>;
+                        #interrupt-cells = <2>;
+                        compatible = "pci8086,2e67.2",
+                                           "pci8086,2e67",
+                                           "pciclassff0000",
+                                           "pciclassff00";
+
+                        reg = <0x15900 0x0 0x0 0x0 0x0>;
+                        /* Interrupt line of the gpio device */
+                        interrupts = <15 1>;
+                        /* It is an interrupt and GPIO controller itself */
+                        interrupt-controller;
+                        gpio-controller;
+                        intel,muxctl = <0>;
+        };
+
+        testuser@20 {
+                        compatible = "example,testuser";
+                        /* User the 11th GPIO line as an active high triggered
+                         * level interrupt
+                         */
+                        interrupts = <11 8>;
+                        interrupt-parent = <&pcigpio>;
+                        /* Use this GPIO also with the gpio functions */
+                        gpios = <&pcigpio 11 0>;
+        };
diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt
new file mode 100644
index 000000000000..071eb3caae91
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt
@@ -0,0 +1,37 @@
+* I2C
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "mrvl,mmp-twsi" where CHIP is the name of a
+   compatible processor, e.g. pxa168, pxa910, mmp2, mmp3.
+   For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required
+   as shown in the example below.
+
+Recommended properties :
+
+ - interrupts : <a b> where a is the interrupt number and b is a
+   field that represents an encoding of the sense and level
+   information for the interrupt.  This should be encoded based on
+   the information in section 2) depending on the type of interrupt
+   controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+   services interrupts for this device.
+ - mrvl,i2c-polling : Disable interrupt of i2c controller. Polling
+   status register of i2c controller instead.
+ - mrvl,i2c-fast-mode : Enable fast mode of i2c controller.
+
+Examples:
+        twsi1: i2c@d4011000 {
+                compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c";
+                reg = <0xd4011000 0x1000>;
+                interrupts = <7>;
+                mrvl,i2c-fast-mode;
+        };
+        
+        twsi2: i2c@d4025000 {
+                compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c";
+                reg = <0xd4025000 0x1000>;
+                interrupts = <58>;
+        };
+
diff --git a/Documentation/devicetree/bindings/i2c/sirf-i2c.txt b/Documentation/devicetree/bindings/i2c/sirf-i2c.txt
new file mode 100644
index 000000000000..7baf9e133fa8
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/sirf-i2c.txt
@@ -0,0 +1,19 @@
+I2C for SiRFprimaII platforms
+
+Required properties :
+- compatible : Must be "sirf,prima2-i2c"
+- reg: physical base address of the controller and length of memory mapped
+     region.
+- interrupts: interrupt number to the cpu.
+
+Optional properties:
+- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
+  The absence of the propoerty indicates the default frequency 100 kHz.
+
+Examples :
+
+i2c0: i2c@b00e0000 {
+    compatible = "sirf,prima2-i2c";
+    reg = <0xb00e0000 0x10000>;
+    interrupts = <24>;
+};
diff --git a/Documentation/devicetree/bindings/input/matrix-keymap.txt b/Documentation/devicetree/bindings/input/matrix-keymap.txt
new file mode 100644
index 000000000000..3cd8b98ccd2d
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/matrix-keymap.txt
@@ -0,0 +1,19 @@
+A simple common binding for matrix-connected key boards. Currently targeted at
+defining the keys in the scope of linux key codes since that is a stable and
+standardized interface at this time.
+
+Required properties:
+- linux,keymap: an array of packed 1-cell entries containing the equivalent
+  of row, column and linux key-code. The 32-bit big endian cell is packed
+  as:
+        row << 24 | column << 16 | key-code
+
+Optional properties:
+Some users of this binding might choose to specify secondary keymaps for
+cases where there is a modifier key such as a Fn key. Proposed names
+for said properties are "linux,fn-keymap" or with another descriptive
+word for the modifier other from "Fn".
