1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
|
/* Board-specific reboot/shutdown routines
*
* Copyright (c) 2009 Philippe Vachon <philippe@cowpig.ca>
*
* Copyright (C) 2009 Lemote Inc.
* Author: Wu Zhangjin, wuzhangjin@gmail.com
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/io.h>
#include <linux/delay.h>
#include <linux/types.h>
#include <asm/bootinfo.h>
#include <loongson.h>
#include <cs5536/cs5536.h>
#include "ec_kb3310b.h"
static void reset_cpu(void)
{
/*
* reset cpu to full speed, this is needed when enabling cpu frequency
* scalling
*/
LOONGSON_CHIPCFG0 |= 0x7;
}
/* reset support for fuloong2f */
static void fl2f_reboot(void)
{
reset_cpu();
/* send a reset signal to south bridge.
*
* NOTE: if enable "Power Management" in kernel, rtl8169 will not reset
* normally with this reset operation and it will not work in PMON, but
* you can type halt command and then reboot, seems the hardware reset
* logic not work normally.
*/
{
u32 hi, lo;
_rdmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), &hi, &lo);
lo |= 0x00000001;
_wrmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), hi, lo);
}
}
static void fl2f_shutdown(void)
{
u32 hi, lo, val;
int gpio_base;
/* get gpio base */
_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &lo);
gpio_base = lo & 0xff00;
/* make cs5536 gpio13 output enable */
val = inl(gpio_base + GPIOL_OUT_EN);
val &= ~(1 << (16 + 13));
val |= (1 << 13);
outl(val, gpio_base + GPIOL_OUT_EN);
mmiowb();
/* make cs5536 gpio13 output low level voltage. */
val = inl(gpio_base + GPIOL_OUT_VAL) & ~(1 << (13));
val |= (1 << (16 + 13));
outl(val, gpio_base + GPIOL_OUT_VAL);
mmiowb();
}
/* reset support for yeeloong2f and mengloong2f notebook */
void ml2f_reboot(void)
{
reset_cpu();
/* sending an reset signal to EC(embedded controller) */
ec_write(REG_RESET, BIT_RESET_ON);
}
#define yl2f89_reboot ml2f_reboot
/* menglong(7inches) laptop has different shutdown logic from 8.9inches */
#define EC_SHUTDOWN_IO_PORT_HIGH 0xff2d
#define EC_SHUTDOWN_IO_PORT_LOW 0xff2e
#define EC_SHUTDOWN_IO_PORT_DATA 0xff2f
#define REG_SHUTDOWN_HIGH 0xFC
#define REG_SHUTDOWN_LOW 0x29
#define BIT_SHUTDOWN_ON (1 << 1)
static void ml2f_shutdown(void)
{
u8 val;
u64 i;
outb(REG_SHUTDOWN_HIGH, EC_SHUTDOWN_IO_PORT_HIGH);
outb(REG_SHUTDOWN_LOW, EC_SHUTDOWN_IO_PORT_LOW);
mmiowb();
val = inb(EC_SHUTDOWN_IO_PORT_DATA);
outb(val & (~BIT_SHUTDOWN_ON), EC_SHUTDOWN_IO_PORT_DATA);
mmiowb();
/* need enough wait here... how many microseconds needs? */
for (i = 0; i < 0x10000; i++)
delay();
outb(val | BIT_SHUTDOWN_ON, EC_SHUTDOWN_IO_PORT_DATA);
mmiowb();
}
static void yl2f89_shutdown(void)
{
/* cpu-gpio0 output low */
LOONGSON_GPIODATA &= ~0x00000001;
/* cpu-gpio0 as output */
LOONGSON_GPIOIE &= ~0x00000001;
}
void mach_prepare_reboot(void)
{
switch (mips_machtype) {
case MACH_LEMOTE_FL2F:
case MACH_LEMOTE_NAS:
case MACH_LEMOTE_LL2F:
fl2f_reboot();
break;
case MACH_LEMOTE_ML2F7:
ml2f_reboot();
break;
case MACH_LEMOTE_YL2F89:
yl2f89_reboot();
break;
default:
break;
}
}
void mach_prepare_shutdown(void)
{
switch (mips_machtype) {
case MACH_LEMOTE_FL2F:
case MACH_LEMOTE_NAS:
case MACH_LEMOTE_LL2F:
fl2f_shutdown();
break;
case MACH_LEMOTE_ML2F7:
ml2f_shutdown();
break;
case MACH_LEMOTE_YL2F89:
yl2f89_shutdown();
break;
default:
break;
}
}
|
