/* * IDE ATAPI streaming tape driver. * * Copyright (C) 1995-1999 Gadi Oxman * Copyright (C) 2003-2005 Bartlomiej Zolnierkiewicz * * This driver was constructed as a student project in the software laboratory * of the faculty of electrical engineering in the Technion - Israel's * Institute Of Technology, with the guide of Avner Lottem and Dr. Ilana David. * * It is hereby placed under the terms of the GNU general public license. * (See linux/COPYING). * * For a historical changelog see * Documentation/ide/ChangeLog.ide-tape.1995-2002 */ #define DRV_NAME "ide-tape" #define IDETAPE_VERSION "1.20" #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include enum { /* output errors only */ DBG_ERR = (1 << 0), /* output all sense key/asc */ DBG_SENSE = (1 << 1), /* info regarding all chrdev-related procedures */ DBG_CHRDEV = (1 << 2), /* all remaining procedures */ DBG_PROCS = (1 << 3), }; /* define to see debug info */ #define IDETAPE_DEBUG_LOG 0 #if IDETAPE_DEBUG_LOG #define debug_log(lvl, fmt, args...) \ { \ if (tape->debug_mask & lvl) \ printk(KERN_INFO "ide-tape: " fmt, ## args); \ } #else #define debug_log(lvl, fmt, args...) do {} while (0) #endif /**************************** Tunable parameters *****************************/ /* * After each failed packet command we issue a request sense command and retry * the packet command IDETAPE_MAX_PC_RETRIES times. * * Setting IDETAPE_MAX_PC_RETRIES to 0 will disable retries. */ #define IDETAPE_MAX_PC_RETRIES 3 /* * Some drives (for example, Seagate STT3401A Travan) require a very long * timeout, because they don't return an interrupt or clear their busy bit * until after the command completes (even retension commands). */ #define IDETAPE_WAIT_CMD (900*HZ) /* * The following parameter is used to select the point in the internal tape fifo * in which we will start to refill the buffer. Decreasing the following * parameter will improve the system's latency and interactive response, while * using a high value might improve system throughput. */ #define IDETAPE_FIFO_THRESHOLD 2 /* * DSC polling parameters. * * Polling for DSC (a single bit in the status register) is a very important * function in ide-tape. There are two cases in which we poll for DSC: * * 1. Before a read/write packet command, to ensure that we can transfer data * from/to the tape's data buffers, without causing an actual media access. * In case the tape is not ready yet, we take out our request from the device * request queue, so that ide.c could service requests from the other device * on the same interface in the meantime. * * 2. After the successful initialization of a "media access packet command", * which is a command that can take a long time to complete (the interval can * range from several seconds to even an hour). Again, we postpone our request * in the middle to free the bus for the other device. The polling frequency * here should be lower than the read/write frequency since those media access * commands are slow. We start from a "fast" frequency - IDETAPE_DSC_MA_FAST * (1 second), and if we don't receive DSC after IDETAPE_DSC_MA_THRESHOLD * (5 min), we switch it to a lower frequency - IDETAPE_DSC_MA_SLOW (1 min). * * We also set a timeout for the timer, in case something goes wrong. The * timeout should be longer then the maximum execution time of a tape operation. */ /* DSC timings. */ #define IDETAPE_DSC_RW_MIN 5*HZ/100 /* 50 msec */ #define IDETAPE_DSC_RW_MAX 40*HZ/100 /* 400 msec */ #define IDETAPE_DSC_RW_TIMEOUT 2*60*HZ /* 2 minutes */ #define IDETAPE_DSC_MA_FAST 2*HZ /* 2 seconds */ #define IDETAPE_DSC_MA_THRESHOLD 5*60*HZ /* 5 minutes */ #define IDETAPE_DSC_MA_SLOW 30*HZ /* 30 seconds */ #define IDETAPE_DSC_MA_TIMEOUT 2*60*60*HZ /* 2 hours */ /*************************** End of tunable parameters ***********************/ /* tape directions */ enum { IDETAPE_DIR_NONE = (1 << 0), IDETAPE_DIR_READ = (1 << 1), IDETAPE_DIR_WRITE = (1 << 2), }; struct idetape_bh { u32 b_size; atomic_t b_count; struct idetape_bh *b_reqnext; char *b_data; }; /* Tape door status */ #define DOOR_UNLOCKED 0 #define DOOR_LOCKED 1 #define DOOR_EXPLICITLY_LOCKED 2 /* Some defines for the SPACE command */ #define IDETAPE_SPACE_OVER_FILEMARK 1 #define IDETAPE_SPACE_TO_EOD 3 /* Some defines for the LOAD UNLOAD command */ #define IDETAPE_LU_LOAD_MASK 1 #define IDETAPE_LU_RETENSION_MASK 2 #define IDETAPE_LU_EOT_MASK 4 /* Error codes returned in rq->errors to the higher part of the driver. */ #define IDETAPE_ERROR_GENERAL 101 #define IDETAPE_ERROR_FILEMARK 102 #define IDETAPE_ERROR_EOD 103 /* Structures related to the SELECT SENSE / MODE SENSE packet commands. */ #define IDETAPE_BLOCK_DESCRIPTOR 0 #define IDETAPE_CAPABILITIES_PAGE 0x2a /* * Most of our global data which we need to save even as we leave the driver due * to an interrupt or a timer event is stored in the struct defined below. */ typedef struct ide_tape_obj { ide_drive_t *drive; ide_driver_t *driver; struct gendisk *disk; struct kref kref; /* * pc points to the current processed packet command. * * failed_pc points to the last failed packet command, or contains * NULL if we do not need to retry any packet command. This is * required since an additional packet command is needed before the * retry, to get detailed information on what went wrong. */ /* Current packet command */ struct ide_atapi_pc *pc; /* Last failed packet command */ struct ide_atapi_pc *failed_pc; /* used by REQ_IDETAPE_{READ,WRITE} requests */ struct ide_atapi_pc queued_pc; struct ide_atapi_pc request_sense_pc; struct request request_sense_rq; /* * DSC polling variables. * * While polling for DSC we use postponed_rq to postpone the current * request so that ide.c will be able to service pending requests on the * other device. Note that at most we will have only one DSC (usually * data transfer) request in the device request queue. */ struct request *postponed_rq; /* The time in which we started polling for DSC */ unsigned long dsc_polling_start; /* Timer used to poll for dsc */ struct timer_list dsc_timer; /* Read/Write dsc polling frequency */ unsigned long best_dsc_rw_freq; unsigned long dsc_poll_freq; unsigned long dsc_timeout; /* Read position information */ u8 partition; /* Current block */ unsigned int first_frame; /* Last error information */ u8 sense_key, asc, ascq; /* Character device operation */ unsigned int minor; /* device name */ char name[4]; /* Current character device data transfer direction */ u8 chrdev_dir; /* tape block size, usually 512 or 1024 bytes */ unsigned short blk_size; int user_bs_factor; /* Copy of the tape's Capabilities and Mechanical Page */ u8 caps[20]; /* * Active data transfer request parameters. * * At most, there is only one ide-tape originated data transfer request * in the device request queue. This allows ide.c to easily service * requests from the other device when we postpone our active request. */ /* Data buffer size chosen based on the tape's recommendation */ int buffer_size; /* merge buffer */ struct idetape_bh *merge_bh; /* size of the merge buffer */ int merge_bh_size; /* pointer to current buffer head within the merge buffer */ struct idetape_bh *bh; char *b_data; int b_count; int pages_per_buffer; /* Wasted space in each stage */ int excess_bh_size; /* protects the ide-tape queue */ spinlock_t lock; /* Measures average tape speed */ unsigned long avg_time; int avg_size; int avg_speed; /* the door is currently locked */ int door_locked; /* the tape hardware is write protected */ char drv_write_prot; /* the tape is write protected (hardware or opened as read-only) */ char write_prot; u32 debug_mask; } idetape_tape_t; static DEFINE_MUTEX(idetape_ref_mutex); static struct class *idetape_sysfs_class; #define to_ide_tape(obj) container_of(obj, struct ide_tape_obj, kref) #define ide_tape_g(disk) \ container_of((disk)->private_data, struct ide_tape_obj, driver) static void ide_tape_release(struct kref *); static struct ide_tape_obj *ide_tape_get(struct gendisk *disk) { struct ide_tape_obj *tape = NULL; mutex_lock(&idetape_ref_mutex); tape = ide_tape_g(disk); if (tape) { if (ide_device_get(tape->drive)) tape = NULL; else kref_get(&tape->kref); } mutex_unlock(&idetape_ref_mutex); return tape; } static void ide_tape_put(struct ide_tape_obj *tape) { ide_drive_t *drive = tape->drive; mutex_lock(&idetape_ref_mutex); kref_put(&tape->kref, ide_tape_release); ide_device_put(drive); mutex_unlock(&idetape_ref_mutex); } /* * The variables below are used for the character device interface. Additional * state variables are defined in our ide_drive_t structure. */ static struct ide_tape_obj *idetape_devs[MAX_HWIFS * MAX_DRIVES]; #define ide_tape_f(file) ((file)->private_data) static struct ide_tape_obj *ide_tape_chrdev_get(unsigned int i) { struct ide_tape_obj *tape = NULL; mutex_lock(&idetape_ref_mutex); tape = idetape_devs[i]; if (tape) kref_get(&tape->kref); mutex_unlock(&idetape_ref_mutex); return tape; } static void idetape_input_buffers(ide_drive_t *drive, struct ide_atapi_pc *pc, unsigned int bcount) { struct idetape_bh *bh = pc->bh; int count; while (bcount) { if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in " "idetape_input_buffers\n"); ide_pad_transfer(drive, 0, bcount); return; } count = min( (unsigned int)(bh->b_size - atomic_read(&bh->b_count)), bcount); drive->hwif->tp_ops->input_data(drive, NULL, bh->b_data + atomic_read(&bh->b_count), count); bcount -= count; atomic_add(count, &bh->b_count); if (atomic_read(&bh->b_count) == bh->b_size) { bh = bh->b_reqnext; if (bh) atomic_set(&bh->b_count, 0); } } pc->bh = bh; } static void idetape_output_buffers(ide_drive_t *drive, struct ide_atapi_pc *pc, unsigned int bcount) { struct idetape_bh *bh = pc->bh; int count; while (bcount) { if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in %s\n", __func__); return; } count = min((unsigned int)pc->b_count, (unsigned int)bcount); drive->hwif->tp_ops->output_data(drive, NULL, pc->b_data, count); bcount -= count; pc->b_data += count; pc->b_count -= count; if (!pc->b_count) { bh = bh->b_reqnext; pc->bh = bh; if (bh) { pc->b_data = bh->b_data; pc->b_count = atomic_read(&bh->b_count); } } } } static void idetape_update_buffers(ide_drive_t *drive, struct ide_atapi_pc *pc) { struct idetape_bh *bh = pc->bh; int count; unsigned int bcount = pc->xferred; if (pc->flags & PC_FLAG_WRITING) return; while (bcount) { if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in %s\n", __func__); return; } count = min((unsigned int)bh->b_size, (unsigned int)bcount); atomic_set(&bh->b_count, count); if (atomic_read(&bh->b_count) == bh->b_size) bh = bh->b_reqnext; bcount -= count; } pc->bh = bh; } /* * called on each failed packet command retry to analyze the request sense. We * currently do not utilize this information. */ static void idetape_analyze_error(ide_drive_t *drive, u8 *sense) { idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc *pc = tape->failed_pc; tape->sense_key = sense[2] & 0xF; tape->asc = sense[12]; tape->ascq = sense[13]; debug_log(DBG_ERR, "pc = %x, sense key = %x, asc = %x, ascq = %x\n", pc->c[0], tape->sense_key, tape->asc, tape->ascq); /* Correct pc->xferred by asking the tape. */ if (pc->flags & PC_FLAG_DMA_ERROR) { pc->xferred = pc->req_xfer - tape->blk_size * get_unaligned_be32(&sense[3]); idetape_update_buffers(drive, pc); } /* * If error was the result of a zero-length read or write command, * with sense key=5, asc=0x22, ascq=0, let it slide. Some drives * (i.e. Seagate STT3401A Travan) don't support 0-length read/writes. */ if ((pc->c[0] == READ_6 || pc->c[0] == WRITE_6) /* length == 0 */ && pc->c[4] == 0 && pc->c[3] == 0 && pc->c[2] == 0) { if (tape->sense_key == 5) { /* don't report an error, everything's ok */ pc->error = 0; /* don't retry read/write */ pc->flags |= PC_FLAG_ABORT; } } if (pc->c[0] == READ_6 && (sense[2] & 0x80)) { pc->error = IDETAPE_ERROR_FILEMARK; pc->flags |= PC_FLAG_ABORT; } if (pc->c[0] == WRITE_6) { if ((sense[2] & 0x40) || (tape->sense_key == 0xd && tape->asc == 0x0 && tape->ascq == 0x2)) { pc->error = IDETAPE_ERROR_EOD; pc->flags |= PC_FLAG_ABORT; } } if (pc->c[0] == READ_6 || pc->c[0] == WRITE_6) { if (tape->sense_key == 8) { pc->error = IDETAPE_ERROR_EOD; pc->flags |= PC_FLAG_ABORT; } if (!(pc->flags & PC_FLAG_ABORT) && pc->xferred) pc->retries = IDETAPE_MAX_PC_RETRIES + 1; } } /* Free data buffers completely. */ static void ide_tape_kfree_buffer(idetape_tape_t *tape) { struct idetape_bh *prev_bh, *bh = tape->merge_bh; while (bh) { u32 size = bh->b_size; while (size) { unsigned int order = fls(size >> PAGE_SHIFT)-1; if (bh->b_data) free_pages((unsigned long)bh->b_data, order); size &= (order-1); bh->b_data += (1 << order) * PAGE_SIZE; } prev_bh = bh; bh = bh->b_reqnext; kfree(prev_bh); } } static int idetape_end_request(ide_drive_t *drive, int uptodate, int nr_sects) { struct request *rq = HWGROUP(drive)->rq; idetape_tape_t *tape = drive->driver_data; unsigned long flags; int error; debug_log(DBG_PROCS, "Enter %s\n", __func__); switch (uptodate) { case 0: error = IDETAPE_ERROR_GENERAL; break; case 1: error = 0; break; default: error = uptodate; } rq->errors = error; if (error) tape->failed_pc = NULL; if (!blk_special_request(rq)) { ide_end_request(drive, uptodate, nr_sects); return 0; } spin_lock_irqsave(&tape->lock, flags); ide_end_drive_cmd(drive, 0, 0); spin_unlock_irqrestore(&tape->lock, flags); return 0; } static void ide_tape_callback(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc *pc = tape->pc; int uptodate = pc->error ? 0 : 1; debug_log(DBG_PROCS, "Enter %s\n", __func__); if (tape->failed_pc == pc) tape->failed_pc = NULL; if (pc->c[0] == REQUEST_SENSE) { if (uptodate) idetape_analyze_error(drive, pc->buf); else printk(KERN_ERR "ide-tape: Error in REQUEST SENSE " "itself - Aborting request!\n"); } else if (pc->c[0] == READ_6 || pc->c[0] == WRITE_6) { struct request *rq = drive->hwif->hwgroup->rq; int blocks = pc->xferred / tape->blk_size; tape->avg_size += blocks * tape->blk_size; if (time_after_eq(jiffies, tape->avg_time + HZ)) { tape->avg_speed = tape->avg_size * HZ / (jiffies - tape->avg_time) / 1024; tape->avg_size = 0; tape->avg_time = jiffies; } tape->first_frame += blocks; rq->current_nr_sectors -= blocks; if (pc->error) uptodate = pc->error; } else if (pc->c[0] == READ_POSITION && uptodate) { u8 *readpos = tape->pc->buf; debug_log(DBG_SENSE, "BOP - %s\n", (readpos[0] & 0x80) ? "Yes" : "No"); debug_log(DBG_SENSE, "EOP - %s\n", (readpos[0] & 0x40) ? "Yes" : "No"); if (readpos[0] & 0x4) { printk(KERN_INFO "ide-tape: Block location is unknown" "to the tape\n"); clear_bit(IDE_AFLAG_ADDRESS_VALID, &drive->atapi_flags); uptodate = 0; } else { debug_log(DBG_SENSE, "Block Location - %u\n", be32_to_cpup((__be32 *)&readpos[4])); tape->partition = readpos[1]; tape->first_frame = be32_to_cpup((__be32 *)&readpos[4]); set_bit(IDE_AFLAG_ADDRESS_VALID, &drive->atapi_flags); } } idetape_end_request(drive, uptodate, 0); } static void idetape_create_request_sense_cmd(struct ide_atapi_pc *pc) { ide_init_pc(pc); pc->c[0] = REQUEST_SENSE; pc->c[4] = 20; pc->req_xfer = 20; } /* * idetape_retry_pc is called when an error was detected during the * last packet command. We queue a request sense packet command in * the head of the request list. */ static void idetape_retry_pc(ide_drive_t *drive) { struct ide_tape_obj *tape = drive->driver_data; struct request *rq = &tape->request_sense_rq; struct ide_atapi_pc *pc = &tape->request_sense_pc; (void)ide_read_error(drive); idetape_create_request_sense_cmd(pc); set_bit(IDE_AFLAG_IGNORE_DSC, &drive->atapi_flags); ide_queue_pc_head(drive, tape->disk, pc, rq); } /* * Postpone the current request so that ide.c will be able to service requests * from another device on the same hwgroup while we are polling for DSC. */ static void idetape_postpone_request(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; debug_log(DBG_PROCS, "Enter %s\n", __func__); tape->postponed_rq = HWGROUP(drive)->rq; ide_stall_queue(drive, tape->dsc_poll_freq); } static void ide_tape_handle_dsc(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; /* Media access command */ tape->dsc_polling_start = jiffies; tape->dsc_poll_freq = IDETAPE_DSC_MA_FAST; tape->dsc_timeout = jiffies + IDETAPE_DSC_MA_TIMEOUT; /* Allow ide.c to handle other requests */ idetape_postpone_request(drive); } static int ide_tape_io_buffers(ide_drive_t *drive, struct ide_atapi_pc *pc, unsigned int bcount, int write) { if (write) idetape_output_buffers(drive, pc, bcount); else idetape_input_buffers(drive, pc, bcount); return bcount; } /* * This is the usual interrupt handler which will be called during