From 8c83f80b2d335176f72d8729fe1dfe19c5812cb1 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Tue, 9 Dec 2008 00:10:11 -0800 Subject: sungem: Make PCS PHY support partially work again. As reported by Hermann Lauer, PCS PHY support in the sungem driver simply doesn't work. When the chip is reset due to open, or some other similar operation, the PCS is reset too but we don't program it back into a running state. The result is no link when the device is brought up. This partially rectifies the situation for the moment, by kicking the PCS after a sungem chip reset so that it will renegotiate and be re-enabled again. The behavior is still a little bit dodgy as the added renegotiate make the link take some time after bringing the interface up, but this is a significant improvement in that things actually work now :-) Based almost entirely upon an initial patch by Hermann. Signed-off-by: David S. Miller --- drivers/net/sungem.c | 129 +++++++++++++++++++++++++++++---------------------- 1 file changed, 73 insertions(+), 56 deletions(-) (limited to 'drivers') diff --git a/drivers/net/sungem.c b/drivers/net/sungem.c index 1349e419673c..bb7a47829f7f 100644 --- a/drivers/net/sungem.c +++ b/drivers/net/sungem.c @@ -1142,6 +1142,70 @@ static int gem_start_xmit(struct sk_buff *skb, struct net_device *dev) return NETDEV_TX_OK; } +static void gem_pcs_reset(struct gem *gp) +{ + int limit; + u32 val; + + /* Reset PCS unit. */ + val = readl(gp->regs + PCS_MIICTRL); + val |= PCS_MIICTRL_RST; + writel(val, gp->regs + PCS_MIICTRL); + + limit = 32; + while (readl(gp->regs + PCS_MIICTRL) & PCS_MIICTRL_RST) { + udelay(100); + if (limit-- <= 0) + break; + } + if (limit <= 0) + printk(KERN_WARNING "%s: PCS reset bit would not clear.\n", + gp->dev->name); +} + +static void gem_pcs_reinit_adv(struct gem *gp) +{ + u32 val; + + /* Make sure PCS is disabled while changing advertisement + * configuration. + */ + val = readl(gp->regs + PCS_CFG); + val &= ~(PCS_CFG_ENABLE | PCS_CFG_TO); + writel(val, gp->regs + PCS_CFG); + + /* Advertise all capabilities except assymetric + * pause. + */ + val = readl(gp->regs + PCS_MIIADV); + val |= (PCS_MIIADV_FD | PCS_MIIADV_HD | + PCS_MIIADV_SP | PCS_MIIADV_AP); + writel(val, gp->regs + PCS_MIIADV); + + /* Enable and restart auto-negotiation, disable wrapback/loopback, + * and re-enable PCS. + */ + val = readl(gp->regs + PCS_MIICTRL); + val |= (PCS_MIICTRL_RAN | PCS_MIICTRL_ANE); + val &= ~PCS_MIICTRL_WB; + writel(val, gp->regs + PCS_MIICTRL); + + val = readl(gp->regs + PCS_CFG); + val |= PCS_CFG_ENABLE; + writel(val, gp->regs + PCS_CFG); + + /* Make sure serialink loopback is off. The meaning + * of this bit is logically inverted based upon whether + * you are in Serialink or SERDES mode. + */ + val = readl(gp->regs + PCS_SCTRL); + if (gp->phy_type == phy_serialink) + val &= ~PCS_SCTRL_LOOP; + else + val |= PCS_SCTRL_LOOP; + writel(val, gp->regs + PCS_SCTRL); +} + #define STOP_TRIES 32 /* Must be invoked under gp->lock and gp->tx_lock. */ @@ -1168,6 +1232,9 @@ static void gem_reset(struct gem *gp) if (limit <= 0) printk(KERN_ERR "%s: SW reset is ghetto.\n", gp->dev->name); + + if (gp->phy_type == phy_serialink || gp->phy_type == phy_serdes) + gem_pcs_reinit_adv(gp); } /* Must be invoked under gp->lock and gp->tx_lock. */ @@ -1324,7 +1391,7 @@ static int gem_set_link_modes(struct gem *gp) gp->phy_type == phy_serdes) { u32 pcs_lpa = readl(gp->regs + PCS_MIILP); - if (pcs_lpa & PCS_MIIADV_FD) + if ((pcs_lpa & PCS_MIIADV_FD) || gp->phy_type == phy_serdes) full_duplex = 1; speed = SPEED_1000; } @@ -1488,6 +1555,9 @@ static void gem_link_timer(unsigned long data) val = readl(gp->regs + PCS_MIISTAT); if ((val & PCS_MIISTAT_LS) != 0) { + if (gp->lstate == link_up) + goto restart; + gp->lstate = link_up; netif_carrier_on(gp->dev); (void)gem_set_link_modes(gp); @@ -1708,61 +1778,8 @@ static void gem_init_phy(struct gem *gp) if (gp->phy_mii.def && gp->phy_mii.def->ops->init) gp->phy_mii.def->ops->init(&gp->phy_mii); } else { - u32 val; - int limit; - - /* Reset PCS unit. */ - val = readl(gp->regs + PCS_MIICTRL); - val |= PCS_MIICTRL_RST; - writel(val, gp->regs + PCS_MIICTRL); - - limit = 32; - while (readl(gp->regs + PCS_MIICTRL) & PCS_MIICTRL_RST) { - udelay(100); - if (limit-- <= 0) - break; - } - if (limit <= 0) - printk(KERN_WARNING "%s: PCS reset bit would not clear.\n", - gp->dev->name); - - /* Make sure PCS is disabled while changing advertisement - * configuration. - */ - val = readl(gp->regs + PCS_CFG); - val &= ~(PCS_CFG_ENABLE | PCS_CFG_TO); - writel(val, gp->regs + PCS_CFG); - - /* Advertise all capabilities except assymetric - * pause. - */ - val = readl(gp->regs + PCS_MIIADV); - val |= (PCS_MIIADV_FD | PCS_MIIADV_HD | - PCS_MIIADV_SP | PCS_MIIADV_AP); - writel(val, gp->regs + PCS_MIIADV); - - /* Enable and restart auto-negotiation, disable wrapback/loopback, - * and re-enable PCS. - */ - val = readl(gp->regs + PCS_MIICTRL); - val |= (PCS_MIICTRL_RAN | PCS_MIICTRL_ANE); - val &= ~PCS_MIICTRL_WB; - writel(val, gp->regs + PCS_MIICTRL); - - val = readl(gp->regs + PCS_CFG); - val |= PCS_CFG_ENABLE; - writel(val, gp->regs + PCS_CFG); - - /* Make sure serialink loopback is off. The meaning - * of this bit is logically inverted based upon whether - * you are in Serialink or SERDES mode. - */ - val = readl(gp->regs + PCS_SCTRL); - if (gp->phy_type == phy_serialink) - val &= ~PCS_SCTRL_LOOP; - else - val |= PCS_SCTRL_LOOP; - writel(val, gp->regs + PCS_SCTRL); + gem_pcs_reset(gp); + gem_pcs_reinit_adv(gp); } /* Default aneg parameters */ -- cgit v1.2.2 From fbf0229e946deb9e6c711f9eaa5c8d670c3a28fd Mon Sep 17 00:00:00 2001 From: Hermann Lauer Date: Tue, 9 Dec 2008 15:39:14 -0800 Subject: sungem: improve ethtool output with internal pcs and serdes From: Hermann Lauer Attached is a patch which improves the output of ethtool (see below) to some sensefull values with a sungem fibre card which uses the sungem interal pcs connected to a serdes chip. The seriallink case in the driver is untouched. Most values are hardcoded, because gigabit fibre autoneg is anyways limited and the driver don't really support much at the moment with that hardware. Signed-off-by: David S. Miller --- drivers/net/sungem.