From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- drivers/ide/pci/hpt366.c | 1745 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1745 insertions(+) create mode 100644 drivers/ide/pci/hpt366.c (limited to 'drivers/ide/pci/hpt366.c') diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c new file mode 100644 index 000000000000..c8ee0b8c0292 --- /dev/null +++ b/drivers/ide/pci/hpt366.c @@ -0,0 +1,1745 @@ +/* + * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 + * + * Copyright (C) 1999-2003 Andre Hedrick + * Portions Copyright (C) 2001 Sun Microsystems, Inc. + * Portions Copyright (C) 2003 Red Hat Inc + * + * Thanks to HighPoint Technologies for their assistance, and hardware. + * Special Thanks to Jon Burchmore in SanDiego for the deep pockets, his + * donation of an ABit BP6 mainboard, processor, and memory acellerated + * development and support. + * + * Note that final HPT370 support was done by force extraction of GPL. + * + * - add function for getting/setting power status of drive + * - the HPT370's state machine can get confused. reset it before each dma + * xfer to prevent that from happening. + * - reset state engine whenever we get an error. + * - check for busmaster state at end of dma. + * - use new highpoint timings. + * - detect bus speed using highpoint register. + * - use pll if we don't have a clock table. added a 66MHz table that's + * just 2x the 33MHz table. + * - removed turnaround. NOTE: we never want to switch between pll and + * pci clocks as the chip can glitch in those cases. the highpoint + * approved workaround slows everything down too much to be useful. in + * addition, we would have to serialize access to each chip. + * Adrian Sun + * + * add drive timings for 66MHz PCI bus, + * fix ATA Cable signal detection, fix incorrect /proc info + * add /proc display for per-drive PIO/DMA/UDMA mode and + * per-channel ATA-33/66 Cable detect. + * Duncan Laurie + * + * fixup /proc output for multiple controllers + * Tim Hockin + * + * On hpt366: + * Reset the hpt366 on error, reset on dma + * Fix disabling Fast Interrupt hpt366. + * Mike Waychison + * + * Added support for 372N clocking and clock switching. The 372N needs + * different clocks on read/write. This requires overloading rw_disk and + * other deeply crazy things. Thanks to for + * keeping me sane. + * Alan Cox + * + */ + + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +/* various tuning parameters */ +#define HPT_RESET_STATE_ENGINE +#undef HPT_DELAY_INTERRUPT +#undef HPT_SERIALIZE_IO + +static const char *quirk_drives[] = { + "QUANTUM FIREBALLlct08 08", + "QUANTUM FIREBALLP KA6.4", + "QUANTUM FIREBALLP LM20.4", + "QUANTUM FIREBALLP LM20.5", + NULL +}; + +static const char *bad_ata100_5[] = { + "IBM-DTLA-307075", + "IBM-DTLA-307060", + "IBM-DTLA-307045", + "IBM-DTLA-307030", + "IBM-DTLA-307020", + "IBM-DTLA-307015", + "IBM-DTLA-305040", + "IBM-DTLA-305030", + "IBM-DTLA-305020", + "IC35L010AVER07-0", + "IC35L020AVER07-0", + "IC35L030AVER07-0", + "IC35L040AVER07-0", + "IC35L060AVER07-0", + "WDC AC310200R", + NULL +}; + +static const char *bad_ata66_4[] = { + "IBM-DTLA-307075", + "IBM-DTLA-307060", + "IBM-DTLA-307045", + "IBM-DTLA-307030", + "IBM-DTLA-307020", + "IBM-DTLA-307015", + "IBM-DTLA-305040", + "IBM-DTLA-305030", + "IBM-DTLA-305020", + "IC35L010AVER07-0", + "IC35L020AVER07-0", + "IC35L030AVER07-0", + "IC35L040AVER07-0", + "IC35L060AVER07-0", + "WDC AC310200R", + NULL +}; + +static const char *bad_ata66_3[] = { + "WDC AC310200R", + NULL +}; + +static const char *bad_ata33[] = { + "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2", + "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", + "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", + "Maxtor 90510D4", + "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", + "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", + "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", + NULL +}; + +struct chipset_bus_clock_list_entry { + u8 xfer_speed; + unsigned int chipset_settings; +}; + +/* key for bus clock timings + * bit + * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file + * register access. + * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file + * register access. + * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. + * during task file register access. + * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA + * xfer. + * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task + * register access. + * 28 UDMA enable + * 29 DMA enable + * 30 PIO_MST enable. if set, the chip is in bus master mode during + * PIO. + * 31 FIFO enable. + */ +static struct chipset_bus_clock_list_entry forty_base_hpt366[] = { + { XFER_UDMA_4, 0x900fd943 }, + { XFER_UDMA_3, 0x900ad943 }, + { XFER_UDMA_2, 0x900bd943 }, + { XFER_UDMA_1, 0x9008d943 }, + { XFER_UDMA_0, 0x9008d943 }, + + { XFER_MW_DMA_2, 0xa008d943 }, + { XFER_MW_DMA_1, 0xa010d955 }, + { XFER_MW_DMA_0, 0xa010d9fc }, + + { XFER_PIO_4, 0xc008d963 }, + { XFER_PIO_3, 0xc010d974 }, + { XFER_PIO_2, 0xc010d997 }, + { XFER_PIO_1, 0xc010d9c7 }, + { XFER_PIO_0, 0xc018d9d9 }, + { 0, 0x0120d9d9 } +}; + +static struct chipset_bus_clock_list_entry thirty_three_base_hpt366[] = { + { XFER_UDMA_4, 0x90c9a731 }, + { XFER_UDMA_3, 0x90cfa731 }, + { XFER_UDMA_2, 0x90caa731 }, + { XFER_UDMA_1, 0x90cba731 }, + { XFER_UDMA_0, 0x90c8a731 }, + + { XFER_MW_DMA_2, 0xa0c8a731 }, + { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */ + { XFER_MW_DMA_0, 0xa0c8a797 }, + + { XFER_PIO_4, 0xc0c8a731 }, + { XFER_PIO_3, 0xc0c8a742 }, + { XFER_PIO_2, 0xc0d0a753 }, + { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */ + { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */ + { 0, 0x0120a7a7 } +}; + +static struct chipset_bus_clock_list_entry twenty_five_base_hpt366[] = { + { XFER_UDMA_4, 0x90c98521 }, + { XFER_UDMA_3, 0x90cf8521 }, + { XFER_UDMA_2, 0x90cf8521 }, + { XFER_UDMA_1, 0x90cb8521 }, + { XFER_UDMA_0, 0x90cb8521 }, + + { XFER_MW_DMA_2, 0xa0ca8521 }, + { XFER_MW_DMA_1, 0xa0ca8532 }, + { XFER_MW_DMA_0, 0xa0ca8575 }, + + { XFER_PIO_4, 0xc0ca8521 }, + { XFER_PIO_3, 0xc0ca8532 }, + { XFER_PIO_2, 0xc0ca8542 }, + { XFER_PIO_1, 0xc0d08572 }, + { XFER_PIO_0, 0xc0d08585 }, + { 0, 0x01208585 } +}; + +/* from highpoint documentation. these are old values */ +static struct chipset_bus_clock_list_entry thirty_three_base_hpt370[] = { +/* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */ + { XFER_UDMA_5, 0x16454e31 }, + { XFER_UDMA_4, 0x16454e31 }, + { XFER_UDMA_3, 0x166d4e31 }, + { XFER_UDMA_2, 0x16494e31 }, + { XFER_UDMA_1, 0x164d4e31 }, + { XFER_UDMA_0, 0x16514e31 }, + + { XFER_MW_DMA_2, 0x26514e21 }, + { XFER_MW_DMA_1, 0x26514e33 }, + { XFER_MW_DMA_0, 0x26514e97 }, + + { XFER_PIO_4, 0x06514e21 }, + { XFER_PIO_3, 0x06514e22 }, + { XFER_PIO_2, 0x06514e33 }, + { XFER_PIO_1, 0x06914e43 }, + { XFER_PIO_0, 0x06914e57 }, + { 0, 0x06514e57 } +}; + +static struct chipset_bus_clock_list_entry sixty_six_base_hpt370[] = { + { XFER_UDMA_5, 0x14846231 }, + { XFER_UDMA_4, 0x14886231 }, + { XFER_UDMA_3, 0x148c6231 }, + { XFER_UDMA_2, 0x148c6231 }, + { XFER_UDMA_1, 0x14906231 }, + { XFER_UDMA_0, 0x14986231 }, + + { XFER_MW_DMA_2, 0x26514e21 }, + { XFER_MW_DMA_1, 0x26514e33 }, + { XFER_MW_DMA_0, 0x26514e97 }, + + { XFER_PIO_4, 0x06514e21 }, + { XFER_PIO_3, 0x06514e22 }, + { XFER_PIO_2, 0x06514e33 }, + { XFER_PIO_1, 0x06914e43 }, + { XFER_PIO_0, 0x06914e57 }, + { 0, 0x06514e57 } +}; + +/* these are the current (4 sep 2001) timings from highpoint */ +static struct chipset_bus_clock_list_entry thirty_three_base_hpt370a[] = { + { XFER_UDMA_5, 0x12446231 }, + { XFER_UDMA_4, 0x12446231 }, + { XFER_UDMA_3, 0x126c6231 }, + { XFER_UDMA_2, 0x12486231 }, + { XFER_UDMA_1, 0x124c6233 }, + { XFER_UDMA_0, 0x12506297 }, + + { XFER_MW_DMA_2, 0x22406c31 }, + { XFER_MW_DMA_1, 0x22406c33 }, + { XFER_MW_DMA_0, 0x22406c97 }, + + { XFER_PIO_4, 0x06414e31 }, + { XFER_PIO_3, 0x06414e42 }, + { XFER_PIO_2, 0x06414e53 }, + { XFER_PIO_1, 0x06814e93 }, + { XFER_PIO_0, 0x06814ea7 }, + { 0, 0x06814ea7 } +}; + +/* 2x 33MHz timings */ +static struct chipset_bus_clock_list_entry sixty_six_base_hpt370a[] = { + { XFER_UDMA_5, 0x1488e673 }, + { XFER_UDMA_4, 0x1488e673 }, + { XFER_UDMA_3, 0x1498e673 }, + { XFER_UDMA_2, 0x1490e673 }, + { XFER_UDMA_1, 0x1498e677 }, + { XFER_UDMA_0, 0x14a0e73f }, + + { XFER_MW_DMA_2, 0x2480fa73 }, + { XFER_MW_DMA_1, 0x2480fa77 }, + { XFER_MW_DMA_0, 0x2480fb3f }, + + { XFER_PIO_4, 0x0c82be73 }, + { XFER_PIO_3, 0x0c82be95 }, + { XFER_PIO_2, 0x0c82beb7 }, + { XFER_PIO_1, 0x0d02bf37 }, + { XFER_PIO_0, 0x0d02bf5f }, + { 0, 0x0d02bf5f } +}; + +static struct chipset_bus_clock_list_entry fifty_base_hpt370a[] = { + { XFER_UDMA_5, 0x12848242 }, + { XFER_UDMA_4, 0x12ac8242 }, + { XFER_UDMA_3, 0x128c8242 }, + { XFER_UDMA_2, 0x120c8242 }, + { XFER_UDMA_1, 0x12148254 }, + { XFER_UDMA_0, 0x121882ea }, + + { XFER_MW_DMA_2, 0x22808242 }, + { XFER_MW_DMA_1, 0x22808254 }, + { XFER_MW_DMA_0, 0x228082ea }, + + { XFER_PIO_4, 0x0a81f442 }, + { XFER_PIO_3, 0x0a81f443 }, + { XFER_PIO_2, 0x0a81f454 }, + { XFER_PIO_1, 0x0ac1f465 }, + { XFER_PIO_0, 0x0ac1f48a }, + { 0, 0x0ac1f48a } +}; + +static struct chipset_bus_clock_list_entry thirty_three_base_hpt372[] = { + { XFER_UDMA_6, 0x1c81dc62 }, + { XFER_UDMA_5, 0x1c6ddc62 }, + { XFER_UDMA_4, 0x1c8ddc62 }, + { XFER_UDMA_3, 0x1c8edc62 }, /* checkme */ + { XFER_UDMA_2, 0x1c91dc62 }, + { XFER_UDMA_1, 0x1c9adc62 }, /* checkme */ + { XFER_UDMA_0, 0x1c82dc62 }, /* checkme */ + + { XFER_MW_DMA_2, 0x2c829262 }, + { XFER_MW_DMA_1, 0x2c829266 }, /* checkme */ + { XFER_MW_DMA_0, 0x2c82922e }, /* checkme */ + + { XFER_PIO_4, 0x0c829c62 }, + { XFER_PIO_3, 0x0c829c84 }, + { XFER_PIO_2, 0x0c829ca6 }, + { XFER_PIO_1, 0x0d029d26 }, + { XFER_PIO_0, 0x0d029d5e }, + { 0, 0x0d029d5e } +}; + +static struct chipset_bus_clock_list_entry fifty_base_hpt372[] = { + { XFER_UDMA_5, 0x12848242 }, + { XFER_UDMA_4, 0x12ac8242 }, + { XFER_UDMA_3, 0x128c8242 }, + { XFER_UDMA_2, 0x120c8242 }, + { XFER_UDMA_1, 0x12148254 }, + { XFER_UDMA_0, 0x121882ea }, + + { XFER_MW_DMA_2, 0x22808242 }, + { XFER_MW_DMA_1, 0x22808254 }, + { XFER_MW_DMA_0, 0x228082ea }, + + { XFER_PIO_4, 0x0a81f442 }, + { XFER_PIO_3, 0x0a81f443 }, + { XFER_PIO_2, 0x0a81f454 }, + { XFER_PIO_1, 0x0ac1f465 }, + { XFER_PIO_0, 0x0ac1f48a }, + { 0, 0x0a81f443 } +}; + +static struct chipset_bus_clock_list_entry sixty_six_base_hpt372[] = { + { XFER_UDMA_6, 0x1c869c62 }, + { XFER_UDMA_5, 0x1cae9c62 }, + { XFER_UDMA_4, 0x1c8a9c62 }, + { XFER_UDMA_3, 0x1c8e9c62 }, + { XFER_UDMA_2, 0x1c929c62 }, + { XFER_UDMA_1, 0x1c9a9c62 }, + { XFER_UDMA_0, 0x1c829c62 }, + + { XFER_MW_DMA_2, 0x2c829c62 }, + { XFER_MW_DMA_1, 0x2c829c66 }, + { XFER_MW_DMA_0, 0x2c829d2e }, + + { XFER_PIO_4, 0x0c829c62 }, + { XFER_PIO_3, 0x0c829c84 }, + { XFER_PIO_2, 0x0c829ca6 }, + { XFER_PIO_1, 0x0d029d26 }, + { XFER_PIO_0, 0x0d029d5e }, + { 0, 0x0d029d26 } +}; + +static struct chipset_bus_clock_list_entry thirty_three_base_hpt374[] = { + { XFER_UDMA_6, 0x12808242 }, + { XFER_UDMA_5, 0x12848242 }, + { XFER_UDMA_4, 0x12ac8242 }, + { XFER_UDMA_3, 0x128c8242 }, + { XFER_UDMA_2, 0x120c8242 }, + { XFER_UDMA_1, 0x12148254 }, + { XFER_UDMA_0, 0x121882ea }, + + { XFER_MW_DMA_2, 0x22808242 }, + { XFER_MW_DMA_1, 0x22808254 }, + { XFER_MW_DMA_0, 0x228082ea }, + + { XFER_PIO_4, 0x0a81f442 }, + { XFER_PIO_3, 0x0a81f443 }, + { XFER_PIO_2, 0x0a81f454 }, + { XFER_PIO_1, 0x0ac1f465 }, + { XFER_PIO_0, 0x0ac1f48a }, + { 0, 0x06814e93 } +}; + +/* FIXME: 50MHz timings for HPT374 */ + +#if 0 +static struct chipset_bus_clock_list_entry sixty_six_base_hpt374[] = { + { XFER_UDMA_6, 0x12406231 }, /* checkme */ + { XFER_UDMA_5, 0x12446231 }, /* 0x14846231 */ + { XFER_UDMA_4, 0x16814ea7 }, /* 0x14886231 */ + { XFER_UDMA_3, 0x16814ea7 }, /* 0x148c6231 */ + { XFER_UDMA_2, 0x16814ea7 }, /* 0x148c6231 */ + { XFER_UDMA_1, 0x16814ea7 }, /* 0x14906231 */ + { XFER_UDMA_0, 0x16814ea7 }, /* 0x14986231 */ + { XFER_MW_DMA_2, 0x16814ea7 }, /* 0x26514e21 */ + { XFER_MW_DMA_1, 0x16814ea7 }, /* 0x26514e97 */ + { XFER_MW_DMA_0, 0x16814ea7 }, /* 0x26514e97 */ + { XFER_PIO_4, 0x06814ea7 }, /* 0x06514e21 */ + { XFER_PIO_3, 0x06814ea7 }, /* 0x06514e22 */ + { XFER_PIO_2, 0x06814ea7 }, /* 0x06514e33 */ + { XFER_PIO_1, 0x06814ea7 }, /* 0x06914e43 */ + { XFER_PIO_0, 0x06814ea7 }, /* 0x06914e57 */ + { 0, 0x06814ea7 } +}; +#endif + +#define HPT366_DEBUG_DRIVE_INFO 0 +#define HPT374_ALLOW_ATA133_6 0 +#define HPT371_ALLOW_ATA133_6 0 +#define HPT302_ALLOW_ATA133_6 0 +#define HPT372_ALLOW_ATA133_6 1 +#define HPT370_ALLOW_ATA100_5 1 +#define HPT366_ALLOW_ATA66_4 1 +#define HPT366_ALLOW_ATA66_3 1 +#define HPT366_MAX_DEVS 8 + +#define F_LOW_PCI_33 0x23 +#define F_LOW_PCI_40 0x29 +#define F_LOW_PCI_50 0x2d +#define F_LOW_PCI_66 0x42 + +/* FIXME: compare with driver's code before removing */ +#if 0 + if (hpt_minimum_revision(dev, 3)) { + u8 cbl; + cbl = inb(iobase + 0x7b); + outb(cbl | 1, iobase + 0x7b); + outb(cbl & ~1, iobase + 0x7b); + cbl = inb(iobase + 0x7a); + p += sprintf(p, "Cable: ATA-%d" + " ATA-%d\n", + (cbl & 0x02) ? 