a packet * command. We will transfer some of the data (as requested by the drive) and * will re-point interrupt handler to us. When data transfer is finished, we * will act according to the algorithm described before * idetape_issue_pc. */ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; return ide_pc_intr(drive, tape->pc, idetape_pc_intr, IDETAPE_WAIT_CMD, NULL, idetape_update_buffers, idetape_retry_pc, ide_tape_handle_dsc, ide_tape_io_buffers); } /* * Packet Command Interface * * The current Packet Command is available in tape->pc, and will not change * until we finish handling it. Each packet command is associated with a * callback function that will be called when the command is finished. * * The handling will be done in three stages: * * 1. idetape_issue_pc will send the packet command to the drive, and will set * the interrupt handler to idetape_pc_intr. * * 2. On each interrupt, idetape_pc_intr will be called. This step will be * repeated until the device signals us that no more interrupts will be issued. * * 3. ATAPI Tape media access commands have immediate status with a delayed * process. In case of a successful initiation of a media access packet command, * the DSC bit will be set when the actual execution of the command is finished. * Since the tape drive will not issue an interrupt, we have to poll for this * event. In this case, we define the request as "low priority request" by * setting rq_status to IDETAPE_RQ_POSTPONED, set a timer to poll for DSC and * exit the driver. * * ide.c will then give higher priority to requests which originate from the * other device, until will change rq_status to RQ_ACTIVE. * * 4. When the packet command is finished, it will be checked for errors. * * 5. In case an error was found, we queue a request sense packet command in * front of the request queue and retry the operation up to * IDETAPE_MAX_PC_RETRIES times. * * 6. In case no error was found, or we decided to give up and not to retry * again, the callback function will be called and then we will handle the next * request. */ static ide_startstop_t idetape_transfer_pc(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; return ide_transfer_pc(drive, tape->pc, idetape_pc_intr, IDETAPE_WAIT_CMD, NULL); } static ide_startstop_t idetape_issue_pc(ide_drive_t *drive, struct ide_atapi_pc *pc) { idetape_tape_t *tape = drive->driver_data; if (tape->pc->c[0] == REQUEST_SENSE && pc->c[0] == REQUEST_SENSE) { printk(KERN_ERR "ide-tape: possible ide-tape.c bug - " "Two request sense in serial were issued\n"); } if (tape->failed_pc == NULL && pc->c[0] != REQUEST_SENSE) tape->failed_pc = pc; /* Set the current packet command */ tape->pc = pc; if (pc->retries > IDETAPE_MAX_PC_RETRIES || (pc->flags & PC_FLAG_ABORT)) { /* * We will "abort" retrying a packet command in case legitimate * error code was received (crossing a filemark, or end of the * media, for example). */ if (!(pc->flags & PC_FLAG_ABORT)) { if (!(pc->c[0] == TEST_UNIT_READY && tape->sense_key == 2 && tape->asc == 4 && (tape->ascq == 1 || tape->ascq == 8))) { printk(KERN_ERR "ide-tape: %s: I/O error, " "pc = %2x, key = %2x, " "asc = %2x, ascq = %2x\n", tape->name, pc->c[0], tape->sense_key, tape->asc, tape->ascq); } /* Giving up */ pc->error = IDETAPE_ERROR_GENERAL; } tape->failed_pc = NULL; drive->pc_callback(drive); return ide_stopped; } debug_log(DBG_SENSE, "Retry #%d, cmd = %02X\n", pc->retries, pc->c[0]); pc->retries++; return ide_issue_pc(drive, pc, idetape_transfer_pc, IDETAPE_WAIT_CMD, NULL); } /* A mode sense command is used to "sense" tape parameters. */ static void idetape_create_mode_sense_cmd(struct ide_atapi_pc *pc, u8 page_code) { ide_init_pc(pc); pc->c[0] = MODE_SENSE; if (page_code != IDETAPE_BLOCK_DESCRIPTOR) /* DBD = 1 - Don't return block descriptors */ pc->c[1] = 8; pc->c[2] = page_code; /* * Changed pc->c[3] to 0 (255 will at best return unused info). * * For SCSI this byte is defined as subpage instead of high byte * of length and some IDE drives seem to interpret it this way * and return an error when 255 is used. */ pc->c[3] = 0; /* We will just discard data in that case */ pc->c[4] = 255; if (page_code == IDETAPE_BLOCK_DESCRIPTOR) pc->req_xfer = 12; else if (page_code == IDETAPE_CAPABILITIES_PAGE) pc->req_xfer = 24; else pc->req_xfer = 50; } static ide_startstop_t idetape_media_access_finished(ide_drive_t *drive) { ide_hwif_t *hwif = drive->hwif; idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc *pc = tape->pc; u8 stat; stat = hwif->tp_ops->read_status(hwif); if (stat & ATA_DSC) { if (stat & ATA_ERR) { /* Error detected */ if (pc->c[0] != TEST_UNIT_READY) printk(KERN_ERR "ide-tape: %s: I/O error, ", tape->name); /* Retry operation */ idetape_retry_pc(drive); return ide_stopped; } pc->error = 0; } else { pc->error = IDETAPE_ERROR_GENERAL; tape->failed_pc = NULL; } drive->pc_callback(drive); return ide_stopped; } static void ide_tape_create_rw_cmd(idetape_tape_t *tape, struct ide_atapi_pc *pc, struct request *rq, u8 opcode) { struct idetape_bh *bh = (struct idetape_bh *)rq->special; unsigned int length = rq->current_nr_sectors; ide_init_pc(pc); put_unaligned(cpu_to_be32(length), (unsigned int *) &pc->c[1]); pc->c[1] = 1; pc->bh = bh; pc->buf = NULL; pc->buf_size = length * tape->blk_size; pc->req_xfer = pc->buf_size; if (pc->req_xfer == tape->buffer_size) pc->flags |= PC_FLAG_DMA_OK; if (opcode == READ_6) { pc->c[0] = READ_6; atomic_set(&bh->b_count, 0); } else if (opcode == WRITE_6) { pc->c[0] = WRITE_6; pc->flags |= PC_FLAG_WRITING; pc->b_data = bh->b_data; pc->b_count = atomic_read(&bh->b_count); } memcpy(rq->cmd, pc->c, 12); } static ide_startstop_t idetape_do_request(ide_drive_t *drive, struct request *rq, sector_t block) { ide_hwif_t *hwif = drive->hwif; idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc *pc = NULL; struct request *postponed_rq = tape->postponed_rq; u8 stat; debug_log(DBG_SENSE, "sector: %llu, nr_sectors: %lu," " current_nr_sectors: %u\n", (unsigned long long)rq->sector, rq->nr_sectors, rq->current_nr_sectors); if (!blk_special_request(rq)) { /* We do not support buffer cache originated requests. */ printk(KERN_NOTICE "ide-tape: %s: Unsupported request in " "request queue (%d)\n", drive->name, rq->cmd_type); ide_end_request(drive, 0, 0); return ide_stopped; } /* Retry a failed packet command */ if (tape->failed_pc && tape->pc->c[0] == REQUEST_SENSE) { pc = tape->failed_pc; goto out; } if (postponed_rq != NULL) if (rq != postponed_rq) { printk(KERN_ERR "ide-tape: ide-tape.c bug - " "Two DSC requests were queued\n"); idetape_end_request(drive, 0, 0); return ide_stopped; } tape->postponed_rq = NULL; /* * If the tape is still busy, postpone our request and service * the other device meanwhile. */ stat = hwif->tp_ops->read_status(hwif); if (!drive->dsc_overlap && !(rq->cmd[13] & REQ_IDETAPE_PC2)) set_bit(IDE_AFLAG_IGNORE_DSC, &drive->atapi_flags); if (drive->post_reset == 1) { set_bit(IDE_AFLAG_IGNORE_DSC, &drive->atapi_flags); drive->post_reset = 0; } if (!test_and_clear_bit(IDE_AFLAG_IGNORE_DSC, &drive->atapi_flags) && (stat & ATA_DSC) == 0) { if (postponed_rq == NULL) { tape->dsc_polling_start = jiffies; tape->dsc_poll_freq = tape->best_dsc_rw_freq; tape->dsc_timeout = jiffies + IDETAPE_DSC_RW_TIMEOUT; } else if (time_after(jiffies, tape->dsc_timeout)) { printk(KERN_ERR "ide-tape: %s: DSC timeout\n", tape->name); if (rq->cmd[13] & REQ_IDETAPE_PC2) { idetape_media_access_finished(drive); return ide_stopped; } else { return ide_do_reset(drive); } } else if (time_after(jiffies, tape->dsc_polling_start + IDETAPE_DSC_MA_THRESHOLD)) tape->dsc_poll_freq = IDETAPE_DSC_MA_SLOW; idetape_postpone_request(drive); return ide_stopped; } if (rq->cmd[13] & REQ_IDETAPE_READ) { pc = &tape->queued_pc; ide_tape_create_rw_cmd(tape, pc, rq, READ_6); goto out; } if (rq->cmd[13] & REQ_IDETAPE_WRITE) { pc = &tape->queued_pc; ide_tape_create_rw_cmd(tape, pc, rq, WRITE_6); goto out; } if (rq->cmd[13] & REQ_IDETAPE_PC1) { pc = (struct ide_atapi_pc *) rq->buffer; rq->cmd[13] &= ~(REQ_IDETAPE_PC1); rq->cmd[13] |= REQ_IDETAPE_PC2; goto out; } if (rq->cmd[13] & REQ_IDETAPE_PC2) { idetape_media_access_finished(drive); return ide_stopped; } BUG(); out: return idetape_issue_pc(drive, pc); } /* * The function below uses __get_free_pages to allocate a data buffer of size * tape->buffer_size (or a bit more). We attempt to combine sequential pages as * much as possible. * * It returns a pointer to the newly allocated buffer, or NULL in case of * failure. */ static struct idetape_bh *ide_tape_kmalloc_buffer(idetape_tape_t *tape, int full, int clear) { struct idetape_bh *prev_bh, *bh, *merge_bh; int pages = tape->pages_per_buffer; unsigned int order, b_allocd; char *b_data = NULL; merge_bh = kmalloc(sizeof(struct idetape_bh), GFP_KERNEL); bh = merge_bh; if (bh == NULL) goto abort; order = fls(pages) - 1; bh->b_data = (char *) __get_free_pages(GFP_KERNEL, order); if (!bh->b_data) goto abort; b_allocd = (1 << order) * PAGE_SIZE; pages &= (order-1); if (clear) memset(bh->b_data, 0, b_allocd); bh->b_reqnext = NULL; bh->b_size = b_allocd; atomic_set(&bh->b_count, full ? bh->b_size : 0); while (pages) { order = fls(pages) - 1; b_data = (char *) __get_free_pages(GFP_KERNEL, order); if (!b_data) goto abort; b_allocd = (1 << order) * PAGE_SIZE; if (clear) memset(b_data, 0, b_allocd); /* newly allocated page frames below buffer header or ...