From bcd2360c1ff9fff69eb45bedc5fba7240c6da875 Mon Sep 17 00:00:00 2001
From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Date: Tue, 30 Oct 2012 05:12:23 +0800
Subject: arm: at91: move platfarm_data to include/linux/platform_data/atmel.h

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 include/linux/platform_data/atmel.h | 67 +++++++++++++++++++++++++++++++++++++
 1 file changed, 67 insertions(+)

(limited to 'include/linux/platform_data/atmel.h')

diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
index b0f2c56a8ea2..dbd6d53cc270 100644
--- a/include/linux/platform_data/atmel.h
+++ b/include/linux/platform_data/atmel.h
@@ -8,6 +8,49 @@
 #define __ATMEL_H__
 
 #include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/usb/atmel_usba_udc.h>
+#include <linux/atmel-mci.h>
+#include <sound/atmel-ac97c.h>
+#include <linux/serial.h>
+#include <linux/platform_data/macb.h>
+
+ /* USB Device */
+struct at91_udc_data {
+	int	vbus_pin;		/* high == host powering us */
+	u8	vbus_active_low;	/* vbus polarity */
+	u8	vbus_polled;		/* Use polling, not interrupt */
+	int	pullup_pin;		/* active == D+ pulled up */
+	u8	pullup_active_low;	/* true == pullup_pin is active low */
+};
+
+ /* Compact Flash */
+struct at91_cf_data {
+	int	irq_pin;		/* I/O IRQ */
+	int	det_pin;		/* Card detect */
+	int	vcc_pin;		/* power switching */
+	int	rst_pin;		/* card reset */
+	u8	chipselect;		/* EBI Chip Select number */
+	u8	flags;
+#define AT91_CF_TRUE_IDE	0x01
+#define AT91_IDE_SWAP_A0_A2	0x02
+};
+
+ /* USB Host */
+#define AT91_MAX_USBH_PORTS	3
+struct at91_usbh_data {
+	int		vbus_pin[AT91_MAX_USBH_PORTS];	/* port power-control pin */
+	int             overcurrent_pin[AT91_MAX_USBH_PORTS];
+	u8		ports;				/* number of ports on root hub */
+	u8              overcurrent_supported;
+	u8              vbus_pin_active_low[AT91_MAX_USBH_PORTS];
+	u8              overcurrent_status[AT91_MAX_USBH_PORTS];
+	u8              overcurrent_changed[AT91_MAX_USBH_PORTS];
+};
 
  /* NAND / SmartMedia */
 struct atmel_nand_data {
@@ -24,4 +67,28 @@ struct atmel_nand_data {
 	unsigned int	num_parts;
 };
 
+ /* Serial */
+struct atmel_uart_data {
+	int			num;		/* port num */
+	short			use_dma_tx;	/* use transmit DMA? */
+	short			use_dma_rx;	/* use receive DMA? */
+	void __iomem		*regs;		/* virt. base address, if any */
+	struct serial_rs485	rs485;		/* rs485 settings */
+};
+
+ /* Touchscreen Controller */
+struct at91_tsadcc_data {
+	unsigned int    adc_clock;
+	u8		pendet_debounce;
+	u8		ts_sample_hold_time;
+};
+
+/* CAN */
+struct at91_can_data {
+	void (*transceiver_switch)(int on);
+};
+
+/* FIXME: this needs a better location, but gets stuff building again */
+extern int at91_suspend_entering_slow_clock(void);
+
 #endif /* __ATMEL_H__ */
-- 
cgit v1.2.2