33 : 66, + (cbl & 0x01) ? 33 : 66); + p += sprintf(p, "\n"); + } + { + u8 c2, c3; + /* older revs don't have these registers mapped + * into io space */ + pci_read_config_byte(dev, 0x43, &c0); + pci_read_config_byte(dev, 0x47, &c1); + pci_read_config_byte(dev, 0x4b, &c2); + pci_read_config_byte(dev, 0x4f, &c3); + + p += sprintf(p, "Mode: %s %s" + " %s %s\n", + (c0 & 0x10) ? "UDMA" : (c0 & 0x20) ? "DMA " : + (c0 & 0x80) ? "PIO " : "off ", + (c1 & 0x10) ? "UDMA" : (c1 & 0x20) ? "DMA " : + (c1 & 0x80) ? "PIO " : "off ", + (c2 & 0x10) ? "UDMA" : (c2 & 0x20) ? "DMA " : + (c2 & 0x80) ? "PIO " : "off ", + (c3 & 0x10) ? "UDMA" : (c3 & 0x20) ? "DMA " : + (c3 & 0x80) ? "PIO " : "off "); + } + } +#endif + +static u32 hpt_revision (struct pci_dev *dev) +{ + u32 class_rev; + pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); + class_rev &= 0xff; + + switch(dev->device) { + /* Remap new 372N onto 372 */ + case PCI_DEVICE_ID_TTI_HPT372N: + class_rev = PCI_DEVICE_ID_TTI_HPT372; break; + case PCI_DEVICE_ID_TTI_HPT374: + class_rev = PCI_DEVICE_ID_TTI_HPT374; break; + case PCI_DEVICE_ID_TTI_HPT371: + class_rev = PCI_DEVICE_ID_TTI_HPT371; break; + case PCI_DEVICE_ID_TTI_HPT302: + class_rev = PCI_DEVICE_ID_TTI_HPT302; break; + case PCI_DEVICE_ID_TTI_HPT372: + class_rev = PCI_DEVICE_ID_TTI_HPT372; break; + default: + break; + } + return class_rev; +} + +static u32 hpt_minimum_revision (struct pci_dev *dev, int revision) +{ + unsigned int class_rev = hpt_revision(dev); + revision--; + return ((int) (class_rev > revision) ? 1 : 0); +} + +static int check_in_drive_lists(ide_drive_t *drive, const char **list); + +static u8 hpt3xx_ratemask (ide_drive_t *drive) +{ + struct pci_dev *dev = HWIF(drive)->pci_dev; + u8 mode = 0; + + if (hpt_minimum_revision(dev, 8)) { /* HPT374 */ + mode = (HPT374_ALLOW_ATA133_6) ? 4 : 3; + } else if (hpt_minimum_revision(dev, 7)) { /* HPT371 */ + mode = (HPT371_ALLOW_ATA133_6) ? 4 : 3; + } else if (hpt_minimum_revision(dev, 6)) { /* HPT302 */ + mode = (HPT302_ALLOW_ATA133_6) ? 4 : 3; + } else if (hpt_minimum_revision(dev, 5)) { /* HPT372 */ + mode = (HPT372_ALLOW_ATA133_6) ? 4 : 3; + } else if (hpt_minimum_revision(dev, 4)) { /* HPT370A */ + mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2; + } else if (hpt_minimum_revision(dev, 3)) { /* HPT370 */ + mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2; + mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : mode; + } else { /* HPT366 and HPT368 */ + mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : 2; + } + if (!eighty_ninty_three(drive) && (mode)) + mode = min(mode, (u8)1); + return mode; +} + +/* + * Note for the future; the SATA hpt37x we must set + * either PIO or UDMA modes 0,4,5 + */ + +static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed) +{ + struct pci_dev *dev = HWIF(drive)->pci_dev; + u8 mode = hpt3xx_ratemask(drive); + + if (drive->media != ide_disk) + return min(speed, (u8)XFER_PIO_4); + + switch(mode) { + case 0x04: + speed = min(speed, (u8)XFER_UDMA_6); + break; + case 0x03: + speed = min(speed, (u8)XFER_UDMA_5); + if (hpt_minimum_revision(dev, 5)) + break; + if (check_in_drive_lists(drive, bad_ata100_5)) + speed = min(speed, (u8)XFER_UDMA_4); + break; + case 0x02: + speed = min(speed, (u8)XFER_UDMA_4); + /* + * CHECK ME, Does this need to be set to 5 ?? + */ + if (hpt_minimum_revision(dev, 3)) + break; + if ((check_in_drive_lists(drive, bad_ata66_4)) || + (!(HPT366_ALLOW_ATA66_4))) + speed = min(speed, (u8)XFER_UDMA_3); + if ((check_in_drive_lists(drive, bad_ata66_3)) || + (!(HPT366_ALLOW_ATA66_3))) + speed = min(speed, (u8)XFER_UDMA_2); + break; + case 0x01: + speed = min(speed, (u8)XFER_UDMA_2); + /* + * CHECK ME, Does this need to be set to 5 ?? + */ + if (hpt_minimum_revision(dev, 3)) + break; + if (check_in_drive_lists(drive, bad_ata33)) + speed = min(speed, (u8)XFER_MW_DMA_2); + break; + case 0x00: + default: + speed = min(speed, (u8)XFER_MW_DMA_2); + break; + } + return speed; +} + +static int check_in_drive_lists (ide_drive_t *drive, const char **list) +{ + struct hd_driveid *id = drive->id; + + if (quirk_drives == list) { + while (*list) + if (strstr(id->model, *list++)) + return 1; + } else { + while (*list) + if (!strcmp(*list++,id->model)) + return 1; + } + return 0; +} + +static unsigned int pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_entry * chipset_table) +{ + for ( ; chipset_table->xfer_speed ; chipset_table++) + if (chipset_table->xfer_speed == speed) + return chipset_table->chipset_settings; + return chipset_table->chipset_settings; +} + +static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed) +{ + struct pci_dev *dev = HWIF(drive)->pci_dev; + u8 speed = hpt3xx_ratefilter(drive, xferspeed); +// u8 speed = ide_rate_filter(hpt3xx_ratemask(drive), xferspeed); + u8 regtime = (drive->select.b.unit & 0x01) ? 0x44 : 0x40; + u8 regfast = (HWIF(drive)->channel) ? 