/****************************************************************************** * * This file is provided under a dual BSD/GPLv2 license. When using or * redistributing this file, you may do so under either license. * * GPL LICENSE SUMMARY * * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of version 2 of the GNU General Public License as * published by the Free Software Foundation. * * This program is distributed in the hope that it will be useful, but * WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU * General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, * USA * * The full GNU General Public License is included in this distribution * in the file called LICENSE.GPL. * * Contact Information: * Intel Linux Wireless * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 * * BSD LICENSE * * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * * Neither the name Intel Corporation nor the names of its * contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * *****************************************************************************/ #ifndef __il_fh_h__ #define __il_fh_h__ /****************************/ /* Flow Handler Definitions */ /****************************/ /** * This I/O area is directly read/writable by driver (e.g. Linux uses writel()) * Addresses are offsets from device's PCI hardware base address. */ #define FH_MEM_LOWER_BOUND (0x1000) #define FH_MEM_UPPER_BOUND (0x2000) /** * Keep-Warm (KW) buffer base address. * * Driver must allocate a 4KByte buffer that is used by 4965 for keeping the * host DRAM powered on (via dummy accesses to DRAM) to maintain low-latency * DRAM access when 4965 is Txing or Rxing. The dummy accesses prevent host * from going into a power-savings mode that would cause higher DRAM latency, * and possible data over/under-runs, before all Tx/Rx is complete. * * Driver loads FH_KW_MEM_ADDR_REG with the physical address (bits 35:4) * of the buffer, which must be 4K aligned. Once this is set up, the 4965 * automatically invokes keep-warm accesses when normal accesses might not * be sufficient to maintain fast DRAM response. * * Bit fields: * 31-0: Keep-warm buffer physical base address [35:4], must be 4K aligned */ #define FH_KW_MEM_ADDR_REG (FH_MEM_LOWER_BOUND + 0x97C) /** * TFD Circular Buffers Base (CBBC) addresses * * 4965 has 16 base pointer registers, one for each of 16 host-DRAM-resident * circular buffers (CBs/queues) containing Transmit Frame Descriptors (TFDs) * (see struct il_tfd_frame). These 16 pointer registers are offset by 0x04 * bytes from one another. Each TFD circular buffer in DRAM must be 256-byte * aligned (address bits 0-7 must be 0). * * Bit fields in each pointer register: * 27-0: TFD CB physical base address [35:8], must be 256-byte aligned */ #define FH_MEM_CBBC_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0x9D0) #define FH_MEM_CBBC_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xA10) /* Find TFD CB base pointer for given queue (range 0-15). */ #define FH_MEM_CBBC_QUEUE(x) (FH_MEM_CBBC_LOWER_BOUND + (x) * 0x4) /** * Rx SRAM Control and Status Registers (RSCSR) * * These registers provide handshake between driver and 4965 for the Rx queue * (this queue handles *all* command responses, notifications, Rx data, etc. * sent from 4965 uCode to host driver). Unlike Tx, there is only one Rx * queue, and only one Rx DMA/FIFO channel. Also unlike Tx, which can * concatenate up to 20 DRAM buffers to form a Tx frame, each Receive Buffer * Descriptor (RBD) points to only one Rx Buffer (RB); there is a 1:1 * mapping between RBDs and RBs. * * Driver must allocate host DRAM memory for the following, and set the * physical address of each into 4965 registers: * * 1) Receive Buffer Descriptor (RBD) circular buffer (CB), typically with 256 * entries (although any power of 2, up to 4096, is selectable by driver). * Each entry (1 dword) points to a receive buffer (RB) of consistent size * (typically 4K, although 8K or 16K are also selectable by driver). * Driver sets up RB size and number of RBDs in the CB via Rx config * register FH_MEM_RCSR_CHNL0_CONFIG_REG. * * Bit fields within