scsi: dtc: remove from tree

The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

2 files changed, 0 insertions, 46 deletions

diff --git a/Documentation/scsi/dtc3x80.txt b/Documentation/scsi/dtc3x80.txt
deleted file mode 100644
index 1d7af9f9a8ed..000000000000
--- a/Documentation/scsi/dtc3x80.txt
+++ /dev/null
@@ -1,43 +0,0 @@
-README file for the Linux DTC3180/3280 scsi driver.
-by Ray Van Tassle (rayvt@comm.mot.com)  March 1996
-Based on the generic & core NCR5380 code by Drew Eckhard
-
-SCSI device driver for the DTC 3180/3280.
-Data Technology Corp---a division of Qume.
-
-The 3280 has a standard floppy interface.
-
-The 3180 does not.  Otherwise, they are identical.
-
-The DTC3x80 does not support DMA but it does have Pseudo-DMA which is
-supported by the driver.
-
-Its DTC406 scsi chip is supposedly compatible with the NCR 53C400.
-It is memory mapped, uses an IRQ, but no dma or io-port.  There is
-internal DMA, between SCSI bus and an on-chip 128-byte buffer.  Double
-buffering is done automagically by the chip.  Data is transferred
-between the on-chip buffer and CPU/RAM via memory moves.
-
-The driver detects the possible memory addresses (jumper selectable):
-        CC00, DC00, C800, and D800
-The possible IRQ's (jumper selectable) are:
-        IRQ 10, 11, 12, 15
-Parity is supported by the chip, but not by this driver.
-Information can be obtained from /proc/scsi/dtc3c80/N.
-
-Note on interrupts:
-
-The documentation says that it can be set to interrupt whenever the
-on-chip buffer needs CPU attention.  I couldn't get this to work.  So
-the driver polls for data-ready in the pseudo-DMA transfer routine.
-The interrupt support routines in the NCR3280.c core modules handle
-scsi disconnect/reconnect, and this (mostly) works.  However.....  I
-have tested it with 4 totally different hard drives (both SCSI-1 and
-SCSI-2), and one CDROM drive.  Interrupts works great for all but one
-specific hard drive.  For this one, the driver will eventually hang in
-the transfer state.  I have tested with: "dd bs=4k count=2k
-of=/dev/null if=/dev/sdb".  It reads ok for a while, then hangs.
-After beating my head against this for a couple of weeks, getting
-nowhere, I give up.  So.....This driver does NOT use interrupts, even
-if you have the card jumpered to an IRQ.  Probably nobody will ever
-care.
diff --git a/Documentation/scsi/scsi-parameters.txt b/Documentation/scsi/scsi-parameters.txt
index 00a03c0cd8c2..8e66dafa41e1 100644
--- a/Documentation/scsi/scsi-parameters.txt
+++ b/Documentation/scsi/scsi-parameters.txt
@@ -34,9 +34,6 @@ parameters may be changed at runtime by the command
                         See drivers/scsi/BusLogic.c, comment before function
                         BusLogic_ParseDriverOptions().
 
-        dtc3181e=       [HW,SCSI]
-                        See Documentation/scsi/g_NCR5380.txt.
-
         eata=           [HW,SCSI]
 
         fdomain=        [HW,SCSI]