*/ if (bh->b_data == b_data + b_allocd) { bh->b_size += b_allocd; bh->b_data -= b_allocd; if (full) atomic_add(b_allocd, &bh->b_count); continue; } /* they are above the header */ if (b_data == bh->b_data + bh->b_size) { bh->b_size += b_allocd; if (full) atomic_add(b_allocd, &bh->b_count); continue; } prev_bh = bh; bh = kmalloc(sizeof(struct idetape_bh), GFP_KERNEL); if (!bh) { free_pages((unsigned long) b_data, order); goto abort; } bh->b_reqnext = NULL; bh->b_data = b_data; bh->b_size = b_allocd; atomic_set(&bh->b_count, full ? bh->b_size : 0); prev_bh->b_reqnext = bh; pages &= (order-1); } bh->b_size -= tape->excess_bh_size; if (full) atomic_sub(tape->excess_bh_size, &bh->b_count); return merge_bh; abort: ide_tape_kfree_buffer(tape); return NULL; } static int idetape_copy_stage_from_user(idetape_tape_t *tape, const char __user *buf, int n) { struct idetape_bh *bh = tape->bh; int count; int ret = 0; while (n) { if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in %s\n", __func__); return 1; } count = min((unsigned int) (bh->b_size - atomic_read(&bh->b_count)), (unsigned int)n); if (copy_from_user(bh->b_data + atomic_read(&bh->b_count), buf, count)) ret = 1; n -= count; atomic_add(count, &bh->b_count); buf += count; if (atomic_read(&bh->b_count) == bh->b_size) { bh = bh->b_reqnext; if (bh) atomic_set(&bh->b_count, 0); } } tape->bh = bh; return ret; } static int idetape_copy_stage_to_user(idetape_tape_t *tape, char __user *buf, int n) { struct idetape_bh *bh = tape->bh; int count; int ret = 0; while (n) { if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in %s\n", __func__); return 1; } count = min(tape->b_count, n); if (copy_to_user(buf, tape->b_data, count)) ret = 1; n -= count; tape->b_data += count; tape->b_count -= count; buf += count; if (!tape->b_count) { bh = bh->b_reqnext; tape->bh = bh; if (bh) { tape->b_data = bh->b_data; tape->b_count = atomic_read(&bh->b_count); } } } return ret; } static void idetape_init_merge_buffer(idetape_tape_t *tape) { struct idetape_bh *bh = tape->merge_bh; tape->bh = tape->merge_bh; if (tape->chrdev_dir == IDETAPE_DIR_WRITE) atomic_set(&bh->b_count, 0); else { tape->b_data = bh->b_data; tape->b_count = atomic_read(&bh->b_count); } } /* * Write a filemark if write_filemark=1. Flush the device buffers without * writing a filemark otherwise. */ static void idetape_create_write_filemark_cmd(ide_drive_t *drive, struct ide_atapi_pc *pc, int write_filemark) { ide_init_pc(pc); pc->c[0] = WRITE_FILEMARKS; pc->c[4] = write_filemark; pc->flags |= PC_FLAG_WAIT_FOR_DSC; } static void idetape_create_test_unit_ready_cmd(struct ide_atapi_pc *pc) { ide_init_pc(pc); pc->c[0] = TEST_UNIT_READY; } /* * We add a special packet command request to the tail of the request queue, and * wait for it to be serviced. */ static int idetape_queue_pc_tail(ide_drive_t *drive, struct ide_atapi_pc *pc) { struct ide_tape_obj *tape = drive->driver_data; struct request *rq; int error; rq = blk_get_request(drive->queue, READ, __GFP_WAIT); rq->cmd_type = REQ_TYPE_SPECIAL; rq->cmd[13] = REQ_IDETAPE_PC1; rq->buffer = (char *)pc; memcpy(rq->cmd, pc->c, 12); error = blk_execute_rq(drive->queue, tape->disk, rq, 0); blk_put_request(rq); return error; } static void idetape_create_load_unload_cmd(ide_drive_t *drive, struct ide_atapi_pc *pc, int cmd) { ide_init_pc(pc); pc->c[0] = START_STOP; pc->c[4] = cmd; pc->flags |= PC_FLAG_WAIT_FOR_DSC; } static int idetape_wait_ready(ide_drive_t *drive, unsigned long timeout) { idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc pc; int load_attempted = 0; /* Wait for the tape to become ready */ set_bit(IDE_AFLAG_MEDIUM_PRESENT, &drive->atapi_flags); timeout += jiffies; while (time_before(jiffies, timeout)) { idetape_create_test_unit_ready_cmd(&pc); if (!idetape_queue_pc_tail(drive, &pc)) return 0; if ((tape->sense_key == 2 && tape->asc == 4 && tape->ascq == 2) || (tape->asc == 0x3A)) { /* no media */ if (load_attempted) return -ENOMEDIUM; idetape_create_load_unload_cmd(drive, &pc, IDETAPE_LU_LOAD_MASK); idetape_queue_pc_tail(drive, &pc); load_attempted = 1; /* not about to be ready */ } else if (!(tape->sense_key == 2 && tape->asc == 4 && (tape->ascq == 1 || tape->ascq == 8))) return -EIO; msleep(100); } return -EIO; } static int idetape_flush_tape_buffers(ide_drive_t *drive) { struct ide_atapi_pc pc; int rc; idetape_create_write_filemark_cmd(drive, &pc, 0); rc = idetape_queue_pc_tail(drive, &pc); if (rc) return rc; idetape_wait_ready(drive, 60 * 5 * HZ); return 0; } static void idetape_create_read_position_cmd(struct ide_atapi_pc *pc) { ide_init_pc(pc); pc->c[0] = READ_POSITION; pc->req_xfer = 20; } static int idetape_read_position(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc pc; int position; debug_log(DBG_PROCS, "Enter %s\n", __func__); idetape_create_read_position_cmd(&pc); if (idetape_queue_pc_tail(drive, &pc)) return -1; position = tape->first_frame; return position; } static void idetape_create_locate_cmd(ide_drive_t *drive, struct ide_atapi_pc *pc, unsigned int block, u8 partition, int skip) { ide_init_pc(pc); pc->c[0] = POSITION_TO_ELEMENT; pc->c[1] = 2; put_unaligned(cpu_to_be32(block), (unsigned int *) &pc->c[3]); pc->c[8] = partition; pc->flags |= PC_FLAG_WAIT_FOR_DSC; } static int idetape_create_prevent_cmd(ide_drive_t *drive, struct ide_atapi_pc *pc, int prevent) { idetape_tape_t *tape = drive->driver_data; /* device supports locking according to capabilities page */ if (!(tape->caps[6] & 0x01)) return 0; ide_init_pc(pc); pc->c[0] = ALLOW_MEDIUM_REMOVAL; pc->c[4] = prevent; return 1; } static int ide_tape_set_media_lock(ide_drive_t *drive, int on) { struct ide_atapi_pc pc; if (!idetape_create_prevent_cmd(drive, &pc, on)) return 0; return idetape_queue_pc_tail(drive, &pc); } static void __ide_tape_discard_merge_buffer(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; if (tape->chrdev_dir != IDETAPE_DIR_READ) return; clear_bit(IDE_AFLAG_FILEMARK, &drive->atapi_flags); tape->merge_bh_size = 0; if (tape->merge_bh != NULL) { ide_tape_kfree_buffer(tape); tape->merge_bh = NULL; } tape->chrdev_dir = IDETAPE_DIR_NONE; } /* * Position the tape to the requested block using the LOCATE packet command. * A READ POSITION command is then issued to check where we are positioned. Like * all higher level operations, we queue the commands at the tail of the request * queue and wait for their completion. */ static int idetape_position_tape(ide_drive_t *drive, unsigned int block, u8 partition, int skip) { idetape_tape_t *tape = drive->driver_data; int retval; struct ide_atapi_pc pc; if (tape->chrdev_dir == IDETAPE_DIR_READ) __ide_tape_discard_merge_buffer(drive); idetape_wait_ready(drive, 60 * 5 * HZ); idetape_create_locate_cmd(drive, &pc, block, partition, skip); retval = idetape_queue_pc_tail(drive, &pc); if (retval) return (retval); idetape_create_read_position_cmd(&pc); return (idetape_queue_pc_tail(drive, &pc)); } static void ide_tape_discard_merge_buffer(ide_drive_t *drive, int restore_position) { idetape_tape_t *tape = drive->driver_data; int seek, position; __ide_tape_discard_merge_buffer(drive); if (restore_position) { position = idetape_read_position(drive); seek = position > 0 ? position : 0; if (idetape_position_tape(drive, seek, 