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+) (limited to 'drivers') diff --git a/drivers/net/sungem.c b/drivers/net/sungem.c index bb7a47829f7f..fed7eba65ead 100644 --- a/drivers/net/sungem.c +++ b/drivers/net/sungem.c @@ -2697,6 +2697,21 @@ static int gem_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) cmd->speed = 0; cmd->duplex = cmd->port = cmd->phy_address = cmd->transceiver = cmd->autoneg = 0; + + /* serdes means usually a Fibre connector, with most fixed */ + if (gp->phy_type == phy_serdes) { + cmd->port = PORT_FIBRE; + cmd->supported = (SUPPORTED_1000baseT_Half | + SUPPORTED_1000baseT_Full | + SUPPORTED_FIBRE | SUPPORTED_Autoneg | + SUPPORTED_Pause | SUPPORTED_Asym_Pause); + cmd->advertising = cmd->supported; + cmd->transceiver = XCVR_INTERNAL; + if (gp->lstate == link_up) + cmd->speed = SPEED_1000; + cmd->duplex = DUPLEX_FULL; + cmd->autoneg = 1; + } } cmd->maxtxpkt = cmd->maxrxpkt = 0; -- cgit v1.2.2 From 30bb0e0dce78427f3e5cb728d6b5ea73acbefffa Mon Sep 17 00:00:00 2001 From: Jeff Kirsher Date: Thu, 11 Dec 2008 21:28:11 -0800 Subject: e1000e: fix double release of mutex During a reset, releasing the swflag after it failed to be acquired would cause a double unlock of the mutex. Instead, test whether acquisition of the swflag was successful and if not, do not release the swflag. The reset must still be done to bring the device to a quiescent state. This resolves [BUG 12200] BUG: bad unlock balance detected! e1000e http://bugzilla.kernel.org/show_bug.cgi?id=12200 Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/ich8lan.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index 523b9716a543..d115a6d30f29 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -1893,12 +1893,17 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ctrl |= E1000_CTRL_PHY_RST; } ret_val = e1000_acquire_swflag_ich8lan(hw); + /* Whether or not the swflag was acquired, we need to reset the part */ hw_dbg(hw, "Issuing a global reset to ich8lan"); ew32(CTRL, (ctrl | E1000_CTRL_RST)); msleep(20); - /* release the swflag because it is not reset by hardware reset */ - e1000_release_swflag_ich8lan(hw); + if (!ret_val) { + /* release the swflag because it is not reset by + * hardware reset + */ + e1000_release_swflag_ich8lan(hw); + } ret_val = e1000e_get_auto_rd_done(hw); if (ret_val) { -- cgit v1.2.2 From 25a41b280083259d05d68f61633194344a1f8a9f Mon Sep 17 00:00:00 2001 From: Stefan Richter Date: Sat, 13 Dec 2008 01:43:59 +0100 Subject: ieee1394: add quirk fix for Freecom HDD According to http://bugzilla.kernel.org/show_bug.cgi?id=12206, Freecom FireWire Hard Drive 1TB reports max_rom=2 but returns garbage if block read requests are used to read the config ROM. Force max_rom=0 to limit them to quadlet read requests. Reported-by: Christian Mueller Signed-off-by: Stefan Richter --- drivers/ieee1394/nodemgr.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers') diff --git a/drivers/ieee1394/nodemgr.c b/drivers/ieee1394/nodemgr.c index d333ae22459c..79ef5fd928ae 100644 --- a/drivers/ieee1394/nodemgr.c +++ b/drivers/ieee1394/nodemgr.c @@ -115,8 +115,14 @@ static int nodemgr_bus_read(struct csr1212_csr *csr, u64 addr, u16 length, return error; } +#define OUI_FREECOM_TECHNOLOGIES_GMBH 0x0001db + static int nodemgr_get_max_rom(quadlet_t *bus_info_data, void *__ci) { + /* Freecom FireWire Hard Drive firmware bug */ + if (be32_to_cpu(bus_info_data[3]) >> 8 == OUI_FREECOM_TECHNOLOGIES_GMBH) + return 0; + return (be32_to_cpu(bus_info_data[2]) >> 8) & 0x3; } -- cgit v1.2.2 From 35024c384ba4faaeac361a1ffee05a1475f9a9ed Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Mon, 15 Dec 2008 13:54:14 -0800 Subject: pcmcia: blackfin: fix bug - add missing ; to MODULE macro Cc: Michael Hennerich Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu Cc: Dominik Brodowski Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/pcmcia/bfin_cf_pcmcia.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/pcmcia/bfin_cf_pcmcia.c b/drivers/pcmcia/bfin_cf_pcmcia.c index bb7338863fb9..b59d4115d20f 100644 --- a/drivers/pcmcia/bfin_cf_pcmcia.c +++ b/drivers/pcmcia/bfin_cf_pcmcia.c @@ -334,6 +334,6 @@ static void __exit bfin_cf_exit(void) module_init(bfin_cf_init); module_exit(bfin_cf_exit); -MODULE_AUTHOR("Michael Hennerich ") +MODULE_AUTHOR("Michael Hennerich "); MODULE_DESCRIPTION("BFIN CF/PCMCIA Driver"); MODULE_LICENSE("GPL"); -- cgit v1.2.2 From 38aefbc585c5d86df101e7644bff2c47112783d4 Mon Sep 17 00:00:00 2001 From: Frederik Deweerdt Date: Mon, 15 Dec 2008 13:54:19 -0800 Subject: ACPI toshiba: only register rfkill if bt is enabled Part of the rfkill initialization was done whenever BT was on or not. The following patch checks for BT presence before registering the rfkill to the input layer. Some minor cleanups (> 80 char lines) were also added in the process. On Tue, Oct 28, 2008 at 10:10:37PM +0300, Andrey Borzenkov wrote: [...] > [ 66.633036] toshiba_acpi: Toshiba Laptop ACPI Extras version 0.19 > [ 66.633054] toshiba_acpi: HCI method: \_SB_.VALD.GHCI > [ 66.637764] input: Toshiba RFKill Switch as /devices/virtual/input/input3 [...] > [ 113.920753] ------------[ cut here ]------------ > [ 113.920828] kernel BUG at /home/bor/src/linux-git/net/rfkill/rfkill.c:347! > [ 113.920845] invalid opcode: 0000 [#1] > [ 113.920877] last sysfs file: /sys/devices/pci0000:00/0000:00:04.0/host0/target0:0:0/0:0:0:0/block/sda/size > [ 113.920900] Dumping ftrace buffer: > [ 113.920919] (ftrace buffer empty) > [ 113.920933] Modules linked in: af_packet irnet ppp_generic slhc