+
+Example:
+        linux,keymap = < 0x00030012
+                         0x0102003a >;
diff --git a/Documentation/devicetree/bindings/input/tegra-kbc.txt b/Documentation/devicetree/bindings/input/tegra-kbc.txt
index 5ecfa99089b4..72683be6de35 100644
--- a/Documentation/devicetree/bindings/input/tegra-kbc.txt
+++ b/Documentation/devicetree/bindings/input/tegra-kbc.txt
@@ -3,16 +3,21 @@
 Required properties:
 - compatible: "nvidia,tegra20-kbc"
 
-Optional properties:
-- debounce-delay: delay in milliseconds per row scan for debouncing
-- repeat-delay: delay in milliseconds before repeat starts
-- ghost-filter: enable ghost filtering for this device
-- wakeup-source: configure keyboard as a wakeup source for suspend/resume
+Optional properties, in addition to those specified by the shared
+matrix-keyboard bindings:
+
+- linux,fn-keymap: a second keymap, same specification as the
+  matrix-keyboard-controller spec but to be used when the KEY_FN modifier
+  key is pressed.
+- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing
+- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts
+- nvidia,ghost-filter: enable ghost filtering for this device
+- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume
 
 Example:
 
 keyboard: keyboard {
         compatible = "nvidia,tegra20-kbc";
         reg = <0x7000e200 0x100>;
-        ghost-filter;
+        nvidia,ghost-filter;
 };
diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
new file mode 100644
index 000000000000..dbd4368ab8cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
@@ -0,0 +1,33 @@
+* TI Highspeed MMC host controller for OMAP
+
+The Highspeed MMC Host Controller on TI OMAP family
+provides an interface for MMC, SD, and SDIO types of memory cards.
+
+Required properties:
+- compatible:
+ Should be "ti,omap2-hsmmc", for OMAP2 controllers
+ Should be "ti,omap3-hsmmc", for OMAP3 controllers
+ Should be "ti,omap4-hsmmc", for OMAP4 controllers
+- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1
+- reg : should contain hsmmc registers location and length
+
+Optional properties:
+ti,dual-volt: boolean, supports dual voltage cards
+<supply-name>-supply: phandle to the regulator device tree node
+"supply-name" examples are "vmmc", "vmmc_aux" etc
+ti,bus-width: Number of data lines, default assumed is 1 if the property is missing.
+cd-gpios: GPIOs for card detection
+wp-gpios: GPIOs for write protection
+ti,non-removable: non-removable slot (like eMMC)
+ti,needs-special-reset: Requires a special softreset sequence
+
+Example:
+        mmc1: mmc@0x4809c000 {
+                compatible = "ti,omap4-hsmmc";
+                reg = <0x4809c000 0x400>;
+                ti,hwmods = "mmc1";
+                ti,dual-volt;
+                ti,bus-width = <4>;
+                vmmc-supply = <&vmmc>; /* phandle to regulator node */
+                ti,non-removable;
+        };
diff --git a/Documentation/devicetree/bindings/mtd/arm-versatile.txt b/Documentation/devicetree/bindings/mtd/arm-versatile.txt
index 476845db94d0..beace4b89daa 100644
--- a/Documentation/devicetree/bindings/mtd/arm-versatile.txt
+++ b/Documentation/devicetree/bindings/mtd/arm-versatile.txt
@@ -4,5 +4,5 @@ Required properties:
 - compatible : must be "arm,versatile-flash";
 - bank-width : width in bytes of flash interface.
 
-Optional properties:
-- Subnode partition map from mtd flash binding
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
diff --git a/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt
index ef66ddd01da0..1889a4db5b7c 100644
--- a/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt
+++ b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt
@@ -3,6 +3,9 @@
 Required properties:
 - compatible : "atmel,<model>", "atmel,<series>", "atmel,dataflash".
 
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
 Example:
 
 flash@1 {
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
new file mode 100644
index 000000000000..a20069502f5a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -0,0 +1,41 @@
+Atmel NAND flash
+
+Required properties:
+- compatible : "atmel,at91rm9200-nand".
+- reg : should specify localbus address and size used for the chip,
+        and if availlable the ECC.
+- atmel,nand-addr-offset : offset for the address latch.
+- atmel,nand-cmd-offset : offset for the command latch.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+
+- gpios : specifies the gpio pins to control the NAND device. detect is an
+  optional gpio and may be set to 0 if not present.
+
+Optional properties:
+- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default.
+  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
+  "soft_bch".
+- nand-bus-width : 8 or 16 bus width if not present 8
+- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
+
+Examples:
+nand0: nand@40000000,0 {
+        compatible = "atmel,at91rm9200-nand";
+        #address-cells = <1>;
+        #size-cells = <1>;
+        reg = <0x40000000 0x10000000
+               0xffffe800 0x200
+              >;
+        atmel,nand-addr-offset = <21>;  /* ale */
+        atmel,nand-cmd-offset = <22>;   /* cle */
+        nand-on-flash-bbt;
+        nand-ecc-mode = "soft";
+        gpios = <&pioC 13 0     /* rdy */
+                 &pioC 14 0     /* nce */
+                 0              /* cd */
+                >;
+        partition@0 {
+                ...