one RBD: * 27-0: Receive Buffer physical address bits [35:8], 256-byte aligned * * Driver sets physical address [35:8] of base of RBD circular buffer * into FH_RSCSR_CHNL0_RBDCB_BASE_REG [27:0]. * * 2) Rx status buffer, 8 bytes, in which 4965 indicates which Rx Buffers * (RBs) have been filled, via a "write pointer", actually the idx of * the RB's corresponding RBD within the circular buffer. Driver sets * physical address [35:4] into FH_RSCSR_CHNL0_STTS_WPTR_REG [31:0]. * * Bit fields in lower dword of Rx status buffer (upper dword not used * by driver; see struct il4965_shared, val0): * 31-12: Not used by driver * 11- 0: Index of last filled Rx buffer descriptor * (4965 writes, driver reads this value) * * As the driver prepares Receive Buffers (RBs) for 4965 to fill, driver must * enter pointers to these RBs into contiguous RBD circular buffer entries, * and update the 4965's "write" idx register, * FH_RSCSR_CHNL0_RBDCB_WPTR_REG. * * This "write" idx corresponds to the *next* RBD that the driver will make * available, i.e. one RBD past the tail of the ready-to-fill RBDs within * the circular buffer. This value should initially be 0 (before preparing any * RBs), should be 8 after preparing the first 8 RBs (for example), and must * wrap back to 0 at the end of the circular buffer (but don't wrap before * "read" idx has advanced past 1! See below). * NOTE: 4965 EXPECTS THE WRITE IDX TO BE INCREMENTED IN MULTIPLES OF 8. * * As the 4965 fills RBs (referenced from contiguous RBDs within the circular * buffer), it updates the Rx status buffer in host DRAM, 2) described above, * to tell the driver the idx of the latest filled RBD. The driver must * read this "read" idx from DRAM after receiving an Rx interrupt from 4965. * * The driver must also internally keep track of a third idx, which is the * next RBD to process. When receiving an Rx interrupt, driver should process * all filled but unprocessed RBs up to, but not including, the RB * corresponding to the "read" idx. For example, if "read" idx becomes "1", * driver may process the RB pointed to by RBD 0. Depending on volume of * traffic, there may be many RBs to process. * * If read idx == write idx, 4965 thinks there is no room to put new data. * Due to this, the maximum number of filled RBs is 255, instead of 256. To * be safe, make sure that there is a gap of at least 2 RBDs between "write" * and "read" idxes; that is, make sure that there are no more than 254 * buffers waiting to be filled. */ #define FH_MEM_RSCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xBC0) #define FH_MEM_RSCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xC00) #define FH_MEM_RSCSR_CHNL0 (FH_MEM_RSCSR_LOWER_BOUND) /** * Physical base address of 8-byte Rx Status buffer. * Bit fields: * 31-0: Rx status buffer physical base address [35:4], must 16-byte aligned. */ #define FH_RSCSR_CHNL0_STTS_WPTR_REG (FH_MEM_RSCSR_CHNL0) /** * Physical base address of Rx Buffer Descriptor Circular Buffer. * Bit fields: * 27-0: RBD CD physical base address [35:8], must be 256-byte aligned. */ #define FH_RSCSR_CHNL0_RBDCB_BASE_REG (FH_MEM_RSCSR_CHNL0 + 0x004) /** * Rx write pointer (idx, really!). * Bit fields: * 11-0: Index of driver's most recent prepared-to-be-filled RBD, + 1. * NOTE: For 256-entry circular buffer, use only bits [7:0]. */ #define FH_RSCSR_CHNL0_RBDCB_WPTR_REG (FH_MEM_RSCSR_CHNL0 + 0x008) #define FH_RSCSR_CHNL0_WPTR (FH_RSCSR_CHNL0_RBDCB_WPTR_REG) /** * Rx Config/Status Registers (RCSR) * Rx Config Reg for channel 0 (only channel used) * * Driver must initialize FH_MEM_RCSR_CHNL0_CONFIG_REG as follows for * normal operation (see bit fields). * * Clearing FH_MEM_RCSR_CHNL0_CONFIG_REG to 0 turns off Rx DMA. * Driver should poll FH_MEM_RSSR_RX_STATUS_REG for * FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (bit 24) before continuing. * * Bit fields: * 31-30: Rx DMA channel enable: '00' off/pause, '01' pause at end of frame, * '10' operate normally * 29-24: reserved * 23-20: # RBDs in circular buffer = 2^value; use "8" for 256 RBDs (normal), * min "5" for 32 RBDs, max "12" for 4096 RBDs. * 19-18: reserved * 17-16: size of each receive buffer; '00' 4K (normal), '01' 8K, * '10' 12K, '11' 16K. * 15-14: reserved * 13-12: IRQ destination; '00' none, '01' host driver (normal operation) * 11- 4: timeout for closing Rx buffer and interrupting host (units 32 usec) * typical value 0x10 (about 1/2 msec) * 3- 0: reserved */ #define FH_MEM_RCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC00) #define FH_MEM_RCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xCC0) #define FH_MEM_RCSR_CHNL0 (FH_MEM_RCSR_LOWER_BOUND) #define FH_MEM_RCSR_CHNL0_CONFIG_REG (FH_MEM_RCSR_CHNL0) #define FH_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MSK (0x00000FF0) /* bits 4-11 */ #define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MSK (0x00001000) /* bits 12 */ #define FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MSK (0x00008000) /* bit 15 */ #define FH_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MSK (0x00030000) /* bits 16-17 */ #define FH_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MSK (0x00F00000) /* bits 20-23 */ #define FH_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MSK (0xC0000000) /* bits 30-31*/ #define FH_RCSR_RX_CONFIG_RBDCB_SIZE_POS (20) #define FH_RCSR_RX_CONFIG_REG_IRQ_RBTH_POS (4) #define RX_RB_TIMEOUT (0x10) #define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000) #define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000) #define FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000) #define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000) #define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_8K (0x00010000) #define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_12K (0x00020000) #define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_16K (0x00030000) #define FH_RCSR_CHNL0_RX_IGNORE_RXF_EMPTY (0x00000004) #define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000) #define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000) /** * Rx Shared Status Registers (RSSR) * * After stopping Rx DMA channel (writing 0 to * FH_MEM_RCSR_CHNL0_CONFIG_REG), driver must poll * FH_MEM_RSSR_RX_STATUS_REG until Rx channel is idle. * * Bit fields: * 24: 1 = Channel 0 is idle * * FH_MEM_RSSR_SHARED_CTRL_REG and FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV * contain default values that should not be altered by the driver. */ #define FH_MEM_RSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC40) #define FH_MEM_RSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xD00) #define FH_MEM_RSSR_SHARED_CTRL_REG (FH_MEM_RSSR_LOWER_BOUND) #define FH_MEM_RSSR_RX_STATUS_REG (FH_MEM_RSSR_LOWER_BOUND + 0x004) #define FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV\ (FH_MEM_RSSR_LOWER_BOUND + 0x008) #define FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (0x01000000) #define FH_MEM_TFDIB_REG1_ADDR_BITSHIFT 28 /* TFDB Area - TFDs buffer table */ #define FH_MEM_TFDIB_DRAM_ADDR_LSB_MSK (0xFFFFFFFF) #define FH_TFDIB_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0x900) #define FH_TFDIB_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0x958) #define FH_TFDIB_CTRL0_REG(_chnl) (FH_TFDIB_LOWER_BOUND + 0x8 * (_chnl)) #define FH_TFDIB_CTRL1_REG(_chnl) (FH_TFDIB_LOWER_BOUND + 0x8 * (_chnl) + 0x4) /** * Transmit DMA Channel Control/Status Registers (TCSR) * * 4965 has one configuration register for each of 8 Tx DMA/FIFO channels * supported in hardware (don't confuse these with the 16 Tx queues in DRAM, * which feed the DMA/FIFO channels); config regs are separated by 0x20 bytes. * * To use a Tx DMA channel, driver must initialize its * FH_TCSR_CHNL_TX_CONFIG_REG(chnl) with: * * FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE | * FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL * * All other bits should be 0. * * Bit fields: * 31-30: Tx DMA channel enable: '00' off/pause, '01' pause at end of frame, * '10' operate normally * 29- 4: Reserved, set to "0" * 3: Enable internal DMA requests (1, normal operation), disable (0) * 2- 0: Reserved, set to "0" */ #define FH_TCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xD00) #define