From a7aea373b4ca428f1be2c1fedd2f26c8e3f2864d Mon Sep 17 00:00:00 2001 From: "Ira W. Snyder" Date: Thu, 23 Apr 2009 16:17:54 -0700 Subject: fsldma: use PCI Read Multiple command By default, the Freescale 83xx DMA controller uses the PCI Read Line command when reading data over the PCI bus. Setting the controller to use the PCI Read Multiple command instead allows the controller to read much larger bursts of data, which provides a drastic speed increase. The slowdown due to using PCI Read Line was only observed when a PCI-to-PCI bridge was between the devices trying to communicate. A simple test driver showed an increase from 4MB/sec to 116MB/sec when performing DMA over the PCI bus. Using DMA to transfer between blocks of local SDRAM showed no change in performance with this patch. The dmatest driver was also used to verify the correctness of the transfers, and showed no errors. Signed-off-by: Ira W. Snyder Acked-by: Timur Tabi Acked-by: Kumar Gala Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 10 ++++++++-- drivers/dma/fsldma.h | 1 + 2 files changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers/dma') diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index f18d1bde0439..a1cb25e277b5 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -12,6 +12,11 @@ * also fit for MPC8560, MPC8555, MPC8548, MPC8641, and etc. * The support for MPC8349 DMA contorller is also added. * + * This driver instructs the DMA controller to issue the PCI Read Multiple + * command for PCI read operations, instead of using the default PCI Read Line + * command. Please be aware that this setting may result in read pre-fetching + * on some platforms. + * * This is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -49,9 +54,10 @@ static void dma_init(struct fsl_dma_chan *fsl_chan) case FSL_DMA_IP_83XX: /* Set the channel to below modes: * EOTIE - End-of-transfer interrupt enable + * PRC_RM - PCI read multiple */ - DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, FSL_DMA_MR_EOTIE, - 32); + DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, FSL_DMA_MR_EOTIE + | FSL_DMA_MR_PRC_RM, 32); break; } diff --git a/drivers/dma/fsldma.h b/drivers/dma/fsldma.h index 4f21a512d848..dc7f26865797 100644 --- a/drivers/dma/fsldma.h +++ b/drivers/dma/fsldma.h @@ -38,6 +38,7 @@ /* Special MR definition for MPC8349 */ #define FSL_DMA_MR_EOTIE 0x00000080 +#define FSL_DMA_MR_PRC_RM 0x00000800 #define FSL_DMA_SR_CH 0x00000020 #define FSL_DMA_SR_PE 0x00000010 -- cgit v1.2.2 From be30b226f2ae618cd719e40267d9923db1db9001 Mon Sep 17 00:00:00 2001 From: Ira Snyder Date: Thu, 28 May 2009 09:20:42 +0000 Subject: fsldma: enable external start for the 83xx controller The 83xx controller has external start capability, but lacks external pause capability. Hook up the external start function pointer for the 83xx controller. Signed-off-by: Ira W. Snyder Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/dma') diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index a1cb25e277b5..10bcf0cb0efc 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -877,9 +877,9 @@ static int __devinit fsl_dma_chan_probe(struct fsl_dma_device *fdev, switch (new_fsl_chan->feature & FSL_DMA_IP_MASK) { case FSL_DMA_IP_85XX: - new_fsl_chan->toggle_ext_start = fsl_chan_toggle_ext_start; new_fsl_chan->toggle_ext_pause = fsl_chan_toggle_ext_pause; case FSL_DMA_IP_83XX: + new_fsl_chan->toggle_ext_start = fsl_chan_toggle_ext_start; new_fsl_chan->set_src_loop_size = fsl_chan_set_src_loop_size; new_fsl_chan->set_dest_loop_size = fsl_chan_set_dest_loop_size; } -- cgit v1.2.2 From 43a1a3ed6bf5a1b9ae197b4f5f20033baf19db61 Mon Sep 17 00:00:00 2001 From: Ira Snyder Date: Thu, 28 May 2009 09:26:40 +0000 Subject: fsldma: do not clear bandwidth control bits on the 83xx controller The 83xx controller does not support the external pause feature. The bit in the mode register that controls external pause on the 85xx controller happens to be part of the bandwidth control settings for the 83xx controller. This patch fixes the driver so that it only clears the external pause bit if the hardware is the 85xx controller. When driving the 83xx controller, the bit is left untouched. This follows the existing convention that mode registers settings are not touched unless necessary. Signed-off-by: Ira W. Snyder Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/dma') diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index 10bcf0cb0efc..6e60c77a145c 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -147,10 +147,11 @@ static void dma_start(struct fsl_dma_chan *fsl_chan) if (fsl_chan->feature & FSL_DMA_CHAN_PAUSE_EXT) { DMA_OUT(fsl_chan, &fsl_chan->reg_base->bcr, 0, 32); mr_set |= FSL_DMA_MR_EMP_EN; - } else + } else if ((fsl_chan->feature & FSL_DMA_IP_MASK) == FSL_DMA_IP_85XX) { DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32) & ~FSL_DMA_MR_EMP_EN, 32); + } if (fsl_chan->feature & FSL_DMA_CHAN_START_EXT) mr_set |= FSL_DMA_MR_EMS_EN; -- cgit v1.2.2 From daf4219dbcbb2efcd638fcd3c29a622e1c18cc38 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Wed, 1 Jul 2009 16:12:53 -0700 Subject: dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA On HIGHMEM64G systems dma_addr_t is known to be larger than (void *) which precludes async_xor from performing dma address conversions by reusing the input parameter address list. However, other parts of the dmaengine infrastructure do not suffer this constraint, so the HIGHMEM64G restriction can be down-levelled. Signed-off-by: Dan Williams --- drivers/dma/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/dma') diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig index 3b3c01b6f1ee..babf214a509b 100644 --- a/drivers/dma/Kconfig +++ b/drivers/dma/Kconfig @@ -4,7 +4,7 @@ menuconfig DMADEVICES bool "DMA Engine support" - depends on !HIGHMEM64G && HAS_DMA + depends on HAS_DMA help DMA engines can do asynchronous data transfers without involving the host CPU. Currently, this framework can be @@ -100,7 +100,7 @@ config NET_DMA config ASYNC_TX_DMA bool "Async_tx: Offload support for the async_tx api" - depends on DMA_ENGINE + depends on DMA_ENGINE && !HIGHMEM64G help This allows the async_tx api to take advantage of offload engines for memcpy, memset, xor, and raid6 p+q operations. If your platform has -- cgit v1.2.2 From e3d433040ee6077e33d4ad22e2f60a38b085786d Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Sun, 28 Jun 2009 09:26:20 -0700 Subject: drivers/dma/fsldma.c: Remove unnecessary semicolons Signed-off-by: Joe Perches Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/dma') diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index 6e60c77a145c..ef87a8984145 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -142,7 +142,7 @@ static int dma_is_idle(struct fsl_dma_chan *fsl_chan) static void dma_start(struct fsl_dma_chan *fsl_chan) { - u32 mr_set = 0;; + u32 mr_set = 0; if (fsl_chan->feature & FSL_DMA_CHAN_PAUSE_EXT) { DMA_OUT(fsl_chan, &fsl_chan->reg_base->bcr, 0, 32); -- cgit v1.2.2 From c019894efc9c9ba5939948caa78c133b1ec8ae63 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Sun, 28 Jun 2009 09:26:21 -0700 Subject: drivers/dma: Remove unnecessary semicolons Signed-off-by: Joe Perches Signed-off-by: Dan Williams --- drivers/dma/dmatest.c | 2 +- drivers/dma/mv_xor.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/dma') diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c index fb7da5141e96..cec1ec0b7d00 100644 --- a/drivers/dma/dmatest.c +++ b/drivers/dma/dmatest.c @@ -114,7 +114,7 @@ static void dmatest_init_srcs(u8 **bufs, unsigned int start, unsigned int len) buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK); for ( ; i < start + len; i++) buf[i] = PATTERN_SRC | PATTERN_COPY - | (~i & PATTERN_COUNT_MASK);; + | (~i & PATTERN_COUNT_MASK); for ( ; i < test_buf_size; i++) buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK); buf++; diff --git a/drivers/dma/mv_xor.c b/drivers/dma/mv_xor.c index ddab94f51224..3f23eabe09f2 100644 --- a/drivers/dma/mv_xor.c +++ b/drivers/dma/mv_xor.c @@ -1176,7 +1176,7 @@ static int __devinit mv_xor_probe(struct platform_device *pdev) if (dma_has_cap(DMA_MEMSET, dma_dev->cap_mask)) dma_dev->device_prep_dma_memset = mv_xor_prep_dma_memset; if (dma_has_cap(DMA_XOR, dma_dev->cap_mask)) { - dma_dev->max_xor = 8; ; + dma_dev->max_xor = 8; dma_dev->device_prep_dma_xor = mv_xor_prep_dma_xor; } -- cgit v1.2.2 From 0a2ff57d6fba92842272889b4bca447344cd9d36 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 3 Jul 2009 19:26:51 +0200 Subject: dmaengine: dmatest: add a maximum number of test iterations The dmatest usually waits for the killing of its kthreads to stop running tests. This patch adds a parameter that sets a maximum number of test iterations. This feature is quite interesting for debugging when you set a lot of traces in your dmaengine controller driver. Signed-off-by: Nicolas Ferre Cc: Haavard Skinnemoen Acked-by: Maciej Sosnowski Signed-off-by: Andrew Morton Signed-off-by: Dan Williams --- drivers/dma/dmatest.