+        };
+};
diff --git a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt
index 00f1f546b32e..fce4894f5a98 100644
--- a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt
@@ -19,6 +19,10 @@ Optional properties:
         read registers (tR). Required if property "gpios" is not used
         (R/B# pins not connected).
 
+Each flash chip described may optionally contain additional sub-nodes
+describing partitions of the address space. See partition.txt for more
+detail.
+
 Examples:
 
 upm@1,0 {
diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
new file mode 100644
index 000000000000..e2c663b354d2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
@@ -0,0 +1,33 @@
+* FSMC NAND
+
+Required properties:
+- compatible : "st,spear600-fsmc-nand"
+- reg : Address range of the mtd chip
+- reg-names: Should contain the reg names "fsmc_regs" and "nand_data"
+- st,ale-off : Chip specific offset to ALE
+- st,cle-off : Chip specific offset to CLE
+
+Optional properties:
+- bank-width : Width (in bytes) of the device.  If not present, the width
+  defaults to 1 byte
+- nand-skip-bbtscan: Indicates the the BBT scanning should be skipped
+
+Example:
+
+        fsmc: flash@d1800000 {
+                compatible = "st,spear600-fsmc-nand";
+                #address-cells = <1>;
+                #size-cells = <1>;
+                reg = <0xd1800000 0x1000        /* FSMC Register */
+                       0xd2000000 0x4000>;      /* NAND Base */
+                reg-names = "fsmc_regs", "nand_data";
+                st,ale-off = <0x20000>;
+                st,cle-off = <0x10000>;
+
+                bank-width = <1>;
+                nand-skip-bbtscan;
+
+                partition@0 {
+                        ...
+                };
+        };
diff --git a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
index 719f4dc58df7..36ef07d3c90f 100644
--- a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
@@ -25,6 +25,9 @@ Optional properties:
   GPIO state and before and after command byte writes, this register will be
   read to ensure that the GPIO accesses have completed.
 
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
 Examples:
 
 gpio-nand@1,0 {
diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
index 80152cb567d9..a63c2bd7de2b 100644
--- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
@@ -23,27 +23,8 @@ are defined:
  - vendor-id : Contains the flash chip's vendor id (1 byte).
  - device-id : Contains the flash chip's device id (1 byte).
 
-In addition to the information on the mtd bank itself, the
-device tree may optionally contain additional information
-describing partitions of the address space.  This can be
-used on platforms which have strong conventions about which
-portions of a flash are used for what purposes, but which don't
-use an on-flash partition table such as RedBoot.
-
-Each partition is represented as a sub-node of the mtd device.
-Each node's name represents the name of the corresponding
-partition of the mtd device.
-
-Flash partitions
- - reg : The partition's offset and size within the mtd bank.
- - label : (optional) The label / name for this partition.
-   If omitted, the label is taken from the node name (excluding
-   the unit address).
- - read-only : (optional) This parameter, if present, is a hint to
-   Linux that this partition should only be mounted
-   read-only.  This is usually used for flash partitions
-   containing early-boot firmware images or data which should not
-   be clobbered.
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt
new file mode 100644
index 000000000000..03855c8c492a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/nand.txt
@@ -0,0 +1,7 @@
+* MTD generic binding
+
+- nand-ecc-mode : String, operation mode of the NAND ecc mode.
+  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
+  "soft_bch".
+- nand-bus-width : 8 or 16 bus width if not present 8
+- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt
new file mode 100644
index 000000000000..f114ce1657c2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/partition.txt
@@ -0,0 +1,38 @@
+Representing flash partitions in devicetree
+
+Partitions can be represented by sub-nodes of an mtd device. This can be used
+on platforms which have strong conventions about which portions of a flash are
+used for what purposes, but which don't use an on-flash partition table such
+as RedBoot.
+
+#address-cells & #size-cells must both be present in the mtd device and be
+equal to 1.
+
+Required properties:
+- reg : The partition's offset and size within the mtd bank.
+
+Optional properties:
+- label : The label / name for this partition.  If omitted, the label is taken
+  from the node name (excluding the unit address).
