From b659980014a7f45bfd6a1da9039a0498a28b7a63 Mon Sep 17 00:00:00 2001 From: Uwe Bugla Date: Sat, 25 Jun 2005 14:54:21 -0700 Subject: [PATCH] dvb-bt8xx.txt fixes Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/dvb/bt8xx.txt | 25 +++++++++++-------------- 1 file changed, 11 insertions(+), 14 deletions(-) (limited to 'Documentation') diff --git a/Documentation/dvb/bt8xx.txt b/Documentation/dvb/bt8xx.txt index d64430bf4bb6..3a3260794758 100644 --- a/Documentation/dvb/bt8xx.txt +++ b/Documentation/dvb/bt8xx.txt @@ -44,26 +44,23 @@ TwinHan (dst) are loaded automatically by the dvb-bt8xx device driver. $ modprobe dst The value 0x71 will override the PCI type detection for dvb-bt8xx, -which is necessary for TwinHan cards. +which is necessary for TwinHan cards. If you're having an older card (blue color circuit) and card=0x71 locks your machine, try using 0x68, too. If that does not work, ask on the mailing list. -The DST module takes a couple of useful parameters. +The DST module takes a couple of useful parameters: -verbose takes values 0 to 5. These values control the verbosity level. - -debug takes values 0 and 1. You can either disable or enable debugging. - -dst_addons takes values 0 and 0x20. A value of 0 means it is a FTA card. -0x20 means it has a Conditional Access slot. - -The autodected values are determined bythe cards 'response -string' which you can see in your logs e.g. - -dst_get_device_id: Recognise [DSTMCI] +a. verbose takes values 0 to 5. These values control the verbosity level. +b. debug takes values 0 and 1. You can either disable or enable debugging. +c. dst_addons takes values 0 and 0x20: +- A value of 0 means it is a FTA card. +- A value of 0x20 means it has a Conditional Access slot. +The autodetected values are determined by the "response string" +of the card, which you can see in your logs: +e.g.: dst_get_device_id: Recognize [DSTMCI] -- -Authors: Richard Walker, Jamie Honan, Michael Hunold, Manu Abraham +Authors: Richard Walker, Jamie Honan, Michael Hunold, Manu Abraham, Uwe Bugla -- cgit v1.2.2 From e70c9d5e61c6cb2272c866fc1303e62975006752 Mon Sep 17 00:00:00 2001 From: Dmitry Torokhov Date: Sat, 25 Jun 2005 14:54:25 -0700 Subject: [PATCH] I8K: use standard DMI interface I8K: Change to use stock dmi infrastructure instead of homegrown parsing code. The driver now requires box's DMI data to match list of supported models so driver can be safely compiled-in by default without fear of it poking into random SMM BIOS code. DMI checks can be ignored with i8k.ignore_dmi option. Signed-off-by: Dmitry Torokhov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/kernel-parameters.txt | 3 +++ 1 file changed, 3 insertions(+) (limited to 'Documentation') diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 4924d387a657..86db43fd6b0f 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -548,6 +548,9 @@ running once the system is up. i810= [HW,DRM] + i8k.ignore_dmi [HW] Continue probing hardware even if DMI data + indicates that the driver is running on unsupported + hardware. i8k.force [HW] Activate i8k driver even if SMM BIOS signature does not match list of supported models. i8k.power_status -- cgit v1.2.2 From fc5fb2c609c6acef15a8b062063e9135fb08b4d2 Mon Sep 17 00:00:00 2001 From: Pavel Machek Date: Sat, 25 Jun 2005 14:55:07 -0700 Subject: [PATCH] swsusp: documentation updates This updates documentation and fixes pointers in MAINTAINERS file. Signed-off-by: Pavel Machek Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/power/swsusp.txt | 84 ++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 81 insertions(+), 3 deletions(-) (limited to 'Documentation') diff --git a/Documentation/power/swsusp.txt b/Documentation/power/swsusp.txt index c7c3459fde43..8363c51831d3 100644 --- a/Documentation/power/swsusp.txt +++ b/Documentation/power/swsusp.txt @@ -164,11 +164,11 @@ place where the thread is safe to be frozen (no kernel semaphores should be held at that point and it must be safe to sleep there), and add: - if (current->flags & PF_FREEZE) - refrigerator(PF_FREEZE); + try_to_freeze(PF_FREEZE); If the thread is needed for writing the image to storage, you should -instead set the PF_NOFREEZE process flag when creating the thread. +instead set the PF_NOFREEZE process flag when creating the thread (and +be very carefull). Q: What is the difference between between "platform", "shutdown" and @@ -233,3 +233,81 @@ A: Try running cat `cat /proc/[0-9]*/maps | grep / | sed 's:.* /:/:' | sort -u` > /dev/null after resume. swapoff -a; swapon -a may also be usefull. + +Q: What happens to devices during swsusp? They seem to be resumed +during system suspend? + +A: That's correct. We need to resume them if we want to write image to +disk. Whole sequence goes like + + Suspend part + ~~~~~~~~~~~~ + running system, user asks for suspend-to-disk + + user processes are stopped + + suspend(PMSG_FREEZE): devices are frozen so that they don't interfere + with state snapshot + + state snapshot: copy of whole used memory is taken with interrupts disabled + + resume(): devices are woken up so that we can write image to swap + + write image to swap + + suspend(PMSG_SUSPEND): suspend devices so that we can power off + + turn the power off + + Resume part + ~~~~~~~~~~~ + (is actually pretty similar) + + running system, user asks for suspend-to-disk + + user processes are stopped (in common case there are none, but with resume-from-initrd, noone knows) + + read image from disk + + suspend(PMSG_FREEZE): devices are frozen so that they don't interfere + with image restoration + + image restoration: rewrite memory with image + + resume(): devices are woken up so that system can continue + + thaw all user processes + +Q: What is this 'Encrypt suspend image' for? + +A: First of all: it is not a replacement for dm-crypt encrypted swap. +It cannot protect your computer while it is suspended. Instead it does +protect from leaking sensitive data after resume from suspend. + +Think of the following: you suspend while an application is running +that keeps sensitive data in memory. The application itself prevents +the data from being swapped out. Suspend, however, must write these +data to swap to be able to resume later on. Without suspend encryption +your sensitive data are then stored in plaintext on disk. This means +that after resume your sensitive data are accessible to all +applications having direct access to the swap device which was used +for suspend. If you don't need swap after resume these data can remain +on disk virtually forever. Thus it can happen that your system gets +broken in weeks later and sensitive data which you thought were +encrypted and protected are retrieved and stolen from the swap device. +To prevent this situation you should use 'Encrypt suspend image'. + +During suspend a temporary key is created and this key is used to +encrypt the data written to disk. When, during resume, the data was +read back into memory the temporary key is destroyed which simply +means that all data written to disk during suspend are then +inaccessible so they can't be stolen later on. The only thing that +you must then take care of is that you call 'mkswap' for the swap +partition used for suspend as early as possible during regular +boot. This asserts that any temporary key from an oopsed suspend or +from a failed or aborted resume is erased from the swap device. + +As a rule of thumb use encrypted swap to protect your data while your +system is shut down or suspended. Additionally use the encrypted +suspend image to prevent sensitive data from being stolen after +resume. -- cgit v1.2.2 From 5ce47e59c9688d8480ae41100117d8188c191401 Mon Sep 17 00:00:00 2001 From: Pavel Machek Date: Sat, 25 Jun 2005 14:55:10 -0700 Subject: [PATCH] acpi: fix video docs This fixes typos/formatting in video_extension.txt. Signed-off-by: Pavel Machek Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/power/video_extension.txt | 19 +++++++++++-------- 1 file changed, 11 insertions(+), 8 deletions(-) (limited to 'Documentation') diff --git a/Documentation/power/video_extension.txt b/Documentation/power/video_extension.txt index 8e33d7c82c49..b2f9b1598ac2 100644 --- a/Documentation/power/video_extension.txt +++ b/Documentation/power/video_extension.txt @@ -1,13 +1,16 @@ -This driver implement the ACPI Extensions For Display Adapters -for integrated graphics devices on motherboard, as specified in -ACPI 2.0 Specification, Appendix B, allowing to perform some basic -control like defining the video POST device, retrieving EDID information -or to setup a video output, etc. Note that this is an ref. implementation only. -It may or may not work for your integrated video device. +ACPI video extensions +~~~~~~~~~~~~~~~~~~~~~ + +This driver implement the ACPI Extensions For Display Adapters for +integrated graphics devices on motherboard, as specified in ACPI 2.0 +Specification, Appendix B, allowing to perform some basic control like +defining the video POST device, retrieving EDID information or to +setup a video output, etc. Note that this is an ref. implementation +only. It may or may not work for your integrated video device. Interfaces exposed to userland through /proc/acpi/video: -VGA/info : display the supported video bus device capability like ,Video ROM, CRT/LCD/TV. +VGA/info : display the supported video bus device capability like Video ROM, CRT/LCD/TV. VGA/ROM : Used to get a copy of the display devices' ROM data (up to 4k). VGA/POST_info : Used to determine what options are implemented. VGA/POST : Used to get/set POST device. @@ -15,7 +18,7 @@ VGA/DOS : Used to get/set ownership of output switching: Please refer ACPI spec B.4.1 _DOS VGA/CRT : CRT output VGA/LCD : LCD output -VGA/TV : TV output +VGA/TVO : TV output VGA/*/brightness : Used to get/set brightness of output device Notify event through /proc/acpi/event: -- cgit v1.2.2 From 21d6b7e18f70c847c867aafb3109405b48424388 Mon Sep 17 00:00:00 2001 From: "pavel@ucw.cz" Date: Sat, 25 Jun 2005 14:55:16 -0700 Subject: [PATCH] suspend: PCI power managment reference implementation Added reference