litmus2008.git/arch/ppc/syslib/Makefile, branch master

[POWERPC] Pass the pci_controller into pci_exclude_device

2007-06-29T06:57:22+00:00

There are times that we need to know which controller we are on to decide
how to exclude devices properly.  We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.

Signed-off-by: Kumar Gala

[POWERPC] Stop using ppc_sys for Xilinx Virtex boards

2007-04-30T01:02:04+00:00

The arch/ppc/syslib/ppc_sys.c infrastructure does not work well for the
virtex ports.  Move the ml300 and ml403 board ports over to use the new
virtex_devices infrastructure.

Signed-off-by: Grant Likely 
Acked-by: Peter Korsgaard 
Signed-off-by: Paul Mackerras

[POWERPC] ppc: Add support for AMCC Taishan 440GX eval board

2007-02-13T04:35:52+00:00

This patch adds support for the AMCC Taishan PPC440GX evaluation
board.

This is still an arch/ppc port. I'm aware that the move of
4xx to arch/powerpc is making good progress right now. So this
patch is mainly intended to make the Taishan support available
for the community right now.

Signed-off-by: Stefan Roese 
Signed-off-by: Paul Mackerras

[POWERPC] Remove the broken Gemini support

2007-01-24T10:13:58+00:00

Signed-off-by: Adrian Bunk 
Signed-off-by: Paul Mackerras

[POWERPC] back up old school ipic.[hc] to arch/ppc

2006-08-30T00:34:33+00:00

Keep from breaking 83xx arch/ppc build.  Back up old school arch/powerpc/sysdev/ipic.[hc] to arch/ppc/syslib.

Signed-off-by: Kim Phillips 
Signed-off-by: Paul Mackerras

[POWERPC] Copy i8259 code back to arch/ppc

2006-07-03T09:55:30+00:00

This copies the i8259 interrupt controller driver from arch/powerpc
to arch/ppc. It's currently shared by both architectures, but the upcoming
arch/powerpc interrupt changes will break the arch/ppc builds. The changes
are too important to just use #ifdef's in the driver.

Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Paul Mackerras

ppc: Remove CHRP, POWER3 and POWER4 support from arch/ppc

2006-03-27T23:22:10+00:00

32-bit CHRP machines are now supported only in arch/powerpc, as are
all 64-bit PowerPC processors.  This means that we don't use
Open Firmware on any platform in arch/ppc any more.

This makes PReP support a single-platform option like every other
platform support option in arch/ppc now, thus CONFIG_PPC_MULTIPLATFORM
is gone from arch/ppc.  CONFIG_PPC_PREP is the option that selects
PReP support and is generally what has replaced
CONFIG_PPC_MULTIPLATFORM within arch/ppc.

_machine is all but dead now, being #defined to 0.

Updated Makefiles, comments and Kconfig options generally to reflect
these changes.

Signed-off-by: Paul Mackerras

[PATCH] powerpc: Migrate ML300 reference design to the platform bus

2006-02-07T11:35:59+00:00

Signed-off-by: Grant C. Likely 
Signed-off-by: Paul Mackerras

[PATCH] powerpc: Make Virtex-II Pro support generic for all Virtex devices

2006-02-07T11:35:57+00:00

The PPC405 hard core is used in both the Virtex-II Pro and Virtex 4 FX
FPGAs.  This patch cleans up the Virtex naming convention to reflect more
than just the Virtex-II Pro.

Rename files virtex-ii_pro.[ch] to virtex.[ch]
Rename config value VIRTEX_II_PRO to XILINX_VIRTEX

Signed-off-by: Grant C. Likely 
Signed-off-by: Paul Mackerras

[PATCH] ppc: Remove powermac support from ARCH=ppc

2006-01-15T06:30:44+00:00

This makes it possible to build kernels for PReP and/or CHRP
with ARCH=ppc by removing the (non-building) powermac support.
It's now also possible to select PReP and CHRP independently.
Powermac users should now build with ARCH=powerpc instead of
ARCH=ppc.  (This does mean that it is no longer possible to
build a 32-bit kernel for a G5.)

Signed-off-by: Paul Mackerras