From 12b69a599745fc9e203f61fbb7160b2cc5f479dd Mon Sep 17 00:00:00 2001 From: Arnaud Ebalard Date: Tue, 5 Nov 2013 21:45:48 +0100 Subject: ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable Various Marvell datasheets advertise second PCIe unit of mv78230 flavour of Armada XP as x4/quad x1 capable. This second unit is in fact only x1 capable. This patch fixes current mv78230 .dtsi to reflect that, i.e. makes 1.0 the second interface (instead of 2.0 at the moment). This was successfully tested on a mv78230-based ReadyNAS 2120 platform with a x1 device (FL1009 XHCI controller) connected to this second interface. Signed-off-by: Arnaud Ebalard Acked-by: Thomas Petazzoni Cc: # v3.10.x Signed-off-by: Jason Cooper --- arch/arm/boot/dts/armada-xp-mv78230.dtsi | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi index 3f5e6121c730..98335fb34b7a 100644 --- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi @@ -47,7 +47,7 @@ /* * MV78230 has 2 PCIe units Gen2.0: One unit can be * configured as x4 or quad x1 lanes. One unit is - * x4/x1. + * x1 only. */ pcie-controller { compatible = "marvell,armada-xp-pcie"; @@ -62,10 +62,10 @@ ranges = <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */ - 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */ 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ + 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ @@ -74,8 +74,8 @@ 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ - 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ - 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */>; + 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ + 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */>; pcie@1,0 { device_type = "pci"; @@ -145,20 +145,20 @@ status = "disabled"; }; - pcie@9,0 { + pcie@5,0 { device_type = "pci"; - assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; - reg = <0x4800 0 0 0 0>; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x2800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 - 0x81000000 0 0 0x81000000 0x9 0 1 0>; + ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 + 0x81000000 0 0 0x81000000 0x5 0 1 0>; interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 99>; - marvell,pcie-port = <2>; + interrupt-map = <0 0 0 0 &mpic 62>; + marvell,pcie-port = <1>; marvell,pcie-lane = <0>; - clocks = <&gateclk 26>; + clocks = <&gateclk 9>; status = "disabled"; }; }; -- cgit v1.2.2 From 2163e61c92d9337e721a0d067d88ae62b52e0d3e Mon Sep 17 00:00:00 2001 From: Arnaud Ebalard Date: Tue, 5 Nov 2013 21:46:02 +0100 Subject: ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260 mv78260 flavour of Marvell Armada XP SoC has 3 PCIe units. The two first units are both x4 and quad x1 capable. The third unit is only x4 capable. This patch fixes mv78260 .dtsi to reflect those capabilities. Signed-off-by: Arnaud Ebalard Acked-by: Thomas Petazzoni Cc: # v3.10.x Signed-off-by: Jason Cooper --- arch/arm/boot/dts/armada-xp-mv78260.dtsi | 109 ++++++++++++++++++++++++------- 1 file changed, 85 insertions(+), 24 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi index 3e9fd1353f89..66609684d41b 100644 --- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi @@ -48,7 +48,7 @@ /* * MV78260 has 3 PCIe units Gen2.0: Two units can be * configured as x4 or quad x1 lanes. One unit is - * x4/x1. + * x4 only. */ pcie-controller { compatible = "marvell,armada-xp-pcie"; @@ -68,7 +68,9 @@ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ - 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */ + 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */ + 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */ + 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ @@ -77,10 +79,18 @@ 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ - 0x82000000 0x9 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ - 0x81000000 0x9 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ - 0x82000000 0xa 0 MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */ - 0x81000000 0xa 0 MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO */>; + + 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ + 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ + 0x82000000 0x6 0 MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */ + 0x81000000 0x6 0 MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO */ + 0x82000000 0x7 0 MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */ + 0x81000000 0x7 0 MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO */ + 0x82000000 0x8 0 MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */ + 0x81000000 0x8 0 MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO */ + + 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ + 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */>; pcie@1,0 { device_type = "pci"; @@ -106,8 +116,8 @@ #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 - 0x81000000 0 0 0x81000000 0x2 0 1 0>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &mpic 59>; marvell,pcie-port = <0>; @@ -150,37 +160,88 @@ status = "disabled"; }; - pcie@9,0 { + pcie@5,0 { device_type = "pci"; - assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; - reg = <0x4800 0 0 0 0>; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x2800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 - 0x81000000 0 0 0x81000000 0x9 0 1 0>; + ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 + 0x81000000 0 0 0x81000000 0x5 0 1 0>; interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 99>; - marvell,pcie-port = <2>; + interrupt-map = <0 0 0 0 &mpic 62>; + marvell,pcie-port = <1>; marvell,pcie-lane = <0>; - clocks = <&gateclk 26>; + clocks = <&gateclk 9>; status = "disabled"; }; - pcie@10,0 { + pcie@6,0 { device_type = "pci"; - assigned-addresses = <0x82000800 0 0x82000 0 0x2000>; - reg = <0x5000 0 0 0 0>; + assigned-addresses = <0x82000800 0 0x84000 0 0x2000>; + reg = <0x3000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0 - 0x81000000 0 0 0x81000000 0xa 0 1 0>; + ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0 + 0x81000000 0 0 0x81000000 0x6 0 1 0>; interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 103>; - marvell,pcie-port = <3>; + interrupt-map = <0 0 0 0 &mpic 63>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 10>; + status = "disabled"; + }; + + pcie@7,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x88000 0 0x2000>; + reg = <0x3800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0 + 0x81000000 0 0 0x81000000 0x7 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 64>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 11>; + status = "disabled"; + }; + + pcie@8,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x8c000 0 0x2000>; + reg = <0x4000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0 + 0x81000000 0 0 0x81000000 0x8 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 