implementation of suspend and resume routines. From: Shaohua Li build fix Signed-off-by: Pavel Machek Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/power/pci.txt | 38 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 38 insertions(+) (limited to 'Documentation') diff --git a/Documentation/power/pci.txt b/Documentation/power/pci.txt index 35b1a7dae342..6fc9d511fc39 100644 --- a/Documentation/power/pci.txt +++ b/Documentation/power/pci.txt @@ -291,6 +291,44 @@ a request to enable wake events from D3, two calls should be made to pci_enable_wake (one for both D3hot and D3cold). +A reference implementation +------------------------- +.suspend() +{ + /* driver specific operations */ + + /* Disable IRQ */ + free_irq(); + /* If using MSI */ + pci_disable_msi(); + + pci_save_state(); + pci_enable_wake(); + /* Disable IO/bus master/irq router */ + pci_disable_device(); + pci_set_power_state(pci_choose_state()); +} + +.resume() +{ + pci_set_power_state(PCI_D0); + pci_restore_state(); + /* device's irq possibly is changed, driver should take care */ + pci_enable_device(); + pci_set_master(); + + /* if using MSI, device's vector possibly is changed */ + pci_enable_msi(); + + request_irq(); + /* driver specific operations; */ +} + +This is a typical implementation. Drivers can slightly change the order +of the operations in the implementation, ignore some operations or add +more deriver specific operations in it, but drivers should do something like +this on the whole. + 5. Resources ~~~~~~~~~~~~ -- cgit v1.2.2 From 2a96206559a8c3a18478a6288ac426d716bbd99c Mon Sep 17 00:00:00 2001 From: Pavel Machek Date: Sat, 25 Jun 2005 14:55:18 -0700 Subject: [PATCH] Update video-after-suspend documentation Update video-after-suspend documentation; few more machines are added. Signed-off-by: Pavel Machek Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/power/video.txt | 3 +++ 1 file changed, 3 insertions(+) (limited to 'Documentation') diff --git a/Documentation/power/video.txt b/Documentation/power/video.txt index 68734355d7cf..881a37e3eeb0 100644 --- a/Documentation/power/video.txt +++ b/Documentation/power/video.txt @@ -83,8 +83,10 @@ Compaq Armada E500 - P3-700 none (1) (S1 also works OK) Compaq Evo N620c vga=normal, s3_bios (2) Dell 600m, ATI R250 Lf none (1), but needs xorg-x11-6.8.1.902-1 Dell D600, ATI RV250 vga=normal and X, or try vbestate (6) +Dell D610 vga=normal and X (possibly vbestate (6) too, but not tested) Dell Inspiron 4000 ??? (*) Dell Inspiron 500m ??? (*) +Dell Inspiron 510m ??? Dell Inspiron 600m ??? (*) Dell Inspiron 8200 ??? (*) Dell Inspiron 8500 ??? (*) @@ -123,6 +125,7 @@ Toshiba Satellite 4030CDT s3_mode (3) Toshiba Satellite 4080XCDT s3_mode (3) Toshiba Satellite 4090XCDT ??? (*) Toshiba Satellite P10-554 s3_bios,s3_mode (4)(****) +Toshiba M30 (2) xor X with nvidia driver using internal AGP Uniwill 244IIO ??? (*) -- cgit v1.2.2 From 66a464dbc8e0345b6f972b92bf1118e043d7c987 Mon Sep 17 00:00:00 2001 From: Michael Holzheu Date: Sat, 25 Jun 2005 14:55:33 -0700 Subject: [PATCH] s390: debug feature changes This patch changes the memory allocation method for the s390 debug feature. Trace buffers had been allocated using the get_free_pages() function before. Therefore it was not possible to get big memory areas in a running system due to memory fragmentation. Now the trace buffers are subdivided into several subbuffers with pagesize. Therefore it is now possible to allocate more memory for the trace buffers and more trace records can be written. In addition to that, dynamic specification of the size of the trace buffers is implemented. It is now possible to change the size of a trace buffer using a new debugfs file instance. When writing a number into this file, the trace buffer size is changed to 'number * pagesize'. In the past all the traces could be obtained from userspace by accessing files in the "proc" filesystem. Now with debugfs we have a new filesystem which should be used for debugging purposes. This patch moves the debug feature from procfs to debugfs. Since the interface of debug_register() changed, all device drivers, which use the debug feature had to be adjusted. Signed-off-by: Martin Schwidefsky Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/s390/s390dbf.txt | 79 ++++++++++++++++++++++++------------------ 1 file changed, 46 insertions(+), 33 deletions(-) (limited to 'Documentation') diff --git a/Documentation/s390/s390dbf.txt b/Documentation/s390/s390dbf.txt index 2d1cd939b4df..e24fdeada970 100644 --- a/Documentation/s390/s390dbf.txt +++ b/Documentation/s390/s390dbf.txt @@ -12,8 +12,8 @@ where log records can be stored efficiently in memory, where each component One purpose of this is to inspect the debug logs after a production system crash in order to analyze the reason for the crash. If the system still runs but only a subcomponent which uses dbf failes, -it is possible to look at the debug logs on a live system via the Linux proc -filesystem. +it is possible to look at the debug logs on a live system via the Linux +debugfs filesystem. The debug feature may also very useful for kernel and driver development. Design: @@ -52,16 +52,18 @@ Each debug entry contains the following data: - Flag, if entry is an exception or not The debug logs can be inspected in a live system through entries in -the proc-filesystem. Under the path /proc/s390dbf there is +the debugfs-filesystem. Under the toplevel directory "s390dbf" there is a directory for each registered component, which is named like the -corresponding component. +corresponding component. The debugfs normally should be mounted to +/sys/kernel/debug therefore the debug feature can be accessed unter +/sys/kernel/debug/s390dbf. The content of the directories are files which represent different views to the debug log. Each component can decide which views should be used through registering them with the function debug_register_view(). Predefined views for hex/ascii, sprintf and raw binary data are provided. It is also possible to define other views. The content of -a view can be inspected simply by reading the corresponding proc file. +a view can be inspected simply by reading the corresponding debugfs file. All debug logs have an an actual debug level (range from 0 to 6). The default level is 3. Event and Exception functions have a 'level' @@ -69,14 +71,14 @@ parameter. Only debug entries with a level that is lower or equal than the actual level are written to the log. This means, when writing events, high priority log entries should have a low level value whereas low priority entries should have a high one. -The actual debug level can be changed with the help of the proc-filesystem -through writing a number string "x" to the 'level' proc file which is +The actual debug level can be changed with the help of the debugfs-filesystem +through writing a number string "x" to the 'level' debugfs file which is provided for every debug log. Debugging can be switched off completely -by using "-" on the 'level' proc file. +by using "-" on the 'level' debugfs file. Example: -> echo "-" > /proc/s390dbf/dasd/level +> echo "-" > /sys/kernel/debug/s390dbf/dasd/level It is also possible to deactivate the debug feature globally for every debug log. You can change the behavior using 2 sysctl parameters in @@ -99,11 +101,11 @@ Kernel Interfaces: ------------------ ---------------------------------------------------------------------------- -debug_info_t *debug_register(char *name, int pages_index, int nr_areas, +debug_info_t *debug_register(char *name, int pages, int nr_areas, int buf_size); -Parameter: name: Name of debug log (e.g. used for proc entry) - pages_index: 2^pages_index pages will be allocated per area +Parameter: name: Name of debug log (e.g. used for debugfs entry) + pages: number of pages, which will be allocated per area nr_areas: number of debug areas buf_size: size of data area in each debug entry @@ -134,7 +136,7 @@ Return Value: none Description: Sets new actual debug level if new_level is valid. --------------------------------------------------------------------------- -+void debug_stop_all(void); +void debug_stop_all(void); Parameter: none @@ -270,7 +272,7 @@ Parameter: id: handle for debug log Return Value: 0 : ok < 0: Error -Description: registers new debug view and creates proc dir entry +Description: registers new debug view and creates debugfs dir entry --------------------------------------------------------------------------- int debug_unregister_view (debug_info_t * id, struct debug_view *view); @@ -281,7 +283,7 @@ Parameter: id: handle for debug log Return Value: 0 : ok < 0: Error -Description: unregisters debug view and removes proc dir entry +Description: unregisters debug view and removes debugfs dir entry @@ -308,7 +310,7 @@ static int init(void) { /* register 4 debug areas with one page each and 4 byte data field */ - debug_info = debug_register ("test", 0, 4, 4 ); + debug_info = debug_register ("test", 1, 4, 4 ); debug_register_view(debug_info,&debug_hex_ascii_view); debug_register_view(debug_info,&debug_raw_view); @@ -343,7 +345,7 @@ static int init(void) /* register 4 debug areas with one page each and data field for */ /* format string pointer + 2 varargs (= 3 * sizeof(long)) */ - debug_info = debug_register ("test", 0, 4, sizeof(long) * 3); + debug_info = debug_register ("test", 1, 4, sizeof(long) * 3); debug_register_view(debug_info,&debug_sprintf_view); debug_sprintf_event(debug_info, 2 , "first event in %s:%i\n",__FILE__,__LINE__); @@ -362,16 +364,16 @@ module_exit(cleanup); -ProcFS Interface +Debugfs Interface ---------------- Views to the debug logs can be investigated through reading the corresponding -proc-files: +debugfs-files: Example: -> ls /proc/s390dbf/dasd -flush hex_ascii level raw -> cat /proc/s390dbf/dasd/hex_ascii | sort +1 +> ls /sys/kernel/debug/s390dbf/dasd +flush hex_ascii level pages raw +> cat /sys/kernel/debug/s390dbf/dasd/hex_ascii | sort +1 00 00974733272:680099 2 - 02 0006ad7e 07 ea 4a 90 | .... 