ircomm_tty ircomm binfmt_misc loop dm_mirror dm_region_hash dm_log dm_round_robin dm_multipath dm_mod alim15x3 ide_core nvram toshiba cryptomgr aead crypto_blkcipher michael_mic crypto_algapi orinoco_cs orinoco hermes_dld hermes pcmcia firmware_class snd_ali5451 snd_ac97_codec ac97_bus snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device smsc_ircc2 snd_pcm_oss snd_pcm rtc_cmos irda snd_timer snd_mixer_oss rtc_core snd crc_ccitt yenta_socket rtc_lib rsrc_nonstatic i2c_ali1535 pcmcia_core pcspkr psmouse soundcore i2c_core evdev sr_mod snd_page_alloc alim1535_wdt cdrom fan sg video output toshiba_acpi rfkill thermal backlight ali_agp processor ac button input_polldev battery agpgart ohci_hcd usbcore reiserfs pata_ali libata sd_mod scsi_mod [last unloaded: scsi_wait_scan] > [ 113.921765] > [ 113.921785] Pid: 3272, comm: ipolldevd Not tainted (2.6.28-rc2-1avb #3) PORTEGE 4000 > [ 113.921801] EIP: 0060:[] EFLAGS: 00010246 CPU: 0 > [ 113.921854] EIP is at rfkill_force_state+0x53/0x90 [rfkill] > [ 113.921870] EAX: 00000000 EBX: 00000000 ECX: 00000003 EDX: 00000000 > [ 113.921885] ESI: 00000000 EDI: ddd50300 EBP: d8d7af40 ESP: d8d7af24 > [ 113.921900] DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068 > [ 113.921918] Process ipolldevd (pid: 3272, ti=d8d7a000 task=d8d93c90 task.ti=d8d7a000) > [ 113.921933] Stack: > [ 113.921945] d8d7af38 00000246 dfb029d8 dfb029c0 dfb029d8 dfb029c0 ddd50300 d8d7af5c > [ 113.922014] dfb018e2 01000246 01000000 ddd50300 ddd50314 ddabb8a0 d8d7af68 dfb381c1 > [ 113.922098] 00000000 d8d7afa4 c012ec0a 00000000 00000002 00000000 c012eba8 ddabb8c0 > [ 113.922240] Call Trace: > [ 113.922240] [] ? bt_poll_rfkill+0x5c/0x82 [toshiba_acpi] > [ 113.922240] [] ? input_polled_device_work+0x11/0x40 [input_polldev] > [ 113.922240] [] ? run_workqueue+0xea/0x1f0 > [ 113.922240] [] ? run_workqueue+0x88/0x1f0 > [ 113.922240] [] ? input_polled_device_work+0x0/0x40 [input_polldev] > [ 113.922240] [] ? worker_thread+0x87/0xf0 > [ 113.922240] [] ? autoremove_wake_function+0x0/0x50 > [ 113.922240] [] ? worker_thread+0x0/0xf0 > [ 113.922240] [] ? kthread+0x3f/0x80 > [ 113.922240] [] ? kthread+0x0/0x80 > [ 113.922240] [] ? kernel_thread_helper+0x7/0x10 > [ 113.922240] Code: 43 54 89 73 54 39 c6 74 11 89 d9 ba 01 00 00 00 b8 40 68 aa df e8 3e 35 69 e0 89 f8 e8 77 fd 85 e0 31 c0 83 c4 10 5b 5e 5f 5d c3 <0f> 0b eb fe 89 f6 8d bc 27 00 00 00 00 be f4 4d aa df bb 5f 01 > [ 113.922240] EIP: [] rfkill_force_state+0x53/0x90 [rfkill] SS:ESP 0068:d8d7af24 > [ 113.924700] ---[ end trace 0e404eb40cadd5f0 ]--- Signed-off-by: Frederik Deweerdt Tested-by: Andrey Borzenkov Acked-by: Len Brown Cc: Richard Purdie Acked-by: Philip Langdale Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/acpi/toshiba_acpi.c | 54 ++++++++++++++++++++++++--------------------- 1 file changed, 29 insertions(+), 25 deletions(-) (limited to 'drivers') diff --git a/drivers/acpi/toshiba_acpi.c b/drivers/acpi/toshiba_acpi.c index 25f531d892de..40e60fc2e596 100644 --- a/drivers/acpi/toshiba_acpi.c +++ b/drivers/acpi/toshiba_acpi.c @@ -824,32 +824,36 @@ static int __init toshiba_acpi_init(void) toshiba_acpi_exit(); return -ENOMEM; } - } - /* Register input device for kill switch */ - toshiba_acpi.poll_dev = input_allocate_polled_device(); - if (!toshiba_acpi.poll_dev) { - printk(MY_ERR "unable to allocate kill-switch input device\n"); - toshiba_acpi_exit(); - return -ENOMEM; - } - toshiba_acpi.poll_dev->private = &toshiba_acpi; - toshiba_acpi.poll_dev->poll = bt_poll_rfkill; - toshiba_acpi.poll_dev->poll_interval = 1000; /* msecs */ - - toshiba_acpi.poll_dev->input->name = toshiba_acpi.rfk_name; - toshiba_acpi.poll_dev->input->id.bustype = BUS_HOST; - toshiba_acpi.poll_dev->input->id.vendor = 0x0930; /* Toshiba USB ID */ - set_bit(EV_SW, toshiba_acpi.poll_dev->input->evbit); - set_bit(SW_RFKILL_ALL, toshiba_acpi.poll_dev->input->swbit); - input_report_switch(toshiba_acpi.poll_dev->input, SW_RFKILL_ALL, TRUE); - input_sync(toshiba_acpi.poll_dev->input); - - ret = input_register_polled_device(toshiba_acpi.poll_dev); - if (ret) { - printk(MY_ERR "unable to register kill-switch input device\n"); - toshiba_acpi_exit(); - return ret; + /* Register input device for kill switch */ + toshiba_acpi.poll_dev = input_allocate_polled_device(); + if (!toshiba_acpi.poll_dev) { + printk(MY_ERR + "unable to allocate kill-switch input device\n"); + toshiba_acpi_exit(); + return -ENOMEM; + } + toshiba_acpi.poll_dev->private = &toshiba_acpi; + toshiba_acpi.poll_dev->poll = bt_poll_rfkill; + toshiba_acpi.poll_dev->poll_interval = 1000; /* msecs */ + + toshiba_acpi.poll_dev->input->name = toshiba_acpi.rfk_name; + toshiba_acpi.poll_dev->input->id.bustype = BUS_HOST; + /* Toshiba USB ID */ + toshiba_acpi.poll_dev->input->id.vendor = 0x0930; + set_bit(EV_SW, toshiba_acpi.poll_dev->input->evbit); + set_bit(SW_RFKILL_ALL, toshiba_acpi.poll_dev->input->swbit); + input_report_switch(toshiba_acpi.poll_dev->input, + SW_RFKILL_ALL, TRUE); + input_sync(toshiba_acpi.poll_dev->input); + + ret = input_register_polled_device(toshiba_acpi.poll_dev); + if (ret) { + printk(MY_ERR + "unable to register kill-switch input device\n"); + toshiba_acpi_exit(); + return ret; + } } return 0; -- cgit v1.2.2 From 93d546399c2b7d66a54d5fbd5eee17de19246bf6 Mon Sep 17 00:00:00 2001 From: Matt Fleming Date: Tue, 16 Dec 2008 09:15:31 +0900 Subject: sh: maple: Do not pass SLAB_POISON to kmem_cache_create() SLAB_POISON is not a valid flag for kmem_create_cache() unless CONFIG_DEBUG_SLAB is set, so remove it from the flags argument. Acked-by: Adrian McMenamin Signed-off-by: Matt Fleming Signed-off-by: Paul Mundt --- drivers/sh/maple/maple.