ThinkPad ACPI Extras Driver Version 0.14 April 21st, 2007 Borislav Deianov <borislav@users.sf.net> Henrique de Moraes Holschuh <hmh@hmh.eng.br> http://ibm-acpi.sf.net/ This is a Linux driver for the IBM and Lenovo ThinkPad laptops. It supports various features of these laptops which are accessible through the ACPI and ACPI EC framework, but not otherwise fully supported by the generic Linux ACPI drivers. This driver used to be named ibm-acpi until kernel 2.6.21 and release 0.13-20070314. It used to be in the drivers/acpi tree, but it was moved to the drivers/misc tree and renamed to thinkpad-acpi for kernel 2.6.22, and release 0.14. Status ------ The features currently supported are the following (see below for detailed description): - Fn key combinations - Bluetooth enable and disable - video output switching, expansion control - ThinkLight on and off - limited docking and undocking - UltraBay eject - CMOS control - LED control - ACPI sounds - temperature sensors - Experimental: embedded controller register dump - LCD brightness control - Volume control - Fan control and monitoring: fan speed, fan enable/disable - Experimental: WAN enable and disable A compatibility table by model and feature is maintained on the web site, http://ibm-acpi.sf.net/. I appreciate any success or failure reports, especially if they add to or correct the compatibility table. Please include the following information in your report: - ThinkPad model name - a copy of your DSDT, from /proc/acpi/dsdt - a copy of the output of dmidecode, with serial numbers and UUIDs masked off - which driver features work and which don't - the observed behavior of non-working features Any other comments or patches are also more than welcome. Installation ------------ If you are compiling this driver as included in the Linux kernel sources, simply enable the CONFIG_THINKPAD_ACPI option, and optionally enable the CONFIG_THINKPAD_ACPI_BAY option if you want the thinkpad-specific bay functionality. Features -------- The driver exports two different interfaces to userspace, which can be used to access the features it provides. One is a legacy procfs-based interface, which will be removed at some time in the distant future. The other is a new sysfs-based interface which is not complete yet. The procfs interface creates the /proc/acpi/ibm directory. There is a file under that directory for each feature it supports. The procfs interface is mostly frozen, and will change very little if at all: it will not be extended to add any new functionality in the driver, instead all new functionality will be implemented on the sysfs interface. The sysfs interface tries to blend in the generic Linux sysfs subsystems and classes as much as possible. Since some of these subsystems are not yet ready or stabilized, it is expected that this interface will change, and any and all userspace programs must deal with it. Notes about the sysfs interface: Unlike what was done with the procfs interface, correctness when talking to the sysfs interfaces will be enforced, as will correctness in the thinkpad-acpi's implementation of sysfs interfaces. Also, any bugs in the thinkpad-acpi sysfs driver code or in the thinkpad-acpi's implementation of the sysfs interfaces will be fixed for maximum correctness, even if that means changing an interface in non-compatible ways. As these interfaces mature both in the kernel and in thinkpad-acpi, such changes should become quite rare. Applications interfacing to the thinkpad-acpi sysfs interfaces must follow all sysfs guidelines and correctly process all errors (the sysfs interface makes extensive use of errors). File descriptors and open / close operations to the sysfs inodes must also be properly implemented. The version of thinkpad-acpi's sysfs interface is exported by the driver as a driver attribute (see below). Sysfs driver attributes are on the driver's sysfs attribute space, for 2.6.20 this is /sys/bus/platform/drivers/thinkpad-acpi/. Sysfs device attributes are on the driver's sysfs attribute space, for 2.6.20 this is /sys/devices/platform/thinkpad-acpi/. Driver version -------------- procfs: /proc/acpi/ibm/driver sysfs driver attribute: version The driver name and version. No commands can be written to this file. Sysfs interface version ----------------------- sysfs driver attribute: interface_version Version of the thinkpad-acpi sysfs interface, as an unsigned long (output in hex format: 0xAAAABBCC), where: AAAA - major revision BB - minor revision