+- read-only : This parameter, if present, is a hint to Linux that this
+  partition should only be mounted read-only. This is usually used for flash
+  partitions containing early-boot firmware images or data which should not be
+  clobbered.
+
+Examples:
+
+
+flash@0 {
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        partition@0 {
+                label = "u-boot";
+                reg = <0x0000000 0x100000>;
+                read-only;
+        };
+
+        uimage@100000 {
+                reg = <0x0100000 0x200000>;
+        };
+];
diff --git a/Documentation/devicetree/bindings/mtd/spear_smi.txt b/Documentation/devicetree/bindings/mtd/spear_smi.txt
new file mode 100644
index 000000000000..7248aadd89e4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/spear_smi.txt
@@ -0,0 +1,31 @@
+* SPEAr SMI
+
+Required properties:
+- compatible : "st,spear600-smi"
+- reg : Address range of the mtd chip
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the STMMAC interrupts
+- clock-rate : Functional clock rate of SMI in Hz
+
+Optional properties:
+- st,smi-fast-mode : Flash supports read in fast mode
+
+Example:
+
+        smi: flash@fc000000 {
+                compatible = "st,spear600-smi";
+                #address-cells = <1>;
+                #size-cells = <1>;
+                reg = <0xfc000000 0x1000>;
+                interrupt-parent = <&vic1>;
+                interrupts = <12>;
+                clock-rate = <50000000>;        /* 50MHz */
+
+                flash@f8000000 {
+                        st,smi-fast-mode;
+                        ...
+                };
+        };
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
new file mode 100644
index 000000000000..1f62623f8c3f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -0,0 +1,28 @@
+* STMicroelectronics 10/100/1000 Ethernet driver (GMAC)
+
+Required properties:
+- compatible: Should be "st,spear600-gmac"
+- reg: Address and length of the register set for the device
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the STMMAC interrupts
+- interrupt-names: Should contain the interrupt names "macirq"
+  "eth_wake_irq" if this interrupt is supported in the "interrupts"
+  property
+- phy-mode: String, operation mode of the PHY interface.
+  Supported values are: "mii", "rmii", "gmii", "rgmii".
+
+Optional properties:
+- mac-address: 6 bytes, mac address
+
+Examples:
+
+        gmac0: ethernet@e0800000 {
+                compatible = "st,spear600-gmac";
+                reg = <0xe0800000 0x8000>;
+                interrupt-parent = <&vic1>;
+                interrupts = <24 23>;
+                interrupt-names = "macirq", "eth_wake_irq";
+                mac-address = [000000000000]; /* Filled in by U-Boot */
+                phy-mode = "gmii";
+        };
diff --git a/Documentation/devicetree/bindings/power_supply/max17042_battery.txt b/Documentation/devicetree/bindings/power_supply/max17042_battery.txt
new file mode 100644
index 000000000000..5bc9b685cf8a
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/max17042_battery.txt
@@ -0,0 +1,18 @@
+max17042_battery
+~~~~~~~~~~~~~~~~
+
+Required properties :
+ - compatible : "maxim,max17042"
+
+Optional properties :
+ - maxim,rsns-microohm : Resistance of rsns resistor in micro Ohms
+                         (datasheet-recommended value is 10000).
+   Defining this property enables current-sense functionality.
+
+Example:
+
+        battery-charger@36 {
+                compatible = "maxim,max17042";
+                reg = <0x36>;
+                maxim,rsns-microohm = <10000>;
+        };
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt
new file mode 100644
index 000000000000..bc8ded641ab6
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic-msgr.txt
@@ -0,0 +1,63 @@
+* FSL MPIC Message Registers
+
+This binding specifies what properties must be available in the device tree
+representation of the message register blocks found in some FSL MPIC
+implementations.
+
+Required properties:
+
+    - compatible: Specifies the compatibility list for the message register
+      block.  The type shall be <string-list> and the value shall be of the form
+      "fsl,mpic-v<version>-msgr", where <version> is the version number of
+      the MPIC containing the message registers.
+
+    - reg: Specifies the base physical address(s) and size(s) of the
+      message register block's addressable register space.  The type shall be
+      <prop-encoded-array>.
+
+    - interrupts: Specifies a list of interrupt-specifiers which are available
+      for receiving interrupts. Interrupt-specifier consists of two cells: first
+      cell is interrupt-number and second cell is level-sense. The type shall be
+      <prop-encoded-array>.