0x55 : 0x51; + u8 drive_fast = 0; + u32 reg1 = 0, reg2 = 0; + + /* + * Disable the "fast interrupt" prediction. + */ + pci_read_config_byte(dev, regfast, &drive_fast); +#if 0 + if (drive_fast & 0x02) + pci_write_config_byte(dev, regfast, drive_fast & ~0x20); +#else + if (drive_fast & 0x80) + pci_write_config_byte(dev, regfast, drive_fast & ~0x80); +#endif + + reg2 = pci_bus_clock_list(speed, + (struct chipset_bus_clock_list_entry *) pci_get_drvdata(dev)); + /* + * Disable on-chip PIO FIFO/buffer + * (to avoid problems handling I/O errors later) + */ + pci_read_config_dword(dev, regtime, ®1); + if (speed >= XFER_MW_DMA_0) { + reg2 = (reg2 & ~0xc0000000) | (reg1 & 0xc0000000); + } else { + reg2 = (reg2 & ~0x30070000) | (reg1 & 0x30070000); + } + reg2 &= ~0x80000000; + + pci_write_config_dword(dev, regtime, reg2); + + return ide_config_drive_speed(drive, speed); +} + +static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed) +{ + struct pci_dev *dev = HWIF(drive)->pci_dev; + u8 speed = hpt3xx_ratefilter(drive, xferspeed); +// u8 speed = ide_rate_filter(hpt3xx_ratemask(drive), xferspeed); + u8 regfast = (HWIF(drive)->channel) ? 0x55 : 0x51; + u8 drive_pci = 0x40 + (drive->dn * 4); + u8 new_fast = 0, drive_fast = 0; + u32 list_conf = 0, drive_conf = 0; + u32 conf_mask = (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000; + + /* + * Disable the "fast interrupt" prediction. + * don't holdoff on interrupts. (== 0x01 despite what the docs say) + */ + pci_read_config_byte(dev, regfast, &drive_fast); + new_fast = drive_fast; + if (new_fast & 0x02) + new_fast &= ~0x02; + +#ifdef HPT_DELAY_INTERRUPT + if (new_fast & 0x01) + new_fast &= ~0x01; +#else + if ((new_fast & 0x01) == 0) + new_fast |= 0x01; +#endif + if (new_fast != drive_fast) + pci_write_config_byte(dev, regfast, new_fast); + + list_conf = pci_bus_clock_list(speed, + (struct chipset_bus_clock_list_entry *) + pci_get_drvdata(dev)); + + pci_read_config_dword(dev, drive_pci, &drive_conf); + list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask); + + if (speed < XFER_MW_DMA_0) { + list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */ + } + + pci_write_config_dword(dev, drive_pci, list_conf); + + return ide_config_drive_speed(drive, speed); +} + +static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed) +{ + struct pci_dev *dev = HWIF(drive)->pci_dev; + u8 speed = hpt3xx_ratefilter(drive, xferspeed); +// u8 speed = ide_rate_filter(hpt3xx_ratemask(drive), xferspeed); + u8 regfast = (HWIF(drive)->channel) ? 0x55 : 0x51; + u8 drive_fast = 0, drive_pci = 0x40 + (drive->dn * 4); + u32 list_conf = 0, drive_conf = 0; + u32 conf_mask = (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000; + + /* + * Disable the "fast interrupt" prediction. + * don't holdoff on interrupts. (== 0x01 despite what the docs say) + */ + pci_read_config_byte(dev, regfast, &drive_fast); + drive_fast &= ~0x07; + pci_write_config_byte(dev, regfast, drive_fast); + + list_conf = pci_bus_clock_list(speed, + (struct chipset_bus_clock_list_entry *) + pci_get_drvdata(dev)); + pci_read_config_dword(dev, drive_pci, &drive_conf); + list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask); + if (speed < XFER_MW_DMA_0) + list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */ + pci_write_config_dword(dev, drive_pci, list_conf); + + return ide_config_drive_speed(drive, speed); +} + +static int hpt3xx_tune_chipset (ide_drive_t *drive, u8 speed) +{ + struct pci_dev *dev = HWIF(drive)->pci_dev; + + if (hpt_minimum_revision(dev, 8)) + return hpt372_tune_chipset(drive, speed); /* not a typo */ +#if 0 + else if (hpt_minimum_revision(dev, 7)) + hpt371_tune_chipset(drive, speed); + else if (hpt_minimum_revision(dev, 6)) + hpt302_tune_chipset(drive, speed); +#endif + else if (hpt_minimum_revision(dev, 5)) + return hpt372_tune_chipset(drive, speed); + else if (hpt_minimum_revision(dev, 3)) + return hpt370_tune_chipset(drive, speed); + else /* hpt368: hpt_minimum_revision(dev, 2) */ + return hpt36x_tune_chipset(drive, speed); +} + +static void hpt3xx_tune_drive (ide_drive_t *drive, u8 pio) +{ + pio = ide_get_best_pio_mode(drive, 255, pio, NULL); + (void) hpt3xx_tune_chipset(drive, (XFER_PIO_0 + pio)); +} + +/* + * This allows the configuration of ide_pci chipset registers + * for cards that learn about the drive's UDMA, DMA, PIO capabilities + * after the drive is reported by the OS. Initially for designed for + * HPT366 UDMA chipset by HighPoint|Triones Technologies, Inc. + * + * check_in_drive_lists(drive, bad_ata66_4) + * check_in_drive_lists(drive, bad_ata66_3) + * check_in_drive_lists(drive, bad_ata33) + * + */ +static int config_chipset_for_dma (ide_drive_t *drive) +{ + u8 speed = ide_dma_speed(drive, hpt3xx_ratemask(drive)); + + if (!(speed)) + return 0; + + (void) hpt3xx_tune_chipset(drive, speed); + return ide_dma_enable(drive); +} + +static int hpt3xx_quirkproc (ide_drive_t *drive) +{ + return ((int) check_in_drive_lists(drive, quirk_drives)); +} + +static void hpt3xx_intrproc (ide_drive_t *drive) +{ + ide_hwif_t *hwif = HWIF(drive); + + if (drive->quirk_list) + return; + /* drives in the quirk_list may not like intr setups/cleanups */ + hwif->OUTB(drive->ctl|2, IDE_CONTROL_REG); +} + +static void hpt3xx_maskproc (ide_drive_t *drive, int mask) +{ + struct pci_dev *dev = HWIF(drive)->pci_dev; + + if (drive->quirk_list) { + if (hpt_minimum_revision(dev,3)) { + u8 reg5a = 0; + pci_read_config_byte(dev, 0x5a, ®5a); + if (((reg5a & 0x10) >> 4) != mask) + pci_write_config_byte(dev, 0x5a, mask ? (reg5a | 0x10) : (reg5a & ~0x10)); + } else { + if (mask) { + disable_irq(HWIF(drive)->irq); + } else { + enable_irq(HWIF(drive)->irq); + } + } + } else { + if (IDE_CONTROL_REG) + HWIF(drive)->OUTB(mask ? (drive->ctl | 2) : + (drive->ctl & ~2), + IDE_CONTROL_REG); + } +} + +static int hpt366_config_drive_xfer_rate (ide_drive_t *drive) +{ + ide_hwif_t *hwif = HWIF(drive); + struct hd_driveid *id = drive->id; + + drive->init_speed = 0; + + if (id && (id->capability & 1) && drive->autodma) { + + if (ide_use_dma(drive)) { + if (config_chipset_for_dma(drive)) + return hwif->ide_dma_on(drive); + } + + goto fast_ata_pio; + + } else if ((id->capability & 8) || (id->field_valid & 2)) { +fast_ata_pio: + hpt3xx_tune_drive(drive, 5); + return hwif->ide_dma_off_quietly(drive); + } + /* IORDY not