65>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 12>; + status = "disabled"; + }; + + pcie@9,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; + reg = <0x4800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 + 0x81000000 0 0 0x81000000 0x9 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 99>; + marvell,pcie-port = <2>; marvell,pcie-lane = <0>; - clocks = <&gateclk 27>; + clocks = <&gateclk 26>; status = "disabled"; }; }; -- cgit v1.2.2 From b6dda00cddcc71d2030668bc0cc0fed758c411c2 Mon Sep 17 00:00:00 2001 From: Gregory CLEMENT Date: Mon, 25 Nov 2013 17:26:46 +0100 Subject: ARM: mvebu: use the virtual CPU registers to access coherency registers The Armada XP provides a mechanism called "virtual CPU registers" or "per-CPU register banking", to access the per-CPU registers of the current CPU, without having to worry about finding on which CPU we're running. CPU0 has its registers at 0x21800, CPU1 at 0x21900, CPU2 at 0x21A00 and CPU3 at 0x21B00. The virtual registers accessing the current CPU registers are at 0x21000. However, in the Device Tree node that provides the register addresses for the coherency unit (which is responsible for ensuring coherency between processors, and I/O coherency between processors and the DMA-capable devices), a mistake was made: the CPU0-specific registers were specified instead of the virtual CPU registers. This means that the coherency barrier needed for I/O coherency was not behaving properly when executed from a CPU different from CPU0. This patch fixes that by using the virtual CPU registers. Signed-off-by: Gregory CLEMENT Signed-off-by: Thomas Petazzoni Cc: # v3.8+ Fixes: e60304f8cb7bb5 "arm: mvebu: Add hardware I/O Coherency support" Signed-off-by: Jason Cooper --- arch/arm/boot/dts/armada-370-xp.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 00d6a798c705..7f10f627ae5b 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -118,7 +118,7 @@ coherency-fabric@20200 { compatible = "marvell,coherency-fabric"; - reg = <0x20200 0xb0>, <0x21810 0x1c>; + reg = <0x20200 0xb0>, <0x21010 0x1c>; }; serial@12000 { -- cgit v1.2.2 From 96039f735e290281d0c8a08fc467de2cd610543d Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Mon, 25 Nov 2013 17:26:47 +0100 Subject: ARM: mvebu: re-enable PCIe on Armada 370 DB Commit 14fd8ed0a7fd19913 ("ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes") relocated the PCIe controller DT nodes one level up in the Device Tree, to reflect a more correct representation of the hardware introduced by the mvebu-mbus Device Tree binding. However, while most of the boards were properly adjusted accordingly, the Armada 370 DB board was left unchanged, and therefore, PCIe is seen as not enabled on this board. This patch fixes that by moving the PCIe controller node one level-up in armada-370-db.dts. Signed-off-by: Thomas Petazzoni Cc: # v3.12+ Fixes: 14fd8ed0a7fd19913 "ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes" Signed-off-by: Jason Cooper --- arch/arm/boot/dts/armada-370-db.dts | 28 ++++++++++++++-------------- 1 file changed, 14 insertions(+), 14 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts index 90ce29dbe119..08a56bcfc724 100644 --- a/arch/arm/boot/dts/armada-370-db.dts +++ b/arch/arm/boot/dts/armada-370-db.dts @@ -99,22 +99,22 @@ spi-max-frequency = <50000000>; }; }; + }; - pcie-controller { + pcie-controller { + status = "okay"; + /* + * The two PCIe units are accessible through + * both standard PCIe slots and mini-PCIe + * slots on the board. + */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + pcie@2,0 { + /* Port 1, Lane 0 */ status = "okay"; - /* - * The two PCIe units are accessible through - * both standard PCIe slots and mini-PCIe - * slots on the board. - */ - pcie@1,0 { - /* Port 0, Lane 0 */ - status = "okay"; - }; - pcie@2,0 { - /* Port 1, Lane 0 */ - status = "okay"; - }; }; }; }; -- cgit v1.2.2 From 7ce93f3186119754ec7a646bcbeb1f80e4214767 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 25 Nov 2013 14:23:45 -0800 Subject: ARM: OMAP2+: Fix more missing data for omap3.dtsi file After dropping the duplicate data in hwmod that now should come from the .dts files, I noticed few more entries missing. Let's add these as otherwise devices relying on these won't work. Looks like the side tone entries are bundled into the mcbsp1 to 3, so that may needs some special handling in the hwmod code as it's currently trying to look up mcbsp2_sidetone and mcbsp3_sidetone entries. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3.dtsi | 42 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index f3a0c26ed0c2..daabf99d402a 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -82,6 +82,13 @@ ranges; ti,hwmods = "l3_main"; + aes: aes@480c5000 { + compatible = "ti,omap3-aes"; + ti,hwmods = "aes"; + reg = <0x480c5000 0x50>; + interrupts = <0>; + }; + counter32k: counter@48320000 { compatible = "ti,omap-counter32k"; reg = <0x48320000 0x20>; @@ -260,6 +267,13 @@ ti,hwmods = "i2c3"; }; + mailbox: mailbox@48094000 { + compatible = "ti,omap3-mailbox"; + ti,hwmods = "mailbox"; + reg = <0x48094000 0x200>; + interrupts = <26>; + }; + mcspi1: spi@48098000 { compatible = "ti,omap2-mcspi"; reg = <0x48098000 0x100>; @@ -357,6 +371,13 @@ dma-names = "tx", "rx"; }; + mmu_isp: mmu@480bd400 { + compatible = "ti,omap3-mmu-isp"; + ti,hwmods = "mmu_isp"; + reg = <0x480bd400 0x80>; + interrupts = <8>; + }; + wdt2: wdt@48314000 { compatible = "ti,omap3-wdt"; reg = <0x48314000 0x80>; @@ -442,6 +463,27 @@ dma-names = "tx", "rx"; }; + sham: sham@480c3000 { + compatible = "ti,omap3-sham"; + ti,hwmods = "sham"; + reg = <0x480c3000 0x64>; + interrupts = <49>; + }; + + smartreflex_core: smartreflex@480cb000 { + compatible = "ti,omap3-smartreflex-core"; + ti,hwmods = "smartreflex_core"; + reg = <0x480cb000 0x400>; + interrupts = <19>; + }; + + smartreflex_mpu_iva: smartreflex@480c9000 { + compatible = "ti,omap3-smartreflex-iva"; + ti,hwmods = "smartreflex_mpu_iva"; + reg = <0x480c9000 0x400>; + interrupts = <18>; + }; + timer1: timer@48318000 { compatible = "ti,omap3430-timer"; reg = <0x48318000 0x400>; -- cgit v1.2.2 From edd5eb4e99e4153ea7be05390fda542d986bf28d Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 25 Nov 2013 14:23:45 -0800 Subject: ARM: OMAP2+: Fix eMMC on n900 with device tree Looks like we need to configure the regulators and use the pdata quirk to make eMMC work with device tree. It seems that mostly vaux3 is used, and only some earlier revisions used vmmc2. This has been tested to work on devices where the system_rev passed by the bootloader has versions 0x0010, 0x2101 and 0x2204. Cc: devicetree@vger.kernel.org Cc: Pavel Machek Cc: Aaro Koskinen Signed-off-by: Sebastian Reichel [tony@atomide.com: updated with pinctrl changes and comments from Sebastian] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-n900.dts | 23 ++++++++++++++++++++++- 1 file changed, 