+
+Optional properties:
+
+    - mpic-msgr-receive-mask: Specifies what registers in the containing block
+      are allowed to receive interrupts. The value is a bit mask where a set
+      bit at bit 'n' indicates that message register 'n' can receive interrupts.
+      Note that "bit 'n'" is numbered from LSB for PPC hardware. The type shall
+      be <u32>. If not present, then all of the message registers in the block
+      are available.
+
+Aliases:
+
+    An alias should be created for every message register block.  They are not
+    required, though.  However, a particular implementation of this binding
+    may require aliases to be present.  Aliases are of the form
+    'mpic-msgr-block<n>', where <n> is an integer specifying the block's number.
+    Numbers shall start at 0.
+
+Example:
+
+        aliases {
+                mpic-msgr-block0 = &mpic_msgr_block0;
+                mpic-msgr-block1 = &mpic_msgr_block1;
+        };
+
+        mpic_msgr_block0: mpic-msgr-block@41400 {
+                compatible = "fsl,mpic-v3.1-msgr";
+                reg = <0x41400 0x200>;
+                // Message registers 0 and 2 in this block can receive interrupts on
+                // sources 0xb0 and 0xb2, respectively.
+                interrupts = <0xb0 2 0xb2 2>;
+                mpic-msgr-receive-mask = <0x5>;
+        };
+
+        mpic_msgr_block1: mpic-msgr-block@42400 {
+                compatible = "fsl,mpic-v3.1-msgr";
+                reg = <0x42400 0x200>;
+                // Message registers 0 and 2 in this block can receive interrupts on
+                // sources 0xb4 and 0xb6, respectively.
+                interrupts = <0xb4 2 0xb6 2>;
+                mpic-msgr-receive-mask = <0x5>;
+        };
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt
index 2cf38bd841fd..dc5744636a57 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt
+++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt
@@ -56,7 +56,27 @@ PROPERTIES
           to the client.  The presence of this property also mandates
           that any initialization related to interrupt sources shall
           be limited to sources explicitly referenced in the device tree.
-       
+
+  - big-endian
+      Usage: optional
+      Value type: <empty>
+          If present the MPIC will be assumed to be big-endian.  Some
+          device-trees omit this property on MPIC nodes even when the MPIC is
+          in fact big-endian, so certain boards override this property.
+
+  - single-cpu-affinity
+      Usage: optional
+      Value type: <empty>
+          If present the MPIC will be assumed to only be able to route
+          non-IPI interrupts to a single CPU at a time (EG: Freescale MPIC).
+
+  - last-interrupt-source
+      Usage: optional
+      Value type: <u32>
+          Some MPICs do not correctly report the number of hardware sources
+          in the global feature registers.  If specified, this field will
+          override the value read from MPIC_GREG_FEATURE_LAST_SRC.
+
 INTERRUPT SPECIFIER DEFINITION
 
   Interrupt specifiers consists of 4 cells encoded as
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt
index 5d586e1ccaf5..5693877ab377 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt
+++ b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt
@@ -6,8 +6,10 @@ Required properties:
   etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on
   the parent type.
 
-- reg : should contain the address and the length of the shared message
-  interrupt register set.
+- reg : It may contain one or two regions. The first region should contain
+  the address and the length of the shared message interrupt register set.
+  The second region should contain the address of aliased MSIIR register for
+  platforms that have such an alias.
 
 - msi-available-ranges: use <start count> style section to define which
   msi interrupt can be used in the 256 msi interrupts. This property is
diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt
new file mode 100644
index 000000000000..357758cb6e92
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt
@@ -0,0 +1,29 @@
+Anatop Voltage regulators
+
+Required properties:
+- compatible: Must be "fsl,anatop-regulator"
+- anatop-reg-offset: Anatop MFD register offset
+- anatop-vol-bit-shift: Bit shift for the register
+- anatop-vol-bit-width: Number of bits used in the register
+- anatop-min-bit-val: Minimum value of this register
+- anatop-min-voltage: Minimum voltage of this regulator
+- anatop-max-voltage: Maximum voltage of this regulator
+
+Any property defined as part of the core regulator
+binding, defined in regulator.txt, can also be used.