supported */ + return 0; +} + +/* + * This is specific to the HPT366 UDMA bios chipset + * by HighPoint|Triones Technologies, Inc. + */ +static int hpt366_ide_dma_lostirq (ide_drive_t *drive) +{ + struct pci_dev *dev = HWIF(drive)->pci_dev; + u8 reg50h = 0, reg52h = 0, reg5ah = 0; + + pci_read_config_byte(dev, 0x50, ®50h); + pci_read_config_byte(dev, 0x52, ®52h); + pci_read_config_byte(dev, 0x5a, ®5ah); + printk("%s: (%s) reg50h=0x%02x, reg52h=0x%02x, reg5ah=0x%02x\n", + drive->name, __FUNCTION__, reg50h, reg52h, reg5ah); + if (reg5ah & 0x10) + pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10); +#if 0 + /* how about we flush and reset, mmmkay? */ + pci_write_config_byte(dev, 0x51, 0x1F); + /* fall through to a reset */ + case dma_start: + case ide_dma_end: + /* reset the chips state over and over.. */ + pci_write_config_byte(dev, 0x51, 0x13); +#endif + return __ide_dma_lostirq(drive); +} + +static void hpt370_clear_engine (ide_drive_t *drive) +{ + u8 regstate = HWIF(drive)->channel ? 0x54 : 0x50; + pci_write_config_byte(HWIF(drive)->pci_dev, regstate, 0x37); + udelay(10); +} + +static void hpt370_ide_dma_start(ide_drive_t *drive) +{ +#ifdef HPT_RESET_STATE_ENGINE + hpt370_clear_engine(drive); +#endif + ide_dma_start(drive); +} + +static int hpt370_ide_dma_end (ide_drive_t *drive) +{ + ide_hwif_t *hwif = HWIF(drive); + u8 dma_stat = hwif->INB(hwif->dma_status); + + if (dma_stat & 0x01) { + /* wait a little */ + udelay(20); + dma_stat = hwif->INB(hwif->dma_status); + } + if ((dma_stat & 0x01) != 0) + /* fallthrough */ + (void) HWIF(drive)->ide_dma_timeout(drive); + + return __ide_dma_end(drive); +} + +static void hpt370_lostirq_timeout (ide_drive_t *drive) +{ + ide_hwif_t *hwif = HWIF(drive); + u8 bfifo = 0, reginfo = hwif->channel ? 0x56 : 0x52; + u8 dma_stat = 0, dma_cmd = 0; + + pci_read_config_byte(HWIF(drive)->pci_dev, reginfo, &bfifo); + printk("%s: %d bytes in FIFO\n", drive->name, bfifo); + hpt370_clear_engine(drive); + /* get dma command mode */ + dma_cmd = hwif->INB(hwif->dma_command); + /* stop dma */ + hwif->OUTB(dma_cmd & ~0x1, hwif->dma_command); + dma_stat = hwif->INB(hwif->dma_status); + /* clear errors */ + hwif->OUTB(dma_stat | 0x6, hwif->dma_status); +} + +static int hpt370_ide_dma_timeout (ide_drive_t *drive) +{ + hpt370_lostirq_timeout(drive); + hpt370_clear_engine(drive); + return __ide_dma_timeout(drive); +} + +static int hpt370_ide_dma_lostirq (ide_drive_t *drive) +{ + hpt370_lostirq_timeout(drive); + hpt370_clear_engine(drive); + return __ide_dma_lostirq(drive); +} + +/* returns 1 if DMA IRQ issued, 0 otherwise */ +static int hpt374_ide_dma_test_irq(ide_drive_t *drive) +{ + ide_hwif_t *hwif = HWIF(drive); + u16 bfifo = 0; + u8 reginfo = hwif->channel ? 0x56 : 0x52; + u8 dma_stat; + + pci_read_config_word(hwif->pci_dev, reginfo, &bfifo); + if (bfifo & 0x1FF) { +// printk("%s: %d bytes in FIFO\n", drive->name, bfifo); + return 0; + } + + dma_stat = hwif->INB(hwif->dma_status); + /* return 1 if INTR asserted */ + if ((dma_stat & 4) == 4) + return 1; + + if (!drive->waiting_for_dma) + printk(KERN_WARNING "%s: (%s) called while not waiting\n", + drive->name, __FUNCTION__); + return 0; +} + +static int hpt374_ide_dma_end (ide_drive_t *drive) +{ + struct pci_dev *dev = HWIF(drive)->pci_dev; + ide_hwif_t *hwif = HWIF(drive); + u8 msc_stat = 0, mscreg = hwif->channel ? 0x54 : 0x50; + u8 bwsr_stat = 0, bwsr_mask = hwif->channel ? 0x02 : 0x01; + + pci_read_config_byte(dev, 0x6a, &bwsr_stat); + pci_read_config_byte(dev, mscreg, &msc_stat); + if ((bwsr_stat & bwsr_mask) == bwsr_mask) + pci_write_config_byte(dev, mscreg, msc_stat|0x30); + return __ide_dma_end(drive); +} + +/** + * hpt372n_set_clock - perform clock switching dance + * @drive: Drive to switch + * @mode: Switching mode (0x21 for write, 0x23 otherwise) + * + * Switch the DPLL clock on the HPT372N devices. This is a + * right mess. + */ + +static void hpt372n_set_clock(ide_drive_t *drive, int mode) +{ + ide_hwif_t *hwif = HWIF(drive); + + /* FIXME: should we check for DMA active and BUG() */ + /* Tristate the bus */ + outb(0x80, hwif->dma_base+0x73); + outb(0x80, hwif->dma_base+0x77); + + /* Switch clock and reset channels */ + outb(mode, hwif->dma_base+0x7B); + outb(0xC0, hwif->dma_base+0x79); + + /* Reset state machines */ + outb(0x37, hwif->dma_base+0x70); + outb(0x37, hwif->dma_base+0x74); + + /* Complete reset */ + outb(0x00, hwif->dma_base+0x79); + + /* Reconnect channels to bus */ + outb(0x00, hwif->dma_base+0x73); + outb(0x00, hwif->dma_base+0x77); +} + +/** + * hpt372n_rw_disk - prepare for I/O + * @drive: drive for command + * @rq: block request structure + * + * This is called when a disk I/O is issued to the 372N. + * We need it because of the clock switching. + */ + +static void hpt372n_rw_disk(ide_drive_t *drive, struct request *rq) +{ + ide_hwif_t *hwif = drive->hwif; + int wantclock; + + wantclock = rq_data_dir(rq) ? 0x23 : 0x21; + + if (hwif->config_data != wantclock) { + hpt372n_set_clock(drive, wantclock); + hwif->config_data = wantclock; + } +} + +/* + * Since SUN Cobalt is attempting to do this operation, I should disclose + * this has been a long time ago Thu Jul 27 16:40:57 2000 was the patch date + * HOTSWAP ATA Infrastructure. + */ + +static void hpt3xx_reset (ide_drive_t *drive) +{ +#if 0 + unsigned long high_16 = pci_resource_start(HWIF(drive)->pci_dev, 4); + u8 reset = (HWIF(drive)->channel) ? 0x80 : 0x40; + u8 reg59h = 0; + + pci_read_config_byte(HWIF(drive)->pci_dev, 0x59, ®59h); + pci_write_config_byte(HWIF(drive)->pci_dev, 0x59, reg59h|reset); + pci_write_config_byte(HWIF(drive)->pci_dev, 0x59, reg59h); +#endif +} + +static int hpt3xx_tristate (ide_drive_t * drive, int state) +{ + ide_hwif_t *hwif = HWIF(drive); + struct pci_dev *dev = hwif->pci_dev; + u8 reg59h = 0, reset = (hwif->channel) ? 0x80 : 0x40; + u8 regXXh = 0, state_reg= (hwif->channel) ? 