0, 0)) { printk(KERN_INFO "ide-tape: %s: position_tape failed in" " %s\n", tape->name, __func__); return; } } } /* * Generate a read/write request for the block device interface and wait for it * to be serviced. */ static int idetape_queue_rw_tail(ide_drive_t *drive, int cmd, int blocks, struct idetape_bh *bh) { idetape_tape_t *tape = drive->driver_data; struct request *rq; int ret, errors; debug_log(DBG_SENSE, "%s: cmd=%d\n", __func__, cmd); rq = blk_get_request(drive->queue, READ, __GFP_WAIT); rq->cmd_type = REQ_TYPE_SPECIAL; rq->cmd[13] = cmd; rq->rq_disk = tape->disk; rq->special = (void *)bh; rq->sector = tape->first_frame; rq->nr_sectors = blocks; rq->current_nr_sectors = blocks; blk_execute_rq(drive->queue, tape->disk, rq, 0); errors = rq->errors; ret = tape->blk_size * (blocks - rq->current_nr_sectors); blk_put_request(rq); if ((cmd & (REQ_IDETAPE_READ | REQ_IDETAPE_WRITE)) == 0) return 0; if (tape->merge_bh) idetape_init_merge_buffer(tape); if (errors == IDETAPE_ERROR_GENERAL) return -EIO; return ret; } static void idetape_create_inquiry_cmd(struct ide_atapi_pc *pc) { ide_init_pc(pc); pc->c[0] = INQUIRY; pc->c[4] = 254; pc->req_xfer = 254; } static void idetape_create_rewind_cmd(ide_drive_t *drive, struct ide_atapi_pc *pc) { ide_init_pc(pc); pc->c[0] = REZERO_UNIT; pc->flags |= PC_FLAG_WAIT_FOR_DSC; } static void idetape_create_erase_cmd(struct ide_atapi_pc *pc) { ide_init_pc(pc); pc->c[0] = ERASE; pc->c[1] = 1; pc->flags |= PC_FLAG_WAIT_FOR_DSC; } static void idetape_create_space_cmd(struct ide_atapi_pc *pc, int count, u8 cmd) { ide_init_pc(pc); pc->c[0] = SPACE; put_unaligned(cpu_to_be32(count), (unsigned int *) &pc->c[1]); pc->c[1] = cmd; pc->flags |= PC_FLAG_WAIT_FOR_DSC; } /* Queue up a character device originated write request. */ static int idetape_add_chrdev_write_request(ide_drive_t *drive, int blocks) { idetape_tape_t *tape = drive->driver_data; debug_log(DBG_CHRDEV, "Enter %s\n", __func__); return idetape_queue_rw_tail(drive, REQ_IDETAPE_WRITE, blocks, tape->merge_bh); } static void ide_tape_flush_merge_buffer(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; int blocks, min; struct idetape_bh *bh; if (tape->chrdev_dir != IDETAPE_DIR_WRITE) { printk(KERN_ERR "ide-tape: bug: Trying to empty merge buffer" " but we are not writing.\n"); return; } if (tape->merge_bh_size > tape->buffer_size) { printk(KERN_ERR "ide-tape: bug: merge_buffer too big\n"); tape->merge_bh_size = tape->buffer_size; } if (tape->merge_bh_size) { blocks = tape->merge_bh_size / tape->blk_size; if (tape->merge_bh_size % tape->blk_size) { unsigned int i; blocks++; i = tape->blk_size - tape->merge_bh_size % tape->blk_size; bh = tape->bh->b_reqnext; while (bh) { atomic_set(&bh->b_count, 0); bh = bh->b_reqnext; } bh = tape->bh; while (i) { if (bh == NULL) { printk(KERN_INFO "ide-tape: bug," " bh NULL\n"); break; } min = min(i, (unsigned int)(bh->b_size - atomic_read(&bh->b_count))); memset(bh->b_data + atomic_read(&bh->b_count), 0, min); atomic_add(min, &bh->b_count); i -= min; bh = bh->b_reqnext; } } (void) idetape_add_chrdev_write_request(drive, blocks); tape->merge_bh_size = 0; } if (tape->merge_bh != NULL) { ide_tape_kfree_buffer(tape); tape->merge_bh = NULL; } tape->chrdev_dir = IDETAPE_DIR_NONE; } static int idetape_init_read(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; int bytes_read; /* Initialize read operation */ if (tape->chrdev_dir != IDETAPE_DIR_READ) { if (tape->chrdev_dir == IDETAPE_DIR_WRITE) { ide_tape_flush_merge_buffer(drive); idetape_flush_tape_buffers(drive); } if (tape->merge_bh || tape->merge_bh_size) { printk(KERN_ERR "ide-tape: merge_bh_size should be" " 0 now\n"); tape->merge_bh_size = 0; } tape->merge_bh = ide_tape_kmalloc_buffer(tape, 0, 0); if (!tape->merge_bh) return -ENOMEM; tape->chrdev_dir = IDETAPE_DIR_READ; /* * Issue a read 0 command to ensure that DSC handshake is * switched from completion mode to buffer available mode. * No point in issuing this if DSC overlap isn't supported, some * drives (Seagate STT3401A) will return an error. */ if (drive->dsc_overlap) { bytes_read = idetape_queue_rw_tail(drive, REQ_IDETAPE_READ, 0, tape->merge_bh); if (bytes_read < 0) { ide_tape_kfree_buffer(tape); tape->merge_bh = NULL; tape->chrdev_dir = IDETAPE_DIR_NONE; return bytes_read; } } } return 0; } /* called from idetape_chrdev_read() to service a chrdev read request. */ static int idetape_add_chrdev_read_request(ide_drive_t *drive, int blocks) { idetape_tape_t *tape = drive->driver_data; debug_log(DBG_PROCS, "Enter %s, %d blocks\n", __func__, blocks); /* If we are at a filemark, return a read length of 0 */ if (test_bit(IDE_AFLAG_FILEMARK, &drive->atapi_flags)) return 0; idetape_init_read(drive); return idetape_queue_rw_tail(drive, REQ_IDETAPE_READ, blocks, tape->merge_bh); } static void idetape_pad_zeros(ide_drive_t *drive, int bcount) { idetape_tape_t *tape = drive->driver_data; struct idetape_bh *bh; int blocks; while (bcount) { unsigned int count; bh = tape->merge_bh; count = min(tape->buffer_size, bcount); bcount -= count; blocks = count / tape->blk_size; while (count) { atomic_set(&bh->b_count, min(count, (unsigned int)bh->b_size)); memset(bh->b_data, 0, atomic_read(&bh->b_count)); count -= atomic_read(&bh->b_count); bh = bh->b_reqnext; } idetape_queue_rw_tail(drive, REQ_IDETAPE_WRITE, blocks, tape->merge_bh); } } /* * Rewinds the tape to the Beginning Of the current Partition (BOP). We * currently support only one partition. */ static int idetape_rewind_tape(ide_drive_t *drive) { int retval; struct ide_atapi_pc pc; idetape_tape_t *tape; tape = drive->driver_data; debug_log(DBG_SENSE, "Enter %s\n", __func__); idetape_create_rewind_cmd(drive, &pc); retval = idetape_queue_pc_tail(drive, &pc); if (retval) return retval; idetape_create_read_position_cmd(&pc); retval = idetape_queue_pc_tail(drive, &pc); if (retval) return retval; return 0; } /* mtio.h compatible commands should be issued to the chrdev interface. */ static int idetape_blkdev_ioctl(ide_drive_t *drive, unsigned int cmd, unsigned long arg) { idetape_tape_t *tape = drive->driver_data; void __user *argp = (void __user *)arg; struct idetape_config { int dsc_rw_frequency; int dsc_media_access_frequency; int nr_stages; } config; debug_log(DBG_PROCS, "Enter %s\n", __func__); switch (cmd) { case 0x0340: if (copy_from_user(&config, argp, sizeof(config))) return -EFAULT; tape->best_dsc_rw_freq = config.dsc_rw_frequency; break; case 0x0350: config.dsc_rw_frequency = (int) tape->best_dsc_rw_freq; config.nr_stages = 1; if (copy_to_user(argp, &config, sizeof(config))) return -EFAULT; break; default: return -EIO; } return 0; } static int idetape_space_over_filemarks(ide_drive_t *drive, short mt_op, int mt_count) { idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc pc; int retval, count = 0; int sprev = !!(tape->caps[4] & 0x20); if (mt_count == 0) return 0; if (MTBSF == mt_op || MTBSFM == mt_op) { if (!sprev) return -EIO; mt_count = -mt_count; } if (tape->chrdev_dir == IDETAPE_DIR_READ) { tape->merge_bh_size = 0; if (test_and_clear_bit(IDE_AFLAG_FILEMARK, &drive->atapi_flags)) ++count; ide_tape_discard_merge_buffer(drive, 0); } switch (mt_op) { case MTFSF: case MTBSF: idetape_create_space_cmd(&pc, mt_count - count, IDETAPE_SPACE_OVER_FILEMARK); return idetape_queue_pc_tail(drive, &pc); case MTFSFM: case MTBSFM: if (!sprev) return -EIO; retval = idetape_space_over_filemarks(drive, MTFSF, mt_count - count); if (retval) return retval; count = (MTBSFM == mt_op ? 