CC - bugfix revision The sysfs interface version changelog for the driver can be found at the end of this document. Changes to the sysfs interface done by the kernel subsystems are not documented here, nor are they tracked by this attribute. Hot keys -------- procfs: /proc/acpi/ibm/hotkey sysfs device attribute: hotkey_* Without this driver, only the Fn-F4 key (sleep button) generates an ACPI event. With the driver loaded, the hotkey feature enabled and the mask set (see below), the various hot keys generate ACPI events in the following format: ibm/hotkey HKEY 00000080 0000xxxx The last four digits vary depending on the key combination pressed. All labeled Fn-Fx key combinations generate distinct events. In addition, the lid microswitch and some docking station buttons may also generate such events. The bit mask allows some control over which hot keys generate ACPI events. Not all bits in the mask can be modified. Not all bits that can be modified do anything. Not all hot keys can be individually controlled by the mask. Most recent ThinkPad models honor the following bits (assuming the hot keys feature has been enabled): key bit behavior when set behavior when unset Fn-F3 always generates ACPI event Fn-F4 always generates ACPI event Fn-F5 0010 generate ACPI event enable/disable Bluetooth Fn-F7 0040 generate ACPI event switch LCD and external display Fn-F8 0080 generate ACPI event expand screen or none Fn-F9 0100 generate ACPI event none Fn-F12 always generates ACPI event Some models do not support all of the above. For example, the T30 does not support Fn-F5 and Fn-F9. Other models do not support the mask at all. On those models, hot keys cannot be controlled individually. Note that enabling ACPI events for some keys prevents their default behavior. For example, if events for Fn-F5 are enabled, that key will no longer enable/disable Bluetooth by itself. This can still be done from an acpid handler for the ibm/hotkey event. Note also that not all Fn key combinations are supported through ACPI. For example, on the X40, the brightness, volume and "Access IBM" buttons do not generate ACPI events even with this driver. They *can* be used through the "ThinkPad Buttons" utility, see http://www.nongnu.org/tpb/ procfs notes: The following commands can be written to the /proc/acpi/ibm/hotkey file: echo enable > /proc/acpi/ibm/hotkey -- enable the hot keys feature echo disable > /proc/acpi/ibm/hotkey -- disable the hot keys feature echo 0xffff > /proc/acpi/ibm/hotkey -- enable all possible hot keys echo 0x0000 > /proc/acpi/ibm/hotkey -- disable all possible hot keys ... any other 4-hex-digit mask ... echo reset > /proc/acpi/ibm/hotkey -- restore the original mask sysfs notes: hotkey_bios_enabled: Returns the status of the hot keys feature when thinkpad-acpi was loaded. Upon module unload, the hot key feature status will be restored to this value. 0: hot keys were disabled 1: hot keys were enabled hotkey_bios_mask: Returns the hot keys mask when thinkpad-acpi was loaded. Upon module unload, the hot keys mask will be restored to this value. hotkey_enable: Enables/disables the hot keys feature, and reports current status of the hot keys feature. 0: disables the hot keys feature / feature disabled 1: enables the hot keys feature / feature enabled hotkey_mask: bit mask to enable ACPI event generation for each hot key (see above). Returns the current status of the hot keys mask, and allows one to modify it. Bluetooth --------- procfs: /proc/acpi/ibm/bluetooth sysfs device attribute: bluetooth_enable This feature shows the presence and current state of a ThinkPad Bluetooth device in the internal ThinkPad CDC slot. Procfs notes: If Bluetooth is installed, the following commands can be used: echo enable > /proc/acpi/ibm/bluetooth echo disable > /proc/acpi/ibm/bluetooth Sysfs notes: If the Bluetooth CDC card is installed, it can be enabled / disabled through the "bluetooth_enable" thinkpad-acpi device attribute, and its current status can also be queried. enable: 0: disables Bluetooth / Bluetooth is disabled 1: enables Bluetooth / Bluetooth is enabled. Note: this interface will be probably be superseeded by the generic rfkill class, so it is NOT to be considered stable yet. Video output control -- /proc/acpi/ibm/video -------------------------------------------- This feature allows control over the devices used for video output - LCD, CRT or DVI (if available). The following commands are available: echo lcd_enable > /proc/acpi/ibm/video