00 00974733272:682210 2 - 02 0006ade6 46 52 45 45 | FREE 00 00974733272:682213 2 - 02 0006adf6 07 ea 4a 90 | .... @@ -391,25 +393,36 @@ Changing the debug level Example: -> cat /proc/s390dbf/dasd/level +> cat /sys/kernel/debug/s390dbf/dasd/level 3 -> echo "5" > /proc/s390dbf/dasd/level -> cat /proc/s390dbf/dasd/level +> echo "5" > /sys/kernel/debug/s390dbf/dasd/level +> cat /sys/kernel/debug/s390dbf/dasd/level 5 Flushing debug areas -------------------- Debug areas can be flushed with piping the number of the desired -area (0...n) to the proc file "flush". When using "-" all debug areas +area (0...n) to the debugfs file "flush". When using "-" all debug areas are flushed. Examples: 1. Flush debug area 0: -> echo "0" > /proc/s390dbf/dasd/flush +> echo "0" > /sys/kernel/debug/s390dbf/dasd/flush 2. Flush all debug areas: -> echo "-" > /proc/s390dbf/dasd/flush +> echo "-" > /sys/kernel/debug/s390dbf/dasd/flush + +Changing the size of debug areas +------------------------------------ +It is possible the change the size of debug areas through piping +the number of pages to the debugfs file "pages". The resize request will +also flush the debug areas. + +Example: + +Define 4 pages for the debug areas of debug feature "dasd": +> echo "4" > /sys/kernel/debug/s390dbf/dasd/pages Stooping the debug feature -------------------------- @@ -491,7 +504,7 @@ Defining views -------------- Views are specified with the 'debug_view' structure. There are defined -callback functions which are used for reading and writing the proc files: +callback functions which are used for reading and writing the debugfs files: struct debug_view { char name[DEBUG_MAX_PROCF_LEN]; @@ -525,7 +538,7 @@ typedef int (debug_input_proc_t) (debug_info_t* id, The "private_data" member can be used as pointer to view specific data. It is not used by the debug feature itself. -The output when reading a debug-proc file is structured like this: +The output when reading a debugfs file is structured like this: "prolog_proc output" @@ -534,13 +547,13 @@ The output when reading a debug-proc file is structured like this: "header_proc output 3" "format_proc output 3" ... -When a view is read from the proc fs, the Debug Feature calls the +When a view is read from the debugfs, the Debug Feature calls the 'prolog_proc' once for writing the prolog. Then 'header_proc' and 'format_proc' are called for each existing debug entry. The input_proc can be used to implement functionality when it is written to -the view (e.g. like with 'echo "0" > /proc/s390dbf/dasd/level). +the view (e.g. like with 'echo "0" > /sys/kernel/debug/s390dbf/dasd/level). For header_proc there can be used the default function debug_dflt_header_fn() which is defined in in debug.h. @@ -602,7 +615,7 @@ debug_info = debug_register ("test", 0, 4, 4 )); debug_register_view(debug_info, &debug_test_view); for(i = 0; i < 10; i ++) debug_int_event(debug_info, 1, i); -> cat /proc/s390dbf/test/myview +> cat /sys/kernel/debug/s390dbf/test/myview 00 00964419734:611402 1 - 00 88042ca This error........... 00 00964419734:611405 1 - 00 88042ca That error........... 00 00964419734:611408 1 - 00 88042ca Problem.............. -- cgit v1.2.2 From 85d7b94981e2e919697bc235aad7367b33c3864b Mon Sep 17 00:00:00 2001 From: Dinakar Guniguntala Date: Sat, 25 Jun 2005 14:57:34 -0700 Subject: [PATCH] Dynamic sched domains: cpuset changes Adds the core update_cpu_domains code and updated cpusets documentation Signed-off-by: Dinakar Guniguntala Acked-by: Paul Jackson Acked-by: Nick Piggin Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/cpusets.txt | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'Documentation') diff --git a/Documentation/cpusets.txt b/Documentation/cpusets.txt index 2f8f24eaefd9..ad944c060312 100644 --- a/Documentation/cpusets.txt +++ b/Documentation/cpusets.txt @@ -51,6 +51,14 @@ mems_allowed vector. If a cpuset is cpu or mem exclusive, no other cpuset, other than a direct ancestor or descendent, may share any of the same CPUs or Memory Nodes. +A cpuset that is cpu exclusive has a sched domain associated with it. +The sched domain consists of all cpus in the current cpuset that are not +part of any exclusive child cpusets. +This ensures that the scheduler load balacing code only balances +against the cpus that are in the sched domain as defined above and not +all of the cpus in the system. This removes any overhead due to +load balancing code trying to pull tasks outside of the cpu exclusive +cpuset only to be prevented by the tasks' cpus_allowed mask. User level code may create and destroy cpusets by name in the cpuset virtual file system, manage the attributes and permissions of these @@ -84,6 +92,9 @@ This can be especially valuable on: and a database), or * NUMA systems running large HPC applications with demanding performance characteristics. + * Also cpu_exclusive cpusets are useful for servers running orthogonal + workloads such as RT applications requiring low latency and HPC + applications that are throughput sensitive These subsets, or "soft partitions" must be able to be dynamically adjusted, as the job mix changes, without impacting other concurrently @@ -125,6 +136,8 @@ Cpusets extends these two mechanisms as follows: - A cpuset may be marked exclusive, which ensures that no other cpuset (except direct ancestors and descendents) may contain any overlapping CPUs or Memory Nodes. + Also a cpu_exclusive cpuset would be associated with a sched + domain. - You can list all the tasks (by pid) attached to any cpuset. The implementation of cpusets requires a few, simple hooks @@ -136,6 +149,9 @@ into the rest of the kernel, none in performance critical paths: allowed in that tasks cpuset. - in sched.c migrate_all_tasks(), to keep migrating tasks within the CPUs allowed by their cpuset, if possible. + - in sched.c, a new API partition_sched_domains for handling + sched domain changes associated with cpu_exclusive cpusets + and related changes in both sched.c and arch/ia64/kernel/domain.c - in the mbind and set_mempolicy system calls, to mask the requested Memory Nodes by what's allowed in that tasks cpuset. - in page_alloc, to restrict memory to allowed nodes. -- cgit v1.2.2 From dc009d92435f99498cbc579ce76bf28e837e2c14 Mon Sep 17 00:00:00 2001 From: "Eric W. Biederman" Date: Sat, 25 Jun 2005 14:57:52 -0700 Subject: [PATCH] kexec: add kexec syscalls This patch introduces the architecture independent implementation the sys_kexec_load, the compat_sys_kexec_load system calls. Kexec on panic support has been integrated into the core patch and is relatively clean. In addition the hopefully architecture independent option crashkernel=size@location has been docuemented. It's purpose is to reserve space for the panic kernel to live, and where no DMA transfer will ever be setup to access. Signed-off-by: Eric Biederman Signed-off-by: Alexander Nyberg Signed-off-by: Adrian Bunk Signed-off-by: Vivek Goyal Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/kernel-parameters.txt | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'Documentation') diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 86db43fd6b0f..560ff5ae3fd9 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -358,6 +358,10 @@ running once the system is up. cpia_pp= [HW,PPT] Format: { parport | auto | none } + crashkernel=nn[KMG]@ss[KMG] + [KNL] Reserve a chunk of physical memory to + hold a kernel to switch to with kexec on panic. + cs4232= [HW,OSS] Format: ,,,,, -- cgit v1.2.2 From b089f4a68eccd9782c89262c0d7cae146d5a8a40 Mon Sep 17 00:00:00 2001 From: Vivek Goyal Date: Sat, 25 Jun 2005 14:58:15 -0700 Subject: [PATCH] kdump: Documentation for Kdump This patch contains the documentation for the kexec based crash dump tool. Quick kdump-howto ================================================================ 1) Download and build kexec-tools. 2) Download and build the latest kexec/kdump (-mm) kernel patchset. Two kernels need to be built in order to get this feature working. A) First kernel: a) Enable "kexec system call" feature: CONFIG_KEXEC=y b) Physical load address (use default): CONFIG_PHYSICAL_START=0x100000 c) Enable "sysfs file system support": CONFIG_SYSFS=y d) Boot into first kernel with the command line parameter "crashkernel=Y@X": For example: "crashkernel=64M@16M". B) Second kernel: a) Enable "kernel crash dumps" feature: CONFIG_CRASH_DUMP=y b) Physical load addreess, use same load address as X in "crashkernel" kernel parameter in d) above, e.g., 16 MB or 0x1000000. CONFIG_PHYSICAL_START=0x1000000 c) Enable "/proc/vmcore support" (Optional, in Pseudo filesystems). CONFIG_PROC_VMCORE=y 3) Boot into the first kernel. 4) Load the second kernel to be booted using: kexec -p --crash-dump --args-linux --append="root= maxcpus=1 init 1" 5) System reboots into the second kernel when a panic occurs. A module can be written to force the panic, for testing purposes. 