From cdcd9268a1b03c6695ea07983ce029b2b4a099d8 Mon Sep 17 00:00:00 2001 From: Jonathan Woithe Date: Tue, 28 Feb 2006 11:36:42 +0100 Subject: [ALSA] HDA/ALC260: 2/7 - switch pin buffer enables Modules: HDA Codec driver This patch adds functionality which switches the input/output buffer enables of retasking pins when the user changes their mode with the mode control. This probably reduces noise *slightly* for recording compared to the case where both input and output buffers were enabled simultaneously. Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 58 ++++++++++++++++++++++++++++--------------- 1 file changed, 38 insertions(+), 20 deletions(-) (limited to 'sound/pci/hda') diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index b34d2448d172..600d0a037842 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -306,9 +306,32 @@ static int alc_pin_mode_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_v val = alc_pin_mode_min(dir); change = pinctl != alc_pin_mode_values[val]; - if (change) + if (change) { + /* Set pin mode to that requested */ snd_hda_codec_write(codec,nid,0,AC_VERB_SET_PIN_WIDGET_CONTROL, alc_pin_mode_values[val]); + + /* Also enable the retasking pin's input/output as required + * for the requested pin mode. Enum values of 2 or less are + * input modes. + * + * Dynamically switching the input/output buffers probably + * reduces noise slightly, particularly on input. However, + * havingboth input and output buffers enabled + * simultaneously doesn't seem to be problematic. + */ + if (val <= 2) { + snd_hda_codec_write(codec,nid,0,AC_VERB_SET_AMP_GAIN_MUTE, + AMP_OUT_MUTE); + snd_hda_codec_write(codec,nid,0,AC_VERB_SET_AMP_GAIN_MUTE, + AMP_IN_UNMUTE(0)); + } else { + snd_hda_codec_write(codec,nid,0,AC_VERB_SET_AMP_GAIN_MUTE, + AMP_IN_MUTE(0)); + snd_hda_codec_write(codec,nid,0,AC_VERB_SET_AMP_GAIN_MUTE, + AMP_OUT_UNMUTE); + } + } return change; } @@ -2744,14 +2767,16 @@ static struct hda_verb alc260_fujitsu_init_verbs[] = { /* Unmute HP pin widget amp left and right (no equiv mixer ctrl) */ {0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, - /* Unmute Line1 pin widget amp left and right (no equiv mixer ctrl) */ + /* Unmute Line1 pin widget output buffer since it starts as an output. + * If the pin mode is changed by the user the pin mode control will + * take care of enabling the pin's input/output buffers as needed. + * Therefore there's no need to enable the input buffer at this + * stage. + */ {0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, - /* Unmute Line1 pin widget input for when this pin is used as input - * (no equiv mixer ctrl). Having input and output unmuted doesn't - * seem to cause a problem. - */ - {0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, - /* Unmute pin widget used for Line-in (no equiv mixer ctrl) */ + /* Unmute input buffer of pin widget used for Line-in (no equiv + * mixer ctrl) + */ {0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, /* Mute capture amp left and right */ @@ -2882,7 +2907,11 @@ static struct hda_verb alc260_test_init_verbs[] = { {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO}, - /* Unmute retasking pin widget output amp left/right (no mixer ctrl) */ + /* Unmute retasking pin widget output buffers since the default + * state appears to be output. As the pin mode is changed by the + * user the pin mode control will take care of enabling the pin's + * input/output buffers as needed. + */ {0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, {0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, {0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, @@ -2892,17 +2921,6 @@ static struct hda_verb alc260_test_init_verbs[] = { /* Also unmute the mono-out pin widget */ {0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, - /* Also unmute the retasking pin input amps. Having the input and - * output amps unmuted at the same time doesn't appear to cause any - * trouble. - */ - {0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, - {0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, - {0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, - {0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, - {0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, - {0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, - /* Mute capture amp left and right */ {0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, /* Set ADC connection select to match default mixer setting - line -- cgit v1.2.2