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/sh/maple/maple.c b/drivers/sh/maple/maple.c index d1812d32f47d..63f0de29aa14 100644 --- a/drivers/sh/maple/maple.c +++ b/drivers/sh/maple/maple.c @@ -827,7 +827,7 @@ static int __init maple_bus_init(void) maple_queue_cache = kmem_cache_create("maple_queue_cache", 0x400, 0, - SLAB_POISON|SLAB_HWCACHE_ALIGN, NULL); + SLAB_HWCACHE_ALIGN, NULL); if (!maple_queue_cache) goto cleanup_bothirqs; -- cgit v1.2.2 From d10d491f842243e2e3bf5a2714020f9d649e1e38 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Thu, 11 Dec 2008 13:42:42 +0900 Subject: libata: fix Seagate NCQ+FLUSH blacklist Due to miscommunication, P/N was mistaken as firmware revision strings. Update it. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 65 ++++++++++++++++++++++++++++++++++++++++++----- 1 file changed, 59 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 5e2eb740df46..bc6695e3c848 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -4050,17 +4050,70 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { { "ST3160023AS", "3.42", ATA_HORKAGE_NONCQ }, /* Seagate NCQ + FLUSH CACHE firmware bug */ - { "ST31500341AS", "9JU138", ATA_HORKAGE_NONCQ | + { "ST31500341AS", "SD15", ATA_HORKAGE_NONCQ | ATA_HORKAGE_FIRMWARE_WARN }, - { "ST31000333AS", "9FZ136", ATA_HORKAGE_NONCQ | + { "ST31500341AS", "SD16", ATA_HORKAGE_NONCQ | ATA_HORKAGE_FIRMWARE_WARN }, - { "ST3640623AS", "9FZ164", ATA_HORKAGE_NONCQ | + { "ST31500341AS", "SD17", ATA_HORKAGE_NONCQ | ATA_HORKAGE_FIRMWARE_WARN }, - { "ST3640323AS", "9FZ134", ATA_HORKAGE_NONCQ | + { "ST31500341AS", "SD18", ATA_HORKAGE_NONCQ | ATA_HORKAGE_FIRMWARE_WARN }, - { "ST3320813AS", "9FZ182", ATA_HORKAGE_NONCQ | + { "ST31500341AS", "SD19", ATA_HORKAGE_NONCQ | ATA_HORKAGE_FIRMWARE_WARN }, - { "ST3320613AS", "9FZ162", ATA_HORKAGE_NONCQ | + + { "ST31000333AS", "SD15", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST31000333AS", "SD16", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST31000333AS", "SD17", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST31000333AS", "SD18", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST31000333AS", "SD19", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + + { "ST3640623AS", "SD15", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3640623AS", "SD16", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3640623AS", "SD17", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3640623AS", "SD18", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3640623AS", "SD19", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + + { "ST3640323AS", "SD15", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3640323AS", "SD16", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3640323AS", "SD17", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3640323AS", "SD18", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3640323AS", "SD19", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + + { "ST3320813AS", "SD15", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3320813AS", "SD16", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3320813AS", "SD17", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3320813AS", "SD18", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3320813AS", "SD19", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + + { "ST3320613AS", "SD15", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3320613AS", "SD16", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3320613AS", "SD17", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3320613AS", "SD18", ATA_HORKAGE_NONCQ | + ATA_HORKAGE_FIRMWARE_WARN }, + { "ST3320613AS", "SD19", ATA_HORKAGE_NONCQ | ATA_HORKAGE_FIRMWARE_WARN }, /* Blacklist entries taken from Silicon Image 3124/3132 -- cgit v1.2.2 From bab5b32a537edc83ff86bff91e46f328339f49f8 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Tue, 9 Dec 2008 17:13:19 +0900 Subject: pata_hpt366: fix cable detection, pata_hpt366 is strange in that its two channels occupy two PCI functions and both are primary channels and bit1 of PCI configuration register 0x5A indicates cable for both channels. Signed-off-by: Tejun Heo Cc: Alan Cox Cc: Sergei Shtylyov Signed-off-by: Jeff Garzik --- drivers/ata/pata_hpt366.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c index a098ba8eaab6..4824821745a2 100644 --- a/drivers/ata/pata_hpt366.c +++ b/drivers/ata/pata_hpt366.c @@ -211,11 +211,15 @@ static u32 hpt36x_find_mode(struct ata_port *ap, int speed) static int hpt36x_cable_detect(struct ata_port *ap) { - u8 ata66; struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 ata66; + /* + * Each channel of pata_hpt366 occupies separate PCI function + * as the primary channel and bit1 indicates the cable type. + */ pci_read_config_byte(pdev, 0x5A, &ata66); - if (ata66 & (1 << ap->port_no)) + if (ata66 & 2) return ATA_CBL_PATA40; return ATA_CBL_PATA80; } -- cgit v1.2.2 From 3ee89f177e3cef0b5b024bcb6df683a3fa7d795f Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Tue, 9 Dec 2008 17:14:04 +0900 Subject: pata_hpt366: no ATAPI DMA IDE hpt366 driver doesn't allow DMA for ATAPI devices and MWDMA2 on ATAPI device locks up pata_hpt366. Follow the suit. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/pata_hpt366.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c index 4824821745a2..e0c4f05d7d57 100644 --- a/drivers/ata/pata_hpt366.c +++ b/drivers/ata/pata_hpt366.c @@ -183,7 +183,9 @@ static unsigned long hpt366_filter(struct ata_device *adev, unsigned long mask) mask &= ~(0xF8 << ATA_SHIFT_UDMA); if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4)) mask &= ~(0xF0 << ATA_SHIFT_UDMA); - } + } else if (adev->class == ATA_DEV_ATAPI) + mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA); + return ata_bmdma_mode_filter(adev, mask); } -- cgit v1.2.2 From a804644a1a31a0b85e4c7d3c49f30419513cb6c1 Mon Sep 17 00:00:00 2001 From: Mike Ditto Date: Tue, 16 Dec 2008 20:17:09 +0000 Subject: i2c-cpm: Detect and report NAK right away instead of timing out Make the driver report an ENXIO error immediately upon NAK instead of waiting for another interrupt and getting a timeout. When reading from a device that is not present or declines to respond to, e.g., a non-existent register address, CPM immediately reports a NAK condition in the TxBD, but the driver kept waiting until a timeout, which takes 1 second and causes an ugly console error message. Signed-off-by: Mike Ditto Acked-by: Jochen Friedrich [ben-linux@fluff.org: reordered description text] Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-cpm.