/* * linux/arch/arm/mach-at91/board-sam9-l9260.c * * Copyright (C) 2005 SAN People * Copyright (C) 2006 Atmel * Copyright (C) 2007 Olimex Ltd * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include <linux/types.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> #include <linux/platform_device.h> #include <linux/spi/spi.h> #include <mach/hardware.h> #include <asm/setup.h> #include <asm/mach-types.h> #include <asm/irq.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <asm/mach/irq.h> #include <mach/board.h> #include <mach/gpio.h> #include <mach/at91sam9_smc.h> #include "sam9_smc.h" #include "generic.h" static void __init ek_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ at91sam9260_initialize(18432000); /* Setup the LEDs */ at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6); /* DBGU on ttyS0. (Rx & Tx only) */ at91_register_uart(0, 0, 0); /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD | ATMEL_UART_RI); /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); /* set serial console to ttyS0 (ie, DBGU) */ at91_set_serial_console(0); } static void __init ek_init_irq(void) { at91sam9260_init_interrupts(NULL); } /* * USB Host port */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, }; /* * USB Device port */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PC5, .pullup_pin = 0, /* pull-up driven by UDC */ }; /* * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { #if !defined(CONFIG_MMC_AT91) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, .max_speed_hz = 15 * 1000 * 1000, .bus_num = 0, }, #if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) { /* DataFlash card */ .modalias = "mtd_dataflash", .chip_select = 0, .max_speed_hz = 15 * 1000 * 1000, .bus_num = 0, }, #endif #endif }; /* * MACB Ethernet device */ static struct at91_eth_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PA7, .is_rmii = 0, }; /* * NAND flash */ static struct mtd_partition __initdata ek_nand_partition[] = { { .name = "Bootloader Area", .offset = 0, .size = 10 * SZ_1M, }, { .name = "User Area", .offset = MTDPART_OFS_NXTBLK, .size = MTDPART_SIZ_FULL, }, }; static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) { *num_partitions = ARRAY_SIZE(ek_nand_partition); return ek_nand_partition; } static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, // .det_pin = ... not connected .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .partition_info = nand_partitions, }; static struct sam9_smc_config __initdata ek_nand_smc_config = { .ncs_read_setup = 0, .nrd_setup = 1, .ncs_write_setup = 0, .nwe_setup = 1, .ncs_read_pulse = 3, .nrd_pulse = 3, .ncs_write_pulse = 3, .nwe_pulse = 3, .read_cycle = 5, .write_cycle = 5, .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8, .tdf_cycles = 2, }; static void __init ek_add_device_nand(void) { /* configure chip-select 3 (NAND) */ sam9_smc_configure(3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } /* * MCI (SD/MMC) */ static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, .det_pin = AT91_PIN_PC8, .wp_pin = AT91_PIN_PC4, // .vcc_pin = ... not connected }; static void __init ek_board_init(void) { /* Serial */ at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); /* USB Device */ at91_add_device_udc(&ek_udc_data); /* SPI */ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); /* NAND */ ek_add_device_nand(); /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ at91_add_device_mmc(0, &ek_mmc_data); /* I2C */ at91_add_device_i2c(NULL, 0); } MACHINE_START(SAM9_L9260, "Olimex SAM9-L9260") /* Maintainer: Olimex */ .phys_io = AT91_BASE_SYS, .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, .init_irq = ek_init_irq, .init_machine = ek_board_init, MACHINE_END