echo lcd_disable > /proc/acpi/ibm/video echo crt_enable > /proc/acpi/ibm/video echo crt_disable > /proc/acpi/ibm/video echo dvi_enable > /proc/acpi/ibm/video echo dvi_disable > /proc/acpi/ibm/video echo auto_enable > /proc/acpi/ibm/video echo auto_disable > /proc/acpi/ibm/video echo expand_toggle > /proc/acpi/ibm/video echo video_switch > /proc/acpi/ibm/video Each video output device can be enabled or disabled individually. Reading /proc/acpi/ibm/video shows the status of each device. Automatic video switching can be enabled or disabled. When automatic video switching is enabled, certain events (e.g. opening the lid, docking or undocking) cause the video output device to change automatically. While this can be useful, it also causes flickering and, on the X40, video corruption. By disabling automatic switching, the flickering or video corruption can be avoided. The video_switch command cycles through the available video outputs (it simulates the behavior of Fn-F7). Video expansion can be toggled through this feature. This controls whether the display is expanded to fill the entire LCD screen when a mode with less than full resolution is used. Note that the current video expansion status cannot be determined through this feature. Note that on many models (particularly those using Radeon graphics chips) the X driver configures the video card in a way which prevents Fn-F7 from working. This also disables the video output switching features of this driver, as it uses the same ACPI methods as Fn-F7. Video switching on the console should still work. UPDATE: There's now a patch for the X.org Radeon driver which addresses this issue. Some people are reporting success with the patch while others are still having problems. For more information: https://bugs.freedesktop.org/show_bug.cgi?id=2000 ThinkLight control -- /proc/acpi/ibm/light ------------------------------------------ The current status of the ThinkLight can be found in this file. A few models which do not make the status available will show it as "unknown". The available commands are: echo on > /proc/acpi/ibm/light echo off > /proc/acpi/ibm/light Docking / undocking -- /proc/acpi/ibm/dock ------------------------------------------ Docking and undocking (e.g. with the X4 UltraBase) requires some actions to be taken by the operating system to safely make or break the electrical connections with the dock. The docking feature of this driver generates the following ACPI events: ibm/dock GDCK 00000003 00000001 -- eject request ibm/dock GDCK 00000003 00000002 -- undocked ibm/dock GDCK 00000000 00000003 -- docked NOTE: These events will only be generated if the laptop was docked when originally booted. This is due to the current lack of support for hot plugging of devices in the Linux ACPI framework. If the laptop was booted while not in the dock, the following message is shown in the logs: Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present In this case, no dock-related events are generated but the dock and undock commands described below still work. They can be executed manually or triggered by Fn key combinations (see the example acpid configuration files included in the driver tarball package available on the web site). When the eject request button on the dock is pressed, the first event above is generated. The handler for this event should issue the following command: echo undock > /proc/acpi/ibm/dock After the LED on the dock goes off, it is safe to eject the laptop. Note: if you pressed this key by mistake, go ahead and eject the laptop, then dock it back in. Otherwise, the dock may not function as expected. When the laptop is docked, the third event above is generated. The handler for this event should issue the following command to fully enable the dock: echo dock > /proc/acpi/ibm/dock The contents of the /proc/acpi/ibm/dock file shows the current status of the dock, as provided by the ACPI framework. The docking support in this driver does not take care of enabling or disabling any other devices you may have attached to the dock. For example, a CD drive plugged into the UltraBase needs to be disabled or enabled separately. See the provided example acpid configuration files for how this can be accomplished. There is no support yet for PCI devices that may be attached to a docking station, e.g. in the ThinkPad Dock II. The driver currently does not recognize, enable or disable such devices. This means that the only docking stations currently supported are the