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-cpm.c b/drivers/i2c/busses/i2c-cpm.c index 228f75723063..3fcf78e906db 100644 --- a/drivers/i2c/busses/i2c-cpm.c +++ b/drivers/i2c/busses/i2c-cpm.c @@ -365,6 +365,7 @@ static int cpm_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) pmsg = &msgs[tptr]; if (pmsg->flags & I2C_M_RD) ret = wait_event_interruptible_timeout(cpm->i2c_wait, + (in_be16(&tbdf[tptr].cbd_sc) & BD_SC_NAK) || !(in_be16(&rbdf[rptr].cbd_sc) & BD_SC_EMPTY), 1 * HZ); else -- cgit v1.2.2 From be44f01e8af3862767f466f89c12640a2f2b0038 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 31 Oct 2008 16:10:22 +0000 Subject: i2c-s3c2410: fix check for being in suspend. As noted by Julia Lawall , we can never trigger the check for being in suspend due to the result of !readl(i2c->regs + S3C2410_IICCON) & S3C2410_IICCON_IRQEN always being 0. Add suspend/resume hooks to stop i2c transactions happening until the driver has been resumed. Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-s3c2410.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index 1fac4e233133..b7434d24904e 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -56,6 +56,7 @@ enum s3c24xx_i2c_state { struct s3c24xx_i2c { spinlock_t lock; wait_queue_head_t wait; + unsigned int suspended:1; struct i2c_msg *msg; unsigned int msg_num; @@ -507,7 +508,7 @@ static int s3c24xx_i2c_doxfer(struct s3c24xx_i2c *i2c, struct i2c_msg *msgs, int unsigned long timeout; int ret; - if (!(readl(i2c->regs + S3C2410_IICCON) & S3C2410_IICCON_IRQEN)) + if (i2c->suspended) return -EIO; ret = s3c24xx_i2c_set_master(i2c); @@ -986,17 +987,26 @@ static int s3c24xx_i2c_remove(struct platform_device *pdev) } #ifdef CONFIG_PM +static int s3c24xx_i2c_suspend_late(struct platform_device *dev, + pm_message_t msg) +{ + struct s3c24xx_i2c *i2c = platform_get_drvdata(dev); + i2c->suspended = 1; + return 0; +} + static int s3c24xx_i2c_resume(struct platform_device *dev) { struct s3c24xx_i2c *i2c = platform_get_drvdata(dev); - if (i2c != NULL) - s3c24xx_i2c_init(i2c); + i2c->suspended = 0; + s3c24xx_i2c_init(i2c); return 0; } #else +#define s3c24xx_i2c_suspend_late NULL #define s3c24xx_i2c_resume NULL #endif @@ -1005,6 +1015,7 @@ static int s3c24xx_i2c_resume(struct platform_device *dev) static struct platform_driver s3c2410_i2c_driver = { .probe = s3c24xx_i2c_probe, .remove = s3c24xx_i2c_remove, + .suspend_late = s3c24xx_i2c_suspend_late, .resume = s3c24xx_i2c_resume, .driver = { .owner = THIS_MODULE, @@ -1015,6 +1026,7 @@ static struct platform_driver s3c2410_i2c_driver = { static struct platform_driver s3c2440_i2c_driver = { .probe = s3c24xx_i2c_probe, .remove = s3c24xx_i2c_remove, + .suspend_late = s3c24xx_i2c_suspend_late, .resume = s3c24xx_i2c_resume, .driver = { .owner = THIS_MODULE, -- cgit v1.2.2 From 5413aa467806578bf5f78a83893cb9426b815231 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Wed, 3 Dec 2008 16:33:09 -0800 Subject: USB: fix problem with usbtmc driver not loading properly The usbtmc driver forgot to export its device table to userspace. Without this, it is never loaded properly when such a device is seen by the system. Cc: Marcel Janssen Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/usbtmc.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/usb/class/usbtmc.c b/drivers/usb/class/usbtmc.c index 8e74657f106c..43a863c5cc43 100644 --- a/drivers/usb/class/usbtmc.c +++ b/drivers/usb/class/usbtmc.c @@ -51,6 +51,7 @@ static struct usb_device_id usbtmc_devices[] = { { USB_INTERFACE_INFO(USB_CLASS_APP_SPEC, 3, 0), }, { 0, } /* terminating entry */ }; +MODULE_DEVICE_TABLE(usb, usbtmc_devices); /* * This structure is the capabilities for the device -- cgit v1.2.2 From 1393fce7189427bdb4d6115ca5566ca8d0fc86f3 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?CS=C3=89CSY=20L=C3=A1szl=C3=B3?= Date: Tue, 9 Dec 2008 23:39:14 +0100 Subject: USB: storage: unusual_devs.h: Nokia 3109c addition MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit 2.6.26(.x, cannot remember) could handle the microSD card in my Nokia 3109c attached via USB as mass storage, 2.6.27(.x, up to and included 2.6.27.8) cannot. Please find the attached patch which fixes this regression, and a copy of /proc/bus/usb/devices with my phone plugged in running with this patch on Frugalware. T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0421 ProdID=0063 Rev= 6.01 S: Manufacturer=Nokia S: Product=Nokia 3109c S: SerialNumber=359561013742570 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms From: CSÉCSY László Cc: Phil Dibowitz Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index e61f2bfc64ad..6573156f72a0 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -167,6 +167,13 @@ UNUSUAL_DEV( 0x0421, 0x005d, 0x0001, 0x0600, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY ), +/* Reported by CSECSY Laszlo */ +UNUSUAL_DEV( 0x0421, 0x0063, 0x0001, 0x0601, + "Nokia", + "Nokia 3109c", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_FIX_CAPACITY ), + /* Patch for Nokia 5310 capacity */ UNUSUAL_DEV( 0x0421, 0x006a, 0x0000, 0x0591, "Nokia", -- cgit v1.2.2 From 48e1a540e1e9ea62a2b3088a69ecf934f3172b14 Mon Sep 17 00:00:00 2001 From: Ozan Sener Date: Mon, 8 Dec 2008 19:15:45 +0200 Subject: USB: Unusual devs patch for Nokia 3500c T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0421 ProdID=0060 Rev= 5.51 S: Manufacturer=Nokia S: Product=Nokia 3500c S: SerialNumber=357687010280751 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms From: Ozan Sener Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 6573156f72a0..06bf064c4394 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -167,6 +167,13 @@ UNUSUAL_DEV( 0x0421, 0x005d, 0x0001, 0x0600, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY ), +/* Reported by Ozan Sener */ +UNUSUAL_DEV( 0x0421, 0x0060, 0x0551, 0x0551, + "Nokia", + "3500c", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_FIX_CAPACITY ), + /* Reported by CSECSY Laszlo */ UNUSUAL_DEV( 0x0421, 0x0063, 0x0001, 0x0601, "Nokia", -- cgit v1.2.2 From a4b188095912eee83d065f000dfe06f25919750b Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Mon, 1 Dec 2008 10:23:43 -0500 Subject: usb-storage: update unusual_devs entry for Nokia 5310 This patch (as1179) updates the unusual_devs entry for Nokia's 5310 phone to include a more recent firmware revision. This fixes Bugzilla #12099. Signed-off-by: Alan Stern Tested-by: Robson Roberto Souza Peixoto Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 06bf064c4394..bfcc1fe82518 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -182,7 +182,7 @@ UNUSUAL_DEV( 0x0421, 0x0063, 0x0001, 0x0601, US_FL_FIX_CAPACITY ), /* Patch for Nokia 5310 capacity */ -UNUSUAL_DEV( 0x0421, 0x006a, 0x0000, 0x0591, +UNUSUAL_DEV( 0x0421, 0x006a, 0x0000, 0x0701, "Nokia", "5310", US_SC_DEVICE, US_PR_DEVICE, NULL, -- cgit v1.2.2 From f2ee695554d9b4d163361a63f196ad7d8d0fe935 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Sat, 6 Dec 2008 23:46:04 -0800 Subject: USB: tty: SprogII DCC controller identifiers Someone on rmweb reminded me this had been overlooked from ages ago.. Add the identifiers for the Sprog II USB. This is a DCC control interface using the FTDI-SIO hardware: http://www.sprog-dcc.co.uk/. People have been using it with insmod options for ages, this just puts it into the driver data. Signed-off-by: Alan Cox Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio.h | 3 +++ 2 files changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index aad1359a3eb1..abbc2d8350af 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -166,6 +166,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_PID) }, { USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_IOBOARD_PID) }, { USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_MINI_IOBOARD_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_SPROG_II) }, { USB_DEVICE(FTDI_VID, FTDI_XF_632_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_634_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_547_PID) }, diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index 07a3992abad2..70703b706b09 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -75,6 +75,9 @@ /* OpenDCC (www.opendcc.de) product id */ #define FTDI_OPENDCC_PID 0xBFD8 +/* Sprog II (Andrew Crosland's SprogII DCC interface) */ +#define FTDI_SPROG_II 0xF0C8 + /* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */ /* they use the ftdi chipset for the USB interface and the vendor id is the same */ #define FTDI_XF_632_PID 0xFC08 /* 632: 16x2 Character Display */ -- cgit v1.2.2 From 01ba0856e9352e3c4e1c7d8c0a2a7defb456a5f9 Mon Sep 17 00:00:00 2001 From: Andrew Ewert Date: Thu, 4 Dec 2008 09:09:59 -0600 Subject: USB: ftdi_sio: Adding Ewert Energy System's CANdapter PID The following patch adds in the USB PID for Ewert Energy System's CANdapter device (CANBUS to USB-Serial which uses the FTDI 245R chipset) to the ftdi_sio device driver. The patch was tested successfully on Linux kernel 2.6.27 under Ubuntu. Relevant output from /proc/bus/usb/devices (With patch installed): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0403 ProdID=9f80 Rev= 6.00 S: Manufacturer=Ewert Energy Systems S: Product=CANdapter S: SerialNumber=A6RGB3Z3 C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 90mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=ftdi_sio E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms Signed-off-by: Andrew Ewert Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio.h | 3 +++ 2 files changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index abbc2d8350af..fb6f2933b01b 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -143,6 +143,7 @@ static struct ftdi_sio_quirk ftdi_HE_TIRA1_quirk = { static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_AMC232_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CANUSB_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_CANDAPTER_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_0_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_2_PID) }, diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index 70703b706b09..373ee09975bb 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -40,6 +40,9 @@ /* AlphaMicro Components AMC-232USB01 device */ #define FTDI_AMC232_PID 0xFF00 /* Product Id */ +/* www.candapter.com Ewert Energy Systems CANdapter device */ +#define FTDI_CANDAPTER_PID 0x9F80 /* Product Id */ + /* SCS HF Radio Modems PID's (http://www.scs-ptc.com) */ /* the VID is the standard ftdi vid (FTDI_VID) */ #define FTDI_SCS_DEVICE_0_PID 0xD010 /* SCS PTC-IIusb */ -- cgit v1.2.2 From 7c12414955e9b44a3e33d54e578bf008caa4475d Mon Sep 17 00:00:00 2001 From: David Brownell Date: Mon, 24 Nov 2008 23:11:03 -0800 Subject: USB: gadget: fix rndis working at high speed Fix a bug specific to highspeed mode in the recently updated RNDIS support: it wasn't setting up the high speed notification endpoint, which prevented high speed RNDIS links from working. Signed-off-by: David Brownell Tested-by: Anand Gadiyar Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/f_rndis.