6) See Documentation/kdump.txt for how to read the first kernel's memory image and how to analyze it. Signed-off-by: Hariprasad Nellitheertha Signed-off-by: Eric Biederman Signed-off-by: Vivek Goyal Signed-off-by: randy_dunlap Signed-off-by: Maneesh Soni Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/00-INDEX | 2 + Documentation/kdump/gdbmacros.txt | 179 ++++++++++++++++++++++++++++++++++++++ Documentation/kdump/kdump.txt | 135 ++++++++++++++++++++++++++++ 3 files changed, 316 insertions(+) create mode 100644 Documentation/kdump/gdbmacros.txt create mode 100644 Documentation/kdump/kdump.txt (limited to 'Documentation') diff --git a/Documentation/00-INDEX b/Documentation/00-INDEX index 8de8a01a2474..f28a24e0279b 100644 --- a/Documentation/00-INDEX +++ b/Documentation/00-INDEX @@ -138,6 +138,8 @@ java.txt - info on the in-kernel binary support for Java(tm). kbuild/ - directory with info about the kernel build process. +kdumpt.txt + - mini HowTo on getting the crash dump code to work. kernel-doc-nano-HOWTO.txt - mini HowTo on generation and location of kernel documentation files. kernel-docs.txt diff --git a/Documentation/kdump/gdbmacros.txt b/Documentation/kdump/gdbmacros.txt new file mode 100644 index 000000000000..bc1b9eb92ae1 --- /dev/null +++ b/Documentation/kdump/gdbmacros.txt @@ -0,0 +1,179 @@ +# +# This file contains a few gdb macros (user defined commands) to extract +# useful information from kernel crashdump (kdump) like stack traces of +# all the processes or a particular process and trapinfo. +# +# These macros can be used by copying this file in .gdbinit (put in home +# directory or current directory) or by invoking gdb command with +# --command= option +# +# Credits: +# Alexander Nyberg +# V Srivatsa +# Maneesh Soni +# + +define bttnobp + set $tasks_off=((size_t)&((struct task_struct *)0)->tasks) + set $pid_off=((size_t)&((struct task_struct *)0)->pids[1].pid_list.next) + set $init_t=&init_task + set $next_t=(((char *)($init_t->tasks).next) - $tasks_off) + while ($next_t != $init_t) + set $next_t=(struct task_struct *)$next_t + printf "\npid %d; comm %s:\n", $next_t.pid, $next_t.comm + printf "===================\n" + set var $stackp = $next_t.thread.esp + set var $stack_top = ($stackp & ~4095) + 4096 + + while ($stackp < $stack_top) + if (*($stackp) > _stext && *($stackp) < _sinittext) + info symbol *($stackp) + end + set $stackp += 4 + end + set $next_th=(((char *)$next_t->pids[1].pid_list.next) - $pid_off) + while ($next_th != $next_t) + set $next_th=(struct task_struct *)$next_th + printf "\npid %d; comm %s:\n", $next_t.pid, $next_t.comm + printf "===================\n" + set var $stackp = $next_t.thread.esp + set var $stack_top = ($stackp & ~4095) + 4096 + + while ($stackp < $stack_top) + if (*($stackp) > _stext && *($stackp) < _sinittext) + info symbol *($stackp) + end + set $stackp += 4 + end + set $next_th=(((char *)$next_th->pids[1].pid_list.next) - $pid_off) + end + set $next_t=(char *)($next_t->tasks.next) - $tasks_off + end +end +document bttnobp + dump all thread stack traces on a kernel compiled with !CONFIG_FRAME_POINTER +end + +define btt + set $tasks_off=((size_t)&((struct task_struct *)0)->tasks) + set $pid_off=((size_t)&((struct task_struct *)0)->pids[1].pid_list.next) + set $init_t=&init_task + set $next_t=(((char *)($init_t->tasks).next) - $tasks_off) + while ($next_t != $init_t) + set $next_t=(struct task_struct *)$next_t + printf "\npid %d; comm %s:\n", $next_t.pid, $next_t.comm + printf "===================\n" + set var $stackp = $next_t.thread.esp + set var $stack_top = ($stackp & ~4095) + 4096 + set var $stack_bot = ($stackp & ~4095) + + set $stackp = *($stackp) + while (($stackp < $stack_top) && ($stackp > $stack_bot)) + set var $addr = *($stackp + 4) + info symbol $addr + set $stackp = *($stackp) + end + + set $next_th=(((char *)$next_t->pids[1].pid_list.next) - $pid_off) + while ($next_th != $next_t) + set $next_th=(struct task_struct *)$next_th + printf "\npid %d; comm %s:\n", $next_t.pid, $next_t.comm + printf "===================\n" + set var $stackp = $next_t.thread.esp + set var $stack_top = ($stackp & ~4095) + 4096 + set var $stack_bot = ($stackp & ~4095) + + set $stackp = *($stackp) + while (($stackp < $stack_top) && ($stackp > $stack_bot)) + set var $addr = *($stackp + 4) + info symbol $addr + set $stackp = *($stackp) + end + set $next_th=(((char *)$next_th->pids[1].pid_list.next) - $pid_off) + end + set $next_t=(char *)($next_t->tasks.next) - $tasks_off + end +end +document btt + dump all thread stack traces on a kernel compiled with CONFIG_FRAME_POINTER +end + +define btpid + set var $pid = $arg0 + set $tasks_off=((size_t)&((struct task_struct *)0)->tasks) + set $pid_off=((size_t)&((struct task_struct *)0)->pids[1].pid_list.next) + set $init_t=&init_task + set $next_t=(((char *)($init_t->tasks).next) - $tasks_off) + set var $pid_task = 0 + + while ($next_t != $init_t) + set $next_t=(struct task_struct *)$next_t + + if ($next_t.pid == $pid) + set $pid_task = $next_t + end + + set $next_th=(((char *)$next_t->pids[1].pid_list.next) - $pid_off) + while ($next_th != $next_t) + set $next_th=(struct task_struct *)$next_th + if ($next_th.pid == $pid) + set $pid_task = $next_th + end + set $next_th=(((char *)$next_th->pids[1].pid_list.next) - $pid_off) + end + set $next_t=(char *)($next_t->tasks.next) - $tasks_off + end + + printf "\npid %d; comm %s:\n", $pid_task.pid, $pid_task.comm + printf "===================\n" + set var $stackp = $pid_task.thread.esp + set var $stack_top = ($stackp & ~4095) + 4096 + set var $stack_bot = ($stackp & ~4095) + + set $stackp = *($stackp) + while (($stackp < $stack_top) && ($stackp > $stack_bot)) + set var $addr = *($stackp + 4) + info symbol $addr + set $stackp = *($stackp) + end +end +document btpid + backtrace of pid +end + + +define trapinfo + set var $pid = $arg0 + set $tasks_off=((size_t)&((struct task_struct *)0)->tasks) + set $pid_off=((size_t)&((struct task_struct *)0)->pids[1].pid_list.next) + set $init_t=&init_task + set $next_t=(((char *)($init_t->tasks).next) - $tasks_off) + set var $pid_task = 0 + + while ($next_t != $init_t) + set $next_t=(struct task_struct *)$next_t + + if ($next_t.pid == $pid) + set $pid_task = $next_t + end + + set $next_th=(((char *)$next_t->pids[1].pid_list.next) - $pid_off) + while ($next_th != $next_t) + set $next_th=(struct task_struct *)$next_th + if ($next_th.pid == $pid) + set $pid_task = $next_th + end + set $next_th=(((char *)$next_th->pids[1].pid_list.next) - $pid_off) + end + set $next_t=(char *)($next_t->tasks.next) - $tasks_off + end + + printf "Trapno %ld, cr2 0x%lx, error_code %ld\n", $pid_task.thread.trap_no, \ + $pid_task.thread.cr2, $pid_task.thread.error_code + +end +document trapinfo + Run info threads and lookup pid of thread #1 + 'trapinfo ' will tell you by which trap & possibly + addresthe kernel paniced. +end diff --git a/Documentation/kdump/kdump.txt b/Documentation/kdump/kdump.txt new file mode 100644 index 000000000000..b0f412e42791 --- /dev/null +++ b/Documentation/kdump/kdump.txt @@ -0,0 +1,135 @@ +Documentation for kdump - the kexec-based crash dumping solution +================================================================ + +DESIGN +====== + +Kdump uses kexec to reboot to a second kernel whenever a dump needs to be taken. +This second kernel is booted with very little memory. The first kernel reserves +the section of memory that the second kernel uses. This ensures that on-going +DMA from the first kernel does not corrupt the second kernel. + +All the necessary information about Core image is encoded in ELF format and +stored in reserved area of memory before crash. Physical address of start of +ELF header is passed to new kernel through command line parameter elfcorehdr=. + +On i386, the first 640 KB of physical memory is needed to boot, irrespective +of where the kernel loads. Hence, this region is backed up by kexec just before +rebooting into the new kernel. + +In the second kernel, "old memory" can be accessed in two ways. + +- The first one is through a /dev/oldmem device interface. A capture utility + can read the device file and write out the memory in raw format. This is raw + dump of memory and analysis/capture tool should be intelligent enough to + determine where to look for the right information. ELF headers (elfcorehdr=) + can become handy here. + +- The second interface is through /proc/vmcore. This exports the dump as an ELF + format file which can be written out using any file copy command + (cp, scp, etc). Further, gdb can be used to perform limited debugging on + the dump file. This method ensures methods ensure that there is correct + ordering of the dump pages (corresponding to the first 640 KB that has been + relocated). + +SETUP +===== + +1) Download http://www.xmission.com/~ebiederm/files/kexec/kexec-tools-1.101.tar.gz + and apply http://lse.sourceforge.net/kdump/patches/kexec-tools-1.101-kdump.patch + and after that build the source. + +2) Download and build the appropriate (latest) kexec/kdump (-mm) kernel + patchset and apply it to the vanilla kernel tree. + + Two kernels need to be built in order to get this feature working. + + A) First kernel: + a) Enable "kexec system call" feature (in Processor type and features). + CONFIG_KEXEC=y + b) This kernel's physical load address should be the default value of + 0x100000 (0x100000, 1 MB) (in Processor type and features). + CONFIG_PHYSICAL_START=0x100000 + c) Enable "sysfs file system support" (in Pseudo filesystems). + CONFIG_SYSFS=y + d) Boot into first kernel with the command line parameter "crashkernel=Y@X". + Use appropriate values for X and Y. Y denotes how much memory to reserve + for the second kernel, and X denotes at what physical address the reserved + memory section starts. For example: "crashkernel=64M@16M". + + B) Second kernel: + a) Enable "kernel crash dumps" feature (in Processor type and features). + CONFIG_CRASH_DUMP=y + b) Specify a suitable value for "Physical address where the kernel is + loaded" (in Processor type and features). Typically this value + should be same as X (See option d) above, e.g., 16 MB or 0x1000000. + CONFIG_PHYSICAL_START=0x1000000 + c) Enable "/proc/vmcore support" (Optional, in Pseudo filesystems). + CONFIG_PROC_VMCORE=y + + Note: Options a) and b) depend upon "Configure standard kernel features + (for small systems)" (under General setup). + Option a) also depends on CONFIG_HIGHMEM (under Processor + type and features). + Both option a) and b) are under "Processor type and features". + +3) Boot into the first kernel. You are now ready to try out kexec-based crash + dumps. + +4) Load the second kernel to be booted using: + + kexec -p --crash-dump --args-linux --append="root= + maxcpus=1 init 1" + + Note: i) has to be a vmlinux image. bzImage will not work, + as of now. + ii) By default ELF headers are stored in ELF32 format (for i386). This + is sufficient to represent the physical memory up to 4GB. To store + headers in ELF64 format, specifiy "--elf64-core-headers" on the + kexec command line additionally. + iii) For now (or until it is fixed), it's best to build the + second-kernel without multi-processor support, i.e., make it + a uniprocessor kernel. + +5) System reboots into the second kernel when a panic occurs. A module can be + written to force the panic, for testing purposes. + +6) Write out the dump