FH_TCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xE60) /* Find Control/Status reg for given Tx DMA/FIFO channel */ #define FH49_TCSR_CHNL_NUM (7) #define FH50_TCSR_CHNL_NUM (8) /* TCSR: tx_config register values */ #define FH_TCSR_CHNL_TX_CONFIG_REG(_chnl) \ (FH_TCSR_LOWER_BOUND + 0x20 * (_chnl)) #define FH_TCSR_CHNL_TX_CREDIT_REG(_chnl) \ (FH_TCSR_LOWER_BOUND + 0x20 * (_chnl) + 0x4) #define FH_TCSR_CHNL_TX_BUF_STS_REG(_chnl) \ (FH_TCSR_LOWER_BOUND + 0x20 * (_chnl) + 0x8) #define FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_TXF (0x00000000) #define FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_DRV (0x00000001) #define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE (0x00000000) #define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE (0x00000008) #define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_NOINT (0x00000000) #define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_ENDTFD (0x00100000) #define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_IFTFD (0x00200000) #define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_NOINT (0x00000000) #define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_ENDTFD (0x00400000) #define FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_IFTFD (0x00800000) #define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE (0x00000000) #define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE_EOF (0x40000000) #define FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000) #define FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_EMPTY (0x00000000) #define FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_WAIT (0x00002000) #define FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_VALID (0x00000003) #define FH_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_NUM (20) #define FH_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_IDX (12) /** * Tx Shared Status Registers (TSSR) * * After stopping Tx DMA channel (writing 0 to * FH_TCSR_CHNL_TX_CONFIG_REG(chnl)), driver must poll * FH_TSSR_TX_STATUS_REG until selected Tx channel is idle * (channel's buffers empty | no pending requests). * * Bit fields: * 31-24: 1 = Channel buffers empty (channel 7:0) * 23-16: 1 = No pending requests (channel 7:0) */ #define FH_TSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xEA0) #define FH_TSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xEC0) #define FH_TSSR_TX_STATUS_REG (FH_TSSR_LOWER_BOUND + 0x010) /** * Bit fields for TSSR(Tx Shared Status & Control) error status register: * 31: Indicates an address error when accessed to internal memory * uCode/driver must write "1" in order to clear this flag * 30: Indicates that Host did not send the expected number of dwords to FH * uCode/driver must write "1" in order to clear this flag * 16-9:Each status bit is for one channel. Indicates that an (Error) ActDMA * command was received from the scheduler while the TRB was already full * with previous command * uCode/driver must write "1" in order to clear this flag * 7-0: Each status bit indicates a channel's TxCredit error. When an error * bit is set, it indicates that the FH has received a full indication * from the RTC TxFIFO and the current value of the TxCredit counter was * not equal to zero. This mean that the credit mechanism was not * synchronized to the TxFIFO status * uCode/driver must write "1" in order to clear this flag */ #define FH_TSSR_TX_ERROR_REG (FH_TSSR_LOWER_BOUND + 0x018) #define FH_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(_chnl) ((1 << (_chnl)) << 16) /* Tx service channels */ #define FH_SRVC_CHNL (9) #define FH_SRVC_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0x9C8) #define FH_SRVC_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0x9D0) #define FH_SRVC_CHNL_SRAM_ADDR_REG(_chnl) \ (FH_SRVC_LOWER_BOUND + ((_chnl) - 9) * 0x4) #define FH_TX_CHICKEN_BITS_REG (FH_MEM_LOWER_BOUND + 0xE98) /* Instruct FH to increment the retry count of a packet when * it is brought from the memory to TX-FIFO */ #define FH_TX_CHICKEN_BITS_SCD_AUTO_RETRY_EN (0x00000002) /* Keep Warm Size */ #define IL_KW_SIZE 0x1000 /* 4k */ #endif /* !__il_fh_h__ */