1 : -1); return idetape_space_over_filemarks(drive, MTFSF, count); default: printk(KERN_ERR "ide-tape: MTIO operation %d not supported\n", mt_op); return -EIO; } } /* * Our character device read / write functions. * * The tape is optimized to maximize throughput when it is transferring an * integral number of the "continuous transfer limit", which is a parameter of * the specific tape (26kB on my particular tape, 32kB for Onstream). * * As of version 1.3 of the driver, the character device provides an abstract * continuous view of the media - any mix of block sizes (even 1 byte) on the * same backup/restore procedure is supported. The driver will internally * convert the requests to the recommended transfer unit, so that an unmatch * between the user's block size to the recommended size will only result in a * (slightly) increased driver overhead, but will no longer hit performance. * This is not applicable to Onstream. */ static ssize_t idetape_chrdev_read(struct file *file, char __user *buf, size_t count, loff_t *ppos) { struct ide_tape_obj *tape = ide_tape_f(file); ide_drive_t *drive = tape->drive; ssize_t bytes_read, temp, actually_read = 0, rc; ssize_t ret = 0; u16 ctl = *(u16 *)&tape->caps[12]; debug_log(DBG_CHRDEV, "Enter %s, count %Zd\n", __func__, count); if (tape->chrdev_dir != IDETAPE_DIR_READ) { if (test_bit(IDE_AFLAG_DETECT_BS, &drive->atapi_flags)) if (count > tape->blk_size && (count % tape->blk_size) == 0) tape->user_bs_factor = count / tape->blk_size; } rc = idetape_init_read(drive); if (rc < 0) return rc; if (count == 0) return (0); if (tape->merge_bh_size) { actually_read = min((unsigned int)(tape->merge_bh_size), (unsigned int)count); if (idetape_copy_stage_to_user(tape, buf, actually_read)) ret = -EFAULT; buf += actually_read; tape->merge_bh_size -= actually_read; count -= actually_read; } while (count >= tape->buffer_size) { bytes_read = idetape_add_chrdev_read_request(drive, ctl); if (bytes_read <= 0) goto finish; if (idetape_copy_stage_to_user(tape, buf, bytes_read)) ret = -EFAULT; buf += bytes_read; count -= bytes_read; actually_read += bytes_read; } if (count) { bytes_read = idetape_add_chrdev_read_request(drive, ctl); if (bytes_read <= 0) goto finish; temp = min((unsigned long)count, (unsigned long)bytes_read); if (idetape_copy_stage_to_user(tape, buf, temp)) ret = -EFAULT; actually_read += temp; tape->merge_bh_size = bytes_read-temp; } finish: if (!actually_read && test_bit(IDE_AFLAG_FILEMARK, &drive->atapi_flags)) { debug_log(DBG_SENSE, "%s: spacing over filemark\n", tape->name); idetape_space_over_filemarks(drive, MTFSF, 1); return 0; } return ret ? ret : actually_read; } static ssize_t idetape_chrdev_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos) { struct ide_tape_obj *tape = ide_tape_f(file); ide_drive_t *drive = tape->drive; ssize_t actually_written = 0; ssize_t ret = 0; u16 ctl = *(u16 *)&tape->caps[12]; /* The drive is write protected. */ if (tape->write_prot) return -EACCES; debug_log(DBG_CHRDEV, "Enter %s, count %Zd\n", __func__, count); /* Initialize write operation */ if (tape->chrdev_dir != IDETAPE_DIR_WRITE) { if (tape->chrdev_dir == IDETAPE_DIR_READ) ide_tape_discard_merge_buffer(drive, 1); if (tape->merge_bh || tape->merge_bh_size) { printk(KERN_ERR "ide-tape: merge_bh_size " "should be 0 now\n"); tape->merge_bh_size = 0; } tape->merge_bh = ide_tape_kmalloc_buffer(tape, 0, 0); if (!tape->merge_bh) return -ENOMEM; tape->chrdev_dir = IDETAPE_DIR_WRITE; idetape_init_merge_buffer(tape); /* * Issue a write 0 command to ensure that DSC handshake is * switched from completion mode to buffer available mode. No * point in issuing this if DSC overlap isn't supported, some * drives (Seagate STT3401A) will return an error. */ if (drive->dsc_overlap) { ssize_t retval = idetape_queue_rw_tail(drive, REQ_IDETAPE_WRITE, 0, tape->merge_bh); if (retval < 0) { ide_tape_kfree_buffer(tape); tape->merge_bh = NULL; tape->chrdev_dir = IDETAPE_DIR_NONE; return retval; } } } if (count == 0) return (0); if (tape->merge_bh_size) { if (tape->merge_bh_size >= tape->buffer_size) { printk(KERN_ERR "ide-tape: bug: merge buf too big\n"); tape->merge_bh_size = 0; } actually_written = min((unsigned int) (tape->buffer_size - tape->merge_bh_size), (unsigned int)count); if (idetape_copy_stage_from_user(tape, buf, actually_written)) ret = -EFAULT; buf += actually_written; tape->merge_bh_size += actually_written; count -= actually_written; if (tape->merge_bh_size == tape->buffer_size) { ssize_t retval; tape->merge_bh_size = 0; retval = idetape_add_chrdev_write_request(drive, ctl); if (retval <= 0) return (retval); } } while (count >= tape->buffer_size) { ssize_t retval; if (idetape_copy_stage_from_user(tape, buf, tape->buffer_size)) ret = -EFAULT; buf += tape->buffer_size; count -= tape->buffer_size; retval = idetape_add_chrdev_write_request(drive, ctl); actually_written += tape->buffer_size; if (retval <= 0) return (retval); } if (count) { actually_written += count; if (idetape_copy_stage_from_user(tape, buf, count)) ret = -EFAULT; tape->merge_bh_size += count; } return ret ? ret : actually_written; } static int idetape_write_filemark(ide_drive_t *drive) { struct ide_atapi_pc pc; /* Write a filemark */ idetape_create_write_filemark_cmd(drive, &pc, 1); if (idetape_queue_pc_tail(drive, &pc)) { printk(KERN_ERR "ide-tape: Couldn't write a filemark\n"); return -EIO; } return 0; } /* * Called from idetape_chrdev_ioctl when the general mtio MTIOCTOP ioctl is * requested. * * Note: MTBSF and MTBSFM are not supported when the tape doesn't support * spacing over filemarks in the reverse direction. In this case, MTFSFM is also * usually not supported. * * The following commands are currently not supported: * * MTFSS, MTBSS, MTWSM, MTSETDENSITY, MTSETDRVBUFFER, MT_ST_BOOLEANS, * MT_ST_WRITE_THRESHOLD. */ static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count) { idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc pc; int i, retval; debug_log(DBG_ERR, "Handling MTIOCTOP ioctl: mt_op=%d, mt_count=%d\n", mt_op, mt_count); switch (mt_op) { case MTFSF: case MTFSFM: case MTBSF: case MTBSFM: if (!mt_count) return 0; return idetape_space_over_filemarks(drive, mt_op, mt_count); default: break; } switch (mt_op) { case MTWEOF: if (tape->write_prot) return -EACCES; ide_tape_discard_merge_buffer(drive, 1); for (i = 0; i < mt_count; i++) { retval = idetape_write_filemark(drive); if (retval) return retval; } return 0; case MTREW: ide_tape_discard_merge_buffer(drive, 0); if (idetape_rewind_tape(drive)) return -EIO; return 0; case MTLOAD: ide_tape_discard_merge_buffer(drive, 0); idetape_create_load_unload_cmd(drive, &pc, IDETAPE_LU_LOAD_MASK); return idetape_queue_pc_tail(drive, &pc); case MTUNLOAD: case MTOFFL: /* * If door is locked, attempt to unlock before * attempting to eject. */ if (tape->door_locked) { if (!ide_tape_set_media_lock(drive, 0)) tape->door_locked = DOOR_UNLOCKED; } ide_tape_discard_merge_buffer(drive, 0); idetape_create_load_unload_cmd(drive, &pc, !IDETAPE_LU_LOAD_MASK); retval = idetape_queue_pc_tail(drive, &pc); if (!retval) clear_bit(IDE_AFLAG_MEDIUM_PRESENT, &drive->atapi_flags); return retval; case MTNOP: ide_tape_discard_merge_buffer(drive, 0); return idetape_flush_tape_buffers(drive); case MTRETEN: ide_tape_discard_merge_buffer(drive, 0); idetape_create_load_unload_cmd(drive, &pc, IDETAPE_LU_RETENSION_MASK | IDETAPE_LU_LOAD_MASK); return idetape_queue_pc_tail(drive, &pc); case MTEOM: idetape_create_space_cmd(&pc, 0, IDETAPE_SPACE_TO_EOD); return idetape_queue_pc_tail(drive, &pc); case MTERASE: (void)idetape_rewind_tape(drive); idetape_create_erase_cmd(&pc); return idetape_queue_pc_tail(drive, &pc); case MTSETBLK: if (mt_count) { if (mt_count < tape->blk_size || mt_count % tape->blk_size) return -EIO; tape->user_bs_factor = mt_count / tape->blk_size; clear_bit(IDE_AFLAG_DETECT_BS, &drive->atapi_flags); } else set_bit(IDE_AFLAG_DETECT_BS, &drive->atapi_flags); return 0; case MTSEEK: ide_tape_discard_merge_buffer(drive, 0); return idetape_position_tape(drive, mt_count * tape->user_bs_factor, tape->partition, 0); case MTSETPART: ide_tape_discard_merge_buffer(drive, 0); return idetape_position_tape(drive, 0, mt_count, 0); case MTFSR: case MTBSR: case MTLOCK: retval = ide_tape_set_media_lock(drive, 1); if (retval) return retval; tape->door_locked = DOOR_EXPLICITLY_LOCKED; return 0; case MTUNLOCK: retval = ide_tape_set_media_lock(drive, 0); if (retval) return retval; tape->door_locked = DOOR_UNLOCKED; return 0; default: printk(KERN_ERR "ide-tape: MTIO operation %d not supported\n", mt_op); return -EIO; } } /* * Our character device ioctls. General mtio.h magnetic io commands are * supported here, and not in the corresponding block interface. Our own * ide-tape ioctls are supported on both interfaces. */ static int idetape_chrdev_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg) { struct ide_tape_obj *tape = ide_tape_f(file); ide_drive_t *drive = tape->drive; struct mtop mtop; struct mtget mtget; struct mtpos mtpos; int block_offset = 0, position = tape->first_frame; void __user *argp = (void __user *)arg; debug_log(DBG_CHRDEV, "Enter %s, cmd=%u\n", __func__, cmd); if (tape->chrdev_dir == IDETAPE_DIR_WRITE) { ide_tape_flush_merge_buffer(drive); idetape_flush_tape_buffers(drive); } if (cmd == MTIOCGET || cmd == MTIOCPOS) { block_offset = tape->merge_bh_size / (tape->blk_size * tape->user_bs_factor); position = idetape_read_position(drive); if (position < 0) return -EIO; } switch (cmd) { case MTIOCTOP: if (copy_from_user(&mtop, argp, sizeof(struct mtop))) return -EFAULT; return idetape_mtioctop(drive, mtop.mt_op, mtop.mt_count); case MTIOCGET: memset(&mtget, 0, sizeof(struct mtget)); mtget.mt_type = MT_ISSCSI2; mtget.mt_blkno = position / tape->user_bs_factor - block_offset; mtget.mt_dsreg = ((tape->blk_size * tape->user_bs_factor) << MT_ST_BLKSIZE_SHIFT) & MT_ST_BLKSIZE_MASK; if (tape->drv_write_prot) mtget.mt_gstat |= GMT_WR_PROT(0xffffffff); if (copy_to_user(argp, &mtget, sizeof(struct mtget))) return -EFAULT; return 0; case MTIOCPOS: mtpos.mt_blkno = position / tape->user_bs_factor - block_offset; if (copy_to_user(argp, &mtpos, sizeof(struct mtpos))) return -EFAULT; return 0; default: if (tape->chrdev_dir == IDETAPE_DIR_READ) ide_tape_discard_merge_buffer(drive, 1); return idetape_blkdev_ioctl(drive, cmd, arg); } } /* * Do a mode sense page 0 with block descriptor and if it succeeds set the tape * block size with the reported value. */ static void ide_tape_get_bsize_from_bdesc(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc pc; idetape_create_mode_sense_cmd(&pc, IDETAPE_BLOCK_DESCRIPTOR); if (idetape_queue_pc_tail(drive, &pc)) { printk(KERN_ERR "ide-tape: Can't get block descriptor\n"); if (tape->blk_size == 0) { printk(KERN_WARNING "ide-tape: Cannot deal with zero " "block size, assuming 32k\n"); tape->blk_size = 32768; } return; } tape->blk_size = (pc.buf[4 + 5] << 16) + (pc.buf[4 + 6] << 8) + pc.buf[4 + 7]; tape->drv_write_prot = (pc.buf[2] & 0x80) >> 7; } static int idetape_chrdev_open(struct inode *inode, struct file *filp) { unsigned int minor = iminor(inode), i = minor & ~0xc0; ide_drive_t *drive; idetape_tape_t *tape; int retval; if (i >= MAX_HWIFS * MAX_DRIVES) return -ENXIO; lock_kernel(); tape = ide_tape_chrdev_get(i); if (!tape) { unlock_kernel(); return -ENXIO; } debug_log(DBG_CHRDEV, "Enter %s\n", __func__); /* * We really want to do nonseekable_open(inode, filp); here, but some * versions of tar incorrectly call lseek on tapes and bail out if that * fails. So we disallow pread() and pwrite(), but permit lseeks. */ filp->f_mode &= ~(FMODE_PREAD | FMODE_PWRITE); drive = tape->drive; filp->private_data = tape; if (test_and_set_bit(IDE_AFLAG_BUSY, &drive->atapi_flags)) { retval = -EBUSY; goto out_put_tape; } retval = idetape_wait_ready(drive, 60 * HZ); if (retval) { clear_bit(IDE_AFLAG_BUSY, &drive->atapi_flags); printk(KERN_ERR "ide-tape: %s: drive not ready\n", tape->name); goto out_put_tape; } idetape_read_position(drive); if (!test_bit(IDE_AFLAG_ADDRESS_VALID, &drive->atapi_flags)) (void)idetape_rewind_tape(drive); /* Read block size and write protect status from drive. */ ide_tape_get_bsize_from_bdesc(drive); /* Set write protect flag if device is opened as read-only. */ if ((filp->f_flags & O_ACCMODE) == O_RDONLY) tape->write_prot = 1; else tape->write_prot = tape->drv_write_prot; /* Make sure drive isn't write protected if user wants to write. */ if (tape->write_prot) { if ((filp->f_flags & O_ACCMODE) == O_WRONLY || (filp->f_flags & O_ACCMODE) == O_RDWR) { clear_bit(IDE_AFLAG_BUSY, &drive->atapi_flags); retval = -EROFS; goto out_put_tape; } } /* Lock the tape drive door so user can't eject. */ if (tape->chrdev_dir == IDETAPE_DIR_NONE) { if (!ide_tape_set_media_lock(drive, 1)) { if (tape->door_locked != DOOR_EXPLICITLY_LOCKED) tape->door_locked = DOOR_LOCKED; } } unlock_kernel(); return 0; out_put_tape: ide_tape_put(tape); unlock_kernel(); return retval; } static void idetape_write_release(ide_drive_t *drive, unsigned int minor) { idetape_tape_t *tape = drive->driver_data; ide_tape_flush_merge_buffer(drive); tape->merge_bh = ide_tape_kmalloc_buffer(tape, 1, 0); if (tape->merge_bh != NULL) { idetape_pad_zeros(drive, tape->blk_size * (tape->user_bs_factor - 1)); ide_tape_kfree_buffer(tape); tape->merge_bh = NULL; } idetape_write_filemark(drive); idetape_flush_tape_buffers(drive); idetape_flush_tape_buffers(drive); } static int idetape_chrdev_release(struct inode *inode, struct file *filp) { struct ide_tape_obj *tape = ide_tape_f(filp); ide_drive_t *drive = tape->drive; unsigned int minor = iminor(inode); lock_kernel(); tape = drive->driver_data; debug_log(DBG_CHRDEV, "Enter %s\n", __func__); if (tape->chrdev_dir == IDETAPE_DIR_WRITE) idetape_write_release(drive, minor); if (tape->chrdev_dir == IDETAPE_DIR_READ) { if (minor < 128) ide_tape_discard_merge_buffer(drive, 1); } if (minor < 128 && test_bit(IDE_AFLAG_MEDIUM_PRESENT, &drive->atapi_flags)) (void) idetape_rewind_tape(drive); if (tape->chrdev_dir == IDETAPE_DIR_NONE) { if (tape->door_locked == DOOR_LOCKED) { if (!ide_tape_set_media_lock(drive, 0)) tape->door_locked = DOOR_UNLOCKED; } } clear_bit(IDE_AFLAG_BUSY, &drive->atapi_flags); ide_tape_put(tape); unlock_kernel(); return 0; } static void idetape_get_inquiry_results(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc pc; char fw_rev[4], vendor_id[8], product_id[16]; idetape_create_inquiry_cmd(&pc); if (idetape_queue_pc_tail(drive, &pc)) { printk(KERN_ERR "ide-tape: %s: can't get INQUIRY results\n", tape->name); return; } memcpy(vendor_id, &pc.buf[8], 8); memcpy(product_id, &pc.buf[16], 16); memcpy(fw_rev, &pc.buf[32], 4); ide_fixstring(vendor_id, 8, 0); ide_fixstring(product_id, 16, 0); ide_fixstring(fw_rev, 4, 0); printk(KERN_INFO "ide-tape: %s <-> %s: %.8s %.16s rev %.4s\n", drive->name, tape->name, vendor_id, product_id, fw_rev); } /* * Ask the tape about its various parameters. In particular, we will adjust our * data transfer buffer size to the recommended value as returned by the tape. */ static void idetape_get_mode_sense_results(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; struct ide_atapi_pc pc; u8 *caps; u8 speed, max_speed; idetape_create_mode_sense_cmd(&pc, IDETAPE_CAPABILITIES_PAGE); if (idetape_queue_pc_tail(drive, &pc)) { printk(KERN_ERR "ide-tape: Can't get tape parameters - assuming" " some default values\n"); tape->blk_size = 512; put_unaligned(52, (u16 *)&tape->caps[12]); put_unaligned(540, (u16 *)&tape->caps[14]); put_unaligned(6*52, (u16 *)&tape->caps[16]); return; } caps = pc.buf + 4 + pc.buf[3]; /* convert to host order and save for later use */ speed = be16_to_cpup((__be16 *)&caps[14]); max_speed = be16_to_cpup((__be16 *)&caps[8]); *(u16 *)&caps[8] = max_speed; *(u16 *)&caps[12] = be16_to_cpup((__be16 *)&caps[12]); *(u16 *)&caps[14] = speed; *(u16 *)&caps[16] = be16_to_cpup((__be16 *)&caps[16]); if (!speed) { printk(KERN_INFO "ide-tape: %s: invalid tape speed " "(assuming 650KB/sec)\n", drive->name); *(u16 *)&caps[14] = 650; } if (!max_speed) { printk(KERN_INFO "ide-tape: %s: invalid max_speed " "(assuming 650KB/sec)\n", drive->name); *(u16 *)&caps[8] = 650; } memcpy(&tape->caps, caps, 20); if (caps[7] & 0x02) tape->blk_size = 512; else if (caps[7] & 0x04) tape->blk_size = 1024; } #ifdef CONFIG_IDE_PROC_FS #define ide_tape_devset_get(name, field) \ static int get_##name(ide_drive_t *drive) \ { \ idetape_tape_t *tape = drive->driver_data; \ return tape->field; \ } #define ide_tape_devset_set(name, field) \ static int set_##name(ide_drive_t *drive, int arg) \ { \ idetape_tape_t *tape = drive->driver_data; \ tape->field = arg; \ return 0; \ } #define ide_tape_devset_rw(_name, _min, _max, _field, _mulf, _divf) \ ide_tape_devset_get(_name, _field) \ ide_tape_devset_set(_name, _field) \ __IDE_DEVSET(_name, S_RW, _min, _max, get_##_name, set_##_name, _mulf, _divf) #define ide_tape_devset_r(_name, _min, _max, _field, _mulf, _divf) \ ide_tape_devset_get(_name, _field) \ __IDE_DEVSET(_name, S_READ, _min, _max, get_##_name, NULL, _mulf, _divf) static int mulf_tdsc(ide_drive_t *drive) { return 1000; } static int divf_tdsc(ide_drive_t *drive) { return HZ; } static int divf_buffer(ide_drive_t *drive) { return 2; } static int divf_buffer_size(ide_drive_t *drive) { return 1024; } ide_devset_rw(dsc_overlap, 0, 1, dsc_overlap); ide_tape_devset_rw(debug_mask, 0, 