0x57 : 0x53; + +// hwif->bus_state = state; + + pci_read_config_byte(dev, 0x59, ®59h); + pci_read_config_byte(dev, state_reg, ®XXh); + + if (state) { + (void) ide_do_reset(drive); + pci_write_config_byte(dev, state_reg, regXXh|0x80); + pci_write_config_byte(dev, 0x59, reg59h|reset); + } else { + pci_write_config_byte(dev, 0x59, reg59h & ~(reset)); + pci_write_config_byte(dev, state_reg, regXXh & ~(0x80)); + (void) ide_do_reset(drive); + } + return 0; +} + +/* + * set/get power state for a drive. + * turning the power off does the following things: + * 1) soft-reset the drive + * 2) tri-states the ide bus + * + * when we turn things back on, we need to re-initialize things. + */ +#define TRISTATE_BIT 0x8000 +static int hpt370_busproc(ide_drive_t * drive, int state) +{ + ide_hwif_t *hwif = HWIF(drive); + struct pci_dev *dev = hwif->pci_dev; + u8 tristate = 0, resetmask = 0, bus_reg = 0; + u16 tri_reg; + + hwif->bus_state = state; + + if (hwif->channel) { + /* secondary channel */ + tristate = 0x56; + resetmask = 0x80; + } else { + /* primary channel */ + tristate = 0x52; + resetmask = 0x40; + } + + /* grab status */ + pci_read_config_word(dev, tristate, &tri_reg); + pci_read_config_byte(dev, 0x59, &bus_reg); + + /* set the state. we don't set it if we don't need to do so. + * make sure that the drive knows that it has failed if it's off */ + switch (state) { + case BUSSTATE_ON: + hwif->drives[0].failures = 0; + hwif->drives[1].failures = 0; + if ((bus_reg & resetmask) == 0) + return 0; + tri_reg &= ~TRISTATE_BIT; + bus_reg &= ~resetmask; + break; + case BUSSTATE_OFF: + hwif->drives[0].failures = hwif->drives[0].max_failures + 1; + hwif->drives[1].failures = hwif->drives[1].max_failures + 1; + if ((tri_reg & TRISTATE_BIT) == 0 && (bus_reg & resetmask)) + return 0; + tri_reg &= ~TRISTATE_BIT; + bus_reg |= resetmask; + break; + case BUSSTATE_TRISTATE: + hwif->drives[0].failures = hwif->drives[0].max_failures + 1; + hwif->drives[1].failures = hwif->drives[1].max_failures + 1; + if ((tri_reg & TRISTATE_BIT) && (bus_reg & resetmask)) + return 0; + tri_reg |= TRISTATE_BIT; + bus_reg |= resetmask; + break; + } + pci_write_config_byte(dev, 0x59, bus_reg); + pci_write_config_word(dev, tristate, tri_reg); + + return 0; +} + +static int __devinit init_hpt37x(struct pci_dev *dev) +{ + int adjust, i; + u16 freq; + u32 pll; + u8 reg5bh; + u8 reg5ah = 0; + unsigned long dmabase = pci_resource_start(dev, 4); + u8 did, rid; + int is_372n = 0; + + pci_read_config_byte(dev, 0x5a, ®5ah); + /* interrupt force enable */ + pci_write_config_byte(dev, 0x5a, (reg5ah & ~0x10)); + + if(dmabase) + { + did = inb(dmabase + 0x22); + rid = inb(dmabase + 0x28); + + if((did == 4 && rid == 6) || (did == 5 && rid > 1)) + is_372n = 1; + } + + /* + * default to pci clock. make sure MA15/16 are set to output + * to prevent drives having problems with 40-pin cables. + */ + pci_write_config_byte(dev, 0x5b, 0x23); + + /* + * set up the PLL. we need to adjust it so that it's stable. + * freq = Tpll * 192 / Tpci + * + * Todo. For non x86 should probably check the dword is + * set to 0xABCDExxx indicating the BIOS saved f_CNT + */ + pci_read_config_word(dev, 0x78, &freq); + freq &= 0x1FF; + + /* + * The 372N uses different PCI clock information and has + * some other complications + * On PCI33 timing we must clock switch + * On PCI66 timing we must NOT use the PCI clock + * + * Currently we always set up the PLL for the 372N + */ + + pci_set_drvdata(dev, NULL); + + if(is_372n) + { + printk(KERN_INFO "hpt: HPT372N detected, using 372N timing.\n"); + if(freq < 0x55) + pll = F_LOW_PCI_33; + else if(freq < 0x70) + pll = F_LOW_PCI_40; + else if(freq < 0x7F) + pll = F_LOW_PCI_50; + else + pll = F_LOW_PCI_66; + + printk(KERN_INFO "FREQ: %d PLL: %d\n", freq, pll); + + /* We always use the pll not the PCI clock on 372N */ + } + else + { + if(freq < 0x9C) + pll = F_LOW_PCI_33; + else if(freq < 0xb0) + pll = F_LOW_PCI_40; + else if(freq <0xc8) + pll = F_LOW_PCI_50; + else + pll = F_LOW_PCI_66; + + if (pll == F_LOW_PCI_33) { + if (hpt_minimum_revision(dev,8)) + pci_set_drvdata(dev, (void *) thirty_three_base_hpt374); + else if (hpt_minimum_revision(dev,5)) + pci_set_drvdata(dev, (void *) thirty_three_base_hpt372); + else if (hpt_minimum_revision(dev,4)) + pci_set_drvdata(dev, (void *) thirty_three_base_hpt370a); + else + pci_set_drvdata(dev, (void *) thirty_three_base_hpt370); + printk("HPT37X: using 33MHz PCI clock\n"); + } else if (pll == F_LOW_PCI_40) { + /* Unsupported */ + } else if (pll == F_LOW_PCI_50) { + if (hpt_minimum_revision(dev,8)) + pci_set_drvdata(dev, (void *) fifty_base_hpt370a); + else if (hpt_minimum_revision(dev,5)) + pci_set_drvdata(dev, (void *) fifty_base_hpt372); + else if (hpt_minimum_revision(dev,4)) + pci_set_drvdata(dev, (void *) fifty_base_hpt370a); + else + pci_set_drvdata(dev, (void *) fifty_base_hpt370a); + printk("HPT37X: using 50MHz PCI clock\n"); + } else { + if (hpt_minimum_revision(dev,8)) + { + printk(KERN_ERR "HPT37x: 66MHz timings are not supported.\n"); + } + else if (hpt_minimum_revision(dev,5)) + pci_set_drvdata(dev, (void *) sixty_six_base_hpt372); + else if (hpt_minimum_revision(dev,4)) + pci_set_drvdata(dev, (void *) sixty_six_base_hpt370a); + else + pci_set_drvdata(dev, (void *) sixty_six_base_hpt370); + printk("HPT37X: using 66MHz PCI clock\n"); + } + } + + /* + * only try the pll if we don't have a table for the clock + * speed that we're running at. NOTE: the internal PLL will + * result in slow reads when using a 33MHz PCI clock. we also + * don't like to use the PLL because it will cause glitches + * on PRST/SRST when the HPT state engine gets reset. + */ + if (pci_get_drvdata(dev)) + goto init_hpt37X_done; + + /* + * adjust PLL based upon PCI clock, enable it, and wait for + * stabilization. + */ + adjust = 0; + freq = (pll < F_LOW_PCI_50) ? 