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) (limited to 'drivers/dma') diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c index cec1ec0b7d00..2d973d60e7b9 100644 --- a/drivers/dma/dmatest.c +++ b/drivers/dma/dmatest.c @@ -38,6 +38,11 @@ module_param(max_channels, uint, S_IRUGO); MODULE_PARM_DESC(max_channels, "Maximum number of channels to use (default: all)"); +static unsigned int iterations; +module_param(iterations, uint, S_IRUGO); +MODULE_PARM_DESC(iterations, + "Iterations before stopping test (default: infinite)"); + static unsigned int xor_sources = 3; module_param(xor_sources, uint, S_IRUGO); MODULE_PARM_DESC(xor_sources, @@ -270,7 +275,8 @@ static int dmatest_func(void *data) flags = DMA_CTRL_ACK | DMA_COMPL_SKIP_DEST_UNMAP | DMA_PREP_INTERRUPT; - while (!kthread_should_stop()) { + while (!kthread_should_stop() + && !(iterations && total_tests >= iterations)) { struct dma_device *dev = chan->device; struct dma_async_tx_descriptor *tx = NULL; dma_addr_t dma_srcs[src_cnt]; @@ -416,6 +422,13 @@ err_srcbuf: err_srcs: pr_notice("%s: terminating after %u tests, %u failures (status %d)\n", thread_name, total_tests, failed_tests, ret); + + if (iterations > 0) + while (!kthread_should_stop()) { + DECLARE_WAIT_QUEUE_HEAD(wait_dmatest_exit); + interruptible_sleep_on(&wait_dmatest_exit); + } + return ret; } -- cgit v1.2.2 From f1aef8b6e6abf32a3a269542f95a19e2cb319f6c Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Mon, 6 Jul 2009 18:19:44 +0200 Subject: dmaengine: dmatest: correct thread_count while using multiple thread per channel It seems that thread_count is not properly calculated in dmatest. In fact the thread count number that is returned from dmatest_add_threads() is not correctly added to the thread_count and thus not properly printed. Signed-off-by: Nicolas Ferre Acked-by: Haavard Skinnemoen Acked-by: Maciej Sosnowski Signed-off-by: Andrew Morton Signed-off-by: Dan Williams --- drivers/dma/dmatest.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/dma') diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c index 2d973d60e7b9..d93017fc7872 100644 --- a/drivers/dma/dmatest.c +++ b/drivers/dma/dmatest.c @@ -508,11 +508,11 @@ static int dmatest_add_channel(struct dma_chan *chan) if (dma_has_cap(DMA_MEMCPY, dma_dev->cap_mask)) { cnt = dmatest_add_threads(dtc, DMA_MEMCPY); - thread_count += cnt > 0 ?: 0; + thread_count += cnt > 0 ? cnt : 0; } if (dma_has_cap(DMA_XOR, dma_dev->cap_mask)) { cnt = dmatest_add_threads(dtc, DMA_XOR); - thread_count += cnt > 0 ?: 0; + thread_count += cnt > 0 ? cnt : 0; } pr_info("dmatest: Started %u threads using %s\n", -- cgit v1.2.2 From dc78baa2b90b289590911b40b6800f77d0dc935a Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 3 Jul 2009 19:24:33 +0200 Subject: dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on at91sam9rl chip. It will be used on other products in the future. This first release covers only the memory-to-memory tranfer type. This is the only tranfer type supported by this chip. On other products, it will be used also for peripheral DMA transfer (slave API support to come). I used dmatest client without problem in different configurations to test it. Full documentation for this controller can be found in the SAM9RL datasheet: http://www.atmel.com/dyn/products/product_card.asp?part_id=4243 Signed-off-by: Nicolas Ferre Acked-by: Maciej Sosnowski Signed-off-by: Dan Williams --- drivers/dma/Kconfig | 8 + drivers/dma/Makefile | 1 + drivers/dma/at_hdmac.c | 1009 +++++++++++++++++++++++++++++++++++++++++++ drivers/dma/at_hdmac_regs.h | 386 +++++++++++++++++ 4 files changed, 1404 insertions(+) create mode 100644 drivers/dma/at_hdmac.c create mode 100644 drivers/dma/at_hdmac_regs.h (limited to 'drivers/dma') diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig index babf214a509b..bc8fb41cd623 100644 --- a/drivers/dma/Kconfig +++ b/drivers/dma/Kconfig @@ -46,6 +46,14 @@ config DW_DMAC Support the Synopsys DesignWare AHB DMA controller. This can be integrated in chips such as the Atmel AT32ap7000. +config AT_HDMAC + tristate "Atmel AHB DMA support" + depends on ARCH_AT91SAM9RL + select DMA_ENGINE + help + Support the Atmel AHB DMA controller. This can be integrated in + chips such as the Atmel AT91SAM9RL. + config FSL_DMA tristate "Freescale Elo and Elo Plus DMA support" depends on FSL_SOC diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile index 2e5dc96700d2..d7bc5fd17d84 100644 --- a/drivers/dma/Makefile +++ b/drivers/dma/Makefile @@ -7,4 +7,5 @@ obj-$(CONFIG_INTEL_IOP_ADMA) += iop-adma.o obj-$(CONFIG_FSL_DMA) += fsldma.o obj-$(CONFIG_MV_XOR) += mv_xor.o obj-$(CONFIG_DW_DMAC) += dw_dmac.o +obj-$(CONFIG_AT_HDMAC) += at_hdmac.o obj-$(CONFIG_MX3_IPU) += ipu/ diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c new file mode 100644 index 000000000000..64dbf0ce128e --- /dev/null +++ b/drivers/dma/at_hdmac.c @@ -0,0 +1,1009 @@ +/* + * Driver for the Atmel AHB DMA Controller (aka HDMA or DMAC on AT91 systems) + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * + * This supports the Atmel AHB DMA Controller, + * + * The driver has currently been tested with the Atmel AT91SAM9RL + * and AT91SAM9G45 series. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "at_hdmac_regs.h" + +/* + * Glossary + * -------- + * + * at_hdmac : Name of the ATmel AHB DMA Controller + * at_dma_ / atdma : ATmel DMA controller entity related + * atc_ / atchan : ATmel DMA Channel entity related + */ + +#define ATC_DEFAULT_CFG (ATC_FIFOCFG_HALFFIFO) +#define ATC_DEFAULT_CTRLA (0) +#define ATC_DEFAULT_CTRLB (ATC_SIF(0) \ + |ATC_DIF(1)) + +/* + * Initial number of descriptors to allocate for each channel. This could + * be increased during dma usage. + */ +static unsigned int init_nr_desc_per_channel = 64; +module_param(init_nr_desc_per_channel, uint, 0644); +MODULE_PARM_DESC(init_nr_desc_per_channel, + "initial descriptors per channel (default: 64)"); + + +/* prototypes */ +static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx); + + +/*----------------------------------------------------------------------*/ + +static struct at_desc *atc_first_active(struct at_dma_chan *atchan) +{ + return list_first_entry(&atchan->active_list, + struct at_desc, desc_node); +} + +static struct at_desc *atc_first_queued(struct at_dma_chan *atchan) +{ + return list_first_entry(&atchan->queue, + struct at_desc, desc_node); +} + +/** + * atc_alloc_descriptor - allocate and return an initilized descriptor + * @chan: the channel to allocate descriptors for + * @gfp_flags: GFP allocation flags + * + * Note: The ack-bit is positioned in the descriptor flag at creation time + * to make initial allocation more convenient. This bit will be cleared + * and control will be given to client at usage time (during + * preparation functions). + */ +static struct at_desc *atc_alloc_descriptor(struct dma_chan *chan, + gfp_t gfp_flags) +{ + struct at_desc *desc = NULL; + struct at_dma *atdma = to_at_dma(chan->device); + dma_addr_t phys; + + desc = dma_pool_alloc(atdma->dma_desc_pool, gfp_flags, &phys); + if (desc) { + memset(desc, 0, sizeof(struct at_desc)); + dma_async_tx_descriptor_init(&desc->txd, chan); + /* txd.flags will be overwritten in prep functions */ + desc->txd.flags = DMA_CTRL_ACK; + desc->txd.tx_submit = atc_tx_submit; + desc->txd.phys = phys; + } + + return desc; +} + +/** + * atc_desc_get - get a unsused descriptor from free_list + * @atchan: channel we want a new descriptor for + */ +static struct at_desc *atc_desc_get(struct at_dma_chan *atchan) +{ + struct at_desc *desc, *_desc; + struct at_desc *ret = NULL; + unsigned int i = 0; + LIST_HEAD(tmp_list); + + spin_lock_bh(&atchan->lock); + list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) { + i++; + if (async_tx_test_ack(&desc->txd)) { + list_del(&desc->desc_node); + ret = desc; + break; + } + dev_dbg(chan2dev(&atchan->chan_common), + "desc %p not ACKed\n", desc); + } + spin_unlock_bh(&atchan->lock); + dev_vdbg(chan2dev(&atchan->chan_common), + "scanned %u descriptors on freelist\n", i); + + /* no more descriptor available in initial pool: create one more */ + if (!ret) { + ret = atc_alloc_descriptor(&atchan->chan_common, GFP_ATOMIC); + if (ret) { + spin_lock_bh(&atchan->lock); + atchan->descs_allocated++; + spin_unlock_bh(&atchan->lock); + } else { + dev_err(chan2dev(&atchan->chan_common), + "not enough descriptors available\n"); + } + } + + return ret; +} + +/** + * atc_desc_put - move a descriptor, including any children, to the free list + * @atchan: channel we work on + * @desc: descriptor, at the head of a chain, to move to free list + */ +static void atc_desc_put(struct at_dma_chan *atchan, struct at_desc *desc) +{ + if (desc) { + struct at_desc *child; + + spin_lock_bh(&atchan->lock); + list_for_each_entry(child, &desc->txd.tx_list, desc_node) + dev_vdbg(chan2dev(&atchan->chan_common), + "moving child desc %p to freelist\n", + child); + list_splice_init(&desc->txd.tx_list, &atchan->free_list); + dev_vdbg(chan2dev(&atchan->chan_common), + "moving desc %p to freelist\n", desc); + list_add(&desc->desc_node, &atchan->free_list); + spin_unlock_bh(&atchan->lock); + } +} + +/** + * atc_assign_cookie - compute and assign new cookie + * @atchan: channel we work on + * @desc: descriptor to asign cookie for + * + * Called with atchan->lock held and bh disabled + */ +static dma_cookie_t +atc_assign_cookie(struct at_dma_chan *atchan, struct at_desc *desc) +{ + dma_cookie_t cookie = atchan->chan_common.cookie; + + if (++cookie < 0) + cookie = 1; + + atchan->chan_common.cookie = cookie; + desc->txd.cookie = cookie; + + return cookie; +} + +/** + * atc_dostart - starts the DMA engine for real + * @atchan: the channel we want to start + * @first: first descriptor in the list we want to begin with + * + * Called with atchan->lock held and bh disabled + */ +static void atc_dostart(struct at_dma_chan *atchan, struct at_desc *first) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + + /* ASSERT: channel is idle */ + if (atc_chan_is_enabled(atchan)) { + dev_err(chan2dev(&atchan->chan_common), + "BUG: Attempted to start non-idle channel\n"); + dev_err(chan2dev(&atchan->chan_common), + " channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + channel_readl(atchan, SADDR), + channel_readl(atchan, DADDR), + channel_readl(atchan, CTRLA), + channel_readl(atchan, CTRLB), + channel_readl(atchan, DSCR)); + + /* The tasklet will hopefully advance the queue... */ + return; + } + + vdbg_dump_regs(atchan); + + /* clear any pending interrupt */ + while (dma_readl(atdma, EBCISR)) + cpu_relax(); + + channel_writel(atchan, SADDR, 0); + channel_writel(atchan, DADDR, 0); + channel_writel(atchan, CTRLA, 0); + channel_writel(atchan, CTRLB, 0); + channel_writel(atchan, DSCR, first->txd.phys); + dma_writel(atdma, CHER, atchan->mask); + + vdbg_dump_regs(atchan); +} + +/** + * atc_chain_complete - finish work for one transaction chain + * @atchan: channel we work on + * @desc: descriptor at the head of the chain we want do complete + * + * Called with atchan->lock held and bh disabled */ +static void +atc_chain_complete(struct at_dma_chan *atchan, struct at_desc *desc) +{ + dma_async_tx_callback callback; + void *param; + struct dma_async_tx_descriptor *txd = &desc->txd; + + dev_vdbg(chan2dev(&atchan->chan_common), + "descriptor %u complete\n", txd->cookie); + + atchan->completed_cookie = txd->cookie; + callback = txd->callback; + param = txd->callback_param; + + /* move children to free_list */ + list_splice_init(&txd->tx_list, &atchan->free_list); + /* move myself to free_list */ + list_move(&desc->desc_node, &atchan->free_list); + + /* unmap dma addresses */ + if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP)) { + if (txd->flags & DMA_COMPL_DEST_UNMAP_SINGLE) + dma_unmap_single(chan2parent(&atchan->chan_common), + desc->lli.daddr, + desc->len, DMA_FROM_DEVICE); + else + dma_unmap_page(chan2parent(&atchan->chan_common), + desc->lli.daddr, + desc->len, DMA_FROM_DEVICE); + } + if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP)) { + if (txd->flags & DMA_COMPL_SRC_UNMAP_SINGLE) + dma_unmap_single(chan2parent(&atchan->chan_common), + desc->lli.saddr, + desc->len, DMA_TO_DEVICE); + else + dma_unmap_page(chan2parent(&atchan->chan_common), + desc->lli.saddr, + desc->len, DMA_TO_DEVICE); + } + + /* + * The API requires that no submissions are done from a + * callback, so we don't need to drop the lock here + */ + if (callback) + callback(param); + + dma_run_dependencies(txd); +} + +/** + * atc_complete_all - finish work for all transactions + * @atchan: channel to complete transactions for + * + * Eventually submit queued descriptors if any + * + * Assume channel is idle while calling this function + * Called with atchan->lock held and bh disabled + */ +static void atc_complete_all(struct at_dma_chan *atchan) +{ + struct at_desc *desc, *_desc; + LIST_HEAD(list); + + dev_vdbg(chan2dev(&atchan->chan_common), "complete all\n"); + + BUG_ON(atc_chan_is_enabled(atchan)); + + /* + * Submit queued descriptors ASAP, i.e. before we go through + * the completed ones. + */ + if (!list_empty(&atchan->queue)) + atc_dostart(atchan, atc_first_queued(atchan)); + /* empty active_list now it is completed */ + list_splice_init(&atchan->active_list, &list); + /* empty queue list by moving descriptors (if any) to active_list */ + list_splice_init(&atchan->queue, &atchan->active_list); + + list_for_each_entry_safe(desc, _desc, &list, desc_node) + atc_chain_complete(atchan, desc); +} + +/** + * atc_cleanup_descriptors - cleanup up finished descriptors in active_list + * @atchan: channel to be cleaned up + * + * Called with atchan->lock held and bh disabled + */ +static void atc_cleanup_descriptors(struct at_dma_chan *atchan) +{ + struct at_desc *desc, *_desc; + struct at_desc *child; + + dev_vdbg(chan2dev(&atchan->chan_common), "cleanup descriptors\n"); + + list_for_each_entry_safe(desc, _desc, &atchan->active_list, desc_node) { + if (!(desc->lli.ctrla & ATC_DONE)) + /* This one is currently in progress */ + return; + + list_for_each_entry(child, &desc->txd.tx_list, desc_node) + if (!(child->lli.ctrla & ATC_DONE)) + /* Currently in progress */ + return; + + /* + * No descriptors so far seem to be in progress, i.e. + * this chain must be done. + */ + atc_chain_complete(atchan, desc); + } +} + +/** + * atc_advance_work - at the end of a transaction, move forward + * @atchan: channel where the transaction ended + * + * Called with atchan->lock held and bh disabled + */ +static void atc_advance_work(struct at_dma_chan *atchan) +{ + dev_vdbg(chan2dev(&atchan->chan_common), "advance_work\n"); + + if (list_empty(&atchan->active_list) || + list_is_singular(&atchan->active_list)) { + atc_complete_all(atchan); + } else { + atc_chain_complete(atchan, atc_first_active(atchan)); + /* advance work */ + atc_dostart(atchan, atc_first_active(atchan)); + } +} + + +/** + * atc_handle_error - handle errors reported by DMA controller + * @atchan: channel where error occurs + * + * Called with atchan->lock held and bh disabled + */ +static void atc_handle_error(struct at_dma_chan *atchan) +{ + struct at_desc *bad_desc; + struct at_desc *child; + + /* + * The descriptor currently at the head of the active list is + * broked. Since we don't have any way to report errors, we'll + * just have to scream loudly and try to carry on. + */ + bad_desc = atc_first_active(atchan); + list_del_init(&bad_desc->desc_node); + + /* As we are stopped, take advantage to push queued descriptors + * in active_list */ + list_splice_init(&atchan->queue, atchan->active_list.prev); + + /* Try to restart the controller */ + if (!list_empty(&atchan->active_list)) + atc_dostart(atchan, atc_first_active(atchan)); + + /* + * KERN_CRITICAL may seem harsh, but since this only happens + * when someone submits a bad physical address in a + * descriptor, we should consider ourselves lucky that the + * controller flagged an error instead of scribbling over + * random memory locations. + */ + dev_crit(chan2dev(&atchan->chan_common), + "Bad descriptor submitted for DMA!