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/gadget/f_rndis.c b/drivers/usb/gadget/f_rndis.c index 428b5993575a..3a8bb53fc473 100644 --- a/drivers/usb/gadget/f_rndis.c +++ b/drivers/usb/gadget/f_rndis.c @@ -651,6 +651,8 @@ rndis_bind(struct usb_configuration *c, struct usb_function *f) fs_in_desc.bEndpointAddress; hs_out_desc.bEndpointAddress = fs_out_desc.bEndpointAddress; + hs_notify_desc.bEndpointAddress = + fs_notify_desc.bEndpointAddress; /* copy descriptors, and track endpoint copies */ f->hs_descriptors = usb_copy_descriptors(eth_hs_function); @@ -662,6 +664,8 @@ rndis_bind(struct usb_configuration *c, struct usb_function *f) f->hs_descriptors, &hs_in_desc); rndis->hs.out = usb_find_endpoint(eth_hs_function, f->hs_descriptors, &hs_out_desc); + rndis->hs.notify = usb_find_endpoint(eth_hs_function, + f->hs_descriptors, &hs_notify_desc); } rndis->port.open = rndis_open; -- cgit v1.2.2 From 24c0996a6b73e2554104961afcc8659534503e0d Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Mon, 1 Dec 2008 10:24:41 -0500 Subject: USB: skip Set-Interface(0) if already in altsetting 0 When a driver unbinds from an interface, usbcore always sends a Set-Interface request to reinstall altsetting 0. Unforunately, quite a few devices have buggy firmware that crashes when it receives this request. To avoid such problems, this patch (as1180) arranges to send the Set-Interface request only when the interface is not already in altsetting 0. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/driver.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index 3d7793d93031..8c081308b0e2 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -279,7 +279,9 @@ static int usb_unbind_interface(struct device *dev) * altsetting means creating new endpoint device entries). * When either of these happens, defer the Set-Interface. */ - if (!error && intf->dev.power.status == DPM_ON) + if (intf->cur_altsetting->desc.bAlternateSetting == 0) + ; /* Already in altsetting 0 so skip Set-Interface */ + else if (!error && intf->dev.power.status == DPM_ON) usb_set_interface(udev, intf->altsetting[0]. desc.bInterfaceNumber, 0); else -- cgit v1.2.2 From 7c99200142c04d0f1ed3f048014591f841efdaed Mon Sep 17 00:00:00 2001 From: Matthew Arnold Date: Sat, 13 Dec 2008 22:42:53 +1100 Subject: USB: add 5372:2303 to pl2303 This patch adds the "Superial" USB-Serial converter to pl2303 so that it is detected, by the correct driver. Adds the relevant vendor:product (5372:2303) to the device tables in pl2303.c & pl2303.h. The patch has been tested against 2.6.24-22-generic. Signed-off-by: Matthew D Arnold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/pl2303.c | 1 + drivers/usb/serial/pl2303.h | 4 ++++ 2 files changed, 5 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 491c8857b644..029b314a1fb2 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -91,6 +91,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(WS002IN_VENDOR_ID, WS002IN_PRODUCT_ID) }, { USB_DEVICE(COREGA_VENDOR_ID, COREGA_PRODUCT_ID) }, { USB_DEVICE(YCCABLE_VENDOR_ID, YCCABLE_PRODUCT_ID) }, + { USB_DEVICE(SUPERIAL_VENDOR_ID, SUPERIAL_PRODUCT_ID) }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h index a3bd039c78e9..05c909aca8e3 100644 --- a/drivers/usb/serial/pl2303.h +++ b/drivers/usb/serial/pl2303.h @@ -110,3 +110,7 @@ /* Y.C. Cable U.S.A., Inc - USB to RS-232 */ #define YCCABLE_VENDOR_ID 0x05ad #define YCCABLE_PRODUCT_ID 0x0fba + +/* "Superial" USB - Serial */ +#define SUPERIAL_VENDOR_ID 0x5372 +#define SUPERIAL_PRODUCT_ID 0x2303 -- cgit v1.2.2 From 413ba6fb51fa8dc77be09552e506d00f31234e0d Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Tue, 16 Dec 2008 12:25:55 +0100 Subject: USB: set correct configuration in probe of ti_usb_3410_5052 This driver transfers firmware. It may just as well set the correct configuration. Signed-off-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ti_usb_3410_5052.c | 55 ++--------------------------------- 1 file changed, 3 insertions(+), 52 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c index 31c42d1cae13..01d0c70d60e9 100644 --- a/drivers/usb/serial/ti_usb_3410_5052.c +++ b/drivers/usb/serial/ti_usb_3410_5052.c @@ -16,56 +16,6 @@ * For questions or problems with this driver, contact Texas Instruments * technical support, or Al Borchers , or * Peter Berger . - * - * This driver needs this hotplug script in /etc/hotplug/usb/ti_usb_3410_5052 - * or in /etc/hotplug.d/usb/ti_usb_3410_5052.hotplug to set the device - * configuration. - * - * #!/bin/bash - * - * BOOT_CONFIG=1 - * ACTIVE_CONFIG=2 - * - * if [[ "$ACTION" != "add" ]] - * then - * exit - * fi - * - * CONFIG_PATH=/sys${DEVPATH%/?*}/bConfigurationValue - * - * if [[ 0`cat $CONFIG_PATH` -ne $BOOT_CONFIG ]] - * then - * exit - * fi - * - * PRODUCT=${PRODUCT%/?*} # delete version - * VENDOR_ID=`printf "%d" 0x${PRODUCT%/?*}` - * PRODUCT_ID=`printf "%d" 0x${PRODUCT#*?/}` - * - * PARAM_PATH=/sys/module/ti_usb_3410_5052/parameters - * - * function scan() { - * s=$1 - * shift - * for i - * do - * if [[ $s -eq $i ]] - * then - * return 0 - * fi - * done - * return 1 - * } - * - * IFS=$IFS, - * - * if (scan $VENDOR_ID 1105 `cat $PARAM_PATH/vendor_3410` && - * scan $PRODUCT_ID 13328 `cat $PARAM_PATH/product_3410`) || - * (scan $VENDOR_ID 1105 `cat $PARAM_PATH/vendor_5052` && - * scan $PRODUCT_ID 20562 20818 20570 20575 `cat $PARAM_PATH/product_5052`) - * then - * echo $ACTIVE_CONFIG > $CONFIG_PATH - * fi */ #include @@ -457,9 +407,10 @@ static int ti_startup(struct usb_serial *serial) goto free_tdev; } - /* the second configuration must be set (in sysfs by hotplug script) */ + /* the second configuration must be set */ if (dev->actconfig->desc.bConfigurationValue == TI_BOOT_CONFIG) { - status = -ENODEV; + status = usb_driver_set_configuration(dev, TI_ACTIVE_CONFIG); + status = status ? status : -ENODEV; goto free_tdev; } -- cgit v1.2.2 From af4b8514aafd53d97b05a0a30b7d4cfd2cbb7b81 Mon Sep 17 00:00:00 2001 From: Mike Provencher Date: Tue, 16 Dec 2008 14:30:14 -0600 Subject: USB: pl2303: add id for Hewlett-Packard LD220-HP POS pole display Add id for