+
+Example:
+
+        regulator-vddpu {
+                compatible = "fsl,anatop-regulator";
+                regulator-name = "vddpu";
+                regulator-min-microvolt = <725000>;
+                regulator-max-microvolt = <1300000>;
+                regulator-always-on;
+                anatop-reg-offset = <0x140>;
+                anatop-vol-bit-shift = <9>;
+                anatop-vol-bit-width = <5>;
+                anatop-min-bit-val = <1>;
+                anatop-min-voltage = <725000>;
+                anatop-max-voltage = <1300000>;
+        };
diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt
new file mode 100644
index 000000000000..0c3395d55ac1
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt
@@ -0,0 +1,68 @@
+TWL family of regulators
+
+Required properties:
+For twl6030 regulators/LDOs
+- compatible:
+  - "ti,twl6030-vaux1" for VAUX1 LDO
+  - "ti,twl6030-vaux2" for VAUX2 LDO
+  - "ti,twl6030-vaux3" for VAUX3 LDO
+  - "ti,twl6030-vmmc" for VMMC LDO
+  - "ti,twl6030-vpp" for VPP LDO
+  - "ti,twl6030-vusim" for VUSIM LDO
+  - "ti,twl6030-vana" for VANA LDO
+  - "ti,twl6030-vcxio" for VCXIO LDO
+  - "ti,twl6030-vdac" for VDAC LDO
+  - "ti,twl6030-vusb" for VUSB LDO
+  - "ti,twl6030-v1v8" for V1V8 LDO
+  - "ti,twl6030-v2v1" for V2V1 LDO
+  - "ti,twl6030-clk32kg" for CLK32KG RESOURCE
+  - "ti,twl6030-vdd1" for VDD1 SMPS
+  - "ti,twl6030-vdd2" for VDD2 SMPS
+  - "ti,twl6030-vdd3" for VDD3 SMPS
+For twl6025 regulators/LDOs
+- compatible:
+  - "ti,twl6025-ldo1" for LDO1 LDO
+  - "ti,twl6025-ldo2" for LDO2 LDO
+  - "ti,twl6025-ldo3" for LDO3 LDO
+  - "ti,twl6025-ldo4" for LDO4 LDO
+  - "ti,twl6025-ldo5" for LDO5 LDO
+  - "ti,twl6025-ldo6" for LDO6 LDO
+  - "ti,twl6025-ldo7" for LDO7 LDO
+  - "ti,twl6025-ldoln" for LDOLN LDO
+  - "ti,twl6025-ldousb" for LDOUSB LDO
+  - "ti,twl6025-smps3" for SMPS3 SMPS
+  - "ti,twl6025-smps4" for SMPS4 SMPS
+  - "ti,twl6025-vio" for VIO SMPS
+For twl4030 regulators/LDOs
+- compatible:
+  - "ti,twl4030-vaux1" for VAUX1 LDO
+  - "ti,twl4030-vaux2" for VAUX2 LDO
+  - "ti,twl5030-vaux2" for VAUX2 LDO
+  - "ti,twl4030-vaux3" for VAUX3 LDO
+  - "ti,twl4030-vaux4" for VAUX4 LDO
+  - "ti,twl4030-vmmc1" for VMMC1 LDO
+  - "ti,twl4030-vmmc2" for VMMC2 LDO
+  - "ti,twl4030-vpll1" for VPLL1 LDO
+  - "ti,twl4030-vpll2" for VPLL2 LDO
+  - "ti,twl4030-vsim" for VSIM LDO
+  - "ti,twl4030-vdac" for VDAC LDO
+  - "ti,twl4030-vintana2" for VINTANA2 LDO
+  - "ti,twl4030-vio" for VIO LDO
+  - "ti,twl4030-vdd1" for VDD1 SMPS
+  - "ti,twl4030-vdd2" for VDD2 SMPS
+  - "ti,twl4030-vintana1" for VINTANA1 LDO
+  - "ti,twl4030-vintdig" for VINTDIG LDO
+  - "ti,twl4030-vusb1v5" for VUSB1V5 LDO
+  - "ti,twl4030-vusb1v8" for VUSB1V8 LDO
+  - "ti,twl4030-vusb3v1" for VUSB3V1 LDO
+
+Optional properties:
+- Any optional property defined in bindings/regulator/regulator.txt
+
+Example:
+
+        xyz: regulator@0 {
+                compatible = "ti,twl6030-vaux1";
+                regulator-min-microvolt  = <1000000>;
+                regulator-max-microvolt  = <3000000>;
+        };
diff --git a/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt
new file mode 100644
index 000000000000..0cda19ad4859
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt
@@ -0,0 +1,17 @@
+* Marvell Real Time Clock controller
+
+Required properties:
+- compatible: should be "mrvl,sa1100-rtc"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: Should be two. The first interrupt number is the rtc alarm
+  interrupt and the second interrupt number is the rtc hz interrupt.