file using + + cp /proc/vmcore + + Dump memory can also be accessed as a /dev/oldmem device for a linear/raw + view. To create the device, type: + + mknod /dev/oldmem c 1 12 + + Use "dd" with suitable options for count, bs and skip to access specific + portions of the dump. + + Entire memory: dd if=/dev/oldmem of=oldmem.001 + +ANALYSIS +======== + +Limited analysis can be done using gdb on the dump file copied out of +/proc/vmcore. Use vmlinux built with -g and run + + gdb vmlinux + +Stack trace for the task on processor 0, register display, memory display +work fine. + +Note: gdb cannot analyse core files generated in ELF64 format for i386. + +TODO +==== + +1) Provide a kernel pages filtering mechanism so that core file size is not + insane on systems having huge memory banks. +2) Modify "crash" tool to make it recognize this dump. + +CONTACT +======= + +Hariprasad Nellitheertha - hari at in dot ibm dot com +Vivek Goyal (vgoyal@in.ibm.com) -- cgit v1.2.2 From d58831e4163699de204dea199be2e903bf5d6eff Mon Sep 17 00:00:00 2001 From: Vivek Goyal Date: Sat, 25 Jun 2005 14:58:17 -0700 Subject: [PATCH] kdump documentation update to introduce use of irqpoll o Specify "irqpoll" command line option which loading second kernel. This helps in reducing driver initialization failures in second kernel due to shared interrupts. o Enabled LAPIC/IOAPIC support for UP kernels in second kernel. This reduces the chances of devices sharing the irq and hence reduces the chances of driver initialization failures in second kernel. o Build a UP capture kernel and disabled SMP support. Signed-off-by: Vivek Goyal Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/kdump/kdump.txt | 28 +++++++++++++++++----------- 1 file changed, 17 insertions(+), 11 deletions(-) (limited to 'Documentation') diff --git a/Documentation/kdump/kdump.txt b/Documentation/kdump/kdump.txt index b0f412e42791..7ff213f4becd 100644 --- a/Documentation/kdump/kdump.txt +++ b/Documentation/kdump/kdump.txt @@ -66,12 +66,18 @@ SETUP CONFIG_PHYSICAL_START=0x1000000 c) Enable "/proc/vmcore support" (Optional, in Pseudo filesystems). CONFIG_PROC_VMCORE=y - - Note: Options a) and b) depend upon "Configure standard kernel features - (for small systems)" (under General setup). - Option a) also depends on CONFIG_HIGHMEM (under Processor + d) Disable SMP support and build a UP kernel (Until it is fixed). + CONFIG_SMP=n + e) Enable "Local APIC support on uniprocessors". + CONFIG_X86_UP_APIC=y + f) Enable "IO-APIC support on uniprocessors" + CONFIG_X86_UP_IOAPIC=y + + Note: i) Options a) and b) depend upon "Configure standard kernel features + (for small systems)" (under General setup). + ii) Option a) also depends on CONFIG_HIGHMEM (under Processor type and features). - Both option a) and b) are under "Processor type and features". + iii) Both option a) and b) are under "Processor type and features". 3) Boot into the first kernel. You are now ready to try out kexec-based crash dumps. @@ -79,7 +85,7 @@ SETUP 4) Load the second kernel to be booted using: kexec -p --crash-dump --args-linux --append="root= - maxcpus=1 init 1" + init 1 irqpoll" Note: i) has to be a vmlinux image. bzImage will not work, as of now. @@ -87,12 +93,12 @@ SETUP is sufficient to represent the physical memory up to 4GB. To store headers in ELF64 format, specifiy "--elf64-core-headers" on the kexec command line additionally. - iii) For now (or until it is fixed), it's best to build the - second-kernel without multi-processor support, i.e., make it - a uniprocessor kernel. + iii) Specify "irqpoll" as command line parameter. This reduces driver + initialization failures in second kernel due to shared interrupts. 5) System reboots into the second kernel when a panic occurs. A module can be - written to force the panic, for testing purposes. + written to force the panic or "ALT-SysRq-c" can be used initiate a crash + dump for testing purposes. 6) Write out the dump file using @@ -131,5 +137,5 @@ TODO CONTACT ======= -Hariprasad Nellitheertha - hari at in dot ibm dot com Vivek Goyal (vgoyal@in.ibm.com) +Maneesh Soni (maneesh@in.ibm.com) -- cgit v1.2.2 From 2030eae52b416a9a9f0ffda74c982b7f1e19496d Mon Sep 17 00:00:00 2001 From: Vivek Goyal Date: Sat, 25 Jun 2005 14:58:20 -0700 Subject: [PATCH] Retrieve elfcorehdr address from command line This patch adds support for retrieving the address of elf core header if one is passed in command line. Signed-off-by: Vivek Goyal Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/kernel-parameters.txt | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'Documentation') diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 560ff5ae3fd9..f44bb5567c5b 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -451,6 +451,10 @@ running once the system is up. Format: {"as"|"cfq"|"deadline"|"noop"} See Documentation/block/as-iosched.txt and Documentation/block/deadline-iosched.txt for details. + elfcorehdr= [IA-32] + Specifies physical address of start of kernel core image + elf header. + See Documentation/kdump.txt for details. enforcing [SELINUX] Set initial enforcing status. Format: {"0" | "1"} -- cgit v1.2.2 From 50b1fdbd81edcc8bd343ca44aca2b87a29e2f15c Mon Sep 17 00:00:00 2001 From: Vivek Goyal Date: Sat, 25 Jun 2005 14:58:23 -0700 Subject: [PATCH] kdump: Accessing dump file in linear raw format (/dev/oldmem) Hariprasad Nellitheertha This patch contains the code that enables us to access the previous kernel's memory as /dev/oldmem. Signed-off-by: Eric Biederman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/devices.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation') diff --git a/Documentation/devices.txt b/Documentation/devices.txt index bb67cf25010e..0f515175c72a 100644 --- a/Documentation/devices.txt +++ b/Documentation/devices.txt @@ -94,6 +94,7 @@ Your cooperation is appreciated. 9 = /dev/urandom Faster, less secure random number gen. 10 = /dev/aio Asyncronous I/O notification interface 11 = /dev/kmsg Writes to this come out as printk's + 12 = /dev/oldmem Access to crash dump from kexec kernel 1 block RAM disk 0 = /dev/ram0 First RAM disk 1 = /dev/ram1 Second RAM disk -- cgit v1.2.2 From 86b1ae38c0a62409dc862a28e3f08920f55f944b Mon Sep 17 00:00:00 2001 From: Hariprasad Nellitheertha Date: Sat, 25 Jun 2005 14:58:25 -0700 Subject: [PATCH] kdump: sysrq trigger mechanism for kexec based crashdumps Add a sysrq-trigger mechanism for kexec based crashdumps. Alt-Sysrq-c triggers a kexec based crashdump. Signed-off-by: Hariprasad Nellitheertha Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/sysrq.txt | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'Documentation') diff --git a/Documentation/sysrq.txt b/Documentation/sysrq.txt index f98c2e31c143..136d817c01ba 100644 --- a/Documentation/sysrq.txt +++ b/Documentation/sysrq.txt @@ -72,6 +72,8 @@ On all - write a character to /proc/sysrq-trigger. eg: 'b' - Will immediately reboot the system without syncing or unmounting your disks. +'c' - Will perform a kexec reboot in order to take a crashdump. + 'o' - Will shut your system off (if configured and supported). 's' - Will attempt to sync all mounted filesystems. @@ -122,6 +124,9 @@ useful when you want to exit a program that will not let you switch consoles. re'B'oot is good when you're unable to shut down. But you should also 'S'ync and 'U'mount first. +'C'rashdump can be used to manually trigger a crashdump when the system is hung. +The kernel needs to have been built with CONFIG_KEXEC enabled. + 'S'ync is great when your system is locked up, it allows you to sync your disks and will certainly lessen the chance of data loss and fscking. Note that the sync hasn't taken place until you see the "OK" and "Done" appear -- cgit v1.2.2 From 594dd2c98101a5dc279153ec806d554e6b8a1e35 Mon Sep 17 00:00:00 2001 From: Nico Golde Date: Sat, 25 Jun 2005 14:58:33 -0700 Subject: [PATCH] cpufreq: governors documentation fixes I corrected a small error and enhanced the govenor.txt file with the ondemand daemon because the kernel configs link to the documentation but ondemand wasn't documentated. Feel free to include the patch in the attachment. Cc: Dominik Brodowski Cc: Dave Jones Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/cpu-freq/governors.txt | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) (limited to 'Documentation') diff --git a/Documentation/cpu-freq/governors.txt b/Documentation/cpu-freq/governors.txt index b85481acd0ca..933fae74c337 100644 --- a/Documentation/cpu-freq/governors.txt +++ b/Documentation/cpu-freq/governors.txt @@ -9,6 +9,7 @@ Dominik Brodowski + some additions and corrections by Nico Golde @@ -25,6 +26,7 @@ Contents: 2.1 Performance 2.2 Powersave 2.3 Userspace +2.4 Ondemand 3. The Governor Interface in the CPUfreq Core @@ -86,7 +88,7 @@ highest frequency within the borders of scaling_min_freq and scaling_max_freq. -2.1 Powersave +2.2 Powersave ------------- The CPUfreq governor "powersave" sets the CPU statically to the @@ -94,7 +96,7 @@ lowest frequency within the borders of scaling_min_freq and scaling_max_freq. -2.2 Userspace +2.3 Userspace ------------- The CPUfreq governor "userspace" allows the user, or any userspace @@ -103,6 +105,14 @@ by making a sysfs file "scaling_setspeed" available in the CPU-device directory. +2.4 Ondemand +------------ + +The CPUfreq govenor "ondemand" sets the CPU depending on the +current usage. To do this the CPU must have the capability to +switch the frequency very fast. + + 3. The Governor Interface in the CPUfreq Core ============================================= -- cgit v1.2.2 From a1ae13a4dd1ad732f6fb55a55dec93524feca8bc Mon Sep 17 00:00:00 2001 From: Jesper Juhl Date: Sat, 25 Jun 2005 14:59:01 -0700 Subject: [PATCH] cosmetic fixes for example programs in Documentation/cdrom/sbpcd This patch makes a few minor changes to the example programs in Documentation/cdrom/sbpcd to kill off some warnings and build failures. Signed-off-by: Jesper Juhl Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/cdrom/sbpcd | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) (limited to 'Documentation') diff --git