From 1cf92b453a405f6e452737962933a19ec1582029 Mon Sep 17 00:00:00 2001 From: Jack Stone Date: Mon, 15 Jun 2009 18:01:46 +0200 Subject: i2c: Remove void casts Remove uneeded void casts. Signed-off-by: Jack Stone Signed-off-by: Jean Delvare --- drivers/i2c/i2c-core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index 85e2e919d1cd..dfd7bc8094bf 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -1509,7 +1509,7 @@ struct i2c_adapter* i2c_get_adapter(int id) struct i2c_adapter *adapter; mutex_lock(&core_lock); - adapter = (struct i2c_adapter *)idr_find(&i2c_adapter_idr, id); + adapter = idr_find(&i2c_adapter_idr, id); if (adapter && !try_module_get(adapter->owner)) adapter = NULL; -- cgit v1.2.2 From 66b650f04576a6737579ec404446450026ff2e0b Mon Sep 17 00:00:00 2001 From: Clifford Wolf Date: Mon, 15 Jun 2009 18:01:46 +0200 Subject: i2c: Retry automatically on arbitration loss Some small changes in i2c core to retry i2c xfers until either the maximum number of retries or the timeout is hit. Signed-off-by: Clifford Wolf Signed-off-by: Jean Delvare --- drivers/i2c/i2c-core.c | 30 ++++++++++++++++++++++++++---- 1 file changed, 26 insertions(+), 4 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index dfd7bc8094bf..635c488262c0 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -1022,7 +1022,8 @@ module_exit(i2c_exit); */ int i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) { - int ret; + unsigned long orig_jiffies; + int ret, try; /* REVISIT the fault reporting model here is weak: * @@ -1060,7 +1061,15 @@ int i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) mutex_lock_nested(&adap->bus_lock, adap->level); } - ret = adap->algo->master_xfer(adap,msgs,num); + /* Retry automatically on arbitration loss */ + orig_jiffies = jiffies; + for (ret = 0, try = 0; try <= adap->retries; try++) { + ret = adap->algo->master_xfer(adap, msgs, num); + if (ret != -EAGAIN) + break; + if (time_after(jiffies, orig_jiffies + adap->timeout)) + break; + } mutex_unlock(&adap->bus_lock); return ret; @@ -1995,14 +2004,27 @@ s32 i2c_smbus_xfer(struct i2c_adapter *adapter, u16 addr, unsigned short flags, char read_write, u8 command, int protocol, union i2c_smbus_data *data) { + unsigned long orig_jiffies; + int try; s32 res; flags &= I2C_M_TEN | I2C_CLIENT_PEC; if (adapter->algo->smbus_xfer) { mutex_lock(&adapter->bus_lock); - res = adapter->algo->smbus_xfer(adapter,addr,flags,read_write, - command, protocol, data); + + /* Retry automatically on arbitration loss */ + orig_jiffies = jiffies; + for (res = 0, try = 0; try <= adapter->retries; try++) { + res = adapter->algo->smbus_xfer(adapter, addr, flags, + read_write, command, + protocol, data); + if (res != -EAGAIN) + break; + if (time_after(jiffies, + orig_jiffies + adapter->timeout)) + break; + } mutex_unlock(&adapter->bus_lock); } else res = i2c_smbus_xfer_emulated(adapter,addr,flags,read_write, -- cgit v1.2.2 From fa1b2ca4fa271f9300a764b9d505a027156f749b Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Mon, 15 Jun 2009 18:01:48 +0200 Subject: i2c: Do not probe for TV chips on Voodoo3 adapters There's no point in giving the I2C bus of Voodoo3 adapters a class value, there's no video chip driver checking for it anymore. If support is ever needed, the video device should be instantiated explicitly rather than probed. To the best of my knowledge the only video chip that can be found on these boards is a BT869 video encoder, for which no support exists currently. Signed-off-by: Jean Delvare Acked-by: Krzysztof Helt --- drivers/i2c/busses/i2c-voodoo3.