X-series UltraBase docks and "dumb" port replicators like the Mini Dock (the latter don't need any ACPI support, actually). UltraBay eject -- /proc/acpi/ibm/bay ------------------------------------ Inserting or ejecting an UltraBay device requires some actions to be taken by the operating system to safely make or break the electrical connections with the device. This feature generates the following ACPI events: ibm/bay MSTR 00000003 00000000 -- eject request ibm/bay MSTR 00000001 00000000 -- eject lever inserted NOTE: These events will only be generated if the UltraBay was present when the laptop was originally booted (on the X series, the UltraBay is in the dock, so it may not be present if the laptop was undocked). This is due to the current lack of support for hot plugging of devices in the Linux ACPI framework. If the laptop was booted without the UltraBay, the following message is shown in the logs: Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present In this case, no bay-related events are generated but the eject command described below still works. It can be executed manually or triggered by a hot key combination. Sliding the eject lever generates the first event shown above. The handler for this event should take whatever actions are necessary to shut down the device in the UltraBay (e.g. call idectl), then issue the following command: echo eject > /proc/acpi/ibm/bay After the LED on the UltraBay goes off, it is safe to pull out the device. When the eject lever is inserted, the second event above is generated. The handler for this event should take whatever actions are necessary to enable the UltraBay device (e.g. call idectl). The contents of the /proc/acpi/ibm/bay file shows the current status of the UltraBay, as provided by the ACPI framework. EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use this feature, you need to supply the experimental=1 parameter when loading the module): These models do not have a button near the UltraBay device to request a hot eject but rather require the laptop to be put to sleep (suspend-to-ram) before the bay device is ejected or inserted). The sequence of steps to eject the device is as follows: echo eject > /proc/acpi/ibm/bay put the ThinkPad to sleep remove the drive resume from sleep cat /proc/acpi/ibm/bay should show that the drive was removed On the A3x, both the UltraBay 2000 and UltraBay Plus devices are supported. Use "eject2" instead of "eject" for the second bay. Note: the UltraBay eject support on the 600e/x, A22p and A3x is EXPERIMENTAL and may not work as expected. USE WITH CAUTION! CMOS control ------------ procfs: /proc/acpi/ibm/cmos sysfs device attribute: cmos_command This feature is used internally by the ACPI firmware to control the ThinkLight on most newer ThinkPad models. It may also control LCD brightness, sounds volume and more, but only on some models. The range of valid cmos command numbers is 0 to 21, but not all have an effect and the behavior varies from model to model. Here is the behavior on the X40 (tpb is the ThinkPad Buttons utility): 0 - no effect but tpb reports "Volume down" 1 - no effect but tpb reports "Volume up" 2 - no effect but tpb reports "Mute on" 3 - simulate pressing the "Access IBM" button 4 - LCD brightness up 5 - LCD brightness down 11 - toggle screen expansion 12 - ThinkLight on 13 - ThinkLight off 14 - no effect but tpb reports ThinkLight status change The cmos command interface is prone to firmware split-brain problems, as in newer ThinkPads it is just a compatibility layer. LED control -- /proc/acpi/ibm/led --------------------------------- Some of the LED indicators can be controlled through this feature. The available commands are: echo '<led number> on' >/proc/acpi/ibm/led echo '<led number> off' >/proc/acpi/ibm/led echo '<led number> blink' >/proc/acpi/ibm/led The <led number> range is 0 to 7. The set of LEDs that can be controlled varies from model to model. Here is the mapping on the X40: 0 - power 1 - battery (orange) 2 - battery (green) 3 - UltraBase 4 - UltraBay 7 - standby All of the above can be turned on and off and can be made to blink. ACPI sounds -- /proc/acpi/ibm/beep ---------------------------------- The BEEP method is used internally by the ACPI firmware to provide audible alerts in various situations. This feature allows the same sounds to be triggered manually. The commands are non-negative integer numbers: echo <number> >/proc/acpi/ibm/beep The valid <number> range is 0 to 17. Not all