#ifndef __ALPHA_JENSEN_H
#define __ALPHA_JENSEN_H

#include <asm/compiler.h>

/*
 * Defines for the AlphaPC EISA IO and memory address space.
 */

/*
 * NOTE! The memory operations do not set any memory barriers, as it's
 * not needed for cases like a frame buffer that is essentially memory-like.
 * You need to do them by hand if the operations depend on ordering.
 *
 * Similarly, the port IO operations do a "mb" only after a write operation:
 * if an mb is needed before (as in the case of doing memory mapped IO
 * first, and then a port IO operation to the same device), it needs to be
 * done by hand.
 *
 * After the above has bitten me 100 times, I'll give up and just do the
 * mb all the time, but right now I'm hoping this will work out.  Avoiding
 * mb's may potentially be a noticeable speed improvement, but I can't
 * honestly say I've tested it.
 *
 * Handling interrupts that need to do mb's to synchronize to non-interrupts
 * is another fun race area.  Don't do it (because if you do, I'll have to
 * do *everything* with interrupts disabled, ugh).
 */

/*
 * EISA Interrupt Acknowledge address
 */
#define EISA_INTA		(IDENT_ADDR + 0x100000000UL)

/*
 * FEPROM addresses
 */
#define EISA_FEPROM0		(IDENT_ADDR + 0x180000000UL)
#define EISA_FEPROM1		(IDENT_ADDR + 0x1A0000000UL)

/*
 * VL82C106 base address
 */
#define EISA_VL82C106		(IDENT_ADDR + 0x1C0000000UL)

/*
 * EISA "Host Address Extension" address (bits 25-31 of the EISA address)
 */
#define EISA_HAE		(IDENT_ADDR + 0x1D0000000UL)

/*
 * "SYSCTL" register address
 */
#define EISA_SYSCTL		(IDENT_ADDR + 0x1E0000000UL)

/*
 * "spare" register address
 */
#define EISA_SPARE		(IDENT_ADDR + 0x1F0000000UL)

/*
 * EISA memory address offset
 */
#define EISA_MEM		(IDENT_ADDR + 0x200000000UL)

/*
 * EISA IO address offset
 */
#define EISA_IO			(IDENT_ADDR + 0x300000000UL)


#ifdef __KERNEL__

#ifndef __EXTERN_INLINE
#define __EXTERN_INLINE extern inline
#define __IO_EXTERN_INLINE
#endif

/*
 * Handle the "host address register". This needs to be set
 * to the high 7 bits of the EISA address.  This is also needed
 * for EISA IO addresses, which are only 16 bits wide (the
 * hae needs to be set to 0).
 *
 * HAE isn't needed for the local IO operations, though.
 */

#define JENSEN_HAE_ADDRESS	EISA_HAE
#define JENSEN_HAE_MASK		0x1ffffff

__EXTERN_INLINE void jensen_set_hae(unsigned long addr)
{
	/* hae on the Jensen is bits 31:25 shifted right */
	addr >>= 25;
	if (addr != alpha_mv.hae_cache)
		set_hae(addr);
}

#define vuip	volatile unsigned int *

/*
 * IO functions
 *
 * The "local" functions are those that don't go out to the EISA bus,
 * but instead act on the VL82C106 chip directly.. This is mainly the
 * keyboard, RTC,  printer and first two serial lines..
 *
 * The local stuff makes for some complications, but it seems to be
 * gone in the PCI version. I hope I can get DEC suckered^H^H^H^H^H^H^H^H
 * convinced that I need one of the newer machines.
 */

static inline unsigned int jensen_local_inb(unsigned long addr)
{
	return 0xff & *(vuip)((addr << 9) + EISA_VL82C106);
}

static inline void jensen_local_outb(u8 b, unsigned long addr)
{
	*(vuip)((addr << 9) + EISA_VL82C106) = b;
	mb();
}

static inline unsigned int jensen_bus_inb(unsigned long addr)
{
	long result;

	jensen_set_hae(0);
	result = *(volatile int *)((addr << 7) + EISA_IO + 0x00);
	return __kernel_extbl(result, addr & 3);
}

static inline void jensen_bus_outb(u8 b, unsigned long addr)
{
	jensen_set_hae(0);
	*(vuip)((addr << 7) + EISA_IO + 0x00) = b * 0x01010101;