a/Documentation/cdrom/sbpcd b/Documentation/cdrom/sbpcd index d1825dffca34..b3ba63f4ce3e 100644 --- a/Documentation/cdrom/sbpcd +++ b/Documentation/cdrom/sbpcd @@ -419,6 +419,7 @@ into the file "track01": */ #include #include +#include #include static struct cdrom_tochdr hdr; @@ -429,7 +430,7 @@ static int datafile, drive; static int i, j, limit, track, err; static char filename[32]; -main(int argc, char *argv[]) +int main(int argc, char *argv[]) { /* * open /dev/cdrom @@ -516,6 +517,7 @@ entry[track+1].cdte_addr.lba=entry[track].cdte_addr.lba+300; } arg.addr.lba++; } + return 0; } /*===================== end program ========================================*/ @@ -564,15 +566,16 @@ Appendix -- the "cdtester" utility: #include #include #include +#include #include #ifdef AZT_PRIVATE_IOCTLS #include -#endif AZT_PRIVATE_IOCTLS +#endif /* AZT_PRIVATE_IOCTLS */ #ifdef SBP_PRIVATE_IOCTLS #include #include -#endif SBP_PRIVATE_IOCTLS +#endif /* SBP_PRIVATE_IOCTLS */ struct cdrom_tochdr hdr; struct cdrom_tochdr tocHdr; @@ -590,7 +593,7 @@ union struct cdrom_msf msf; unsigned char buf[CD_FRAMESIZE_RAW]; } azt; -#endif AZT_PRIVATE_IOCTLS +#endif /* AZT_PRIVATE_IOCTLS */ int i, i1, i2, i3, j, k; unsigned char sequence=0; unsigned char command[80]; @@ -738,7 +741,7 @@ void display(int size,unsigned char *buffer) } } -main(int argc, char *argv[]) +int main(int argc, char *argv[]) { printf("\nTesting tool for a CDROM driver's audio functions V0.1\n"); printf("(C) 1995 Eberhard Moenkeberg \n"); @@ -1046,12 +1049,13 @@ main(int argc, char *argv[]) rc=ioctl(drive,CDROMAUDIOBUFSIZ,j); printf("%d frames granted.\n",rc); break; -#endif SBP_PRIVATE_IOCTLS +#endif /* SBP_PRIVATE_IOCTLS */ default: printf("unknown command: \"%s\".\n",command); break; } } + return 0; } /*==========================================================================*/ -- cgit v1.2.2 From 301a716446a8b24898808d0430c2ed0dce55890e Mon Sep 17 00:00:00 2001 From: Tobias Klauser Date: Sat, 25 Jun 2005 14:59:29 -0700 Subject: [PATCH] Remove duplicate file in Documentation/networking (00-INDEX) wanpipe.txt and wan-router.txt in Documentation/networking contain the exact same information (diff between the two shows no Documentation/networking/00-INDEX as pointed out by Randy Dunlap. Signed-off-by: Tobias Klauser Signed-off-by: Domen Puncer Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/networking/00-INDEX | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'Documentation') diff --git a/Documentation/networking/00-INDEX b/Documentation/networking/00-INDEX index 834993d26730..5b01d5cc4e95 100644 --- a/Documentation/networking/00-INDEX +++ b/Documentation/networking/00-INDEX @@ -114,9 +114,7 @@ tuntap.txt vortex.txt - info on using 3Com Vortex (3c590, 3c592, 3c595, 3c597) Ethernet cards. wan-router.txt - - Wan router documentation -wanpipe.txt - - WANPIPE(tm) Multiprotocol WAN Driver for Linux WAN Router + - WAN router documentation wavelan.txt - AT&T GIS (nee NCR) WaveLAN card: An Ethernet-like radio transceiver x25.txt -- cgit v1.2.2 From f353488ce48e7a0311fe764284096481b455fbe9 Mon Sep 17 00:00:00 2001 From: Tobias Klauser Date: Sat, 25 Jun 2005 14:59:30 -0700 Subject: [PATCH] Remove duplicate file in Documentation/networking The files wanpipe.txt and wan-router.txt in Documentation/networking contain the exact same information (diff between the two shows no document is "Linux WAN Router Utilities Package" and therefor the name wan-router.txt is more appropriate. Signed-off-by: Tobias Klauser Signed-off-by: Domen Puncer Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/networking/wanpipe.txt | 622 ----------------------------------- 1 file changed, 622 deletions(-) delete mode 100644 Documentation/networking/wanpipe.txt (limited to 'Documentation') diff --git a/Documentation/networking/wanpipe.txt b/Documentation/networking/wanpipe.txt deleted file mode 100644 index aea20cd2a56e..000000000000 --- a/Documentation/networking/wanpipe.txt +++ /dev/null @@ -1,622 +0,0 @@ ------------------------------------------------------------------------------- -Linux WAN Router Utilities Package ------------------------------------------------------------------------------- -Version 2.2.1 -Mar 28, 2001 -Author: Nenad Corbic -Copyright (c) 1995-2001 Sangoma Technologies Inc. ------------------------------------------------------------------------------- - -INTRODUCTION - -Wide Area Networks (WANs) are used to interconnect Local Area Networks (LANs) -and/or stand-alone hosts over vast distances with data transfer rates -significantly higher than those achievable with commonly used dial-up -connections. - -Usually an external device called `WAN router' sitting on your local network -or connected to your machine's serial port provides physical connection to -WAN. Although router's job may be as simple as taking your local network -traffic, converting it to WAN format and piping it through the WAN link, these -devices are notoriously expensive, with prices as much as 2 - 5 times higher -then the price of a typical PC box. - -Alternatively, considering robustness and multitasking capabilities of Linux, -an internal router can be built (most routers use some sort of stripped down -Unix-like operating system anyway). With a number of relatively inexpensive WAN -interface cards available on the market, a perfectly usable router can be -built for less than half a price of an external router. Yet a Linux box -acting as a router can still be used for other purposes, such as fire-walling, -running FTP, WWW or DNS server, etc. - -This kernel module introduces the notion of a WAN Link Driver (WLD) to Linux -operating system and provides generic hardware-independent services for such -drivers. Why can existing Linux network device interface not be used for -this purpose? Well, it can. However, there are a few key differences between -a typical network interface (e.g. Ethernet) and a WAN link. - -Many WAN protocols, such as X.25 and frame relay, allow for multiple logical -connections (known as `virtual circuits' in X.25 terminology) over a single -physical link. Each such virtual circuit may (and almost always does) lead -to a different geographical location and, therefore, different network. As a -result, it is the virtual circuit, not the physical link, that represents a -route and, therefore, a network interface in Linux terms. - -To further complicate things, virtual circuits are usually volatile in nature -(excluding so called `permanent' virtual circuits or PVCs). With almost no -time required to set up and tear down a virtual circuit, it is highly desirable -to implement on-demand connections in order to minimize network charges. So -unlike a typical network driver, the WAN driver must be able to handle multiple -network interfaces and cope as multiple virtual circuits come into existence -and go away dynamically. - -Last, but not least, WAN configuration is much more complex than that of say -Ethernet and may well amount to several dozens of parameters. Some of them -are "link-wide" while others are virtual circuit-specific. The same holds -true for WAN statistics which is by far more extensive and extremely useful -when troubleshooting WAN connections. Extending the ifconfig utility to suit -these needs may be possible, but does not seem quite reasonable. Therefore, a -WAN configuration utility and corresponding application programmer's interface -is needed for this purpose. - -Most of these problems are taken care of by this module. Its goal is to -provide a user with more-or-less standard look and feel for all WAN devices and -assist a WAN device driver writer by providing common services, such as: - - o User-level interface via /proc file system - o Centralized configuration - o Device management (setup, shutdown, etc.) - o Network interface management (dynamic creation/destruction) - o Protocol encapsulation/decapsulation - -To ba able to use the Linux WAN Router you will also need a WAN Tools package -available from - - ftp.sangoma.com/pub/linux/current_wanpipe/wanpipe-X.Y.Z.tgz - -where vX.Y.Z represent the wanpipe version number. - -For technical questions and/or comments please e-mail to ncorbic@sangoma.com. -For general inquiries please contact Sangoma Technologies Inc. by - - Hotline: 1-800-388-2475 (USA and Canada, toll free) - Phone: (905) 474-1990 ext: 106 - Fax: (905) 474-9223 - E-mail: dm@sangoma.com (David Mandelstam) - WWW: http://www.sangoma.com - - -INSTALLATION - -Please read the WanpipeForLinux.pdf manual on how to -install the WANPIPE tools and drivers properly. - - -After installing wanpipe package: /usr/local/wanrouter/doc. -On the ftp.sangoma.com : /linux/current_wanpipe/doc - - -COPYRIGHT AND LICENSING INFORMATION - -This program is free software; you can redistribute it and/or modify it under -the terms of the GNU General Public License as published by the Free Software -Foundation; either version 2, or (at your option) any later version. - -This program is distributed in the hope that it will be useful, but WITHOUT -ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS -FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - -You should have received a copy of the GNU General Public License along with -this program; if not, write to the Free Software Foundation, Inc., 675 Mass -Ave, Cambridge, MA 02139, USA. - - - -ACKNOWLEDGEMENTS - -This product is based on the WANPIPE(tm) Multiprotocol WAN Router developed -by Sangoma Technologies Inc. for Linux 2.0.x and 2.2.x. Success of the WANPIPE -together with the next major release of Linux kernel in summer 1996 commanded -adequate changes to the WANPIPE code to take full advantage of new Linux -features. - -Instead of continuing developing proprietary interface tied to Sangoma WAN -cards, we decided to separate all hardware-independent code into a separate -module and defined two levels of interfaces - one for user-level applications -and another for kernel-level WAN drivers. WANPIPE is now implemented as a -WAN driver compliant with the WAN Link Driver interface. Also a general -purpose WAN configuration