+- interrupt-names: Assign name of irq resource.
+
+Example:
+        rtc: rtc@d4010000 {
+                compatible = "mrvl,mmp-rtc";
+                reg = <0xd4010000 0x1000>;
+                interrupts = <5>, <6>;
+                interrupt-name = "rtc 1Hz", "rtc alarm";
+        };
diff --git a/Documentation/devicetree/bindings/serial/mrvl-serial.txt b/Documentation/devicetree/bindings/serial/mrvl-serial.txt
new file mode 100644
index 000000000000..d744340de887
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/mrvl-serial.txt
@@ -0,0 +1,4 @@
+PXA UART controller
+
+Required properties:
+- compatible : should be "mrvl,mmp-uart" or "mrvl,pxa-uart".
diff --git a/Documentation/devicetree/bindings/sound/alc5632.txt b/Documentation/devicetree/bindings/sound/alc5632.txt
new file mode 100644
index 000000000000..8608f747dcfe
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/alc5632.txt
@@ -0,0 +1,24 @@
+ALC5632 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "realtek,alc5632"
+
+  - reg : the I2C address of the device.
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+
+  - #gpio-cells : Should be two. The first cell is the pin number and the
+    second cell is used to specify optional parameters (currently unused).
+
+Example:
+
+alc5632: alc5632@1e {
+        compatible = "realtek,alc5632";
+        reg = <0x1a>;
+
+        gpio-controller;
+        #gpio-cells = <2>;
+};
diff --git a/Documentation/devicetree/bindings/sound/imx-audmux.txt b/Documentation/devicetree/bindings/sound/imx-audmux.txt
new file mode 100644
index 000000000000..215aa9817213
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/imx-audmux.txt
@@ -0,0 +1,13 @@
+Freescale Digital Audio Mux (AUDMUX) device
+
+Required properties:
+- compatible : "fsl,imx21-audmux" for AUDMUX version firstly used on i.MX21,
+  or "fsl,imx31-audmux" for the version firstly used on i.MX31.
+- reg : Should contain AUDMUX registers location and length
+
+Example:
+
+audmux@021d8000 {
+        compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux";
+        reg = <0x021d8000 0x4000>;
+};
diff --git a/Documentation/devicetree/bindings/sound/soc/codecs/fsl-sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt
index 2c3cd413f042..2c3cd413f042 100644
--- a/Documentation/devicetree/bindings/sound/soc/codecs/fsl-sgtl5000.txt
+++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt
diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt b/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt
new file mode 100644
index 000000000000..b77a97c9101e
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt
@@ -0,0 +1,59 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-alc5632"
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the ALC5632's pins:
+
+  ALC5632 pins:
+
+  * SPK_OUTP
+  * SPK_OUTN
+  * HP_OUT_L
+  * HP_OUT_R
+  * AUX_OUT_P
+  * AUX_OUT_N
+  * LINE_IN_L
+  * LINE_IN_R
+  * PHONE_P
+  * PHONE_N
+  * MIC1_P
+  * MIC1_N
+  * MIC2_P
+  * MIC2_N
+  * MICBIAS1
+  * DMICDAT
+
+  Board connectors:
+
+  * Headset Stereophone
+  * Int Spk
+  * Headset Mic
+  * Digital Mic
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller
+- nvidia,audio-codec : The phandle of the ALC5632 audio codec
+
+Example:
+
+sound {
+        compatible = "nvidia,tegra-audio-alc5632-paz00",
+                                 "nvidia,tegra-audio-alc5632";
+
+        nvidia,model = "Compal PAZ00";
+
+        nvidia,audio-routing =
+                                "Int Spk", "SPK_OUTP",
+                                "Int Spk", "SPK_OUTN",
+                                "Headset Mic","MICBIAS1",
+                                "MIC1_N", "Headset Mic",
+                                "MIC1_P", "Headset Mic",
+                                "Headset Stereophone", "HP_OUT_R",
+                                "Headset Stereophone", "HP_OUT_L";
+
+        nvidia,i2s-controller = <&tegra_i2s1>;
+        nvidia,audio-codec = <&alc5632>;
+};
diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt
new file mode 100644
index 000000000000..81df374adbb9
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/omap-spi.txt
@@ -0,0 +1,20 @@
+OMAP2+ McSPI device
+
+Required properties:
+- compatible :
+  - "ti,omap2-spi" for OMAP2 & OMAP3.