numbers trigger sounds and the sounds vary from model to model. Here is the behavior on the X40: 0 - stop a sound in progress (but use 17 to stop 16) 2 - two beeps, pause, third beep ("low battery") 3 - single beep 4 - high, followed by low-pitched beep ("unable") 5 - single beep 6 - very high, followed by high-pitched beep ("AC/DC") 7 - high-pitched beep 9 - three short beeps 10 - very long beep 12 - low-pitched beep 15 - three high-pitched beeps repeating constantly, stop with 0 16 - one medium-pitched beep repeating constantly, stop with 17 17 - stop 16 Temperature sensors ------------------- procfs: /proc/acpi/ibm/thermal sysfs device attributes: (hwmon) temp*_input Most ThinkPads include six or more separate temperature sensors but only expose the CPU temperature through the standard ACPI methods. This feature shows readings from up to eight different sensors on older ThinkPads, and it has experimental support for up to sixteen different sensors on newer ThinkPads. EXPERIMENTAL: The 16-sensors feature is marked EXPERIMENTAL because the implementation directly accesses hardware registers and may not work as expected. USE WITH CAUTION! To use this feature, you need to supply the experimental=1 parameter when loading the module. When EXPERIMENTAL mode is enabled, reading the first 8 sensors on newer ThinkPads will also use an new experimental thermal sensor access mode. For example, on the X40, a typical output may be: temperatures: 42 42 45 41 36 -128 33 -128 EXPERIMENTAL: On the T43/p, a typical output may be: temperatures: 48 48 36 52 38 -128 31 -128 48 52 48 -128 -128 -128 -128 -128 The mapping of thermal sensors to physical locations varies depending on system-board model (and thus, on ThinkPad model). http://thinkwiki.org/wiki/Thermal_Sensors is a public wiki page that tries to track down these locations for various models. Most (newer?) models seem to follow this pattern: 1: CPU 2: (depends on model) 3: (depends on model) 4: GPU 5: Main battery: main sensor 6: Bay battery: main sensor 7: Main battery: secondary sensor 8: Bay battery: secondary sensor 9-15: (depends on model) For the R51 (source: Thomas Gruber): 2: Mini-PCI 3: Internal HDD For the T43, T43/p (source: Shmidoax/Thinkwiki.org) http://thinkwiki.org/wiki/Thermal_Sensors#ThinkPad_T43.2C_T43p 2: System board, left side (near PCMCIA slot), reported as HDAPS temp 3: PCMCIA slot 9: MCH (northbridge) to DRAM Bus 10: ICH (southbridge), under Mini-PCI card, under touchpad 11: Power regulator, underside of system board, below F2 key The A31 has a very atypical layout for the thermal sensors (source: Milos Popovic, http://thinkwiki.org/wiki/Thermal_Sensors#ThinkPad_A31) 1: CPU 2: Main Battery: main sensor 3: Power Converter 4: Bay Battery: main sensor 5: MCH (northbridge) 6: PCMCIA/ambient 7: Main Battery: secondary sensor 8: Bay Battery: secondary sensor Procfs notes: Readings from sensors that are not available return -128. No commands can be written to this file. Sysfs notes: Sensors that are not available return the ENXIO error. This status may change at runtime, as there are hotplug thermal sensors, like those inside the batteries and docks. thinkpad-acpi thermal sensors are reported through the hwmon subsystem, and follow all of the hwmon guidelines at Documentation/hwmon. EXPERIMENTAL: Embedded controller register dump -- /proc/acpi/ibm/ecdump ------------------------------------------------------------------------ This feature is marked EXPERIMENTAL because the implementation directly accesses hardware registers and may not work as expected. USE WITH CAUTION! To use this feature, you need to supply the experimental=1 parameter when loading the module. This feature dumps the values of 256 embedded controller registers. Values which have changed since the last time the registers were dumped are marked with a star: [root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00 EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00 EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80 EC 0x30: 01 07 1a 00 30 04 00 00 *85 00 00 10 00 50 00 00 EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00 EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 *bc *02 *bc EC 0x60: *02 *bc *02 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0x70: 00 00 00 00 00 12 30 40 *24 *26 *2c *27 *20 80 *1f 80 EC 0x80: 00 00 00 06 *37 *0e 03 00 00 00 0e 07 00 00 00 00 EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0xa0: *ff 09 ff 09 ff ff *64 00 *00 *00 *a2 41 *ff *ff *e0 00 EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03 EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a This feature can be used to determine the register holding the fan speed on some models. To do that, do the following: - make sure the battery is fully charged - make sure the fan is running - run 'cat /proc/acpi/ibm/ecdump' several times, once per second or so The first step makes sure various charging-related values don't vary. The second ensures that the fan-related values do vary, since the fan speed fluctuates a bit. The third will (hopefully) mark the fan register with a star: [root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00 EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00 EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80 EC 0x30: 01 07 1a 00 30 04 00 00 85 00 00 10 00 50 00 00 EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00 EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 bc 02 bc EC 0x60: 02 bc 02 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0x70: 00 00 00 00 00 12 30 40 24 27 2c 27 21 80 1f 80 EC 0x80: 00 00 00 06 *be 0d 03 00 00 00 0e 07 00 00 00 00 EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0xa0: ff 09 ff 09 ff ff 64 00 00 00 a2 41 ff ff e0 00 EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03 EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a Another set of values that varies often is the temperature readings. Since temperatures don't change vary fast, you can take several quick dumps to eliminate them. You can use a similar method to figure out the meaning of other embedded controller registers - e.g. make sure nothing else changes except the charging or discharging battery to determine which registers contain the current battery capacity, etc. If you experiment with this, do send me your results (including some complete dumps with a description of the conditions when they were taken.) LCD brightness control ---------------------- procfs: /proc/acpi/ibm/brightness sysfs backlight device "thinkpad_screen" This feature allows software control of the LCD brightness on ThinkPad models which don't have a hardware brightness slider. It has some limitations: the LCD backlight cannot be actually turned on or off by this interface, and in many ThinkPad models, the "dim while on battery" functionality will be enabled by the BIOS when this interface is used, and cannot be controlled. The backlight control has eight levels, ranging from 0 to 7. Some of the levels may not be distinct. Procfs notes: The available commands are: echo up >/proc/acpi/ibm/brightness echo down >/proc/acpi/ibm/brightness echo 'level <level>' >/proc/acpi/ibm/brightness Sysfs notes: The interface is implemented through the backlight sysfs class, which is poorly documented at this time. Locate the thinkpad_screen device under /sys/class/backlight, and inside it there will be the following attributes: max_brightness: Reads the maximum brightness the hardware can be set to. The minimum is always zero. actual_brightness: Reads what brightness the screen is set to at this instant. brightness: Writes request the driver to change brightness to the given value. Reads will tell you what brightness the driver is trying to set the display to when "power" is set to zero and the display has not been dimmed by a kernel power management event. power: power management mode, where 0 is "display on", and 1 to 3 will dim the display backlight to brightness level 0 because thinkpad-acpi cannot really turn the backlight off. Kernel power management events can temporarily increase the current power management level, i.e. they can dim the display. Volume control -- /proc/acpi/ibm/volume --------------------------------------- This feature allows volume control on ThinkPad models which don't have a hardware volume knob. The available commands are: echo up >/proc/acpi/ibm/volume echo down >/proc/acpi/ibm/volume echo mute >/proc/acpi/ibm/volume echo 'level <level>' >/proc/acpi/ibm/volume The <level> number range is 0 to 15 although not all of them may be distinct. The unmute the volume after the mute command, use either the up or down command (the level command will not unmute the volume). The current volume level and mute state is shown in the file. Fan control and monitoring: fan speed, fan enable/disable --------------------------------------------------------- procfs: /proc/acpi/ibm/fan sysfs device attributes: (hwmon) fan_input, pwm1, pwm1_enable NOTE NOTE NOTE: fan control operations are disabled by default for safety reasons. To enable them, the module parameter "fan_control=1" must be given to thinkpad-acpi. This feature attempts to show the current fan speed, control mode and other fan data that might be available. The speed is read directly from the hardware registers of the embedded controller. This is known to work on later R, T, X and Z series ThinkPads but may show a bogus value on other models. Fan levels: Most ThinkPad fans work in "levels" at the firmware interface. Level 0 stops the fan. The higher the level, the higher the fan speed, although adjacent levels often map to the same fan speed. 