From 242ab7ad689accafd5e87ffd22b85cf1bf7fbbef Mon Sep 17 00:00:00 2001 From: Bob Copeland Date: Mon, 21 Dec 2009 22:26:48 -0500 Subject: ath5k: fix SWI calibration interrupt storm The calibration period is now invoked by triggering a software interrupt from within the ISR by ath5k_hw_calibration_poll() instead of via a timer. However, the calibration interval isn't initialized before interrupts are enabled, so we can have a situation where an interrupt occurs before the interval is assigned, so the interval is actually negative. As a result, the ISR will arm a software interrupt to schedule the tasklet, and then rearm it when the SWI is processed, and so on, leading to a softlockup at modprobe time. Move the initialization order around so the calibration interval is set before interrupts are active. Another possible fix is to schedule the tasklet directly from the poll routine, but I think there are additional plans for the SWI. Signed-off-by: Bob Copeland Cc: stable@kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath5k/base.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'drivers/net/wireless/ath') diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c index a4c086f069b1..2a446a938249 100644 --- a/drivers/net/wireless/ath/ath5k/base.c +++ b/drivers/net/wireless/ath/ath5k/base.c @@ -2381,6 +2381,9 @@ ath5k_init(struct ath5k_softc *sc) */ ath5k_stop_locked(sc); + /* Set PHY calibration interval */ + ah->ah_cal_intval = ath5k_calinterval; + /* * The basic interface to setting the hardware in a good * state is ``reset''. On return the hardware is known to @@ -2408,10 +2411,6 @@ ath5k_init(struct ath5k_softc *sc) /* Set ack to be sent at low bit-rates */ ath5k_hw_set_ack_bitrate_high(ah, false); - - /* Set PHY calibration inteval */ - ah->ah_cal_intval = ath5k_calinterval; - ret = 0; done: mmiowb(); -- cgit v1.2.2 From 671adc93b6472eaa0142a88d096c945f7b07893a Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Wed, 23 Dec 2009 13:12:04 +0100 Subject: wireless: remove remaining qual code This removes the remaining users of the rx status 'qual' field and the field itself. Signed-off-by: Johannes Berg Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath5k/base.c | 11 ----------- 1 file changed, 11 deletions(-) (limited to 'drivers/net/wireless/ath') diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c index 2a446a938249..e63b7c40d0ee 100644 --- a/drivers/net/wireless/ath/ath5k/base.c +++ b/drivers/net/wireless/ath/ath5k/base.c @@ -1903,17 +1903,6 @@ accept: rxs->noise = sc->ah->ah_noise_floor; rxs->signal = rxs->noise + rs.rs_rssi; - /* An rssi of 35 indicates you should be able use - * 54 Mbps reliably. A more elaborate scheme can be used - * here but it requires a map of SNR/throughput for each - * possible mode used */ - rxs->qual = rs.rs_rssi * 100 / 35; - - /* rssi can be more than 35 though, anything above that - * should be considered at 100% */ - if (rxs->qual > 100) - rxs->qual = 100; - rxs->antenna = rs.rs_antenna; rxs->rate_idx = ath5k_hw_to_driver_rix(sc, rs.rs_rate); rxs->flag |= ath5k_rx_decrypted(sc, ds, skb, &rs); -- cgit v1.2.2 From 83bd11a06da8bd119cc517de84b3214df3a7a6d4 Mon Sep 17 00:00:00 2001 From: Tobias Klauser Date: Wed, 23 Dec 2009 14:04:43 +0100 Subject: ath9k: Storage class should be before const qualifier The C99 specification states in section 6.11.5: The placement of a storage-class specifier other than at the beginning of the declaration specifiers in a declaration is an obsolescent feature. Signed-off-by: Tobias Klauser Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/wireless/ath') diff --git a/drivers/net/wireless/ath/ath9k/pci.c b/drivers/net/wireless/ath/ath9k/pci.c index 5321f735e5a0..f7af5ea54753 100644 --- a/drivers/net/wireless/ath/ath9k/pci.c +++ b/drivers/net/wireless/ath/ath9k/pci.c @@ -96,7 +96,7 @@ static void ath_pci_bt_coex_prep(struct ath_common *common) pci_write_config_byte(pdev, ATH_PCIE_CAP_LINK_CTRL, aspm); } -const static struct ath_bus_ops ath_pci_bus_ops = { +static const struct ath_bus_ops ath_pci_bus_ops = { .read_cachesize = ath_pci_read_cachesize, .cleanup = ath_pci_cleanup, .eeprom_read = ath_pci_eeprom_read, -- cgit v1.2.2 From 3867cf6a8c699846e928e8f5a9f31013708df192 Mon Sep 17 00:00:00 2001 From: Sujith Date: Wed, 23 Dec 2009 20:03:27 -0500 Subject: ath9k: fix suspend by waking device prior to stop Ensure the device is awake prior to trying to tell hardware to stop it. Impact of not doing this is we can likely leave the device in an undefined state likely causing issues with suspend and resume. This patch ensures harware is where it should be prior to suspend. Cc: stable@kernel.org Signed-off-by: Sujith Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/main.