22 insertions(+), 1 deletion(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index c4f20bfe4cce..c2c306d13b87 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -125,6 +125,21 @@ >; }; + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */ + 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */ + 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */ + 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */ + 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */ + 0x136 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */ + 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */ + 0x13a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */ + >; + }; + display_pins: pinmux_display_pins { pinctrl-single,pins = < 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */ @@ -358,8 +373,14 @@ cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */ }; +/* most boards use vaux3, only some old versions use vmmc2 instead */ &mmc2 { - status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&vaux3>; + vmmc_aux-supply = <&vsim>; + bus-width = <8>; + non-removable; }; &mmc3 { -- cgit v1.2.2 From 8559133d82560a8b1f5d32419c6c829d81b89fb1 Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Tue, 26 Nov 2013 15:03:36 -0800 Subject: ARM: dts: omap3-igep: Fix bus-width for mmc1 Both, IGEPv2 and IGEP COM MODULE have a bus-width of 4 not 8, so fix this and do not mux data pins from mmc1_data4 to mmc1_data7. Signed-off-by: Enric Balletbo i Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep.dtsi | 6 +----- 1 file changed, 1 insertion(+), 5 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index ba1e58b7b7e3..d4fecce91066 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -65,10 +65,6 @@ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ - 0x120 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */ - 0x122 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */ - 0x124 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */ - 0x126 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */ >; }; @@ -114,7 +110,7 @@ pinctrl-0 = <&mmc1_pins>; vmmc-supply = <&vmmc1>; vmmc_aux-supply = <&vsim>; - bus-width = <8>; + bus-width = <4>; }; &mmc2 { -- cgit v1.2.2 From 0e9fd77771d0a0c3318905d33f29eec7680dfe5e Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Tue, 26 Nov 2013 15:03:37 -0800 Subject: ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using the same MMC interface and uses the same GPIOs. Signed-off-by: Enric Balletbo i Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep.dtsi | 45 ++++++++++++++++++++++++++++++++++++++- 1 file changed, 44 insertions(+), 1 deletion(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index d4fecce91066..b3517b2910a5 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -24,6 +24,25 @@ ti,mcbsp = <&mcbsp2>; ti,codec = <&twl_audio>; }; + + vdd33: regulator-vdd33 { + compatible = "regulator-fixed"; + regulator-name = "vdd33"; + regulator-always-on; + }; + + lbee1usjyc_vmmc: lbee1usjyc_vmmc { + pinctrl-names = "default"; + pinctrl-0 = <&lbee1usjyc_pins>; + compatible = "regulator-fixed"; + regulator-name = "regulator-lbee1usjyc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>; /* gpio_138 WIFI_PDN */ + startup-delay-us = <10000>; + enable-active-high; + vin-supply = <&vdd33>; + }; }; &omap3_pmx_core { @@ -48,6 +67,15 @@ >; }; + /* WiFi/BT combo */ + lbee1usjyc_pins: pinmux_lbee1usjyc_pins { + pinctrl-single,pins = < + 0x136 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 */ + 0x138 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat6.gpio_138 */ + 0x13a (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 */ + >; + }; + mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < 0x10c (PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */ @@ -68,6 +96,17 @@ >; }; + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + >; + }; + smsc911x_pins: pinmux_smsc911x_pins { pinctrl-single,pins = < 0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ @@ -114,7 +153,11 @@ }; &mmc2 { - status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&lbee1usjyc_vmmc>; + bus-width = <4>; + non-removable; }; &mmc3 { -- cgit v1.2.2 From 9aa36dfd3d9a1c9e305e53f5c0915036c3941a3f Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Tue, 26 Nov 2013 15:03:37 -0800 Subject: ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor Most of the boards are using the TI AM/DM37x processor, there is only a small quantity of IGEP Processor Boards based on TI OMAP3530. So it's better use the omap36xx.dtsi include instead of omap34xx.dtsi include. We can add support for the 34xx based variant later on as needed. To avoid confusion we have added to the model the (TI AM/DM37x) comment. Signed-off-by: Enric Balletbo i Serra [tony@atomide.com: updated comments for the 34xx to 36xx include change] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep.dtsi | 4 ++-- arch/arm/boot/dts/omap3-igep0020.dts | 4 ++-- arch/arm/boot/dts/omap3-igep0030.dts | 4 ++-- 3 files changed, 6 insertions(+), 6 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index b3517b2910a5..e4c87693b100 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -1,5 +1,5 @@ /* - * Device Tree Source for IGEP Technology devices + * Common device tree for IGEP boards based on AM/DM37x * * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra @@ -10,7 +10,7 @@ */ /dts-v1/; -#include "omap34xx.dtsi" +#include "omap36xx.dtsi" / { memory { diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index d5cc79267250..33ce1236e96e 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -1,5 +1,5 @@ /* - * Device Tree Source for IGEPv2 board + * Device Tree Source for IGEPv2 Rev. (TI OMAP AM/DM37x) * * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra @@ -13,7 +13,7 @@ #include "omap-gpmc-smsc911x.dtsi" / { - model = "IGEPv2"; + model = "IGEPv2 (TI OMAP AM/DM37x)"; compatible = "isee,omap3-igep0020", "ti,omap3"; leds { diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index 525e6d9b0978..02a23f8a3384 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -1,5 +1,5 @@ /* - * Device Tree Source for IGEP COM Module + * Device Tree Source for IGEP COM MODULE (TI OMAP AM/DM37x) * * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra @@ -12,7 +12,7 @@ #include "omap3-igep.dtsi" / { - model = "IGEP COM Module"; + model = "IGEP COM MODULE (TI OMAP AM/DM37x)"; compatible = "isee,omap3-igep0030", "ti,omap3"; leds { -- cgit v1.2.2 From d526daebfd88706b52573325920dac33d14a5f6c Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Tue, 26 Nov 2013 15:03:37 -0800 Subject: ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices Add pin muxing support for IGEP boards i2c controllers. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep.dtsi | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index e4c87693b100..165aaf7591ba 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -113,10 +113,33 @@ >; }; + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + 0x18c (PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0x18e (PIN_INPUT | MUX_MODE0) /* i2c2_scl.i2c2_scl */ + 0x190 (PIN_INPUT | MUX_MODE0) /* i2c2_sda.i2c2_sda */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + 0x192 (PIN_INPUT | MUX_MODE0) /* i2c3_scl.i2c3_scl */ + 0x194 (PIN_INPUT | MUX_MODE0) /* i2c3_sda.i2c3_sda */ + >; + }; + leds_pins: pinmux_leds_pins { }; }; &i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; clock-frequency = <2600000>; twl: twl@48 { @@ -136,9 +159,16 @@ #include "twl4030_omap3.dtsi" &i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; clock-frequency = <400000>; }; +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; +}; + &mcbsp2 { pinctrl-names = "default"; pinctrl-0 = <&mcbsp2_pins>; -- cgit v1.2.2 From 50592dc30ca3617b7b66abd7071930e2489bff26 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Tue, 26 Nov 2013 15:03:38 -0800 Subject: ARM: dts: omap3-igep0020: Add pinmuxing for DVI output The IGEPv2 has a TFP410 DPI-to-DVI encoder attached to OMAP's Display SubSystem (DSS). Add mux setup for DSS pins and also for the GPIO 170 pin that is used to ensure that the DVI-D is powered down on power up. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep0020.dts | 41 ++++++++++++++++++++++++++++++++++++ 1 file changed, 41 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index 33ce1236e96e..b9a9e17acb58 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -67,6 +67,8 @@ pinctrl-names = "default"; pinctrl-0 = < &hsusbb1_pins + &tfp410_pins + &dss_pins >; hsusbb1_pins: pinmux_hsusbb1_pins { @@ -85,6 +87,45 @@ 0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d7.hsusb1_data3 */ >; }; + + tfp410_pins: tfp410_dvi_pins { + pinctrl-single,pins = < + 0x196 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ + >; + }; + + dss_pins: pinmux_dss_dvi_pins { + pinctrl-single,pins = < + 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + 0x0ac (PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + 0x0ae (PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + 0x0b0 (PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + 0x0b2 (PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + 0x0b4 (PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + 0x0b6 (PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + 0x0d0 (PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ + 0x0d2 (PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ + 0x0d4 (PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ + 0x0d6 (PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ + 0x0d8 (PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ + 0x0da (PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ + >; + }; }; &leds_pins { -- cgit v1.2.2 From 0710b679862dc730eb9900592649929da3ec824e Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Tue, 26 Nov 2013 15:03:38 -0800 Subject: ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display Enable the hdmi output and the LCD Controller on IGEP AQUILA. Also configure the correct pinmux for output of video data from the SoC to the HDMI encoder. Signed-off-by: Enric Balletbo i Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-base0033.dts | 46 +++++++++++++++++++++++++++++++++++ 1 file changed, 46 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts index b4f95c2bbf74..620970c0c99a 100644 --- a/arch/arm/boot/dts/am335x-base0033.dts +++ b/arch/arm/boot/dts/am335x-base0033.dts @@ -13,4 +13,50 @@ / { model = "IGEP COM AM335x on AQUILA Expansion"; compatible = "isee,am335x-base0033", "isee,am335x-igep0033", "ti,am33xx"; + + hdmi { + compatible = "ti,tilcdc,slave"; + i2c = <&i2c0>; + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_pins>; + pinctrl-1 = <&nxp_hdmi_off_pins>; + status = "okay"; + }; +}; + +&am33xx_pinmux { + nxp_hdmi_pins: pinmux_nxp_hdmi_pins { + pinctrl-single,pins = < + 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0 */ + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1 */ + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2 */ + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3 */ + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4 */ + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5 */ + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6 */ + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7 */ + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8 */ + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9 */ + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10 */ + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11 */ + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12 */ + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13 */ + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14 */ + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15 */ + 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync */ + 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync */ + 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk */ + 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en */ + >; + }; + nxp_hdmi_off_pins: pinmux_nxp_hdmi_off_pins { + pinctrl-single,pins = < + 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ + >; + }; +}; + +&lcdc { + status = "okay"; }; -- cgit v1.2.2 From f3689fd6dd30974d5b5ccf1daea964440ca5955f Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Tue, 26 Nov 2013 15:03:38 -0800 Subject: ARM: dts: AM33XX BASE0033: add pinmux and user led support Enable the user leds on the IGEP AQUILA EXPANSION. The has two leds, one green and one red, that are controllable by software. Signed-off-by: Enric Balletbo i Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-base0033.dts | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts index 620970c0c99a..ffae1482d954 100644 --- a/arch/arm/boot/dts/am335x-base0033.dts +++ b/arch/arm/boot/dts/am335x-base0033.dts @@ -22,6 +22,25 @@ pinctrl-1 = <&nxp_hdmi_off_pins>; status = "okay"; }; + + leds_base { + pinctrl-names = "default"; + pinctrl-0 = <&leds_base_pins>; + + compatible = "gpio-leds"; + + led@0 { + label = "base:red:user"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; /* gpio1_21 */ + default-state = "off"; + }; + + led@1 { + label = "base:green:user"; + gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>; /* gpio2_0 */ + default-state = "off"; + }; + }; }; &am33xx_pinmux { @@ -55,6 +74,13 @@ 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ >; }; + + leds_base_pins: pinmux_leds_base_pins { + pinctrl-single,pins = < + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + 0x88 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn3.gpio2_0 */ + >; + }; }; &lcdc { -- cgit v1.2.2 From d8e5b2bdd3674a65f3f50fb54061516d4b6c999f Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Tue, 26 Nov 2013 15:03:38 -0800 Subject: ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support The IGEP AQUILA EXPANSION has a 32KBit EEPROM for user data storage. Signed-off-by: Enric Balletbo i Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-base0033.dts | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts index ffae1482d954..72a9b3fc4251 100644 --- a/arch/arm/boot/dts/am335x-base0033.dts +++ b/arch/arm/boot/dts/am335x-base0033.dts @@ -86,3 +86,10 @@ &lcdc { status = "okay"; }; + +&i2c0 { + eeprom: eeprom@50 { + compatible = "at,24c256"; + reg = <0x50>; + }; +}; -- cgit v1.2.2 From caa73370ead3160ed6cdabbfeecc5fbbda06d903 Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Tue, 26 Nov 2013 15:03:39 -0800 Subject: ARM: dts: AM33XX IGEP0033: add USB support Add node to support the USB Host and the USB OTG on the IGEP AQUILA Processor Board. Signed-off-by: Enric Balletbo i Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-igep0033.dtsi | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi index 619624479311..7063311a58d9 100644 --- a/arch/arm/boot/dts/am335x-igep0033.dtsi +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi @@ -199,6 +199,35 @@ pinctrl-0 = <&uart0_pins>; }; +&usb { + status = "okay"; + + control@44e10000 { + status = "okay"; + }; + + usb-phy@47401300 { + status = "okay"; + }; + + usb-phy@47401b00 { + status = "okay"; + }; + + usb@47401000 { + status = "okay"; + }; + + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; + + dma-controller@07402000 { + status = "okay"; + }; +}; + #include "tps65910.dtsi" &tps { -- cgit v1.2.2 From 2f2befd820252d05be7b1f5528a57af85338f59c Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Tue, 26 Nov 2013 15:03:39 -0800 Subject: ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi On Device Tree boot the VDDS_DSI regulator is not linked to the DPI device so omapfb driver probing fails with: [ 3.186035] OMAPFB: omapfb_probe [ 3.190704] omapdss DPI error: can't get VDDS_DSI regulator [ 3.196594] omapfb omapfb: failed to connect default display [ 3.202667] omapfb omapfb: failed to init overlay connections [ 3.208892] OMAPFB: free_resources [ 3.212493] OMAPFB: free all fbmem [ 3.216735] omapfb omapfb: failed to setup omapfb As a workaround name the VPLL2 regulator from twl4030 as vdds_dsi so getting the VDDS_DSI regulator will succeed on dpi_init_regulator(). Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep0020.dts | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index b9a9e17acb58..1c7e74d2d2bc 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -215,3 +215,8 @@ &usbhsehci { phys = <&hsusb1_phy>; }; + +&vpll2 { + /* Needed for DSS */ + regulator-name = "vdds_dsi"; +}; -- cgit v1.2.2 From 30023a7e4fef11c596fd7f3c323035c49dfaed85 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 26 Nov 2013 15:03:39 -0800 Subject: ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13) Beagle (rev. C4) and Beagle-XM (all revs) need VAUX2 1.8V supply for the USB PHY. As the generic PHY driver can't handle more than one supply at the moment, we configure this supply to be always on. This will cause a very small power impact if the USB host subsystem is not in use, about 76.86 micro-W + LDO power. Older Beagle boards (prior to C4) don't have VAUX2 connected anywhere, so there won't be any functional impact on those boards other than some additional LDO power consumption. Reported-by: Nishanth Menon Tested-by: Nishanth Menon Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-beagle-xm.dts | 7 +++++++ arch/arm/boot/dts/omap3-beagle.dts | 7 +++++++ 2 files changed, 14 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 31a632f7effb..df33a50bc070 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -215,3 +215,10 @@ &usbhsehci { phys = <0 &hsusb2_phy>; }; + +&vaux2 { + regulator-name = "usb_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index fa532aaacc68..4e384fcc6ad5 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -178,3 +178,10 @@ mode = <3>; power = <50>; }; + +&vaux2 { + regulator-name = "vdd_ehci"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; -- cgit v1.2.2 From d2607c3b78701fed52ba1bb953562da6702b2001 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Mon, 2 Dec 2013 10:58:32 +0100 Subject: ARM: at91: add usart3 alias to dtsi Alias was missing for SoC of the at91sam9x5 familly that embed USART3. Reported-by: Jiri Prchal [b.brezillon@overkiz.com: advised to place changes in at91sam9x5_usart3.dtsi] Acked-by: Boris BREZILLON Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/at91sam9x5_usart3.dtsi | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi index 2347e9563cef..6801106fa1f8 100644 --- a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi +++ b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi @@ -11,6 +11,10 @@ #include / { + aliases { + serial4 = &usart3; + }; + ahb { apb { pinctrl@fffff400 { -- cgit v1.2.2 From 2ba2866f782f7f1c38abc3dd56d3295efd289264 Mon Sep 17 00:00:00 2001 From: Balaji T K Date: Mon, 2 Dec 2013 11:38:13 -0800 Subject: ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core. Fix the following error message: pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38) pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x SDIO card is not detected after moving pin mux to omap4_pmx_core since sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card. This fixes a regression where WLAN did not work after a warm reset or after one up/down cycle that happened when we move omap4 to boot using device tree only. For reference, the kernel bug is described at: https://bugzilla.kernel.org/show_bug.cgi?id=63821 Cc: stable@vger.kernel.org # v3.10+ Signed-off-by: Balaji T K [tony@atomide.com: update comments to describe the regression] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4-panda-common.dtsi | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 298e85020e1b..88c6a05cab41 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -246,15 +246,6 @@ 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ >; }; -}; - -&omap4_pmx_wkup { - led_wkgpio_pins: pinmux_leds_wkpins { - pinctrl-single,pins = < - 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */ - 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ - >; - }; /* * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP @@ -274,7 +265,7 @@ pinctrl-single,pins = < 0x38 (PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */ 0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ - 0x108 (PIN_OUTPUT | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ + 0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ @@ -284,6 +275,15 @@ }; }; +&omap4_pmx_wkup { + led_wkgpio_pins: pinmux_leds_wkpins { + pinctrl-single,pins = < + 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */ + 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ + >; + }; +}; + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins>; -- cgit