From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- drivers/net/tulip/Kconfig | 166 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 166 insertions(+) create mode 100644 drivers/net/tulip/Kconfig (limited to 'drivers/net/tulip/Kconfig') diff --git a/drivers/net/tulip/Kconfig b/drivers/net/tulip/Kconfig new file mode 100644 index 000000000000..e2cdaf876201 --- /dev/null +++ b/drivers/net/tulip/Kconfig @@ -0,0 +1,166 @@ +# +# Tulip family network device configuration +# + +menu "Tulip family network device support" + depends on NET_ETHERNET && (PCI || EISA || CARDBUS) + +config NET_TULIP + bool "\"Tulip\" family network device support" + help + This selects the "Tulip" family of EISA/PCI network cards. + +config DE2104X + tristate "Early DECchip Tulip (dc2104x) PCI support (EXPERIMENTAL)" + depends on NET_TULIP && PCI && EXPERIMENTAL + select CRC32 + ---help--- + This driver is developed for the SMC EtherPower series Ethernet + cards and also works with cards based on the DECchip + 21040 (Tulip series) chips. Some LinkSys PCI cards are + of this type. (If your card is NOT SMC EtherPower 10/100 PCI + (smc9332dst), you can also try the driver for "Generic DECchip" + cards, below. However, most people with a network card of this type + will say Y here.) Do read the Ethernet-HOWTO, available from + . + + To compile this driver as a module, choose M here and read + . The module will + be called de2104x. + +config TULIP + tristate "DECchip Tulip (dc2114x) PCI support" + depends on NET_TULIP && PCI + select CRC32 + ---help--- + This driver is developed for the SMC EtherPower series Ethernet + cards and also works with cards based on the DECchip + 21140 (Tulip series) chips. Some LinkSys PCI cards are + of this type. (If your card is NOT SMC EtherPower 10/100 PCI + (smc9332dst), you can also try the driver for "Generic DECchip" + cards, above. However, most people with a network card of this type + will say Y here.) Do read the Ethernet-HOWTO, available from + . + + To compile this driver as a module, choose M here and read + . The module will + be called tulip. + +config TULIP_MWI + bool "New bus configuration (EXPERIMENTAL)" + depends on TULIP && EXPERIMENTAL + help + This configures your Tulip card specifically for the card and + system cache line size type you are using. + + This is experimental code, not yet tested on many boards. + + If unsure, say N. + +config TULIP_MMIO + bool "Use PCI shared mem for NIC registers" + depends on TULIP + help + Use PCI shared memory for the NIC registers, rather than going through + the Tulip's PIO (programmed I/O ports). Faster, but could produce + obscure bugs if your mainboard has memory controller timing issues. + If in doubt, say N. + +config TULIP_NAPI + bool "Use NAPI RX polling " + depends on TULIP + help + NAPI is a new driver API designed to reduce CPU and interrupt load + when the driver is receiving lots of packets from the card. It is + still somewhat experimental and thus not yet enabled by default. + + If your estimated Rx load is 10kpps or more, or if the card will be + deployed on potentially unfriendly networks (e.g. in a firewall), + then say Y here. + + See for more + information. + + If in doubt, say N. + +config TULIP_NAPI_HW_MITIGATION + bool "Use Interrupt Mitigation " + depends on TULIP_NAPI + ---help--- + Use HW to reduce RX interrupts. Not strict necessary since NAPI reduces + RX interrupts but itself. Although this reduces RX interrupts even at + low levels traffic at the cost of a small latency. + + If in doubt, say Y. + +config DE4X5 + tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA" + depends on NET_TULIP && (PCI || EISA) + select CRC32 + ---help--- + This is support for the DIGITAL series of PCI/EISA Ethernet cards. + These include the DE425, DE434, DE435, DE450 and DE500 models. If + you have a network card of this type, say Y and read the + Ethernet-HOWTO, available from + . More specific + information is contained in + . + + To compile this driver as a module, choose M here and read + . The module will + be called de4x5. + +config WINBOND_840 + tristate "Winbond W89c840 Ethernet support" + depends on NET_TULIP && PCI + select CRC32 + select MII + help + This driver is for the Winbond W89c840 chip. It also works with + the TX9882 chip on the Compex RL100-ATX board. + More specific information and updates are available from + . + +config DM9102 + tristate "Davicom DM910x/DM980x support" + depends on NET_TULIP && PCI + select CRC32 + ---help--- + This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from + Davicom (). If you have such a network + (Ethernet) card, say Y. Some information is contained in the file + . + + To compile this driver as a module, choose M here and read + . The module will + be called dmfe. + +config PCMCIA_XIRCOM + tristate "Xircom CardBus support (new driver)" + depends on NET_TULIP && CARDBUS + ---help--- + This driver is for the Digital "Tulip" Ethernet CardBus adapters. + It should work with most DEC 21*4*-based chips/ethercards, as well + as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and + ASIX. + + To compile this driver as a module, choose M here and read + . The module will + be called xircom_cb. If unsure, say N. + +config PCMCIA_XIRTULIP + tristate "Xircom Tulip-like CardBus support (old driver)" + depends on NET_TULIP && CARDBUS && BROKEN_ON_SMP + select CRC32 + ---help--- + This driver is for the Digital "Tulip" Ethernet CardBus adapters. + It should work with most DEC 21*4*-based chips/ethercards, as well + as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and + ASIX. + + To compile this driver as a module, choose M here and read + . The module will + be called xircom_tulip_cb. If unsure, say N. + +endmenu + -- cgit v1.2.2