utility and a set of shell scripts was developed to -support WAN router at the user level. - -Many useful ideas concerning hardware-independent interface implementation -were given by Mike McLagan and his implementation -of the Frame Relay router and drivers for Sangoma cards (dlci/sdla). - -With the new implementation of the APIs being incorporated into the WANPIPE, -a special thank goes to Alan Cox in providing insight into BSD sockets. - -Special thanks to all the WANPIPE users who performed field-testing, reported -bugs and made valuable comments and suggestions that help us to improve this -product. - - - -NEW IN THIS RELEASE - - o Updated the WANCFG utility - Calls the pppconfig to configure the PPPD - for async connections. - - o Added the PPPCONFIG utility - Used to configure the PPPD dameon for the - WANPIPE Async PPP and standard serial port. - The wancfg calls the pppconfig to configure - the pppd. - - o Fixed the PCI autodetect feature. - The SLOT 0 was used as an autodetect option - however, some high end PC's slot numbers start - from 0. - - o This release has been tested with the new backupd - daemon release. - - -PRODUCT COMPONENTS AND RELATED FILES - -/etc: (or user defined) - wanpipe1.conf default router configuration file - -/lib/modules/X.Y.Z/misc: - wanrouter.o router kernel loadable module - af_wanpipe.o wanpipe api socket module - -/lib/modules/X.Y.Z/net: - sdladrv.o Sangoma SDLA support module - wanpipe.o Sangoma WANPIPE(tm) driver module - -/proc/net/wanrouter - Config reads current router configuration - Status reads current router status - {name} reads WAN driver statistics - -/usr/sbin: - wanrouter wanrouter start-up script - wanconfig wanrouter configuration utility - sdladump WANPIPE adapter memory dump utility - fpipemon Monitor for Frame Relay - cpipemon Monitor for Cisco HDLC - ppipemon Monitor for PPP - xpipemon Monitor for X25 - wpkbdmon WANPIPE keyboard led monitor/debugger - -/usr/local/wanrouter: - README this file - COPYING GNU General Public License - Setup installation script - Filelist distribution definition file - wanrouter.rc meta-configuration file - (used by the Setup and wanrouter script) - -/usr/local/wanrouter/doc: - wanpipeForLinux.pdf WAN Router User's Manual - -/usr/local/wanrouter/patches: - wanrouter-v2213.gz patch for Linux kernels 2.2.11 up to 2.2.13. - wanrouter-v2214.gz patch for Linux kernel 2.2.14. - wanrouter-v2215.gz patch for Linux kernels 2.2.15 to 2.2.17. - wanrouter-v2218.gz patch for Linux kernels 2.2.18 and up. - wanrouter-v240.gz patch for Linux kernel 2.4.0. - wanrouter-v242.gz patch for Linux kernel 2.4.2 and up. - wanrouter-v2034.gz patch for Linux kernel 2.0.34 - wanrouter-v2036.gz patch for Linux kernel 2.0.36 and up. - -/usr/local/wanrouter/patches/kdrivers: - Sources of the latest WANPIPE device drivers. - These are used to UPGRADE the linux kernel to the newest - version if the kernel source has already been pathced with - WANPIPE drivers. - -/usr/local/wanrouter/samples: - interface sample interface configuration file - wanpipe1.cpri CHDLC primary port - wanpipe2.csec CHDLC secondary port - wanpipe1.fr Frame Relay protocol - wanpipe1.ppp PPP protocol ) - wanpipe1.asy CHDLC ASYNC protocol - wanpipe1.x25 X25 protocol - wanpipe1.stty Sync TTY driver (Used by Kernel PPPD daemon) - wanpipe1.atty Async TTY driver (Used by Kernel PPPD daemon) - wanrouter.rc sample meta-configuration file - -/usr/local/wanrouter/util: - * wan-tools utilities source code - -/usr/local/wanrouter/api/x25: - * x25 api sample programs. -/usr/local/wanrouter/api/chdlc: - * chdlc api sample programs. -/usr/local/wanrouter/api/fr: - * fr api sample programs. -/usr/local/wanrouter/config/wancfg: - wancfg WANPIPE GUI configuration program. - Creates wanpipe#.conf files. -/usr/local/wanrouter/config/cfgft1: - cfgft1 GUI CSU/DSU configuration program. - -/usr/include/linux: - wanrouter.h router API definitions - wanpipe.h WANPIPE API definitions - sdladrv.h SDLA support module API definitions - sdlasfm.h SDLA firmware module definitions - if_wanpipe.h WANPIPE Socket definitions - if_wanpipe_common.h WANPIPE Socket/Driver common definitions. - sdlapci.h WANPIPE PCI definitions - - -/usr/src/linux/net/wanrouter: - * wanrouter source code - -/var/log: - wanrouter wanrouter start-up log (created by the Setup script) - -/var/lock: (or /var/lock/subsys for RedHat) - wanrouter wanrouter lock file (created by the Setup script) - -/usr/local/wanrouter/firmware: - fr514.sfm Frame relay firmware for Sangoma S508/S514 card - cdual514.sfm Dual Port Cisco HDLC firmware for Sangoma S508/S514 card - ppp514.sfm PPP Firmware for Sangoma S508 and S514 cards - x25_508.sfm X25 Firmware for Sangoma S508 card. - - -REVISION HISTORY - -1.0.0 December 31, 1996 Initial version - -1.0.1 January 30, 1997 Status and statistics can be read via /proc - filesystem entries. - -1.0.2 April 30, 1997 Added UDP management via monitors. - -1.0.3 June 3, 1997 UDP management for multiple boards using Frame - Relay and PPP - Enabled continuous transmission of Configure - Request Packet for PPP (for 508 only) - Connection Timeout for PPP changed from 900 to 0 - Flow Control Problem fixed for Frame Relay - -1.0.4 July 10, 1997 S508/FT1 monitoring capability in fpipemon and - ppipemon utilities. - Configurable TTL for UDP packets. - Multicast and Broadcast IP source addresses are - silently discarded. - -1.0.5 July 28, 1997 Configurable T391,T392,N391,N392,N393 for Frame - Relay in router.conf. - Configurable Memory Address through router.conf - for Frame Relay, PPP and X.25. (commenting this - out enables auto-detection). - Fixed freeing up received buffers using kfree() - for Frame Relay and X.25. - Protect sdla_peek() by calling save_flags(), - cli() and restore_flags(). - Changed number of Trace elements from 32 to 20 - Added DLCI specific data monitoring in FPIPEMON. -2.0.0 Nov 07, 1997 Implemented protection of RACE conditions by - critical flags for FRAME RELAY and PPP. - DLCI List interrupt mode implemented. - IPX support in FRAME RELAY and PPP. - IPX Server Support (MARS) - More driver specific stats included in FPIPEMON - and PIPEMON. - -2.0.1 Nov 28, 1997 Bug Fixes for version 2.0.0. - Protection of "enable_irq()" while - "disable_irq()" has been enabled from any other - routine (for Frame Relay, PPP and X25). - Added additional Stats for Fpipemon and Ppipemon - Improved Load Sharing for multiple boards - -2.0.2 Dec 09, 1997 Support for PAP and CHAP for ppp has been - implemented. - -2.0.3 Aug 15, 1998 New release supporting Cisco HDLC, CIR for Frame - relay, Dynamic IP assignment for PPP and Inverse - Arp support for Frame-relay. Man Pages are - included for better support and a new utility - for configuring FT1 cards. - -2.0.4 Dec 09, 1998 Dual Port support for Cisco HDLC. - Support for HDLC (LAPB) API. - Supports BiSync Streaming code for S502E - and S503 cards. - Support for Streaming HDLC API. - Provides a BSD socket interface for - creating applications using BiSync - streaming. - -2.0.5 Aug 04, 1999 CHDLC initializatin bug fix. - PPP interrupt driven driver: - Fix to the PPP line hangup problem. - New PPP firmware - Added comments to the startup SYSTEM ERROR messages - Xpipemon debugging application for the X25 protocol - New USER_MANUAL.txt - Fixed the odd boundary 4byte writes to the board. - BiSync Streaming code has been taken out. - Available as a patch. - Streaming HDLC API has been taken out. - Available as a patch. - -2.0.6 Aug 17, 1999 Increased debugging in statup scripts - Fixed insallation bugs from 2.0.5 - Kernel patch works for both 2.2.10 and 2.2.11 kernels. - There is no functional difference between the two packages - -2.0.7 Aug 26, 1999 o Merged X25API code into WANPIPE. - o Fixed a memeory leak for X25API - o Updated the X25API code for 2.2.X kernels. - o Improved NEM handling. - -2.1.0 Oct 25, 1999 o New code for S514 PCI Card - o New CHDLC and Frame Relay drivers - o PPP and X25 are not supported in this release - -2.1.1 Nov 30, 1999 o PPP support for S514 PCI Cards - -2.1.3 Apr 06, 2000 o Socket based x25api - o Socket based chdlc api - o Socket based fr api - o Dual Port Receive only CHDLC support. - o Asynchronous CHDLC support (Secondary Port) - o cfgft1 GUI csu/dsu configurator - o wancfg GUI configuration file - configurator. - o Architectual directory changes. - -beta-2.1.4 Jul 2000 o Dynamic interface configuration: - Network interfaces reflect the state - of protocol layer. If the protocol becomes - disconnected, driver will bring down - the interface. Once the protocol reconnects - the interface will be brought up. - - Note: This option is turned off by default. - - o Dynamic wanrouter setup using 'wanconfig': - wanconfig utility can be used to - shutdown,restart,start or reconfigure - a virtual circuit dynamically. - - Frame Relay: Each DLCI can be: - created,stopped,restarted and reconfigured - dynamically using wanconfig. - - ex: wanconfig card wanpipe1 dev wp1_fr16 up - - o Wanrouter startup via command line arguments: - wanconfig also supports wanrouter startup via command line - arguments. Thus, there is no need to create a wanpipe#.conf - configuration file. - - o Socket based x25api update/bug fixes. - Added support for LCN numbers greater than 255. - Option to pass up modem messages. - Provided a PCI IRQ check, so a single S514 - card is guaranteed to have a non-sharing interrupt. - - o Fixes to the wancfg utility. - o New FT1 debugging support via *pipemon utilities. - o Frame Relay ARP support Enabled. - -beta3-2.1.4 Jul 2000 o X25 M_BIT Problem fix. - o Added the Multi-Port PPP - Updated utilites for the Multi-Port PPP. - -2.1.4 Aut 2000 - o In X25API: - Maximum packet an application can send - to the driver has been extended to 4096 bytes. - - Fixed the x25 startup bug. Enable - communications only after all interfaces - come up. HIGH SVC/PVC is used to calculate - the number of channels. - Enable protocol only after all interfaces - are enabled. - - o Added an extra state to the FT1 config, kernel module. - o Updated the pipemon debuggers. - - o Blocked