0xffff, debug_mask, NULL, NULL); ide_tape_devset_rw(tdsc, IDETAPE_DSC_RW_MIN, IDETAPE_DSC_RW_MAX, best_dsc_rw_freq, mulf_tdsc, divf_tdsc); ide_tape_devset_r(avg_speed, 0, 0xffff, avg_speed, NULL, NULL); ide_tape_devset_r(speed, 0, 0xffff, caps[14], NULL, NULL); ide_tape_devset_r(buffer, 0, 0xffff, caps[16], NULL, divf_buffer); ide_tape_devset_r(buffer_size, 0, 0xffff, buffer_size, NULL, divf_buffer_size); static const struct ide_devset *idetape_settings[] = { &ide_devset_avg_speed, &ide_devset_buffer, &ide_devset_buffer_size, &ide_devset_debug_mask, &ide_devset_dsc_overlap, &ide_devset_speed, &ide_devset_tdsc, NULL }; #endif /* * The function below is called to: * * 1. Initialize our various state variables. * 2. Ask the tape for its capabilities. * 3. Allocate a buffer which will be used for data transfer. The buffer size * is chosen based on the recommendation which we received in step 2. * * Note that at this point ide.c already assigned us an irq, so that we can * queue requests here and wait for their completion. */ static void idetape_setup(ide_drive_t *drive, idetape_tape_t *tape, int minor) { unsigned long t; int speed; int buffer_size; u8 gcw[2]; u16 *ctl = (u16 *)&tape->caps[12]; drive->pc_callback = ide_tape_callback; spin_lock_init(&tape->lock); drive->dsc_overlap = 1; if (drive->hwif->host_flags & IDE_HFLAG_NO_DSC) { printk(KERN_INFO "ide-tape: %s: disabling DSC overlap\n", tape->name); drive->dsc_overlap = 0; } /* Seagate Travan drives do not support DSC overlap. */ if (strstr((char *)&drive->id[ATA_ID_PROD], "Seagate STT3401")) drive->dsc_overlap = 0; tape->minor = minor; tape->name[0] = 'h'; tape->name[1] = 't'; tape->name[2] = '0' + minor; tape->chrdev_dir = IDETAPE_DIR_NONE; *((u16 *)&gcw) = drive->id[ATA_ID_CONFIG]; /* Command packet DRQ type */ if (((gcw[0] & 0x60) >> 5) == 1) set_bit(IDE_AFLAG_DRQ_INTERRUPT, &drive->atapi_flags); idetape_get_inquiry_results(drive); idetape_get_mode_sense_results(drive); ide_tape_get_bsize_from_bdesc(drive); tape->user_bs_factor = 1; tape->buffer_size = *ctl * tape->blk_size; while (tape->buffer_size > 0xffff) { printk(KERN_NOTICE "ide-tape: decreasing stage size\n"); *ctl /= 2; tape->buffer_size = *ctl * tape->blk_size; } buffer_size = tape->buffer_size; tape->pages_per_buffer = buffer_size / PAGE_SIZE; if (buffer_size % PAGE_SIZE) { tape->pages_per_buffer++; tape->excess_bh_size = PAGE_SIZE - buffer_size % PAGE_SIZE; } /* select the "best" DSC read/write polling freq */ speed = max(*(u16 *)&tape->caps[14], *(u16 *)&tape->caps[8]); t = (IDETAPE_FIFO_THRESHOLD * tape->buffer_size * HZ) / (speed * 1000); /* * Ensure that the number we got makes sense; limit it within * IDETAPE_DSC_RW_MIN and IDETAPE_DSC_RW_MAX. */ tape->best_dsc_rw_freq = clamp_t(unsigned long, t, IDETAPE_DSC_RW_MIN, IDETAPE_DSC_RW_MAX); printk(KERN_INFO "ide-tape: %s <-> %s: %dKBps, %d*%dkB buffer, " "%lums tDSC%s\n", drive->name, tape->name, *(u16 *)&tape->caps[14], (*(u16 *)&tape->caps[16] * 512) / tape->buffer_size, tape->buffer_size / 1024, tape->best_dsc_rw_freq * 1000 / HZ, drive->using_dma ? ", DMA":""); ide_proc_register_driver(drive, tape->driver); } static void ide_tape_remove(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; ide_proc_unregister_driver(drive, tape->driver); ide_unregister_region(tape->disk); ide_tape_put(tape); } static void ide_tape_release(struct kref *kref) { struct ide_tape_obj *tape = to_ide_tape(kref); ide_drive_t *drive = tape->drive; struct gendisk *g = tape->disk; BUG_ON(tape->merge_bh_size); drive->dsc_overlap = 0; drive->driver_data = NULL; device_destroy(idetape_sysfs_class, MKDEV(IDETAPE_MAJOR, tape->minor)); device_destroy(idetape_sysfs_class, MKDEV(IDETAPE_MAJOR, tape->minor + 128)); idetape_devs[tape->minor] = NULL; g->private_data = NULL; put_disk(g); kfree(tape); } #ifdef CONFIG_IDE_PROC_FS static int proc_idetape_read_name (char *page, char **start, off_t off, int count, int *eof, void *data) { ide_drive_t *drive = (ide_drive_t *) data; idetape_tape_t *tape = drive->driver_data; char *out = page; int len; len = sprintf(out, "%s\n", tape->name); PROC_IDE_READ_RETURN(page, start, off, count, eof, len); } static ide_proc_entry_t idetape_proc[] = { { "capacity", S_IFREG|S_IRUGO, proc_ide_read_capacity, NULL }, { "name", S_IFREG|S_IRUGO, proc_idetape_read_name, NULL }, { NULL, 0, NULL, NULL } }; #endif static int ide_tape_probe(ide_drive_t *); static ide_driver_t idetape_driver = { .gen_driver = { .owner = THIS_MODULE, .name = "ide-tape", .bus = &ide_bus_type, }, .probe = ide_tape_probe, .remove = ide_tape_remove, .version = IDETAPE_VERSION, .media = ide_tape, .do_request = idetape_do_request, .end_request = idetape_end_request, .error = __ide_error, #ifdef CONFIG_IDE_PROC_FS .proc = idetape_proc, .settings = idetape_settings, #endif }; /* Our character device supporting functions, passed to register_chrdev. */ static const struct file_operations idetape_fops = { .owner = THIS_MODULE, .read = idetape_chrdev_read, .write = idetape_chrdev_write, .ioctl = idetape_chrdev_ioctl, .open = idetape_chrdev_open, .release = idetape_chrdev_release, }; static int idetape_open(struct inode *inode, struct file *filp) { struct gendisk *disk = inode->i_bdev->bd_disk; struct ide_tape_obj *tape; tape = ide_tape_get(disk); if (!tape) return -ENXIO; return 0; } static int idetape_release(struct inode *inode, struct file *filp) { struct gendisk *disk = inode->i_bdev->bd_disk; struct ide_tape_obj *tape = ide_tape_g(disk); ide_tape_put(tape); return 0; } static int idetape_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg) { struct block_device *bdev = inode->i_bdev; struct ide_tape_obj *tape = ide_tape_g(bdev->bd_disk); ide_drive_t *drive = tape->drive; int err = generic_ide_ioctl(drive, file, bdev, cmd, arg); if (err == -EINVAL) err = idetape_blkdev_ioctl(drive, cmd, arg); return err; } static struct block_device_operations idetape_block_ops = { .owner = THIS_MODULE, .open = idetape_open, .release = idetape_release, .ioctl = idetape_ioctl, }; static int ide_tape_probe(ide_drive_t *drive) { idetape_tape_t *tape; struct gendisk *g; int minor; if (!strstr("ide-tape", drive->driver_req)) goto failed; if (drive->media != ide_tape) goto failed; if (drive->id_read == 1 && !ide_check_atapi_device(drive, DRV_NAME)) { printk(KERN_ERR "ide-tape: %s: not supported by this version of" " the driver\n", drive->name); goto failed; } tape = kzalloc(sizeof(idetape_tape_t), GFP_KERNEL); if (tape == NULL) { printk(KERN_ERR "ide-tape: %s: Can't allocate a tape struct\n", drive->name); goto failed; } g = alloc_disk(1 << PARTN_BITS); if (!g) goto out_free_tape; ide_init_disk(g, drive); kref_init(&tape->kref); tape->drive = drive; tape->driver = &idetape_driver; tape->disk = g; g->private_data = &tape->driver; drive->driver_data = tape; mutex_lock(&idetape_ref_mutex); for (minor = 0; idetape_devs[minor]; minor++) ; idetape_devs[minor] = tape; mutex_unlock(&idetape_ref_mutex); idetape_setup(drive, tape, minor); device_create_drvdata(idetape_sysfs_class, &drive->gendev, MKDEV(IDETAPE_MAJOR, minor), NULL, "%s", tape->name); device_create_drvdata(idetape_sysfs_class, &drive->gendev, MKDEV(IDETAPE_MAJOR, minor + 128), NULL, "n%s", tape->name); g->fops = &idetape_block_ops; ide_register_region(g); return 0; out_free_tape: kfree(tape); failed: return -ENODEV; } static void __exit idetape_exit(void) { driver_unregister(&idetape_driver.gen_driver); class_destroy(idetape_sysfs_class); unregister_chrdev(IDETAPE_MAJOR, "ht"); } static int __init idetape_init(void) { int error = 1; idetape_sysfs_class = class_create(THIS_MODULE, "ide_tape"); if (IS_ERR(idetape_sysfs_class)) { idetape_sysfs_class = NULL; printk(KERN_ERR "Unable to create sysfs class for ide tapes\n"); error = -EBUSY; goto out; } if (register_chrdev(IDETAPE_MAJOR, "ht", &idetape_fops)) { printk(KERN_ERR "ide-tape: Failed to register chrdev" " interface\n"); error = -EBUSY; goto out_free_class; } error = driver_register(&idetape_driver.gen_driver); if (error) goto out_free_driver; return 0; out_free_driver: driver_unregister(&idetape_driver.gen_driver); out_free_class: class_destroy(idetape_sysfs_class); out: return error; } MODULE_ALIAS("ide:*m-tape*"); module_init(idetape_init); module_exit(idetape_exit); MODULE_ALIAS_CHARDEV_MAJOR(IDETAPE_MAJOR); MODULE_DESCRIPTION("ATAPI Streaming TAPE Driver"); MODULE_LICENSE("GPL");