\n"); + dev_crit(chan2dev(&atchan->chan_common), + " cookie: %d\n", bad_desc->txd.cookie); + atc_dump_lli(atchan, &bad_desc->lli); + list_for_each_entry(child, &bad_desc->txd.tx_list, desc_node) + atc_dump_lli(atchan, &child->lli); + + /* Pretend the descriptor completed successfully */ + atc_chain_complete(atchan, bad_desc); +} + + +/*-- IRQ & Tasklet ---------------------------------------------------*/ + +static void atc_tasklet(unsigned long data) +{ + struct at_dma_chan *atchan = (struct at_dma_chan *)data; + + /* Channel cannot be enabled here */ + if (atc_chan_is_enabled(atchan)) { + dev_err(chan2dev(&atchan->chan_common), + "BUG: channel enabled in tasklet\n"); + return; + } + + spin_lock(&atchan->lock); + if (test_and_clear_bit(0, &atchan->error_status)) + atc_handle_error(atchan); + else + atc_advance_work(atchan); + + spin_unlock(&atchan->lock); +} + +static irqreturn_t at_dma_interrupt(int irq, void *dev_id) +{ + struct at_dma *atdma = (struct at_dma *)dev_id; + struct at_dma_chan *atchan; + int i; + u32 status, pending, imr; + int ret = IRQ_NONE; + + do { + imr = dma_readl(atdma, EBCIMR); + status = dma_readl(atdma, EBCISR); + pending = status & imr; + + if (!pending) + break; + + dev_vdbg(atdma->dma_common.dev, + "interrupt: status = 0x%08x, 0x%08x, 0x%08x\n", + status, imr, pending); + + for (i = 0; i < atdma->dma_common.chancnt; i++) { + atchan = &atdma->chan[i]; + if (pending & (AT_DMA_CBTC(i) | AT_DMA_ERR(i))) { + if (pending & AT_DMA_ERR(i)) { + /* Disable channel on AHB error */ + dma_writel(atdma, CHDR, atchan->mask); + /* Give information to tasklet */ + set_bit(0, &atchan->error_status); + } + tasklet_schedule(&atchan->tasklet); + ret = IRQ_HANDLED; + } + } + + } while (pending); + + return ret; +} + + +/*-- DMA Engine API --------------------------------------------------*/ + +/** + * atc_tx_submit - set the prepared descriptor(s) to be executed by the engine + * @desc: descriptor at the head of the transaction chain + * + * Queue chain if DMA engine is working already + * + * Cookie increment and adding to active_list or queue must be atomic + */ +static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx) +{ + struct at_desc *desc = txd_to_at_desc(tx); + struct at_dma_chan *atchan = to_at_dma_chan(tx->chan); + dma_cookie_t cookie; + + spin_lock_bh(&atchan->lock); + cookie = atc_assign_cookie(atchan, desc); + + if (list_empty(&atchan->active_list)) { + dev_vdbg(chan2dev(tx->chan), "tx_submit: started %u\n", + desc->txd.cookie); + atc_dostart(atchan, desc); + list_add_tail(&desc->desc_node, &atchan->active_list); + } else { + dev_vdbg(chan2dev(tx->chan), "tx_submit: queued %u\n", + desc->txd.cookie); + list_add_tail(&desc->desc_node, &atchan->queue); + } + + spin_unlock_bh(&atchan->lock); + + return cookie; +} + +/** + * atc_prep_dma_memcpy - prepare a memcpy operation + * @chan: the channel to prepare operation on + * @dest: operation virtual destination address + * @src: operation virtual source address + * @len: operation length + * @flags: tx descriptor status flags + */ +static struct dma_async_tx_descriptor * +atc_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src, + size_t len, unsigned long flags) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_desc *desc = NULL; + struct at_desc *first = NULL; + struct at_desc *prev = NULL; + size_t xfer_count; + size_t offset; + unsigned int src_width; + unsigned int dst_width; + u32 ctrla; + u32 ctrlb; + + dev_vdbg(chan2dev(chan), "prep_dma_memcpy: d0x%x s0x%x l0x%zx f0x%lx\n", + dest, src, len, flags); + + if (unlikely(!len)) { + dev_dbg(chan2dev(chan), "prep_dma_memcpy: length is zero!\n"); + return NULL; + } + + ctrla = ATC_DEFAULT_CTRLA; + ctrlb = ATC_DEFAULT_CTRLB + | ATC_SRC_ADDR_MODE_INCR + | ATC_DST_ADDR_MODE_INCR + | ATC_FC_MEM2MEM; + + /* + * We can be a lot more clever here, but this should take care + * of the most common optimization. + */ + if (!((src | dest | len) & 3)) { + ctrla |= ATC_SRC_WIDTH_WORD | ATC_DST_WIDTH_WORD; + src_width = dst_width = 2; + } else if (!((src | dest | len) & 1)) { + ctrla |= ATC_SRC_WIDTH_HALFWORD | ATC_DST_WIDTH_HALFWORD; + src_width = dst_width = 1; + } else { + ctrla |= ATC_SRC_WIDTH_BYTE | ATC_DST_WIDTH_BYTE; + src_width = dst_width = 0; + } + + for (offset = 0; offset < len; offset += xfer_count << src_width) { + xfer_count = min_t(size_t, (len - offset) >> src_width, + ATC_BTSIZE_MAX); + + desc = atc_desc_get(atchan); + if (!desc) + goto err_desc_get; + + desc->lli.saddr = src + offset; + desc->lli.daddr = dest + offset; + desc->lli.ctrla = ctrla | xfer_count; + desc->lli.ctrlb = ctrlb; + + desc->txd.cookie = 0; + async_tx_ack(&desc->txd); + + if (!first) { + first = desc; + } else { + /* inform the HW lli about chaining */ + prev->lli.dscr = desc->txd.phys; + /* insert the link descriptor to the LD ring */ + list_add_tail(&desc->desc_node, + &first->txd.tx_list); + } + prev = desc; + } + + /* First descriptor of the chain embedds additional information */ + first->txd.cookie = -EBUSY; + first->len = len; + + /* set end-of-link to the last link descriptor of list*/ + set_desc_eol(desc); + + desc->txd.flags = flags; /* client is in control of this ack */ + + return &first->txd; + +err_desc_get: + atc_desc_put(atchan, first); + return NULL; +} + +/** + * atc_is_tx_complete - poll for transaction completion + * @chan: DMA channel + * @cookie: transaction identifier to check status of + * @done: if not %NULL, updated with last completed transaction + * @used: if not %NULL, updated with last used transaction + * + * If @done and @used are passed in, upon return they reflect the driver + * internal state and can be used with dma_async_is_complete() to check + * the status of multiple cookies without re-checking hardware state. + */ +static enum dma_status +atc_is_tx_complete(struct dma_chan *chan, + dma_cookie_t cookie, + dma_cookie_t *done, dma_cookie_t *used) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + dma_cookie_t last_used; + dma_cookie_t last_complete; + enum dma_status ret; + + dev_vdbg(chan2dev(chan), "is_tx_complete: %d (d%d, u%d)\n", + cookie, done ? *done : 0, used ? *used : 0); + + spin_lock_bh(atchan->lock); + + last_complete = atchan->completed_cookie; + last_used = chan->cookie; + + ret = dma_async_is_complete(cookie, last_complete, last_used); + if (ret != DMA_SUCCESS) { + atc_cleanup_descriptors(atchan); + + last_complete = atchan->completed_cookie; + last_used = chan->cookie; + + ret = dma_async_is_complete(cookie, last_complete, last_used); + } + + spin_unlock_bh(atchan->lock); + + if (done) + *done = last_complete; + if (used) + *used = last_used; + + return ret; +} + +/** + * atc_issue_pending - try to finish work + * @chan: target DMA channel + */ +static void atc_issue_pending(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + + dev_vdbg(chan2dev(chan), "issue_pending\n"); + + if (!atc_chan_is_enabled(atchan)) { + spin_lock_bh(&atchan->lock); + atc_advance_work(atchan); + spin_unlock_bh(&atchan->lock); + } +} + +/** + * atc_alloc_chan_resources - allocate resources for DMA channel + * @chan: allocate descriptor resources for this channel + * @client: current client requesting the channel be ready for requests + * + * return - the number of allocated descriptors + */ +static int atc_alloc_chan_resources(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma *atdma = to_at_dma(chan->device); + struct at_desc *desc; + int i; + LIST_HEAD(tmp_list); + + dev_vdbg(chan2dev(chan), "alloc_chan_resources\n"); + + /* ASSERT: channel is idle */ + if (atc_chan_is_enabled(atchan)) { + dev_dbg(chan2dev(chan), "DMA channel not idle ?