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers/net/wireless/ath') diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 9e68c1a8aef0..2ec7451350f0 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -2514,6 +2514,9 @@ static void ath9k_stop(struct ieee80211_hw *hw) return; /* another wiphy still in use */ } + /* Ensure HW is awake when we try to shut it down. */ + ath9k_ps_wakeup(sc); + if (ah->btcoex_hw.enabled) { ath9k_hw_btcoex_disable(ah); if (ah->btcoex_hw.scheme == ATH_BTCOEX_CFG_3WIRE) @@ -2534,6 +2537,9 @@ static void ath9k_stop(struct ieee80211_hw *hw) /* disable HAL and put h/w to sleep */ ath9k_hw_disable(ah); ath9k_hw_configpcipowersave(ah, 1, 1); + ath9k_ps_restore(sc); + + /* Finally, put the chip in FULL SLEEP mode */ ath9k_setpower(sc, ATH9K_PM_FULL_SLEEP); sc->sc_flags |= SC_OP_INVALID; -- cgit v1.2.2 From 5f70a88f631c3480107853cae12925185eb4c598 Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Wed, 23 Dec 2009 20:03:28 -0500 Subject: ath9k: wake hardware for interface IBSS/AP/Mesh removal When we remove a IBSS/AP/Mesh interface we stop DMA but to do this we should ensure hardware is on. Awaken the device prior to these calls. This should ensure DMA is stopped upon suspend and plain device removal. Cc: stable@kernel.org Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/main.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/net/wireless/ath') diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 2ec7451350f0..623ade8960c5 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -2653,8 +2653,10 @@ static void ath9k_remove_interface(struct ieee80211_hw *hw, if ((sc->sc_ah->opmode == NL80211_IFTYPE_AP) || (sc->sc_ah->opmode == NL80211_IFTYPE_ADHOC) || (sc->sc_ah->opmode == NL80211_IFTYPE_MESH_POINT)) { + ath9k_ps_wakeup(sc); ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq); ath_beacon_return(sc, avp); + ath9k_ps_restore(sc); } sc->sc_flags &= ~SC_OP_BEACONS; -- cgit v1.2.2 From 8b685ba9de803f210936400612a32a2003f47cd3 Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Wed, 23 Dec 2009 20:03:29 -0500 Subject: ath9k: wake hardware during AMPDU TX actions AMDPDU actions poke hardware for TX operation, as such we want to turn hardware on for these actions. AMDPU RX operations do not require hardware on as nothing is done in hardware for those actions. Without this we cannot guarantee hardware has been programmed correctly for each AMPDU TX action. Cc: stable@kernel.org Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/main.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers/net/wireless/ath') diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 623ade8960c5..996eb90263cc 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -3105,15 +3105,21 @@ static int ath9k_ampdu_action(struct ieee80211_hw *hw, case IEEE80211_AMPDU_RX_STOP: break; case IEEE80211_AMPDU_TX_START: + ath9k_ps_wakeup(sc); ath_tx_aggr_start(sc, sta, tid, ssn); ieee80211_start_tx_ba_cb_irqsafe(vif, sta->addr, tid); + ath9k_ps_restore(sc); break; case IEEE80211_AMPDU_TX_STOP: + ath9k_ps_wakeup(sc); ath_tx_aggr_stop(sc, sta, tid); ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid); + ath9k_ps_restore(sc); break; case IEEE80211_AMPDU_TX_OPERATIONAL: + ath9k_ps_wakeup(sc); ath_tx_aggr_resume(sc, sta, tid); + ath9k_ps_restore(sc); break; default: ath_print(ath9k_hw_common(sc->sc_ah), ATH_DBG_FATAL, -- cgit v1.2.2 From 5b479a076de091590423a9e6dfc2584126b28761 Mon Sep 17 00:00:00 2001 From: Felix Fietkau Date: Thu, 24 Dec 2009 14:04:32 +0100 Subject: ath9k: fix missed error codes in the tx status check MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit My previous change added in: commit 815833e7ecf0b9a017315cae6aef4d7cd9517681 ath9k: fix tx status reporting was not checking all possible tx error conditions. This could possibly lead to throughput issues due to slow rate control adaption or missed retransmissions of failed A-MPDU frames. This patch adds a mask for all possible error conditions and uses it in the xmit ok check. Cc: stable@kernel.org Reported-by: Björn Smedman Signed-off-by: Felix Fietkau Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/mac.h | 3 +++ drivers/net/wireless/ath/ath9k/xmit.c | 2 +- 2 files changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers/net/wireless/ath') diff --git a/drivers/net/wireless/ath/ath9k/mac.h b/drivers/net/wireless/ath/ath9k/mac.h index 0c87771383f0..e185479e295e 100644 --- a/drivers/net/wireless/ath/ath9k/mac.h +++ b/drivers/net/wireless/ath/ath9k/mac.h @@ -77,6 +77,9 @@ #define ATH9K_TXERR_XTXOP 0x08 #define ATH9K_TXERR_TIMER_EXPIRED 0x10 #define ATH9K_TX_ACKED 0x20 +#define ATH9K_TXERR_MASK \ + (ATH9K_TXERR_XRETRY | ATH9K_TXERR_FILT | ATH9K_TXERR_FIFO | \ + ATH9K_TXERR_XTXOP | ATH9K_TXERR_TIMER_EXPIRED) #define ATH9K_TX_BA 0x01 #define ATH9K_TX_PWRMGMT 0x02 diff --git a/drivers/net/wireless/ath/ath9k/xmit.c b/drivers/net/wireless/ath/ath9k/xmit.c index 1e813bbf474a..fa12b9060b0b 100644 --- a/drivers/net/wireless/ath/ath9k/xmit.c +++ b/drivers/net/wireless/ath/ath9k/xmit.c @@ -2072,7 +2072,7 @@ static void ath_tx_processq(struct ath_softc *sc, struct ath_txq *txq) &txq->axq_q, lastbf->list.prev); txq->axq_depth--; - txok = !(ds->ds_txstat.ts_status & ATH9K_TXERR_FILT); + txok = !(ds->ds_txstat.ts_status & ATH9K_TXERR_MASK); txq->axq_tx_inprogress = false; spin_unlock_bh(&txq->axq_lock); -- cgit v1.2.2