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-voodoo3.c b/drivers/i2c/busses/i2c-voodoo3.c index 1a474acc0ddd..7663d57833a0 100644 --- a/drivers/i2c/busses/i2c-voodoo3.c +++ b/drivers/i2c/busses/i2c-voodoo3.c @@ -163,7 +163,6 @@ static struct i2c_algo_bit_data voo_i2c_bit_data = { static struct i2c_adapter voodoo3_i2c_adapter = { .owner = THIS_MODULE, - .class = I2C_CLASS_TV_ANALOG, .name = "I2C Voodoo3/Banshee adapter", .algo_data = &voo_i2c_bit_data, }; -- cgit v1.2.2 From c52cf01f5b35d77b2a918c319e22567de5c3c15f Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Mon, 15 Jun 2009 18:01:48 +0200 Subject: i2c: Do not give adapters a default parent We don't need to give adapters a parent if they don't have one. The driver core will put them in the virtual device directory and all will be fine. Signed-off-by: Jean Delvare --- drivers/i2c/i2c-core.c | 11 ----------- 1 file changed, 11 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index 635c488262c0..5ed622ee65c3 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -29,7 +29,6 @@ #include #include #include -#include #include #include #include @@ -451,16 +450,6 @@ static int i2c_register_adapter(struct i2c_adapter *adap) mutex_lock(&core_lock); - /* Add the adapter to the driver core. - * If the parent pointer is not set up, - * we add this adapter to the host bus. - */ - if (adap->dev.parent == NULL) { - adap->dev.parent = &platform_bus; - pr_debug("I2C adapter driver [%s] forgot to specify " - "physical device\n", adap->name); - } - /* Set default timeout to 1 second if not already set */ if (adap->timeout == 0) adap->timeout = HZ; -- cgit v1.2.2 From 4b364f230a5ef984818837ec7c2be0884eac191c Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 15 Jun 2009 18:01:49 +0200 Subject: i2c/chips: Move max6875 to drivers/misc/eeprom This driver only reads the user EEPROM of that chip, so we can move it to the eeprom-directory in order to further clean up (and later remove) drivers/i2c/chips. The Kconfig text was updated to match the current functionality, dropping the meanwhile obsoleted parts. Defconfigs have been adapted. Signed-off-by: Wolfram Sang Acked-by: Ben Gardner Signed-off-by: Jean Delvare --- drivers/i2c/chips/Kconfig | 15 --- drivers/i2c/chips/Makefile | 1 - drivers/i2c/chips/max6875.c | 246 -------------------------------------------- 3 files changed, 262 deletions(-) delete mode 100644 drivers/i2c/chips/max6875.c (limited to 'drivers/i2c') diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index 8f8c81eb0aee..02d746c9c474 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -64,21 +64,6 @@ config SENSORS_PCA9539 This driver is deprecated and will be dropped soon. Use drivers/gpio/pca953x.c instead. -config SENSORS_MAX6875 - tristate "Maxim MAX6875 Power supply supervisor" - depends on EXPERIMENTAL - help - If you say yes here you get support for the Maxim MAX6875 - EEPROM-programmable, quad power-supply sequencer/supervisor. - - This provides an interface to program the EEPROM and reset the chip. - - This driver also supports the Maxim MAX6874 hex power-supply - sequencer/supervisor if found at a compatible address. - - This driver can also be built as a module. If so, the module - will be called max6875. - config SENSORS_TSL2550 tristate "Taos TSL2550 ambient light sensor" depends on EXPERIMENTAL diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile index 55a376037183..f4680d16ee34 100644 --- a/drivers/i2c/chips/Makefile +++ b/drivers/i2c/chips/Makefile @@ -11,7 +11,6 @@ # obj-$(CONFIG_DS1682) += ds1682.o -obj-$(CONFIG_SENSORS_MAX6875) += max6875.o obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o obj-$(CONFIG_PCF8575) += pcf8575.o diff --git a/drivers/i2c/chips/max6875.c b/drivers/i2c/chips/max6875.c deleted file mode 100644 index 033d9d81ec8a..000000000000 --- a/drivers/i2c/chips/max6875.c +++ /dev/null @@ -1,246 +0,0 @@ -/* - max6875.c - driver for MAX6874/MAX6875 - - Copyright (C) 2005 Ben Gardner - - Based on i2c/chips/eeprom.c - - The MAX6875 has a bank of registers and two banks of EEPROM. - Address ranges are defined as follows: - * 0x0000 - 0x0046 = configuration registers - * 0x8000 - 0x8046 = configuration EEPROM - * 0x8100 - 0x82FF = user EEPROM - - This driver makes the user EEPROM available for read. - - The registers & config EEPROM should be accessed via i2c-dev. - - The MAX6875 ignores the lowest address bit, so each chip responds to - two addresses - 0x50/0x51 and 0x52/0x53. - - Note that the MAX6875 uses i2c_smbus_write_byte_data() to set the read - address, so this driver is destructive if loaded for the wrong EEPROM chip. - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; version 2 of the License. -*/ - -#include -#include -#include -#include -#include -#include - -/* Do not scan - the MAX6875 access method will write to some EEPROM chips */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_1(max6875); - -/* The MAX6875 can only read/write 16 bytes at a time */ -#define SLICE_SIZE 16 -#define SLICE_BITS 4 - -/* USER EEPROM is at addresses 0x8100 - 0x82FF */ -#define USER_EEPROM_BASE 0x8100 -#define USER_EEPROM_SIZE 0x0200 -#define USER_EEPROM_SLICES 32 - -/* MAX6875 commands */ -#define MAX6875_CMD_BLK_READ 0x84 - -/* Each client has this additional data */ -struct max6875_data { - struct i2c_client *fake_client; - struct mutex update_lock; - - u32 valid; - u8 data[USER_EEPROM_SIZE]; - unsigned long last_updated[USER_EEPROM_SLICES]; -}; - -static void max6875_update_slice(struct i2c_client *client, int slice) -{ - struct max6875_data *data = i2c_get_clientdata(client); - int i, j, addr; - u8 *buf; - - if (slice >= USER_EEPROM_SLICES) - return; - - mutex_lock(&data->update_lock); - - buf = &data->data[slice << SLICE_BITS]; - - if (!(data->valid & (1 << slice)) || - time_after(jiffies, data->last_updated[slice])) { - - dev_dbg(&client->dev, "Starting update of slice %u\n", slice); - - data->valid &= ~(1 << slice); - - addr = USER_EEPROM_BASE + (slice << SLICE_BITS); - - /* select the eeprom address */ - if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) { - dev_err(&client->dev, "address set failed\n"); - goto exit_up; - } - - if (i2c_check_functionality(client->adapter, - I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { - if (i2c_smbus_read_i2c_block_data(client, - MAX6875_CMD_BLK_READ, - SLICE_SIZE, - buf) != SLICE_SIZE) { - goto exit_up; - } - } else { - for (i = 0; i < SLICE_SIZE; i++) { - j = i2c_smbus_read_byte(client); - if (j < 0) { - goto exit_up; - } - buf[i] = j; - } - } - data->last_updated[slice] = jiffies; - data->valid |= (1 << slice); - } -exit_up: - mutex_unlock(&data->update_lock); -} - -static ssize_t max6875_read(struct kobject *kobj, - struct bin_attribute *bin_attr, - char *buf, loff_t off, size_t count) -{ - struct i2c_client *client = kobj_to_i2c_client(kobj); - struct max6875_data *data = i2c_get_clientdata(client); - int slice, max_slice; - - if (off > USER_EEPROM_SIZE) - return 0; - - if (off + count > USER_EEPROM_SIZE) - count = USER_EEPROM_SIZE - off; - - /* refresh slices which contain requested bytes */ - max_slice = (off + count - 1) >> SLICE_BITS; - for (slice = (off >> SLICE_BITS); slice <= max_slice; slice++) - max6875_update_slice(client, slice); - - memcpy(buf, &data->data[off], count); - - return count; -} - -static struct bin_attribute user_eeprom_attr = { - .attr = { - .name = "eeprom", - .mode = S_IRUGO, - }, - .size = USER_EEPROM_SIZE, - .read = max6875_read, -}; - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int max6875_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA - | I2C_FUNC_SMBUS_READ_BYTE)) - return -ENODEV; - - /* Only check even addresses */ - if (client->addr & 1) - return -ENODEV; - - strlcpy(info->type, "max6875", I2C_NAME_SIZE); - - return 0; -} - -static int max6875_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - struct max6875_data *data; - int err; - - if (!