\n"); + return -EIO; + } + + /* have we already been set up? */ + if (!list_empty(&atchan->free_list)) + return atchan->descs_allocated; + + /* Allocate initial pool of descriptors */ + for (i = 0; i < init_nr_desc_per_channel; i++) { + desc = atc_alloc_descriptor(chan, GFP_KERNEL); + if (!desc) { + dev_err(atdma->dma_common.dev, + "Only %d initial descriptors\n", i); + break; + } + list_add_tail(&desc->desc_node, &tmp_list); + } + + spin_lock_bh(&atchan->lock); + atchan->descs_allocated = i; + list_splice(&tmp_list, &atchan->free_list); + atchan->completed_cookie = chan->cookie = 1; + spin_unlock_bh(&atchan->lock); + + /* channel parameters */ + channel_writel(atchan, CFG, ATC_DEFAULT_CFG); + + dev_dbg(chan2dev(chan), + "alloc_chan_resources: allocated %d descriptors\n", + atchan->descs_allocated); + + return atchan->descs_allocated; +} + +/** + * atc_free_chan_resources - free all channel resources + * @chan: DMA channel + */ +static void atc_free_chan_resources(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma *atdma = to_at_dma(chan->device); + struct at_desc *desc, *_desc; + LIST_HEAD(list); + + dev_dbg(chan2dev(chan), "free_chan_resources: (descs allocated=%u)\n", + atchan->descs_allocated); + + /* ASSERT: channel is idle */ + BUG_ON(!list_empty(&atchan->active_list)); + BUG_ON(!list_empty(&atchan->queue)); + BUG_ON(atc_chan_is_enabled(atchan)); + + list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) { + dev_vdbg(chan2dev(chan), " freeing descriptor %p\n", desc); + list_del(&desc->desc_node); + /* free link descriptor */ + dma_pool_free(atdma->dma_desc_pool, desc, desc->txd.phys); + } + list_splice_init(&atchan->free_list, &list); + atchan->descs_allocated = 0; + + dev_vdbg(chan2dev(chan), "free_chan_resources: done\n"); +} + + +/*-- Module Management -----------------------------------------------*/ + +/** + * at_dma_off - disable DMA controller + * @atdma: the Atmel HDAMC device + */ +static void at_dma_off(struct at_dma *atdma) +{ + dma_writel(atdma, EN, 0); + + /* disable all interrupts */ + dma_writel(atdma, EBCIDR, -1L); + + /* confirm that all channels are disabled */ + while (dma_readl(atdma, CHSR) & atdma->all_chan_mask) + cpu_relax(); +} + +static int __init at_dma_probe(struct platform_device *pdev) +{ + struct at_dma_platform_data *pdata; + struct resource *io; + struct at_dma *atdma; + size_t size; + int irq; + int err; + int i; + + /* get DMA Controller parameters from platform */ + pdata = pdev->dev.platform_data; + if (!pdata || pdata->nr_channels > AT_DMA_MAX_NR_CHANNELS) + return -EINVAL; + + io = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!io) + return -EINVAL; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + size = sizeof(struct at_dma); + size += pdata->nr_channels * sizeof(struct at_dma_chan); + atdma = kzalloc(size, GFP_KERNEL); + if (!atdma) + return -ENOMEM; + + /* discover transaction capabilites from the platform data */ + atdma->dma_common.cap_mask = pdata->cap_mask; + atdma->all_chan_mask = (1 << pdata->nr_channels) - 1; + + size = io->end - io->start + 1; + if (!request_mem_region(io->start, size, pdev->dev.driver->name)) { + err = -EBUSY; + goto err_kfree; + } + + atdma->regs = ioremap(io->start, size); + if (!atdma->regs) { + err = -ENOMEM; + goto err_release_r; + } + + atdma->clk = clk_get(&pdev->dev, "dma_clk"); + if (IS_ERR(atdma->clk)) { + err = PTR_ERR(atdma->clk); + goto err_clk; + } + clk_enable(atdma->clk); + + /* force dma off, just in case */ + at_dma_off(atdma); + + err = request_irq(irq, at_dma_interrupt, 0, "at_hdmac", atdma); + if (err) + goto err_irq; + + platform_set_drvdata(pdev, atdma); + + /* create a pool of consistent memory blocks for hardware descriptors */ + atdma->dma_desc_pool = dma_pool_create("at_hdmac_desc_pool", + &pdev->dev, sizeof(struct at_desc), + 4 /* word alignment */, 0); + if (!atdma->dma_desc_pool) { + dev_err(&pdev->dev, "No memory for descriptors dma pool\n"); + err = -ENOMEM; + goto err_pool_create; + } + + /* clear any pending interrupt */ + while (dma_readl(atdma, EBCISR)) + cpu_relax(); + + /* initialize channels related values */ + INIT_LIST_HEAD(&atdma->dma_common.channels); + for (i = 0; i < pdata->nr_channels; i++, atdma->dma_common.chancnt++) { + struct at_dma_chan *atchan = &atdma->chan[i]; + + atchan->chan_common.device = &atdma->dma_common; + atchan->chan_common.cookie = atchan->completed_cookie = 1; + atchan->chan_common.chan_id = i; + list_add_tail(&atchan->chan_common.device_node, + &atdma->dma_common.channels); + + atchan->ch_regs = atdma->regs + ch_regs(i); + spin_lock_init(&atchan->lock); + atchan->mask = 1 << i; + + INIT_LIST_HEAD(&atchan->active_list); + INIT_LIST_HEAD(&atchan->queue); + INIT_LIST_HEAD(&atchan->free_list); + + tasklet_init(&atchan->tasklet, atc_tasklet, + (unsigned long)atchan); + atc_enable_irq(atchan); + } + + /* set base routines */ + atdma->dma_common.device_alloc_chan_resources = atc_alloc_chan_resources; + atdma->dma_common.device_free_chan_resources = atc_free_chan_resources; + atdma->dma_common.device_is_tx_complete = atc_is_tx_complete; + atdma->dma_common.device_issue_pending = atc_issue_pending; + atdma->dma_common.dev = &pdev->dev; + + /* set prep routines based on capability */ + if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask)) + atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy; + + dma_writel(atdma, EN, AT_DMA_ENABLE); + + dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s), %d channels\n", + dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask) ? "cpy " : "", + dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask) ? "slave " : "", + atdma->dma_common.chancnt); + + dma_async_device_register(&atdma->dma_common); + + return 0; + +err_pool_create: + platform_set_drvdata(pdev, NULL); + free_irq(platform_get_irq(pdev, 0), atdma); +err_irq: + clk_disable(atdma->clk); + clk_put(atdma->clk); +err_clk: + iounmap(atdma->regs); + atdma->regs = NULL; +err_release_r: + release_mem_region(io->start, size); +err_kfree: + kfree(atdma); + return err; +} + +static int __exit at_dma_remove(struct platform_device *pdev) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + struct dma_chan *chan, *_chan; + struct resource *io; + + at_dma_off(atdma); + dma_async_device_unregister(&atdma->dma_common); + + dma_pool_destroy(atdma->dma_desc_pool); + platform_set_drvdata(pdev, NULL); + free_irq(platform_get_irq(pdev, 0), atdma); + + list_for_each_entry_safe(chan, _chan, &atdma->dma_common.channels, + device_node) { + struct at_dma_chan *atchan = to_at_dma_chan(chan); + + /* Disable interrupts */ + atc_disable_irq(atchan); + tasklet_disable(&atchan->tasklet); + + tasklet_kill(&atchan->tasklet); + list_del(&chan->device_node); + } + + clk_disable(atdma->clk); + clk_put(atdma->clk); + + iounmap(atdma->regs); + atdma->regs = NULL; + + io = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(io->start, io->end - io->start + 1); + + kfree(atdma); + + return 0; +} + +static void at_dma_shutdown(struct platform_device *pdev) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + + at_dma_off(platform_get_drvdata(pdev)); + clk_disable(atdma->clk); +} + +static int at_dma_suspend_late(struct platform_device *pdev, pm_message_t mesg) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + + at_dma_off(platform_get_drvdata(pdev)); + clk_disable(atdma->clk); + return 0; +} + +static int at_dma_resume_early(struct platform_device *pdev) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + + clk_enable(atdma->clk); + dma_writel(atdma, EN, AT_DMA_ENABLE); + return 0; + +} + +static struct platform_driver at_dma_driver = { + .remove = __exit_p(at_dma_remove), + .shutdown = at_dma_shutdown, + .suspend_late = at_dma_suspend_late, + .resume_early = at_dma_resume_early, + .driver = { + .name = "at_hdmac", + }, +}; + +static int __init at_dma_init(void) +{ + return platform_driver_probe(&at_dma_driver, at_dma_probe); +} +module_init(at_dma_init); + +static void __exit at_dma_exit(void) +{ + platform_driver_unregister(&at_dma_driver); +} +module_exit(at_dma_exit); + +MODULE_DESCRIPTION("Atmel AHB DMA Controller driver"); +MODULE_AUTHOR("Nicolas Ferre "); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:at_hdmac"); diff --git a/drivers/dma/at_hdmac_regs.h b/drivers/dma/at_hdmac_regs.h new file mode 100644 index 000000000000..ad2d4f402bf7 --- /dev/null +++ b/drivers/dma/at_hdmac_regs.h @@ -0,0 +1,386 @@ +/* + * Header file for the Atmel AHB DMA Controller driver + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#ifndef AT_HDMAC_REGS_H +#define AT_HDMAC_REGS_H + +#include + +#define AT_DMA_MAX_NR_CHANNELS 8 + + +#define AT_DMA_GCFG 0x00 /* Global Configuration Register */ +#define AT_DMA_IF_BIGEND(i) (0x1 << (i)) /* AHB-Lite Interface