1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
|
#
# USB device configuration
#
menuconfig USB_SUPPORT
bool "USB support"
depends on HAS_IOMEM
default y
---help---
This option adds core support for Universal Serial Bus (USB).
You will also need drivers from the following menu to make use of it.
if USB_SUPPORT
# Host-side USB depends on having a host controller
# NOTE: dummy_hcd is always an option, but it's ignored here ...
# NOTE: SL-811 option should be board-specific ...
config USB_ARCH_HAS_HCD
boolean
default y if USB_ARCH_HAS_OHCI
default y if USB_ARCH_HAS_EHCI
default y if PCMCIA && !M32R # sl811_cs
default y if ARM # SL-811
default PCI
# many non-PCI SOC chips embed OHCI
config USB_ARCH_HAS_OHCI
boolean
# ARM:
default y if SA1111
default y if ARCH_OMAP
default y if ARCH_LH7A404
default y if ARCH_S3C2410
default y if PXA27x
default y if ARCH_EP93XX
default y if ARCH_AT91
default y if ARCH_PNX4008
# PPC:
default y if STB03xxx
default y if PPC_MPC52xx
# MIPS:
default y if SOC_AU1X00
# more:
default PCI
# some non-PCI hcds implement EHCI
config USB_ARCH_HAS_EHCI
boolean
default y if PPC_83xx
default y if SOC_AU1200
default PCI
# ARM SA1111 chips have a non-PCI based "OHCI-compatible" USB host interface.
config USB
tristate "Support for Host-side USB"
depends on USB_ARCH_HAS_HCD
---help---
Universal Serial Bus (USB) is a specification for a serial bus
subsystem which offers higher speeds and more features than the
traditional PC serial port. The bus supplies power to peripherals
and allows for hot swapping. Up to 127 USB peripherals can be
connected to a single USB host in a tree structure.
The USB host is the root of the tree, the peripherals are the
leaves and the inner nodes are special USB devices called hubs.
Most PCs now have USB host ports, used to connect peripherals
such as scanners, keyboards, mice, modems, cameras, disks,
flash memory, network links, and printers to the PC.
Say Y here if your computer has a host-side USB port and you want
to use USB devices. You then need to say Y to at least one of the
Host Controller Driver (HCD) options below. Choose a USB 1.1
controller, such as "UHCI HCD support" or "OHCI HCD support",
and "EHCI HCD (USB 2.0) support" except for older systems that
do not have USB 2.0 support. It doesn't normally hurt to select
them all if you are not certain.
If your system has a device-side USB port, used in the peripheral
side of the USB protocol, see the "USB Gadget" framework instead.
After choosing your HCD, then select drivers for the USB peripherals
you'll be using. You may want to check out the information provided
in <file:Documentation/usb/> and especially the links given in
<file:Documentation/usb/usb-help.txt>.
To compile this driver as a module, choose M here: the
module will be called usbcore.
source "drivers/usb/core/Kconfig"
source "drivers/usb/host/Kconfig"
source "drivers/usb/class/Kconfig"
source "drivers/usb/storage/Kconfig"
source "drivers/usb/image/Kconfig"
source "drivers/usb/mon/Kconfig"
comment "USB port drivers"
depends on USB
config USB_USS720
tristate "USS720 parport driver"
depends on USB && PARPORT
select PARPORT_NOT_PC
---help---
This driver is for USB parallel port adapters that use the Lucent
Technologies USS-720 chip. These cables are plugged into your USB
port and provide USB compatibility to peripherals designed with
parallel port interfaces.
The chip has two modes: automatic mode and manual mode. In automatic
mode, it looks to the computer like a standard USB printer. Only
printers may be connected to the USS-720 in this mode. The generic
USB printer driver ("USB Printer support", above) may be used in
that mode, and you can say N here if you want to use the chip only
in this mode.
Manual mode is not limited to printers, any parallel port
device should work. This driver utilizes manual mode.
Note however that some operations are three orders of magnitude
slower than on a PCI/ISA Parallel Port, so timing critical
applications might not work.
Say Y here if you own an USS-720 USB->Parport cable and intend to
connect anything other than a printer to it.
To compile this driver as a module, choose M here: the
module will be called uss720.
source "drivers/usb/serial/Kconfig"
source "drivers/usb/misc/Kconfig"
source "drivers/usb/atm/Kconfig"
source "drivers/usb/gadget/Kconfig"
endif # USB_SUPPORT
|