v1.2.2 From 2562f5281355d59b7ba31a46567e24ede4e2dea1 Mon Sep 17 00:00:00 2001 From: Balaji T K Date: Mon, 2 Dec 2013 11:38:14 -0800 Subject: ARM: dts: omap4-sdp: Fix pin muxing for wl12xx Mux mode for wlan/sdmmc5 should be MODE0 in pinmux_wl12xx_pins and Enable Pull up on sdmmc5_clk to detect SDIO card. This fixes WLAN on omap4-sdp that got broken in v3.10 when we moved omap4 to boot using device tree only as I did not have the WL12XX card in my omap4 SDP to test with. The commit that attempted to make WL12XX working on omap4 SDP was 775d2418f309 (ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for blaze). Signed-off-by: Balaji T K [tony@atomide.com: updated comments for the regression] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4-sdp.dts | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 5fc3f43c5a81..dbc81fb6ef03 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -300,12 +300,12 @@ wl12xx_pins: pinmux_wl12xx_pins { pinctrl-single,pins = < 0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ - 0x108 (PIN_OUTPUT | MUX_MODE3) /* sdmmc5_clk.sdmmc5_clk */ - 0x10a (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_cmd.sdmmc5_cmd */ - 0x10c (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_dat0.sdmmc5_dat0 */ - 0x10e (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_dat1.sdmmc5_dat1 */ - 0x110 (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_dat2.sdmmc5_dat2 */ - 0x112 (PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc5_dat3.sdmmc5_dat3 */ + 0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ + 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ + 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ + 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ + 0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ >; }; }; -- cgit v1.2.2 From 33e9c392adf521b0a5be7ee2b9b28705b47f8967 Mon Sep 17 00:00:00 2001 From: Jarkko Nikula Date: Mon, 2 Dec 2013 11:38:14 -0800 Subject: ARM: dts: omap3-beagle: Add omap-twl4030 audio support This adds typical McBSP2-TWL4030 audio description to the legacy Beagle Board. Signed-off-by: Jarkko Nikula Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-beagle.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 4e384fcc6ad5..3ba4a625ea5b 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -61,6 +61,14 @@ vcc-supply = <&hsusb2_power>; }; + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3beagle"; + + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; + }; + gpio_keys { compatible = "gpio-keys"; @@ -120,6 +128,12 @@ reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; }; }; -- cgit v1.2.2 From ac46bf3933421bde881399d9ad3d165064862cc3 Mon Sep 17 00:00:00 2001 From: Florian Vaussard Date: Mon, 2 Dec 2013 11:38:15 -0800 Subject: ARM: dts: Fix the name of supplies for smsc911x shared by OMAP drivers/net/ethernet/smsc/smsc911x.c is expecting supplies named "vdd33a" and "vddvario". Currently the shared DTS file provides "vmmc" and "vmmc_aux", and the supply lookup will fail: smsc911x 2c000000.ethernet: Looking up vdd33a-supply from device tree smsc911x 2c000000.ethernet: Looking up vdd33a-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed smsc911x 2c000000.ethernet: Looking up vddvario-supply from device tree smsc911x 2c000000.ethernet: Looking up vddvario-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed Fix it! Looks like commmit 6b2978ac40e4 (ARM: dts: Shared file for omap GPMC connected smsc911x) made the problem more visible by moving the smc911x configuration from the omap3-igep0020.dts file to the generic file. But it seems we've had this problem since commit d72b4415011e (ARM: dts: omap3-igep0020: Add SMSC911x LAN chip support). Tested on OMAP3 Overo platform. Signed-off-by: Florian Vaussard [tony@atomide.com: updated comments for the commits causing the problem] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi index 9c18adf788f7..f577b7df9a29 100644 --- a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi +++ b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi @@ -44,8 +44,8 @@ gpmc,wr-access-ns = <186>; gpmc,cycle2cycle-samecsen; gpmc,cycle2cycle-diffcsen; - vmmc-supply = <&vddvario>; - vmmc_aux-supply = <&vdd33a>; + vddvario-supply = <&vddvario>; + vdd33a-supply = <&vdd33a>; reg-io-width = <4>; smsc,save-mac-address; }; -- cgit v1.2.2 From a5c6e87a7b224bdbf57875a9da8f340f5a6abc5a Mon Sep 17 00:00:00 2001 From: Dinh Nguyen Date: Tue, 3 Dec 2013 14:32:10 -0600 Subject: arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk Some of the clocks that were designated gate-clk do not have a gate, so change those clocks to be of periph-clk type. Signed-off-by: Dinh Nguyen Signed-off-by: Olof Johansson --- arch/arm/boot/dts/socfpga.dtsi | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi index 6d09b8d42fdd..f936476c2753 100644 --- a/arch/arm/boot/dts/socfpga.dtsi +++ b/arch/arm/boot/dts/socfpga.dtsi @@ -245,14 +245,14 @@ mpu_periph_clk: mpu_periph_clk { #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; + compatible = "altr,socfpga-perip-clk"; clocks = <&mpuclk>; fixed-divider = <4>; }; mpu_l2_ram_clk: mpu_l2_ram_clk { #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; + compatible = "altr,socfpga-perip-clk"; clocks = <&mpuclk>; fixed-divider = <2>; }; @@ -266,8 +266,9 @@ l3_main_clk: l3_main_clk { #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; + compatible = "altr,socfpga-perip-clk"; clocks = <&mainclk>; + fixed-divider = <1>; }; l3_mp_clk: l3_mp_clk { -- cgit v1.2.2 From a01581857941c003591ab29719554830b363c575 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 6 Dec 2013 14:20:16 -0800 Subject: ARM: dts: Fix missing entries for am3517 On am3517 there are some extra devices compared to omap3.dtsi that we currently have not defined. Let's fix that by adding am3517.dtsi file. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am3517.dtsi | 63 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 63 insertions(+) create mode 100644 arch/arm/boot/dts/am3517.dtsi (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/am3517.dtsi new file mode 100644 index 000000000000..2fbe02faa8b1 --- /dev/null +++ b/arch/arm/boot/dts/am3517.dtsi @@ -0,0 +1,63 @@ +/* + * Device Tree Source for am3517 SoC + * + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include "omap3.dtsi" + +/ { + aliases { + serial3 = &uart4; + }; + + ocp { + am35x_otg_hs: am35x_otg_hs@5c040000 { + compatible = "ti,omap3-musb"; + ti,hwmods = "am35x_otg_hs"; + status = "disabled"; + reg = <0x5c040000 0x1000>; + interrupts = <71>; + interrupt-names = "mc"; + }; + + davinci_emac: ethernet@0x5c000000 { + compatible = "ti,am3517-emac"; + ti,hwmods = "davinci_emac"; + status = "disabled"; + reg = <0x5c000000 0x30000>; + interrupts = <67 68 69 70>; + ti,davinci-ctrl-reg-offset = <0x10000>; + ti,davinci-ctrl-mod-reg-offset = <0>; + ti,davinci-ctrl-ram-offset = <0x20000>; + ti,davinci-ctrl-ram-size = <0x2000>; + ti,davinci-rmii-en = /bits/ 8 <1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + + davinci_mdio: ethernet@0x5c030000 { + compatible = "ti,davinci_mdio"; + ti,hwmods = "davinci_mdio"; + status = "disabled"; + reg = <0x5c030000 0x1000>; + bus_freq = <1000000>; + #address-cells = <1>; + #size-cells = <0>; + }; + + uart4: serial@4809e000 { + compatible = "ti,omap3-uart"; + ti,hwmods = "uart4"; + status = "disabled"; + reg = <0x4809e000 0x400>; + interrupts = <84>; + dmas = <&sdma 55 &sdma 54>; + dma-names = "tx", "rx"; + clock-frequency = <48000000>; + }; + }; +}; -- cgit v1.2.2 From caef4ee8fb35923d970afac202c027600800902e Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Fri, 6 Dec 2013 14:20:17 -0800 Subject: ARM: OMAP2+: Fix the machine entry for am3517 The am3517 is wrongly booting as omap3 which means that the am3517 specific devices like Ethernet won't work when booted with device tree. Now with the new devices defined in am3517.dtsi, let's use that instead of the omap3.dtsi, and add a separate machine entry for am3517 so am3517-evm can use it. Signed-off-by: Nishanth Menon [tony@atomide.com: updated comments and fixed build without omap3] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am3517-evm.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/am3517-evm.dts b/arch/arm/boot/dts/am3517-evm.dts index e99dfaf70052..03fcbf0a88a8 100644 --- a/arch/arm/boot/dts/am3517-evm.dts +++ b/arch/arm/boot/dts/am3517-evm.dts @@ -7,11 +7,11 @@ */ /dts-v1/; -#include "omap34xx.dtsi" +#include "am3517.dtsi" / { - model = "TI AM3517 EVM (AM3517/05)"; - compatible = "ti,am3517-evm", "ti,omap3"; + model = "TI AM3517 EVM (AM3517/05 TMDSEVM3517)"; + compatible = "ti,am3517-evm", "ti,am3517", "ti,omap3"; memory { device_type = "memory"; -- cgit v1.2.2 From f2e2c9d9b4087b74eb9e00d8dfac148354cb0b71 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 6 Dec 2013 14:20:17 -0800 Subject: ARM: dts: Fix booting for secure omaps Commit 7ce93f3 (ARM: OMAP2+: Fix more missing data for omap3.dtsi file) fixed missing device tree data for omaps, but did not account for some of the hardware modules being inaccessible for secure omaps. This causes the following error on secure omaps: Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0c5048 SMP ARM Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.13.0-rc2+ #446 task: ce057b40 ti: ce058000 task.ti: ce058000 PC is at omap_aes_dma_stop+0x24/0x3c LR is at omap_aes_probe+0x1cc/0x584 psr: 60000113 sp : ce059e20 ip : ce0b4ee0 fp : 00000000 r10: c0573ae8 r9 : c0749508 r8 : 00000000 r7 : ce0b4e00 r6 : 00000000 r5 : ce0b4e10 r4 : ce274890 r3 : fa0c5048 r2 : 00000048 r1 : 0000002c r0 : ce274890 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 80004019 DAC: 00000015 Process swapper/0 (pid: 1, stack limit = 0xce058248) Stack: (0xce059e20 to 0xce05a000) 9e20: c0749508 0000a1ff 00000000 c016cd8c c06b5a06 ce2a45f0 ce2a4570 ce0b5fb0 9e40: 00000000 480c5000 480c504f c0abe4e4 00000200 00000000 00000000 00000000 9e60: ce0b4e10 ce0b4e10 c082da3c c082da3c c02b8c70 c077c610 c0749508 00000000 9e80: 00000000 c02b9e7c c02b9e64 ce0b4e10 00000000 c02b8b20 ce0b4e10 ce0b4e44 9ea0: c082da3c c02b8cd8 00000000 ce059eb8 c082da3c c02b7408 ce079edc ce0b1a34 9ec0: c082da3c c082da3c ce2a0280 00000000 c08158d8 c02b8358 c0663405 c0663405 9ee0: 00000073 c082da3c c079e4e8 c07ab3bc c0844340 c02b9334 00000000 00000006 9f00: c079e4e8 c0008920 c067f6bf c0ac7c6b 00000000 c0712e28 00000000 00000000 9f20: c0712e38 ce059f38 00000093 c0ac7c82 00000000 c0058994 00000000 c07130e8 9f40: c07127b8 00000093 00000006 00000006 00000001 00000006 00000006 c079e4e8 9f60: c07ab3bc c0844340 00000093 c0749508 c079e4f4 c0749c64 00000006 00000006 9f80: c0749508 00000000 00000000 c0517e2c 00000000 00000000 00000000 00000000 9fa0: 00000000 c0517e34 00000000 c000dfb8 00000000 00000000 00000000 00000000 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff (omap_aes_probe+0x1cc/0x584) (platform_drv_probe+0x18/0x48) (driver_probe_device+0xb0/0x200) (__driver_attach+0x68/0x8c) (bus_for_each_dev+0x50/0x88) (bus_add_driver+0xcc/0x1c8) (driver_register+0x9c/0xe0) (do_one_initcall+0x98/0x140) (kernel_init_freeable+0x16c/0x23c) (kernel_init+0x8/0x100) (ret_from_fork+0x14/0x3c) Code: e1811002 e5932020 e590300c e0833002 (e593c000) Let's fix the issue by adding omap34xx-hs.dtsi and omap36xx-hs.dtsi and make n900, n9 and n950 to use them. This way we have the aes, sham and timer12 disabled for secure devices the same way legacy booting does based on the omap34xx_gp_hwmod_ocp_ifs and omap36xx_gp_hwmod_ocp_ifs arrays in omap_hwmod_3xxx_data.c. Reported-by: Sebastian Reichel Acked-By: Sebastian Reichel Tested-by: Aaro Koskinen Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-n900.dts | 2 +- arch/arm/boot/dts/omap3-n950-n9.dtsi | 2 +- arch/arm/boot/dts/omap34xx-hs.dtsi | 16 ++++++++++++++++ arch/arm/boot/dts/omap36xx-hs.dtsi | 16 ++++++++++++++++ 4 files changed, 34 insertions(+), 2 deletions(-) create mode 100644 arch/arm/boot/dts/omap34xx-hs.dtsi create mode 100644 arch/arm/boot/dts/omap36xx-hs.dtsi (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index c2c306d13b87..6fc85f963530 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -9,7 +9,7 @@ /dts-v1/; -#include "omap34xx.dtsi" +#include "omap34xx-hs.dtsi" / { model = "Nokia N900"; diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi index 94eb77d3b9dd..5c26c184f2c1 100644 --- a/arch/arm/boot/dts/omap3-n950-n9.dtsi +++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi @@ -8,7 +8,7 @@ * published by the Free Software Foundation. */ -#include "omap36xx.dtsi" +#include "omap36xx-hs.dtsi" / { cpus { diff --git a/arch/arm/boot/dts/omap34xx-hs.dtsi b/arch/arm/boot/dts/omap34xx-hs.dtsi new file mode 100644 index 000000000000..1ff626489546 --- /dev/null +++ b/arch/arm/boot/dts/omap34xx-hs.dtsi @@ -0,0 +1,16 @@ +/* Disabled modules for secure omaps */ + +#include "omap34xx.dtsi" + +/* Secure omaps have some devices inaccessible depending on the firmware */ +&aes { + status = "disabled"; +}; + +&sham { + status = "disabled"; +}; + +&timer12 { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/omap36xx-hs.dtsi b/arch/arm/boot/dts/omap36xx-hs.dtsi new file mode 100644 index 000000000000..2c7febb0e016 --- /dev/null +++ b/arch/arm/boot/dts/omap36xx-hs.dtsi @@ -0,0 +1,16 @@ +/* Disabled modules for secure omaps */ + +#include "omap36xx.dtsi" + +/* Secure omaps have some devices inaccessible depending on the firmware */ +&aes { + status = "disabled"; +}; + +&sham { + status = "disabled"; +}; + +&timer12 { + status = "disabled"; +}; -- cgit v1.2.2 From 378d0aee3b53bd8549b29dcc75f2bf47ee446e8f Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Tue, 10 Dec 2013 19:37:21 +0100 Subject: ARM: sun7i: dt: Fix interrupt trigger types The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The