i in Big-endian mode */ +#define AT_DMA_ARB_CFG (0x1 << 4) /* Arbiter mode. */ +#define AT_DMA_ARB_CFG_FIXED (0x0 << 4) +#define AT_DMA_ARB_CFG_ROUND_ROBIN (0x1 << 4) + +#define AT_DMA_EN 0x04 /* Controller Enable Register */ +#define AT_DMA_ENABLE (0x1 << 0) + +#define AT_DMA_SREQ 0x08 /* Software Single Request Register */ +#define AT_DMA_SSREQ(x) (0x1 << ((x) << 1)) /* Request a source single transfer on channel x */ +#define AT_DMA_DSREQ(x) (0x1 << (1 + ((x) << 1))) /* Request a destination single transfer on channel x */ + +#define AT_DMA_CREQ 0x0C /* Software Chunk Transfer Request Register */ +#define AT_DMA_SCREQ(x) (0x1 << ((x) << 1)) /* Request a source chunk transfer on channel x */ +#define AT_DMA_DCREQ(x) (0x1 << (1 + ((x) << 1))) /* Request a destination chunk transfer on channel x */ + +#define AT_DMA_LAST 0x10 /* Software Last Transfer Flag Register */ +#define AT_DMA_SLAST(x) (0x1 << ((x) << 1)) /* This src rq is last tx of buffer on channel x */ +#define AT_DMA_DLAST(x) (0x1 << (1 + ((x) << 1))) /* This dst rq is last tx of buffer on channel x */ + +#define AT_DMA_SYNC 0x14 /* Request Synchronization Register */ +#define AT_DMA_SYR(h) (0x1 << (h)) /* Synchronize handshake line h */ + +/* Error, Chained Buffer transfer completed and Buffer transfer completed Interrupt registers */ +#define AT_DMA_EBCIER 0x18 /* Enable register */ +#define AT_DMA_EBCIDR 0x1C /* Disable register */ +#define AT_DMA_EBCIMR 0x20 /* Mask Register */ +#define AT_DMA_EBCISR 0x24 /* Status Register */ +#define AT_DMA_CBTC_OFFSET 8 +#define AT_DMA_ERR_OFFSET 16 +#define AT_DMA_BTC(x) (0x1 << (x)) +#define AT_DMA_CBTC(x) (0x1 << (AT_DMA_CBTC_OFFSET + (x))) +#define AT_DMA_ERR(x) (0x1 << (AT_DMA_ERR_OFFSET + (x))) + +#define AT_DMA_CHER 0x28 /* Channel Handler Enable Register */ +#define AT_DMA_ENA(x) (0x1 << (x)) +#define AT_DMA_SUSP(x) (0x1 << ( 8 + (x))) +#define AT_DMA_KEEP(x) (0x1 << (24 + (x))) + +#define AT_DMA_CHDR 0x2C /* Channel Handler Disable Register */ +#define AT_DMA_DIS(x) (0x1 << (x)) +#define AT_DMA_RES(x) (0x1 << ( 8 + (x))) + +#define AT_DMA_CHSR 0x30 /* Channel Handler Status Register */ +#define AT_DMA_EMPT(x) (0x1 << (16 + (x))) +#define AT_DMA_STAL(x) (0x1 << (24 + (x))) + + +#define AT_DMA_CH_REGS_BASE 0x3C /* Channel registers base address */ +#define ch_regs(x) (AT_DMA_CH_REGS_BASE + (x) * 0x28) /* Channel x base addr */ + +/* Hardware register offset for each channel */ +#define ATC_SADDR_OFFSET 0x00 /* Source Address Register */ +#define ATC_DADDR_OFFSET 0x04 /* Destination Address Register */ +#define ATC_DSCR_OFFSET 0x08 /* Descriptor Address Register */ +#define ATC_CTRLA_OFFSET 0x0C /* Control A Register */ +#define ATC_CTRLB_OFFSET 0x10 /* Control B Register */ +#define ATC_CFG_OFFSET 0x14 /* Configuration Register */ +#define ATC_SPIP_OFFSET 0x18 /* Src PIP Configuration Register */ +#define ATC_DPIP_OFFSET 0x1C /* Dst PIP Configuration Register */ + + +/* Bitfield definitions */ + +/* Bitfields in DSCR */ +#define ATC_DSCR_IF(i) (0x3 & (i)) /* Dsc feched via AHB-Lite Interface i */ + +/* Bitfields in CTRLA */ +#define ATC_BTSIZE_MAX 0xFFFFUL /* Maximum Buffer Transfer Size */ +#define ATC_BTSIZE(x) (ATC_BTSIZE_MAX & (x)) /* Buffer Transfer Size */ +#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */ +#define ATC_SCSIZE_1 (0x0 << 16) +#define ATC_SCSIZE_4 (0x1 << 16) +#define ATC_SCSIZE_8 (0x2 << 16) +#define ATC_SCSIZE_16 (0x3 << 16) +#define ATC_SCSIZE_32 (0x4 << 16) +#define ATC_SCSIZE_64 (0x5 << 16) +#define ATC_SCSIZE_128 (0x6 << 16) +#define ATC_SCSIZE_256 (0x7 << 16) +#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */ +#define ATC_DCSIZE_1 (0x0 << 20) +#define ATC_DCSIZE_4 (0x1 << 20) +#define ATC_DCSIZE_8 (0x2 << 20) +#define ATC_DCSIZE_16 (0x3 << 20) +#define ATC_DCSIZE_32 (0x4 << 20) +#define ATC_DCSIZE_64 (0x5 << 20) +#define ATC_DCSIZE_128 (0x6 << 20) +#define ATC_DCSIZE_256 (0x7 << 20) +#define ATC_SRC_WIDTH_MASK (0x3 << 24) /* Source Single Transfer Size */ +#define ATC_SRC_WIDTH_BYTE (0x0 << 24) +#define ATC_SRC_WIDTH_HALFWORD (0x1 << 24) +#define ATC_SRC_WIDTH_WORD (0x2 << 24) +#define ATC_DST_WIDTH_MASK (0x3 << 28) /* Destination Single Transfer Size */ +#define ATC_DST_WIDTH_BYTE (0x0 << 28) +#define ATC_DST_WIDTH_HALFWORD (0x1 << 28) +#define ATC_DST_WIDTH_WORD (0x2 << 28) +#define ATC_DONE (0x1 << 31) /* Tx Done (only written back in descriptor) */ + +/* Bitfields in CTRLB */ +#define ATC_SIF(i) (0x3 & (i)) /* Src tx done via AHB-Lite Interface i */ +#define ATC_DIF(i) ((0x3 & (i)) << 4) /* Dst tx done via AHB-Lite Interface i */ +#define ATC_SRC_PIP (0x1 << 8) /* Source Picture-in-Picture enabled */ +#define ATC_DST_PIP (0x1 << 12) /* Destination Picture-in-Picture enabled */ +#define ATC_SRC_DSCR_DIS (0x1 << 16) /* Src Descriptor fetch disable */ +#define ATC_DST_DSCR_DIS (0x1 << 20) /* Dst Descriptor fetch disable */ +#define ATC_FC_MASK (0x7 << 21) /* Choose Flow Controller */ +#define ATC_FC_MEM2MEM (0x0 << 21) /* Mem-to-Mem (DMA) */ +#define ATC_FC_MEM2PER (0x1 << 21) /* Mem-to-Periph (DMA) */ +#define ATC_FC_PER2MEM (0x2 << 21) /* Periph-to-Mem (DMA) */ +#define ATC_FC_PER2PER (0x3 << 21) /* Periph-to-Periph (DMA) */ +#define ATC_FC_PER2MEM_PER (0x4 << 21) /* Periph-to-Mem (Peripheral) */ +#define ATC_FC_MEM2PER_PER (0x5 << 21) /* Mem-to-Periph (Peripheral) */ +#define ATC_FC_PER2PER_PER (0x6 << 21) /* Periph-to-Periph (Src Peripheral) */ +#define ATC_SRC_ADDR_MODE_MASK (0x3 << 24) +#define ATC_SRC_ADDR_MODE_INCR (0x0 << 24) /* Incrementing Mode */ +#define ATC_SRC_ADDR_MODE_DECR (0x1 << 24) /* Decrementing Mode */ +#define ATC_SRC_ADDR_MODE_FIXED (0x2 << 24) /* Fixed Mode */ +#define ATC_DST_ADDR_MODE_MASK (0x3 << 28) +#define ATC_DST_ADDR_MODE_INCR (0x0 << 28) /* Incrementing Mode */ +#define ATC_DST_ADDR_MODE_DECR (0x1 << 28) /* Decrementing Mode */ +#define ATC_DST_ADDR_MODE_FIXED (0x2 << 28) /* Fixed Mode */ +#define ATC_IEN (0x1 << 30) /* BTC interrupt enable (active low) */ +#define ATC_AUTO (0x1 << 31) /* Auto multiple buffer tx enable */ + +/* Bitfields in CFG */ +#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */ +#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */ +#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */ +#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */ +#define ATC_SRC_H2SEL_SW (0x0 << 9) +#define ATC_SRC_H2SEL_HW (0x1 << 9) +#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */ +#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */ +#define ATC_DST_H2SEL_SW (0x0 << 13) +#define ATC_DST_H2SEL_HW (0x1 << 13) +#define ATC_SOD (0x1 << 16) /* Stop On Done */ +#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */ +#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */ +#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */ +#define ATC_LOCK_IF_L_CHUNK (0x0 << 22) +#define ATC_LOCK_IF_L_BUFFER (0x1 << 22) +#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */ +#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */ +#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28) +#define ATC_FIFOCFG_HALFFIFO (0x1 << 28) +#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28) + +/* Bitfields in SPIP */ +#define ATC_SPIP_HOLE(x) (0xFFFFU & (x)) +#define ATC_SPIP_BOUNDARY(x) ((0x3FF & (x)) << 16) + +/* Bitfields in DPIP */ +#define ATC_DPIP_HOLE(x) (0xFFFFU & (x)) +#define ATC_DPIP_BOUNDARY(x) ((0x3FF & (x)) << 16) + + +/*-- descriptors -----------------------------------------------------*/ + +/* LLI == Linked List Item; aka DMA buffer descriptor */ +struct at_lli { + /* values that are not changed by hardware */ + dma_addr_t saddr; + dma_addr_t daddr; + /* value that may get written back: */ + u32 ctrla; + /* more values that are not changed by hardware */ + u32 ctrlb; + dma_addr_t dscr; /* chain to next lli */ +}; + +/** + * struct at_desc - software descriptor + * @at_lli: hardware lli structure + * @txd: support for the async_tx api + * @desc_node: node on the channed descriptors list + * @len: total transaction bytecount + */ +struct at_desc { + /* FIRST values the hardware uses */ + struct at_lli lli; + + /* THEN values for driver housekeeping */ + struct dma_async_tx_descriptor txd; + struct list_head desc_node; + size_t len; +}; + +static inline struct at_desc * +txd_to_at_desc(struct dma_async_tx_descriptor *txd) +{ + return container_of(txd, struct at_desc, txd); +} + + +/*-- Channels --------------------------------------------------------*/ + +/** + * struct at_dma_chan - internal representation of an Atmel HDMAC channel + * @chan_common: common dmaengine channel object members + * @device: parent device + * @ch_regs: memory mapped register base + * @mask: channel index in a mask + * @error_status: transmit error status information from irq handler + * to tasklet (use atomic operations) + * @tasklet: bottom half to finish transaction work + * @lock: serializes enqueue/dequeue operations to descriptors lists + * @completed_cookie: identifier for the most recently completed operation + * @active_list: list of descriptors dmaengine is being running on + * @queue: list of descriptors ready to be submitted to engine + * @free_list: list of descriptors usable by the channel + * @descs_allocated: records the actual size of the descriptor pool + */ +struct at_dma_chan { + struct dma_chan chan_common; + struct at_dma *device; + void __iomem *ch_regs; + u8 mask; + unsigned long error_status; + struct tasklet_struct tasklet; + + spinlock_t lock; + + /* these other elements are all protected by lock */ + dma_cookie_t completed_cookie; + struct list_head active_list; + struct list_head queue; + struct list_head free_list; + unsigned int descs_allocated; +}; + +#define channel_readl(atchan, name) \ + __raw_readl((atchan)->ch_regs + ATC_##name##_OFFSET) + +#define channel_writel(atchan, name, val) \ + __raw_writel((val), (atchan)->ch_regs + ATC_##name##_OFFSET) + +static inline struct at_dma_chan *to_at_dma_chan(struct dma_chan *dchan) +{ + return container_of(dchan, struct at_dma_chan, chan_common); +} + + +/*-- Controller ------------------------------------------------------*/ + +/** + * struct at_dma - internal representation of an Atmel HDMA Controller + * @chan_common: common dmaengine dma_device object members + * @ch_regs: memory mapped register base + * @clk: dma controller clock + * @all_chan_mask: all channels availlable in a mask + * @dma_desc_pool: base of DMA descriptor region (DMA address) + * @chan: channels table to store at_dma_chan structures + */ +struct at_dma { + struct dma_device dma_common; + void __iomem *regs; + struct clk *clk; + + u8 all_chan_mask; + + struct dma_pool *dma_desc_pool; + /* AT THE END channels table */ + struct at_dma_chan chan[0]; +}; + +#define dma_readl(atdma, name) \ + __raw_readl((atdma)->regs + AT_DMA_##name) +#define dma_writel(atdma, name, val) \ + __raw_writel((val), (atdma)->regs + AT_DMA_##name) + +static inline struct at_dma *to_at_dma(struct dma_device *ddev) +{ + return container_of(ddev, struct at_dma, dma_common); +} + + +/*-- Helper functions ------------------------------------------------*/ + +static struct device *chan2dev(struct dma_chan *chan) +{ + return &chan->dev->device; +} +static struct device *chan2parent(struct dma_chan *chan) +{ + return chan->dev->device.parent; +} + +#if defined(VERBOSE_DEBUG) +static void vdbg_dump_regs(struct at_dma_chan *atchan) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + + dev_err(chan2dev(&atchan->chan_common), + " channel %d : imr = 0x%x, chsr = 0x%x\n", + atchan->chan_common.chan_id, + dma_readl(atdma, EBCIMR), + dma_readl(atdma, CHSR)); + + dev_err(chan2dev(&atchan->chan_common), + " channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + channel_readl(atchan, SADDR), + channel_readl(atchan, DADDR), + channel_readl(atchan, CTRLA), + channel_readl(atchan, CTRLB), + channel_readl(atchan, DSCR)); +} +#else +static void vdbg_dump_regs(struct at_dma_chan *atchan) {} +#endif + +static void atc_dump_lli(struct at_dma_chan *atchan, struct at_lli *lli) +{ + dev_printk(KERN_CRIT, chan2dev(&atchan->chan_common), + " desc: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + lli->saddr, lli->daddr, + lli->ctrla, lli->ctrlb, lli->dscr); +} + + +static void atc_setup_irq(struct at_dma_chan *atchan, int on) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + u32 ebci; + + /* enable interrupts on buffer chain completion & error */ + ebci = AT_DMA_CBTC(atchan->chan_common.chan_id) + | AT_DMA_ERR(atchan->chan_common.chan_id); + if (on) + dma_writel(atdma, EBCIER, ebci); + else + dma_writel(atdma, EBCIDR, ebci); +} + +static inline void atc_enable_irq(struct at_dma_chan *atchan) +{ + atc_setup_irq(atchan, 1); +} + +static inline void atc_disable_irq(struct at_dma_chan *atchan) +{ + atc_setup_irq(atchan, 0); +} + + +/** + * atc_chan_is_enabled - test if given channel is enabled + * @atchan: channel we want to test status + */ +static inline int atc_chan_is_enabled(struct at_dma_chan *atchan) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + + return !!(dma_readl(atdma, CHSR) & atchan->mask); +} + + +/** + * set_desc_eol - set end-of-link to descriptor so it will end transfer + * @desc: descriptor, signle or at the end of a chain, to end chain on + */ +static void set_desc_eol(struct at_desc *desc) +{ + desc->lli.ctrlb |= ATC_SRC_DSCR_DIS | ATC_DST_DSCR_DIS; + desc->lli.dscr = 0; +} + +#endif /* AT_HDMAC_REGS_H */ -- cgit v1.2.2 From 808347f6a31792079e345ec865e9cfcb6e8ae6b2 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Wed, 22 Jul 2009 20:04:45 +0200 Subject: dmaengine: at_hdmac: add DMA slave transfers This patch for at_hdmac adds the slave transfers capability to the Atmel DMA controller available on some AT91 SOCs. This allow peripheral to memory and memory to peripheral transfers with hardware handshaking. Slave structure for controller specific information is passed through channel private data. This at_dma_slave structure is defined in at_hdmac.h header file and relative hardware definition are moved to this file from at_hdmac_regs.h. Doing this we allow the channel configuration from platform definition code. This work is intensively based on dw_dmac and several slave implementations. Signed-off-by: Nicolas Ferre Signed-off-by: Dan Williams --- drivers/dma/at_hdmac.c | 208 +++++++++++++++++++++++++++++++++++++++++++- drivers/dma/at_hdmac_regs.h | 49 ++--------- 2 files changed, 214 insertions(+), 43 deletions(-) (limited to 'drivers/dma') diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c index 64dbf0ce128e..9a1e5fb412ed 100644 --- a/drivers/dma/at_hdmac.c +++ b/drivers/dma/at_hdmac.c @@ -608,6 +608,187 @@ err_desc_get: return NULL; } + +/** + * atc_prep_slave_sg - prepare descriptors for a DMA_SLAVE transaction + * @chan: DMA channel + * @sgl: scatterlist to transfer to/from + * @sg_len: number of entries in @scatterlist + * @direction: DMA direction + * @flags: tx descriptor status flags + */ +static struct dma_async_tx_descriptor * +atc_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl, + unsigned int sg_len, enum dma_data_direction direction, + unsigned long flags) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma_slave *atslave = chan->private; + struct at_desc *first = NULL; + struct at_desc *prev = NULL; + u32 ctrla; + u32 ctrlb; + dma_addr_t reg; + unsigned int reg_width; + unsigned int mem_width; + unsigned int i; + struct scatterlist *sg; + size_t total_len = 0; + + dev_vdbg(chan2dev(chan), "prep_slave_sg: %s f0x%lx\n", + direction == DMA_TO_DEVICE ? "TO DEVICE" : "FROM DEVICE", + flags); + + if (unlikely(!atslave || !sg_len)) { + dev_dbg(chan2dev(chan), "prep_dma_memcpy: length is zero!