7 is the highest level, where the fan reaches the maximum recommended speed. Level "auto" means the EC changes the fan level according to some internal algorithm, usually based on readings from the thermal sensors. There is also a "full-speed" level, also known as "disengaged" level. In this level, the EC disables the speed-locked closed-loop fan control, and drives the fan as fast as it can go, which might exceed hardware limits, so use this level with caution. The fan usually ramps up or down slowly from one speed to another, and it is normal for the EC to take several seconds to react to fan commands. The full-speed level may take up to two minutes to ramp up to maximum speed, and in some ThinkPads, the tachometer readings go stale while the EC is transitioning to the full-speed level. WARNING WARNING WARNING: do not leave the fan disabled unless you are monitoring all of the temperature sensor readings and you are ready to enable it if necessary to avoid overheating. An enabled fan in level "auto" may stop spinning if the EC decides the ThinkPad is cool enough and doesn't need the extra airflow. This is normal, and the EC will spin the fan up if the varios thermal readings rise too much. On the X40, this seems to depend on the CPU and HDD temperatures. Specifically, the fan is turned on when either the CPU temperature climbs to 56 degrees or the HDD temperature climbs to 46 degrees. The fan is turned off when the CPU temperature drops to 49 degrees and the HDD temperature drops to 41 degrees. These thresholds cannot currently be controlled. The ThinkPad's ACPI DSDT code will reprogram the fan on its own when certain conditions are met. It will override any fan programming done through thinkpad-acpi. The thinkpad-acpi kernel driver can be programmed to revert the fan level to a safe setting if userspace does not issue one of the procfs fan commands: "enable", "disable", "level" or "watchdog", or if there are no writes to pwm1_enable (or to pwm1 *if and only if* pwm1_enable is set to 1, manual mode) within a configurable amount of time of up to 120 seconds. This functionality is called fan safety watchdog. Note that the watchdog timer stops after it enables the fan. It will be rearmed again automatically (using the same interval) when one of the above mentioned fan commands is received. The fan watchdog is, therefore, not suitable to protect against fan mode changes made through means other than the "enable", "disable", and "level" procfs fan commands, or the hwmon fan control sysfs interface. Procfs notes: The fan may be enabled or disabled with the following commands: echo enable >/proc/acpi/ibm/fan echo disable >/proc/acpi/ibm/fan Placing a fan on level 0 is the same as disabling it. Enabling a fan will try to place it in a safe level if it is too slow or disabled. The fan level can be controlled with the command: echo 'level <level>' > /proc/acpi/ibm/fan Where <level> is an integer from 0 to 7, or one of the words "auto" or "full-speed" (without the quotes). Not all ThinkPads support the "auto" and "full-speed" levels. The driver accepts "disengaged" as an alias for "full-speed", and reports it as "disengaged" for backwards compatibility. On the X31 and X40 (and ONLY on those models), the fan speed can be controlled to a certain degree. Once the fan is running, it can be forced to run faster or slower with the following command: echo 'speed <speed>' > /proc/acpi/ibm/fan The sustainable range of fan speeds on the X40 appears to be from about 3700 to about 7350. Values outside this range either do not have any effect or the fan speed eventually settles somewhere in that range. The fan cannot be stopped or started with this command. This functionality is incomplete, and not available through the sysfs interface. To program the safety watchdog, use the "watchdog" command. echo 