GIC can work on several interrupt triggers, and the A20 was actually setting it up to use a rising edge as a trigger, while it was actually a level high trigger, leading to some interrupts that would be completely ignored if the edge was missed. Signed-off-by: Maxime Ripard Acked-by: Hans de Goede Cc: stable@vger.kernel.org #3.12+ Signed-off-by: Olof Johansson --- arch/arm/boot/dts/sun7i-a20.dtsi | 42 ++++++++++++++++++++-------------------- 1 file changed, 21 insertions(+), 21 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index e46cfedde74c..367611a0730b 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -170,7 +170,7 @@ emac: ethernet@01c0b000 { compatible = "allwinner,sun4i-emac"; reg = <0x01c0b000 0x1000>; - interrupts = <0 55 1>; + interrupts = <0 55 4>; clocks = <&ahb_gates 17>; status = "disabled"; }; @@ -186,7 +186,7 @@ pio: pinctrl@01c20800 { compatible = "allwinner,sun7i-a20-pinctrl"; reg = <0x01c20800 0x400>; - interrupts = <0 28 1>; + interrupts = <0 28 4>; clocks = <&apb0_gates 5>; gpio-controller; interrupt-controller; @@ -251,12 +251,12 @@ timer@01c20c00 { compatible = "allwinner,sun4i-timer"; reg = <0x01c20c00 0x90>; - interrupts = <0 22 1>, - <0 23 1>, - <0 24 1>, - <0 25 1>, - <0 67 1>, - <0 68 1>; + interrupts = <0 22 4>, + <0 23 4>, + <0 24 4>, + <0 25 4>, + <0 67 4>, + <0 68 4>; clocks = <&osc24M>; }; @@ -273,7 +273,7 @@ uart0: serial@01c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; - interrupts = <0 1 1>; + interrupts = <0 1 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 16>; @@ -283,7 +283,7 @@ uart1: serial@01c28400 { compatible = "snps,dw-apb-uart"; reg = <0x01c28400 0x400>; - interrupts = <0 2 1>; + interrupts = <0 2 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 17>; @@ -293,7 +293,7 @@ uart2: serial@01c28800 { compatible = "snps,dw-apb-uart"; reg = <0x01c28800 0x400>; - interrupts = <0 3 1>; + interrupts = <0 3 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 18>; @@ -303,7 +303,7 @@ uart3: serial@01c28c00 { compatible = "snps,dw-apb-uart"; reg = <0x01c28c00 0x400>; - interrupts = <0 4 1>; + interrupts = <0 4 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 19>; @@ -313,7 +313,7 @@ uart4: serial@01c29000 { compatible = "snps,dw-apb-uart"; reg = <0x01c29000 0x400>; - interrupts = <0 17 1>; + interrupts = <0 17 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 20>; @@ -323,7 +323,7 @@ uart5: serial@01c29400 { compatible = "snps,dw-apb-uart"; reg = <0x01c29400 0x400>; - interrupts = <0 18 1>; + interrupts = <0 18 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 21>; @@ -333,7 +333,7 @@ uart6: serial@01c29800 { compatible = "snps,dw-apb-uart"; reg = <0x01c29800 0x400>; - interrupts = <0 19 1>; + interrupts = <0 19 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 22>; @@ -343,7 +343,7 @@ uart7: serial@01c29c00 { compatible = "snps,dw-apb-uart"; reg = <0x01c29c00 0x400>; - interrupts = <0 20 1>; + interrupts = <0 20 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb1_gates 23>; @@ -353,7 +353,7 @@ i2c0: i2c@01c2ac00 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2ac00 0x400>; - interrupts = <0 7 1>; + interrupts = <0 7 4>; clocks = <&apb1_gates 0>; clock-frequency = <100000>; status = "disabled"; @@ -362,7 +362,7 @@ i2c1: i2c@01c2b000 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2b000 0x400>; - interrupts = <0 8 1>; + interrupts = <0 8 4>; clocks = <&apb1_gates 1>; clock-frequency = <100000>; status = "disabled"; @@ -371,7 +371,7 @@ i2c2: i2c@01c2b400 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2b400 0x400>; - interrupts = <0 9 1>; + interrupts = <0 9 4>; clocks = <&apb1_gates 2>; clock-frequency = <100000>; status = "disabled"; @@ -380,7 +380,7 @@ i2c3: i2c@01c2b800 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2b800 0x400>; - interrupts = <0 88 1>; + interrupts = <0 88 4>; clocks = <&apb1_gates 3>; clock-frequency = <100000>; status = "disabled"; @@ -389,7 +389,7 @@ i2c4: i2c@01c2bc00 { compatible = "allwinner,sun4i-i2c"; reg = <0x01c2bc00 0x400>; - interrupts = <0 89 1>; + interrupts = <0 89 4>; clocks = <&apb1_gates 15>; clock-frequency = <100000>; status = "disabled"; -- cgit v1.2.2 From 6f97dc8d4663abed96fa30e3ea4a1d4cfd1c4276 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Tue, 10 Dec 2013 19:37:22 +0100 Subject: ARM: sun6i: dt: Fix interrupt trigger types The Allwinner A31 uses the ARM GIC as its internal interrupts controller. The GIC can work on several interrupt triggers, and the A31 was actually setting it up to use a rising edge as a trigger, while it was actually a level high trigger, leading to some interrupts that would be completely ignored if the edge was missed. Signed-off-by: Maxime Ripard Acked-by: Hans de Goede Cc: stable@vger.kernel.org # 3.12+ Signed-off-by: Olof Johansson --- arch/arm/boot/dts/sun6i-a31.dtsi | 27 +++++++++++++++------------ 1 file changed, 15 insertions(+), 12 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index c1751a64889a..7f5878c2784a 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -193,7 +193,10 @@ pio: pinctrl@01c20800 { compatible = "allwinner,sun6i-a31-pinctrl"; reg = <0x01c20800 0x400>; - interrupts = <0 11 1>, <0 15 1>, <0 16 1>, <0 17 1>; + interrupts = <0 11 4>, + <0 15 4>, + <0 16 4>, + <0 17 4>; clocks = <&apb1_gates 5>; gpio-controller; interrupt-controller; @@ -212,11 +215,11 @@ timer@01c20c00 { compatible = "allwinner,sun4i-timer"; reg = <0x01c20c00 0xa0>; - interrupts = <0 18 1>, - <0 19 1>, - <0 20 1>, - <0 21 1>, - <0 22 1>; + interrupts = <0 18 4>, + <0 19 4>, + <0 20 4>, + <0 21 4>, + <0 22 4>; clocks = <&osc24M>; }; @@ -228,7 +231,7 @@ uart0: serial@01c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; - interrupts = <0 0 1>; + interrupts = <0 0 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 16>; @@ -238,7 +241,7 @@ uart1: serial@01c28400 { compatible = "snps,dw-apb-uart"; reg = <0x01c28400 0x400>; - interrupts = <0 1 1>; + interrupts = <0 1 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 17>; @@ -248,7 +251,7 @@ uart2: serial@01c28800 { compatible = "snps,dw-apb-uart"; reg = <0x01c28800 0x400>; - interrupts = <0 2 1>; + interrupts = <0 2 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 18>; @@ -258,7 +261,7 @@ uart3: serial@01c28c00 { compatible = "snps,dw-apb-uart"; reg = <0x01c28c00 0x400>; - interrupts = <0 3 1>; + interrupts = <0 3 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 19>; @@ -268,7 +271,7 @@ uart4: serial@01c29000 { compatible = "snps,dw-apb-uart"; reg = <0x01c29000 0x400>; - interrupts = <0 4 1>; + interrupts = <0 4 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 20>; @@ -278,7 +281,7 @@ uart5: serial@01c29400 { compatible = "snps,dw-apb-uart"; reg = <0x01c29400 0x400>; - interrupts = <0 5 1>; + interrupts = <0 5 4>; reg-shift = <2>; reg-io-width = <4>; clocks = <&apb2_gates 21>; -- cgit v1.2.2