\n"); + return NULL; + } + + reg_width = atslave->reg_width; + + sg_len = dma_map_sg(chan2parent(chan), sgl, sg_len, direction); + + ctrla = ATC_DEFAULT_CTRLA | atslave->ctrla; + ctrlb = ATC_DEFAULT_CTRLB | ATC_IEN; + + switch (direction) { + case DMA_TO_DEVICE: + ctrla |= ATC_DST_WIDTH(reg_width); + ctrlb |= ATC_DST_ADDR_MODE_FIXED + | ATC_SRC_ADDR_MODE_INCR + | ATC_FC_MEM2PER; + reg = atslave->tx_reg; + for_each_sg(sgl, sg, sg_len, i) { + struct at_desc *desc; + u32 len; + u32 mem; + + desc = atc_desc_get(atchan); + if (!desc) + goto err_desc_get; + + mem = sg_phys(sg); + len = sg_dma_len(sg); + mem_width = 2; + if (unlikely(mem & 3 || len & 3)) + mem_width = 0; + + desc->lli.saddr = mem; + desc->lli.daddr = reg; + desc->lli.ctrla = ctrla + | ATC_SRC_WIDTH(mem_width) + | len >> mem_width; + desc->lli.ctrlb = ctrlb; + + if (!first) { + first = desc; + } else { + /* inform the HW lli about chaining */ + prev->lli.dscr = desc->txd.phys; + /* insert the link descriptor to the LD ring */ + list_add_tail(&desc->desc_node, + &first->txd.tx_list); + } + prev = desc; + total_len += len; + } + break; + case DMA_FROM_DEVICE: + ctrla |= ATC_SRC_WIDTH(reg_width); + ctrlb |= ATC_DST_ADDR_MODE_INCR + | ATC_SRC_ADDR_MODE_FIXED + | ATC_FC_PER2MEM; + + reg = atslave->rx_reg; + for_each_sg(sgl, sg, sg_len, i) { + struct at_desc *desc; + u32 len; + u32 mem; + + desc = atc_desc_get(atchan); + if (!desc) + goto err_desc_get; + + mem = sg_phys(sg); + len = sg_dma_len(sg); + mem_width = 2; + if (unlikely(mem & 3 || len & 3)) + mem_width = 0; + + desc->lli.saddr = reg; + desc->lli.daddr = mem; + desc->lli.ctrla = ctrla + | ATC_DST_WIDTH(mem_width) + | len >> mem_width; + desc->lli.ctrlb = ctrlb; + + if (!first) { + first = desc; + } else { + /* inform the HW lli about chaining */ + prev->lli.dscr = desc->txd.phys; + /* insert the link descriptor to the LD ring */ + list_add_tail(&desc->desc_node, + &first->txd.tx_list); + } + prev = desc; + total_len += len; + } + break; + default: + return NULL; + } + + /* set end-of-link to the last link descriptor of list*/ + set_desc_eol(prev); + + /* First descriptor of the chain embedds additional information */ + first->txd.cookie = -EBUSY; + first->len = total_len; + + /* last link descriptor of list is responsible of flags */ + prev->txd.flags = flags; /* client is in control of this ack */ + + return &first->txd; + +err_desc_get: + dev_err(chan2dev(chan), "not enough descriptors available\n"); + atc_desc_put(atchan, first); + return NULL; +} + +static void atc_terminate_all(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma *atdma = to_at_dma(chan->device); + struct at_desc *desc, *_desc; + LIST_HEAD(list); + + /* + * This is only called when something went wrong elsewhere, so + * we don't really care about the data. Just disable the + * channel. We still have to poll the channel enable bit due + * to AHB/HSB limitations. + */ + spin_lock_bh(&atchan->lock); + + dma_writel(atdma, CHDR, atchan->mask); + + /* confirm that this channel is disabled */ + while (dma_readl(atdma, CHSR) & atchan->mask) + cpu_relax(); + + /* active_list entries will end up before queued entries */ + list_splice_init(&atchan->queue, &list); + list_splice_init(&atchan->active_list, &list); + + spin_unlock_bh(&atchan->lock); + + /* Flush all pending and queued descriptors */ + list_for_each_entry_safe(desc, _desc, &list, desc_node) + atc_chain_complete(atchan, desc); +} + /** * atc_is_tx_complete - poll for transaction completion * @chan: DMA channel @@ -686,7 +867,9 @@ static int atc_alloc_chan_resources(struct dma_chan *chan) struct at_dma_chan *atchan = to_at_dma_chan(chan); struct at_dma *atdma = to_at_dma(chan->device); struct at_desc *desc; + struct at_dma_slave *atslave; int i; + u32 cfg; LIST_HEAD(tmp_list); dev_vdbg(chan2dev(chan), "alloc_chan_resources\n"); @@ -697,7 +880,23 @@ static int atc_alloc_chan_resources(struct dma_chan *chan) return -EIO; } - /* have we already been set up? */ + cfg = ATC_DEFAULT_CFG; + + atslave = chan->private; + if (atslave) { + /* + * We need controller-specific data to set up slave + * transfers. + */ + BUG_ON(!atslave->dma_dev || atslave->dma_dev != atdma->dma_common.dev); + + /* if cfg configuration specified take it instad of default */ + if (atslave->cfg) + cfg = atslave->cfg; + } + + /* have we already been set up? + * reconfigure channel but no need to reallocate descriptors */ if (!list_empty(&atchan->free_list)) return atchan->descs_allocated; @@ -719,7 +918,7 @@ static int atc_alloc_chan_resources(struct dma_chan *chan) spin_unlock_bh(&atchan->lock); /* channel parameters */ - channel_writel(atchan, CFG, ATC_DEFAULT_CFG); + channel_writel(atchan, CFG, cfg); dev_dbg(chan2dev(chan), "alloc_chan_resources: allocated %d descriptors\n", @@ -888,6 +1087,11 @@ static int __init at_dma_probe(struct platform_device *pdev) if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask)) atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy; + if (dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask)) { + atdma->dma_common.device_prep_slave_sg = atc_prep_slave_sg; + atdma->dma_common.device_terminate_all = atc_terminate_all; + } + dma_writel(atdma, EN, AT_DMA_ENABLE); dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s), %d channels\n", diff --git a/drivers/dma/at_hdmac_regs.h b/drivers/dma/at_hdmac_regs.h index ad2d4f402bf7..4c972afc49ec 100644 --- a/drivers/dma/at_hdmac_regs.h +++ b/drivers/dma/at_hdmac_regs.h @@ -87,29 +87,14 @@ /* Bitfields in CTRLA */ #define ATC_BTSIZE_MAX 0xFFFFUL /* Maximum Buffer Transfer Size */ #define ATC_BTSIZE(x) (ATC_BTSIZE_MAX & (x)) /* Buffer Transfer Size */ -#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */ -#define ATC_SCSIZE_1 (0x0 << 16) -#define ATC_SCSIZE_4 (0x1 << 16) -#define ATC_SCSIZE_8 (0x2 << 16) -#define ATC_SCSIZE_16 (0x3 << 16) -#define ATC_SCSIZE_32 (0x4 << 16) -#define ATC_SCSIZE_64 (0x5 << 16) -#define ATC_SCSIZE_128 (0x6 << 16) -#define ATC_SCSIZE_256 (0x7 << 16) -#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */ -#define ATC_DCSIZE_1 (0x0 << 20) -#define ATC_DCSIZE_4 (0x1 << 20) -#define ATC_DCSIZE_8 (0x2 << 20) -#define ATC_DCSIZE_16 (0x3 << 20) -#define ATC_DCSIZE_32 (0x4 << 20) -#define ATC_DCSIZE_64 (0x5 << 20) -#define ATC_DCSIZE_128 (0x6 << 20) -#define ATC_DCSIZE_256 (0x7 << 20) +/* Chunck Tranfer size definitions are in at_hdmac.h */ #define ATC_SRC_WIDTH_MASK (0x3 << 24) /* Source Single Transfer Size */ +#define ATC_SRC_WIDTH(x) ((x) << 24) #define ATC_SRC_WIDTH_BYTE (0x0 << 24) #define ATC_SRC_WIDTH_HALFWORD (0x1 << 24) #define ATC_SRC_WIDTH_WORD (0x2 << 24) #define ATC_DST_WIDTH_MASK (0x3 << 28) /* Destination Single Transfer Size */ +#define ATC_DST_WIDTH(x) ((x) << 28) #define ATC_DST_WIDTH_BYTE (0x0 << 28) #define ATC_DST_WIDTH_HALFWORD (0x1 << 28) #define ATC_DST_WIDTH_WORD (0x2 << 28) @@ -129,7 +114,8 @@ #define ATC_FC_PER2PER (0x3 << 21) /* Periph-to-Periph (DMA) */ #define ATC_FC_PER2MEM_PER (0x4 << 21) /* Periph-to-Mem (Peripheral) */ #define ATC_FC_MEM2PER_PER (0x5 << 21) /* Mem-to-Periph (Peripheral) */ -#define ATC_FC_PER2PER_PER (0x6 << 21) /* Periph-to-Periph (Src Peripheral) */ +#define ATC_FC_PER2PER_SRCPER (0x6 << 21) /* Periph-to-Periph (Src Peripheral) */ +#define ATC_FC_PER2PER_DSTPER (0x7 << 21) /* Periph-to-Periph (Dst Peripheral) */ #define ATC_SRC_ADDR_MODE_MASK (0x3 << 24) #define ATC_SRC_ADDR_MODE_INCR (0x0 << 24) /* Incrementing Mode */ #define ATC_SRC_ADDR_MODE_DECR (0x1 << 24) /* Decrementing Mode */ @@ -142,27 +128,7 @@ #define ATC_AUTO (0x1 << 31) /* Auto multiple buffer tx enable */ /* Bitfields in CFG */ -#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */ -#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */ -#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */ -#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */ -#define ATC_SRC_H2SEL_SW (0x0 << 9) -#define ATC_SRC_H2SEL_HW (0x1 << 9) -#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */ -#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */ -#define ATC_DST_H2SEL_SW (0x0 << 13) -#define ATC_DST_H2SEL_HW (0x1 << 13) -#define ATC_SOD (0x1 << 16) /* Stop On Done */ -#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */ -#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */ -#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */ -#define ATC_LOCK_IF_L_CHUNK (0x0 << 22) -#define ATC_LOCK_IF_L_BUFFER (0x1 << 22) -#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */ -#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */ -#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28) -#define ATC_FIFOCFG_HALFFIFO (0x1 << 28) -#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28) +/* are in at_hdmac.h */ /* Bitfields in SPIP */ #define ATC_SPIP_HOLE(x) (0xFFFFU & (x)) @@ -316,11 +282,12 @@ static void vdbg_dump_regs(struct at_dma_chan *atchan) dma_readl(atdma, CHSR)); dev_err(chan2dev(&atchan->chan_common), - " channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + " channel: s0x%x d0x%x ctrl0x%x:0x%x cfg0x%x l0x%x\n", channel_readl(atchan, SADDR), channel_readl(atchan, DADDR), channel_readl(atchan, CTRLA), channel_readl(atchan, CTRLB), + channel_readl(atchan, CFG), channel_readl(atchan, DSCR)); } #else -- cgit v1.2.2