+  - "ti,omap4-spi" for OMAP4+.
+- ti,spi-num-cs : Number of chipselect supported  by the instance.
+- ti,hwmods: Name of the hwmod associated to the McSPI
+
+
+Example:
+
+mcspi1: mcspi@1 {
+    #address-cells = <1>;
+    #size-cells = <0>;
+    compatible = "ti,omap4-mcspi";
+    ti,hwmods = "mcspi1";
+    ti,spi-num-cs = <4>;
+};
+
diff --git a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt
new file mode 100644
index 000000000000..6588b6950a7f
--- /dev/null
+++ b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt
@@ -0,0 +1,14 @@
+* Energymicro efm32 UART
+
+Required properties:
+- compatible : Should be "efm32,uart"
+- reg : Address and length of the register set
+- interrupts : Should contain uart interrupt
+
+Example:
+
+uart@0x4000c400 {
+        compatible = "efm32,uart";
+        reg = <0x4000c400 0x400>;
+        interrupts = <15>;
+};
diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt
new file mode 100644
index 000000000000..60bd2150a3e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt
@@ -0,0 +1,49 @@
+Atmel SOC USB controllers
+
+OHCI
+
+Required properties:
+ - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers
+   used in host mode.
+ - num-ports: Number of ports.
+ - atmel,vbus-gpio: If present, specifies a gpio that needs to be
+   activated for the bus to be powered.
+ - atmel,oc-gpio: If present, specifies a gpio that needs to be
+   activated for the overcurrent detection.
+
+usb0: ohci@00500000 {
+        compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+        reg = <0x00500000 0x100000>;
+        interrupts = <20 4>;
+        num-ports = <2>;
+};
+
+EHCI
+
+Required properties:
+ - compatible: Should be "atmel,at91sam9g45-ehci" for USB controllers
+   used in host mode.
+
+usb1: ehci@00800000 {
+        compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
+        reg = <0x00800000 0x100000>;
+        interrupts = <22 4>;
+};
+
+AT91 USB device controller
+
+Required properties:
+ - compatible: Should be "atmel,at91rm9200-udc"
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain macb interrupt
+
+Optional properties:
+ - atmel,vbus-gpio: If present, specifies a gpio that needs to be
+   activated for the bus to be powered.
+
+usb1: gadget@fffa4000 {
+        compatible = "atmel,at91rm9200-udc";
+        reg = <0xfffa4000 0x4000>;
+        interrupts = <10 4>;
+        atmel,vbus-gpio = <&pioC 5 0>;
+};
diff --git a/Documentation/devicetree/bindings/usb/tegra-usb.txt b/Documentation/devicetree/bindings/usb/tegra-usb.txt
index 035d63d5646d..007005ddbe12 100644
--- a/Documentation/devicetree/bindings/usb/tegra-usb.txt
+++ b/Documentation/devicetree/bindings/usb/tegra-usb.txt
@@ -11,3 +11,16 @@ Required properties :
  - phy_type : Should be one of "ulpi" or "utmi".
  - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
    activated for the bus to be powered.
+
+Optional properties:
+  - dr_mode : dual role mode. Indicates the working mode for
+   nvidia,tegra20-ehci compatible controllers.  Can be "host", "peripheral",
+   or "otg".  Default to "host" if not defined for backward compatibility.
+      host means this is a host controller
+      peripheral means it is device controller
+      otg means it can operate as either ("on the go")
+  - nvidia,has-legacy-mode : boolean indicates whether this controller can
+    operate in legacy mode (as APX 2500 / 2600). In legacy mode some
+    registers are accessed through the APB_MISC base address instead of
+    the USB controller. Since this is a legacy issue it probably does not
+    warrant a compatible string of its own.
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index ecc6a6cd26c1..82ac057a24a9 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -30,9 +30,11 @@ national	National Semiconductor
 nintendo        Nintendo
 nvidia  NVIDIA
 nxp     NXP Semiconductors
+picochip        Picochip Ltd
 powervr Imagination Technologies
 qcom    Qualcomm, Inc.
 ramtron Ramtron International
+realtek Realtek Semiconductor Corp.
 samsung Samsung Semiconductor
 sbs     Smart Battery System
 schindler       Schindler