the Hewlett-Packard LD220-HP POS pole display. Bus 002 Device 002: ID 03f0:3524 Hewlett-Packard Signed-off-by: Mike Provencher Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/pl2303.c | 1 + drivers/usb/serial/pl2303.h | 4 ++++ 2 files changed, 5 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 029b314a1fb2..1aed584be5eb 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -92,6 +92,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(COREGA_VENDOR_ID, COREGA_PRODUCT_ID) }, { USB_DEVICE(YCCABLE_VENDOR_ID, YCCABLE_PRODUCT_ID) }, { USB_DEVICE(SUPERIAL_VENDOR_ID, SUPERIAL_PRODUCT_ID) }, + { USB_DEVICE(HP_VENDOR_ID, HP_LD220_PRODUCT_ID) }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h index 05c909aca8e3..54974f446a8c 100644 --- a/drivers/usb/serial/pl2303.h +++ b/drivers/usb/serial/pl2303.h @@ -114,3 +114,7 @@ /* "Superial" USB - Serial */ #define SUPERIAL_VENDOR_ID 0x5372 #define SUPERIAL_PRODUCT_ID 0x2303 + +/* Hewlett-Packard LD220-HP POS Pole Display */ +#define HP_VENDOR_ID 0x03f0 +#define HP_LD220_PRODUCT_ID 0x3524 -- cgit v1.2.2 From 09a35ce00fa6bbb8bd130a828807e237488aa7ea Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Sat, 6 Dec 2008 21:10:51 -0800 Subject: xilinx_hwicap: remove improper wording in license statement GPLv2 doesn't allow additional restrictions to be imposed on any code, so this wording needs to be removed from these files. Signed-off-by: Stephen Neuendorffer Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/char/xilinx_hwicap/buffer_icap.c | 3 --- drivers/char/xilinx_hwicap/buffer_icap.h | 3 --- drivers/char/xilinx_hwicap/fifo_icap.c | 3 --- drivers/char/xilinx_hwicap/fifo_icap.h | 3 --- drivers/char/xilinx_hwicap/xilinx_hwicap.c | 3 --- drivers/char/xilinx_hwicap/xilinx_hwicap.h | 3 --- 6 files changed, 18 deletions(-) (limited to 'drivers') diff --git a/drivers/char/xilinx_hwicap/buffer_icap.c b/drivers/char/xilinx_hwicap/buffer_icap.c index aa7f7962a9a0..05d897764f02 100644 --- a/drivers/char/xilinx_hwicap/buffer_icap.c +++ b/drivers/char/xilinx_hwicap/buffer_icap.c @@ -21,9 +21,6 @@ * INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE. * - * Xilinx products are not intended for use in life support appliances, - * devices, or systems. Use in such applications is expressly prohibited. - * * (c) Copyright 2003-2008 Xilinx Inc. * All rights reserved. * diff --git a/drivers/char/xilinx_hwicap/buffer_icap.h b/drivers/char/xilinx_hwicap/buffer_icap.h index 8b0252bf06e2..d4f419ee87ab 100644 --- a/drivers/char/xilinx_hwicap/buffer_icap.h +++ b/drivers/char/xilinx_hwicap/buffer_icap.h @@ -21,9 +21,6 @@ * INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE. * - * Xilinx products are not intended for use in life support appliances, - * devices, or systems. Use in such applications is expressly prohibited. - * * (c) Copyright 2003-2008 Xilinx Inc. * All rights reserved. * diff --git a/drivers/char/xilinx_hwicap/fifo_icap.c b/drivers/char/xilinx_hwicap/fifo_icap.c index 776b50528478..02225eb19cf6 100644 --- a/drivers/char/xilinx_hwicap/fifo_icap.c +++ b/drivers/char/xilinx_hwicap/fifo_icap.c @@ -21,9 +21,6 @@ * INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE. * - * Xilinx products are not intended for use in life support appliances, - * devices, or systems. Use in such applications is expressly prohibited. - * * (c) Copyright 2007-2008 Xilinx Inc. * All rights reserved. * diff --git a/drivers/char/xilinx_hwicap/fifo_icap.h b/drivers/char/xilinx_hwicap/fifo_icap.h index 62bda453c90b..4c9dd9a3b62a 100644 --- a/drivers/char/xilinx_hwicap/fifo_icap.h +++ b/drivers/char/xilinx_hwicap/fifo_icap.h @@ -21,9 +21,6 @@ * INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE. * - * Xilinx products are not intended for use in life support appliances, - * devices, or systems. Use in such applications is expressly prohibited. - * * (c) Copyright 2007-2008 Xilinx Inc. * All rights reserved. * diff --git a/drivers/char/xilinx_hwicap/xilinx_hwicap.c b/drivers/char/xilinx_hwicap/xilinx_hwicap.c index d16131949097..f40ab699860f 100644 --- a/drivers/char/xilinx_hwicap/xilinx_hwicap.c +++ b/drivers/char/xilinx_hwicap/xilinx_hwicap.c @@ -21,9 +21,6 @@ * INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE. * - * Xilinx products are not intended for use in life support appliances, - * devices, or systems. Use in such applications is expressly prohibited. - * * (c) Copyright 2002 Xilinx Inc., Systems Engineering Group * (c) Copyright 2004 Xilinx Inc., Systems Engineering Group * (c) Copyright 2007-2008 Xilinx Inc. diff --git a/drivers/char/xilinx_hwicap/xilinx_hwicap.h b/drivers/char/xilinx_hwicap/xilinx_hwicap.h index 24d0d9b938fb..8cca11981c5f 100644 --- a/drivers/char/xilinx_hwicap/xilinx_hwicap.h +++ b/drivers/char/xilinx_hwicap/xilinx_hwicap.h @@ -21,9 +21,6 @@ * INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE. * - * Xilinx products are not intended for use in life support appliances, - * devices, or systems. Use in such applications is expressly prohibited. - * * (c) Copyright 2003-2007 Xilinx Inc. * All rights reserved. * -- cgit v1.2.2 From 4b4cdf3979c32fa3d042d150f49449c74d048553 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Fri, 28 Nov 2008 00:01:28 +0300 Subject: STAGING: Move staging drivers back to staging-specific menu Signed-off-by: Dmitry Baryshkov Signed-off-by: Greg Kroah-Hartman --- drivers/staging/Kconfig | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig index c95b286a1239..5d457c96bd7e 100644 --- a/drivers/staging/Kconfig +++ b/drivers/staging/Kconfig @@ -22,6 +22,8 @@ menuconfig STAGING If in doubt, say N here. +if STAGING + config STAGING_EXCLUDE_BUILD bool "Exclude Staging drivers from being built" if STAGING default y @@ -62,3 +64,4 @@ source "drivers/staging/at76_usb/Kconfig" source "drivers/staging/poch/Kconfig" endif # !STAGING_EXCLUDE_BUILD +endif # STAGING -- cgit v1.2.2