2 : 4; + while (adjust++ < 6) { + pci_write_config_dword(dev, 0x5c, (freq + pll) << 16 | + pll | 0x100); + + /* wait for clock stabilization */ + for (i = 0; i < 0x50000; i++) { + pci_read_config_byte(dev, 0x5b, ®5bh); + if (reg5bh & 0x80) { + /* spin looking for the clock to destabilize */ + for (i = 0; i < 0x1000; ++i) { + pci_read_config_byte(dev, 0x5b, + ®5bh); + if ((reg5bh & 0x80) == 0) + goto pll_recal; + } + pci_read_config_dword(dev, 0x5c, &pll); + pci_write_config_dword(dev, 0x5c, + pll & ~0x100); + pci_write_config_byte(dev, 0x5b, 0x21); + if (hpt_minimum_revision(dev,8)) + pci_set_drvdata(dev, (void *) fifty_base_hpt370a); + else if (hpt_minimum_revision(dev,5)) + pci_set_drvdata(dev, (void *) fifty_base_hpt372); + else if (hpt_minimum_revision(dev,4)) + pci_set_drvdata(dev, (void *) fifty_base_hpt370a); + else + pci_set_drvdata(dev, (void *) fifty_base_hpt370a); + printk("HPT37X: using 50MHz internal PLL\n"); + goto init_hpt37X_done; + } + } +pll_recal: + if (adjust & 1) + pll -= (adjust >> 1); + else + pll += (adjust >> 1); + } + +init_hpt37X_done: + /* reset state engine */ + pci_write_config_byte(dev, 0x50, 0x37); + pci_write_config_byte(dev, 0x54, 0x37); + udelay(100); + return 0; +} + +static int __devinit init_hpt366(struct pci_dev *dev) +{ + u32 reg1 = 0; + u8 drive_fast = 0; + + /* + * Disable the "fast interrupt" prediction. + */ + pci_read_config_byte(dev, 0x51, &drive_fast); + if (drive_fast & 0x80) + pci_write_config_byte(dev, 0x51, drive_fast & ~0x80); + pci_read_config_dword(dev, 0x40, ®1); + + /* detect bus speed by looking at control reg timing: */ + switch((reg1 >> 8) & 7) { + case 5: + pci_set_drvdata(dev, (void *) forty_base_hpt366); + break; + case 9: + pci_set_drvdata(dev, (void *) twenty_five_base_hpt366); + break; + case 7: + default: + pci_set_drvdata(dev, (void *) thirty_three_base_hpt366); + break; + } + + if (!pci_get_drvdata(dev)) + { + printk(KERN_ERR "hpt366: unknown bus timing.\n"); + pci_set_drvdata(dev, NULL); + } + return 0; +} + +static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const char *name) +{ + int ret = 0; + u8 test = 0; + + if (dev->resource[PCI_ROM_RESOURCE].start) + pci_write_config_byte(dev, PCI_ROM_ADDRESS, + dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE); + + pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &test); + if (test != (L1_CACHE_BYTES / 4)) + pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, + (L1_CACHE_BYTES / 4)); + + pci_read_config_byte(dev, PCI_LATENCY_TIMER, &test); + if (test != 0x78) + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); + + pci_read_config_byte(dev, PCI_MIN_GNT, &test); + if (test != 0x08) + pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); + + pci_read_config_byte(dev, PCI_MAX_LAT, &test); + if (test != 0x08) + pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); + + if (hpt_minimum_revision(dev, 3)) { + ret = init_hpt37x(dev); + } else { + ret =init_hpt366(dev); + } + if (ret) + return ret; + + return dev->irq; +} + +static void __devinit init_hwif_hpt366(ide_hwif_t *hwif) +{ + struct pci_dev *dev = hwif->pci_dev; + u8 ata66 = 0, regmask = (hwif->channel) ? 0x01 : 0x02; + u8 did, rid; + unsigned long dmabase = hwif->dma_base; + int is_372n = 0; + + if(dmabase) + { + did = inb(dmabase + 0x22); + rid = inb(dmabase + 0x28); + + if((did == 4 && rid == 6) || (did == 5 && rid > 1)) + is_372n = 1; + } + + hwif->tuneproc = &hpt3xx_tune_drive; + hwif->speedproc = &hpt3xx_tune_chipset; + hwif->quirkproc = &hpt3xx_quirkproc; + hwif->intrproc = &hpt3xx_intrproc; + hwif->maskproc = &hpt3xx_maskproc; + + if(is_372n) + hwif->rw_disk = &hpt372n_rw_disk; + + /* + * The HPT37x uses the CBLID pins as outputs for MA15/MA16 + * address lines to access an external eeprom. To read valid + * cable detect state the pins must be enabled as inputs. + */ + if (hpt_minimum_revision(dev, 8) && PCI_FUNC(dev->devfn) & 1) { + /* + * HPT374 PCI function 1 + * - set bit 15 of reg 0x52 to enable TCBLID as input + * - set bit 15 of reg 0x56 to enable FCBLID as input + */ + u16 mcr3, mcr6; + pci_read_config_word(dev, 0x52, &mcr3); + pci_read_config_word(dev, 0x56, &mcr6); + pci_write_config_word(dev, 0x52, mcr3 | 0x8000); + pci_write_config_word(dev, 0x56, mcr6 | 0x8000); + /* now read cable id register */ + pci_read_config_byte(dev, 0x5a, &ata66); + pci_write_config_word(dev, 0x52, mcr3); + pci_write_config_word(dev, 0x56, mcr6); + } else if (hpt_minimum_revision(dev, 3)) { + /* + * HPT370/372 and 374 pcifn 0 + * - clear bit 0 of 0x5b to enable P/SCBLID as inputs + */ + u8 scr2; + pci_read_config_byte(dev, 0x5b, &scr2); + pci_write_config_byte(dev, 0x5b, scr2 & ~1); + /* now read cable id register */ + pci_read_config_byte(dev, 0x5a, &ata66); + pci_write_config_byte(dev, 0x5b, scr2); + } else { + pci_read_config_byte(dev, 0x5a, &ata66); + } + +#ifdef DEBUG + printk("HPT366: reg5ah=0x%02x ATA-%s Cable Port%d\n", + ata66, (ata66 & regmask) ? "33" : "66", + PCI_FUNC(hwif->pci_dev->devfn)); +#endif /* DEBUG */ + +#ifdef HPT_SERIALIZE_IO + /* serialize access to this device */ + if (hwif->mate) + hwif->serialized = hwif->mate->serialized = 1; +#endif + + if (hpt_minimum_revision(dev,3)) { + u8 reg5ah = 0; + pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10); + /* + * set up ioctl for power status. + * note: power affects both + * drives on each channel + */ + hwif->resetproc = &hpt3xx_reset; + hwif->busproc = &hpt370_busproc; +// hwif->drives[0].autotune = hwif->drives[1].autotune = 1; + } else if (hpt_minimum_revision(dev,2)) { + hwif->resetproc = &hpt3xx_reset; + hwif->busproc = &hpt3xx_tristate; + } else { + hwif->resetproc = &hpt3xx_reset; + hwif->busproc = &hpt3xx_tristate; + } + + if (!hwif->dma_base) { + hwif->drives[0].autotune = 1; + hwif->drives[1].autotune = 1; + return; + } + + hwif->ultra_mask = 0x7f; + hwif->mwdma_mask = 0x07; + + if (!(hwif->udma_four)) + hwif->udma_four = ((ata66 & regmask) ? 0 : 1); + hwif->ide_dma_check = &hpt366_config_drive_xfer_rate; + + if (hpt_minimum_revision(dev,8)) { + hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq; + hwif->ide_dma_end = &hpt374_ide_dma_end; + } else if (hpt_minimum_revision(dev,5)) { + hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq; + hwif->ide_dma_end = &hpt374_ide_dma_end; + } else if (hpt_minimum_revision(dev,3)) { + hwif->dma_start = &hpt370_ide_dma_start; + hwif->ide_dma_end = &hpt370_ide_dma_end; + hwif->ide_dma_timeout = &hpt370_ide_dma_timeout; + hwif->ide_dma_lostirq = &hpt370_ide_dma_lostirq; + } else if (hpt_minimum_revision(dev,2)) + hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq; + else + hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq; + + if (!noautodma) + hwif->autodma = 1; + hwif->drives[0].autodma = hwif->autodma; + hwif->drives[1].autodma = hwif->autodma; +} + +static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase) +{ + u8 masterdma = 0, slavedma = 0; + u8 dma_new = 0, dma_old = 0; + u8 primary = hwif->channel ? 