'watchdog <interval in seconds>' > /proc/acpi/ibm/fan If you want to disable the watchdog, use 0 as the interval. Sysfs notes: The sysfs interface follows the hwmon subsystem guidelines for the most part, and the exception is the fan safety watchdog. Writes to any of the sysfs attributes may return the EINVAL error if that operation is not supported in a given ThinkPad or if the parameter is out-of-bounds, and EPERM if it is forbidden. They may also return EINTR (interrupted system call), and EIO (I/O error while trying to talk to the firmware). Features not yet implemented by the driver return ENOSYS. hwmon device attribute pwm1_enable: 0: PWM offline (fan is set to full-speed mode) 1: Manual PWM control (use pwm1 to set fan level) 2: Hardware PWM control (EC "auto" mode) 3: reserved (Software PWM control, not implemented yet) Modes 0 and 2 are not supported by all ThinkPads, and the driver is not always able to detect this. If it does know a mode is unsupported, it will return -EINVAL. hwmon device attribute pwm1: Fan level, scaled from the firmware values of 0-7 to the hwmon scale of 0-255. 0 means fan stopped, 255 means highest normal speed (level 7). This attribute only commands the fan if pmw1_enable is set to 1 (manual PWM control). hwmon device attribute fan1_input: Fan tachometer reading, in RPM. May go stale on certain ThinkPads while the EC transitions the PWM to offline mode, which can take up to two minutes. May return rubbish on older ThinkPads. driver attribute fan_watchdog: Fan safety watchdog timer interval, in seconds. Minimum is 1 second, maximum is 120 seconds. 0 disables the watchdog. To stop the fan: set pwm1 to zero, and pwm1_enable to 1. To start the fan in a safe mode: set pwm1_enable to 2. If that fails with EINVAL, try to set pwm1_enable to 1 and pwm1 to at least 128 (255 would be the safest choice, though). EXPERIMENTAL: WAN ----------------- procfs: /proc/acpi/ibm/wan sysfs device attribute: wwan_enable This feature is marked EXPERIMENTAL because the implementation directly accesses hardware registers and may not work as expected. USE WITH CAUTION! To use this feature, you need to supply the experimental=1 parameter when loading the module. This feature shows the presence and current state of a W-WAN (Sierra Wireless EV-DO) device. It was tested on a Lenovo Thinkpad X60. It should probably work on other Thinkpad models which come with this module installed. Procfs notes: If the W-WAN card is installed, the following commands can be used: echo enable > /proc/acpi/ibm/wan echo disable > /proc/acpi/ibm/wan Sysfs notes: If the W-WAN card is installed, it can be enabled / disabled through the "wwan_enable" thinkpad-acpi device attribute, and its current status can also be queried. enable: 0: disables WWAN card / WWAN card is disabled 1: enables WWAN card / WWAN card is enabled. Note: this interface will be probably be superseeded by the generic rfkill class, so it is NOT to be considered stable yet. Multiple Commands, Module Parameters ------------------------------------ Multiple commands can be written to the proc files in one shot by separating them with commas, for example: echo enable,0xffff > /proc/acpi/ibm/hotkey echo lcd_disable,crt_enable > /proc/acpi/ibm/video Commands can also be specified when loading the thinkpad-acpi module, for example: modprobe thinkpad_acpi hotkey=enable,0xffff video=auto_disable Enabling debugging output ------------------------- The module takes a debug paramater which can be used to selectively enable various classes of debugging output, for example: modprobe ibm_acpi debug=0xffff will enable all debugging output classes. It takes a bitmask, so to enable more than one output class, just add their values. Debug bitmask Description 0x0001 Initialization and probing 0x0002 Removal There is also a kernel build option to enable more debugging information, which may be necessary to debug driver problems. The level of debugging information output by the driver can be changed at runtime through sysfs, using the driver attribute debug_level. The attribute takes the same bitmask as the debug module parameter above. Force loading of module ----------------------- If thinkpad-acpi refuses to detect your ThinkPad, you can try to specify the module parameter force_load=1. Regardless of whether this works or not, please contact ibm-acpi-devel@lists.sourceforge.net with a report. Sysfs interface changelog: 0x000100: Initial sysfs support, as a single platform driver and device.