(data = kzalloc(sizeof(struct max6875_data), GFP_KERNEL))) - return -ENOMEM; - - /* A fake client is created on the odd address */ - data->fake_client = i2c_new_dummy(client->adapter, client->addr + 1); - if (!data->fake_client) { - err = -ENOMEM; - goto exit_kfree; - } - - /* Init real i2c_client */ - i2c_set_clientdata(client, data); - mutex_init(&data->update_lock); - - err = sysfs_create_bin_file(&client->dev.kobj, &user_eeprom_attr); - if (err) - goto exit_remove_fake; - - return 0; - -exit_remove_fake: - i2c_unregister_device(data->fake_client); -exit_kfree: - kfree(data); - return err; -} - -static int max6875_remove(struct i2c_client *client) -{ - struct max6875_data *data = i2c_get_clientdata(client); - - i2c_unregister_device(data->fake_client); - - sysfs_remove_bin_file(&client->dev.kobj, &user_eeprom_attr); - kfree(data); - - return 0; -} - -static const struct i2c_device_id max6875_id[] = { - { "max6875", 0 }, - { } -}; - -static struct i2c_driver max6875_driver = { - .driver = { - .name = "max6875", - }, - .probe = max6875_probe, - .remove = max6875_remove, - .id_table = max6875_id, - - .detect = max6875_detect, - .address_data = &addr_data, -}; - -static int __init max6875_init(void) -{ - return i2c_add_driver(&max6875_driver); -} - -static void __exit max6875_exit(void) -{ - i2c_del_driver(&max6875_driver); -} - - -MODULE_AUTHOR("Ben Gardner "); -MODULE_DESCRIPTION("MAX6875 driver"); -MODULE_LICENSE("GPL"); - -module_init(max6875_init); -module_exit(max6875_exit); -- cgit v1.2.2 From a231591f0427cfb91ae247be974a7fa0e6b37389 Mon Sep 17 00:00:00 2001 From: Harald Welte Date: Mon, 15 Jun 2009 18:01:49 +0200 Subject: i2c-viapro: Add new PCI device ID for VX855 The south bridge of the VIA VX855 chipset has a different PCI Device ID so i2c-viapro.c needs to be updated with this. Signed-off-by: Harald Welte Signed-off-by: Jean Delvare --- drivers/i2c/busses/Kconfig | 6 +++--- drivers/i2c/busses/i2c-viapro.c | 4 ++++ 2 files changed, 7 insertions(+), 3 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index c8460fa9cfac..0d04d3ebfc2d 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -211,7 +211,7 @@ config I2C_VIA will be called i2c-via. config I2C_VIAPRO - tristate "VIA VT82C596/82C686/82xx and CX700/VX800/VX820" + tristate "VIA VT82C596/82C686/82xx and CX700/VX8xx" depends on PCI help If you say yes to this option, support will be included for the VIA @@ -225,8 +225,8 @@ config I2C_VIAPRO VT8237R/A/S VT8251 CX700 - VX800 - VX820 + VX800/VX820 + VX855/VX875 This driver can also be built as a module. If so, the module will be called i2c-viapro. diff --git a/drivers/i2c/busses/i2c-viapro.c b/drivers/i2c/busses/i2c-viapro.c index 02e6f724b05f..54d810a4d00f 100644 --- a/drivers/i2c/busses/i2c-viapro.c +++ b/drivers/i2c/busses/i2c-viapro.c @@ -37,6 +37,7 @@ VT8251 0x3287 yes CX700 0x8324 yes VX800/VX820 0x8353 yes + VX855/VX875 0x8409 yes Note: we assume there can only be one device, with one SMBus interface. */ @@ -404,6 +405,7 @@ found: switch (pdev->device) { case PCI_DEVICE_ID_VIA_CX700: case PCI_DEVICE_ID_VIA_VX800: + case PCI_DEVICE_ID_VIA_VX855: case PCI_DEVICE_ID_VIA_8251: case PCI_DEVICE_ID_VIA_8237: case PCI_DEVICE_ID_VIA_8237A: @@ -469,6 +471,8 @@ static struct pci_device_id vt596_ids[] = { .driver_data = SMBBA3 }, { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VX800), .driver_data = SMBBA3 }, + { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VX855), + .driver_data = SMBBA3 }, { 0, } }; -- cgit v1.2.2