0x4b : 0x43; + u8 secondary = hwif->channel ? 0x4f : 0x47; + unsigned long flags; + + if (!dmabase) + return; + + if(pci_get_drvdata(hwif->pci_dev) == NULL) + { + printk(KERN_WARNING "hpt: no known IDE timings, disabling DMA.\n"); + return; + } + + dma_old = hwif->INB(dmabase+2); + + local_irq_save(flags); + + dma_new = dma_old; + pci_read_config_byte(hwif->pci_dev, primary, &masterdma); + pci_read_config_byte(hwif->pci_dev, secondary, &slavedma); + + if (masterdma & 0x30) dma_new |= 0x20; + if (slavedma & 0x30) dma_new |= 0x40; + if (dma_new != dma_old) + hwif->OUTB(dma_new, dmabase+2); + + local_irq_restore(flags); + + ide_setup_dma(hwif, dmabase, 8); +} + +static int __devinit init_setup_hpt374(struct pci_dev *dev, ide_pci_device_t *d) +{ + struct pci_dev *findev = NULL; + + if (PCI_FUNC(dev->devfn) & 1) + return -ENODEV; + + while ((findev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, findev)) != NULL) { + if ((findev->vendor == dev->vendor) && + (findev->device == dev->device) && + ((findev->devfn - dev->devfn) == 1) && + (PCI_FUNC(findev->devfn) & 1)) { + if (findev->irq != dev->irq) { + /* FIXME: we need a core pci_set_interrupt() */ + findev->irq = dev->irq; + printk(KERN_WARNING "%s: pci-config space interrupt " + "fixed.\n", d->name); + } + return ide_setup_pci_devices(dev, findev, d); + } + } + return ide_setup_pci_device(dev, d); +} + +static int __devinit init_setup_hpt37x(struct pci_dev *dev, ide_pci_device_t *d) +{ + return ide_setup_pci_device(dev, d); +} + +static int __devinit init_setup_hpt366(struct pci_dev *dev, ide_pci_device_t *d) +{ + struct pci_dev *findev = NULL; + u8 pin1 = 0, pin2 = 0; + unsigned int class_rev; + char *chipset_names[] = {"HPT366", "HPT366", "HPT368", + "HPT370", "HPT370A", "HPT372", + "HPT372N" }; + + if (PCI_FUNC(dev->devfn) & 1) + return -ENODEV; + + pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); + class_rev &= 0xff; + + if(dev->device == PCI_DEVICE_ID_TTI_HPT372N) + class_rev = 6; + + if(class_rev <= 6) + d->name = chipset_names[class_rev]; + + switch(class_rev) { + case 6: + case 5: + case 4: + case 3: + goto init_single; + default: + break; + } + + d->channels = 1; + + pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1); + while ((findev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, findev)) != NULL) { + if ((findev->vendor == dev->vendor) && + (findev->device == dev->device) && + ((findev->devfn - dev->devfn) == 1) && + (PCI_FUNC(findev->devfn) & 1)) { + pci_read_config_byte(findev, PCI_INTERRUPT_PIN, &pin2); + if ((pin1 != pin2) && (dev->irq == findev->irq)) { + d->bootable = ON_BOARD; + printk("%s: onboard version of chipset, " + "pin1=%d pin2=%d\n", d->name, + pin1, pin2); + } + return ide_setup_pci_devices(dev, findev, d); + } + } +init_single: + return ide_setup_pci_device(dev, d); +} + +static ide_pci_device_t hpt366_chipsets[] __devinitdata = { + { /* 0 */ + .name = "HPT366", + .init_setup = init_setup_hpt366, + .init_chipset = init_chipset_hpt366, + .init_hwif = init_hwif_hpt366, + .init_dma = init_dma_hpt366, + .channels = 2, + .autodma = AUTODMA, + .bootable = OFF_BOARD, + .extra = 240 + },{ /* 1 */ + .name = "HPT372A", + .init_setup = init_setup_hpt37x, + .init_chipset = init_chipset_hpt366, + .init_hwif = init_hwif_hpt366, + .init_dma = init_dma_hpt366, + .channels = 2, + .autodma = AUTODMA, + .bootable = OFF_BOARD, + },{ /* 2 */ + .name = "HPT302", + .init_setup = init_setup_hpt37x, + .init_chipset = init_chipset_hpt366, + .init_hwif = init_hwif_hpt366, + .init_dma = init_dma_hpt366, + .channels = 2, + .autodma = AUTODMA, + .bootable = OFF_BOARD, + },{ /* 3 */ + .name = "HPT371", + .init_setup = init_setup_hpt37x, + .init_chipset = init_chipset_hpt366, + .init_hwif = init_hwif_hpt366, + .init_dma = init_dma_hpt366, + .channels = 2, + .autodma = AUTODMA, + .bootable = OFF_BOARD, + },{ /* 4 */ + .name = "HPT374", + .init_setup = init_setup_hpt374, + .init_chipset = init_chipset_hpt366, + .init_hwif = init_hwif_hpt366, + .init_dma = init_dma_hpt366, + .channels = 2, /* 4 */ + .autodma = AUTODMA, + .bootable = OFF_BOARD, + },{ /* 5 */ + .name = "HPT372N", + .init_setup = init_setup_hpt37x, + .init_chipset = init_chipset_hpt366, + .init_hwif = init_hwif_hpt366, + .init_dma = init_dma_hpt366, + .channels = 2, /* 4 */ + .autodma = AUTODMA, + .bootable = OFF_BOARD, + } +}; + +/** + * hpt366_init_one - called when an HPT366 is found + * @dev: the hpt366 device + * @id: the matching pci id + * + * Called when the PCI registration layer (or the IDE initialization) + * finds a device matching our IDE device tables. + */ + +static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + ide_pci_device_t *d = &hpt366_chipsets[id->driver_data]; + + return d->init_setup(dev, d); +} + +static struct pci_device_id hpt366_pci_tbl[] = { + { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, + { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2}, + { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3}, + { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4}, + { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5}, + { 0, }, +}; +MODULE_DEVICE_TABLE(pci, hpt366_pci_tbl); + +static struct pci_driver driver = { + .name = "HPT366_IDE", + .id_table = hpt366_pci_tbl, + .probe = hpt366_init_one, +}; + +static int hpt366_ide_init(void) +{ + return ide_pci_register_driver(&driver); +} + +module_init(hpt366_ide_init); + +MODULE_AUTHOR("Andre Hedrick"); +MODULE_DESCRIPTION("PCI driver module for Highpoint HPT366 IDE"); +MODULE_LICENSE("GPL"); -- cgit v1.2.2