the Multi-Port PPP from running on kernels - 2.2.16 or greater, due to syncppp kernel module - change. - -beta1-2.1.5 Nov 15 2000 - o Fixed the MulitPort PPP Support for kernels 2.2.16 and above. - 2.2.X kernels only - - o Secured the driver UDP debugging calls - - All illegal netowrk debugging calls are reported to - the log. - - Defined a set of allowed commands, all other denied. - - o Cpipemon - - Added set FT1 commands to the cpipemon. Thus CSU/DSU - configuraiton can be performed using cpipemon. - All systems that cannot run cfgft1 GUI utility should - use cpipemon to configure the on board CSU/DSU. - - - o Keyboard Led Monitor/Debugger - - A new utilty /usr/sbin/wpkbdmon uses keyboard leds - to convey operatinal statistic information of the - Sangoma WANPIPE cards. - NUM_LOCK = Line State (On=connected, Off=disconnected) - CAPS_LOCK = Tx data (On=transmitting, Off=no tx data) - SCROLL_LOCK = Rx data (On=receiving, Off=no rx data - - o Hardware probe on module load and dynamic device allocation - - During WANPIPE module load, all Sangoma cards are probed - and found information is printed in the /var/log/messages. - - If no cards are found, the module load fails. - - Appropriate number of devices are dynamically loaded - based on the number of Sangoma cards found. - - Note: The kernel configuraiton option - CONFIG_WANPIPE_CARDS has been taken out. - - o Fixed the Frame Relay and Chdlc network interfaces so they are - compatible with libpcap libraries. Meaning, tcpdump, snort, - ethereal, and all other packet sniffers and debuggers work on - all WANPIPE netowrk interfaces. - - Set the network interface encoding type to ARPHRD_PPP. - This tell the sniffers that data obtained from the - network interface is in pure IP format. - Fix for 2.2.X kernels only. - - o True interface encoding option for Frame Relay and CHDLC - - The above fix sets the network interface encoding - type to ARPHRD_PPP, however some customers use - the encoding interface type to determine the - protocol running. Therefore, the TURE ENCODING - option will set the interface type back to the - original value. - - NOTE: If this option is used with Frame Relay and CHDLC - libpcap library support will be broken. - i.e. tcpdump will not work. - Fix for 2.2.x Kernels only. - - o Ethernet Bridgind over Frame Relay - - The Frame Relay bridging has been developed by - Kristian Hoffmann and Mark Wells. - - The Linux kernel bridge is used to send ethernet - data over the frame relay links. - For 2.2.X Kernels only. - - o Added extensive 2.0.X support. Most new features of - 2.1.5 for protocols Frame Relay, PPP and CHDLC are - supported under 2.0.X kernels. - -beta1-2.2.0 Dec 30 2000 - o Updated drivers for 2.4.X kernels. - o Updated drivers for SMP support. - o X25API is now able to share PCI interrupts. - o Took out a general polling routine that was used - only by X25API. - o Added appropriate locks to the dynamic reconfiguration - code. - o Fixed a bug in the keyboard debug monitor. - -beta2-2.2.0 Jan 8 2001 - o Patches for 2.4.0 kernel - o Patches for 2.2.18 kernel - o Minor updates to PPP and CHLDC drivers. - Note: No functinal difference. - -beta3-2.2.9 Jan 10 2001 - o I missed the 2.2.18 kernel patches in beta2-2.2.0 - release. They are included in this release. - -Stable Release -2.2.0 Feb 01 2001 - o Bug fix in wancfg GUI configurator. - The edit function didn't work properly. - - -bata1-2.2.1 Feb 09 2001 - o WANPIPE TTY Driver emulation. - Two modes of operation Sync and Async. - Sync: Using the PPPD daemon, kernel SyncPPP layer - and the Wanpipe sync TTY driver: a PPP protocol - connection can be established via Sangoma adapter, over - a T1 leased line. - - The 2.4.0 kernel PPP layer supports MULTILINK - protocol, that can be used to bundle any number of Sangoma - adapters (T1 lines) into one, under a single IP address. - Thus, efficiently obtaining multiple T1 throughput. - - NOTE: The remote side must also implement MULTILINK PPP - protocol. - - Async:Using the PPPD daemon, kernel AsyncPPP layer - and the WANPIPE async TTY driver: a PPP protocol - connection can be established via Sangoma adapter and - a modem, over a telephone line. - - Thus, the WANPIPE async TTY driver simulates a serial - TTY driver that would normally be used to interface the - MODEM to the linux kernel. - - o WANPIPE PPP Backup Utility - This utility will monitor the state of the PPP T1 line. - In case of failure, a dial up connection will be established - via pppd daemon, ether via a serial tty driver (serial port), - or a WANPIPE async TTY driver (in case serial port is unavailable). - - Furthermore, while in dial up mode, the primary PPP T1 link - will be monitored for signs of life. - - If the PPP T1 link comes back to life, the dial up connection - will be shutdown and T1 line re-established. - - - o New Setup installation script. - Option to UPGRADE device drivers if the kernel source has - already been patched with WANPIPE. - - Option to COMPILE WANPIPE modules against the currently - running kernel, thus no need for manual kernel and module - re-compilatin. - - o Updates and Bug Fixes to wancfg utility. - -bata2-2.2.1 Feb 20 2001 - - o Bug fixes to the CHDLC device drivers. - The driver had compilation problems under kernels - 2.2.14 or lower. - - o Bug fixes to the Setup installation script. - The device drivers compilation options didn't work - properly. - - o Update to the wpbackupd daemon. - Optimized the cross-over times, between the primary - link and the backup dialup. - -beta3-2.2.1 Mar 02 2001 - o Patches for 2.4.2 kernel. - - o Bug fixes to util/ make files. - o Bug fixes to the Setup installation script. - - o Took out the backupd support and made it into - as separate package. - -beta4-2.2.1 Mar 12 2001 - - o Fix to the Frame Relay Device driver. - IPSAC sends a packet of zero length - header to the frame relay driver. The - driver tries to push its own 2 byte header - into the packet, which causes the driver to - crash. - - o Fix the WANPIPE re-configuration code. - Bug was found by trying to run the cfgft1 while the - interface was already running. - - o Updates to cfgft1. - Writes a wanpipe#.cfgft1 configuration file - once the CSU/DSU is configured. This file can - holds the current CSU/DSU configuration. - - - ->>>>>> END OF README <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< - - -- cgit v1.2.2 From 9fd5559c1f916f284b5b0866148e076866de6f99 Mon Sep 17 00:00:00 2001 From: Alexey Dobriyan Date: Sat, 25 Jun 2005 14:59:34 -0700 Subject: [PATCH] DCO: use IANA-reserved second level domain name Signed-off-by: Alexey Dobriyan Signed-off-by: Domen Puncer Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/SubmittingPatches | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'Documentation') diff --git a/Documentation/SubmittingPatches b/Documentation/SubmittingPatches index 4d35562b1cf9..bcdeee146ff1 100644 --- a/Documentation/SubmittingPatches +++ b/Documentation/SubmittingPatches @@ -299,7 +299,7 @@ can certify the below: then you just add a line saying - Signed-off-by: Random J Developer + Signed-off-by: Random J Developer Some people also put extra tags at the end. They'll just be ignored for now, but you can do this to mark internal company procedures or just -- cgit v1.2.2 From 98e7f29418a4931f97e6b78d1ef3a47103fe6cd5 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Sat, 25 Jun 2005 14:59:37 -0700 Subject: [PATCH] schedule the obsolete raw driver for removal Since kernel 2.6.3 the Kconfig text explicitely stated this driver was obsolete. (trolling for IBMers) Signed-off-by: Adrian Bunk Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/feature-removal-schedule.txt | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'Documentation') diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 77511af45362..1d227ee3792a 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -43,6 +43,14 @@ Who: Randy Dunlap --------------------------- +What: RAW driver (CONFIG_RAW_DRIVER) +When: December 2005 +Why: declared obsolete since kernel 2.6.3 + O_DIRECT can be used instead +Who: Adrian Bunk + +--------------------------- + What: register_ioctl32_conversion() / unregister_ioctl32_conversion() When: April 2005 Why: Replaced by ->compat_ioctl in file_operations and other method -- cgit v1.2.2 From 3e1d1d28d99dabe63c64f7f40f1ca1d646de1f73 Mon Sep 17 00:00:00 2001 From: Christoph Lameter Date: Fri, 24 Jun 2005 23:13:50 -0700 Subject: [PATCH] Cleanup patch for process freezing 1. Establish a simple API for process freezing defined in linux/include/sched.h: frozen(process) Check for frozen process freezing(process) Check if a process is being frozen freeze(process) Tell a process to freeze (go to refrigerator) thaw_process(process) Restart process frozen_process(process) Process is frozen now 2. Remove all references to PF_FREEZE and PF_FROZEN from all kernel sources except sched.h 3. Fix numerous locations where try_to_freeze is manually done by a driver 4. Remove the argument that is no longer necessary from two function calls. 5. Some whitespace cleanup 6. Clear potential race in refrigerator (provides an open window of PF_FREEZE cleared before setting PF_FROZEN, recalc_sigpending does not check PF_FROZEN). This patch does not address the problem of freeze_processes() violating the rule that a task may only modify its own flags by setting PF_FREEZE. This is not clean in an SMP environment. freeze(process) is therefore not SMP safe! Signed-off-by: Christoph Lameter Signed-off-by: Linus Torvalds --- Documentation/power/kernel_threads.txt | 3 +-- Documentation/power/swsusp.txt | 3 +-- 2 files changed, 2 insertions(+), 4 deletions(-) (limited to 'Documentation') diff --git a/Documentation/power/kernel_threads.txt b/Documentation/power/kernel_threads.txt index 60b548105edf..fb57784986b1 100644 --- a/Documentation/power/kernel_threads.txt +++ b/Documentation/power/kernel_threads.txt @@ -12,8 +12,7 @@ refrigerator. Code to do this looks like this: do { hub_events(); wait_event_interruptible(khubd_wait, !list_empty(&hub_event_list)); - if (current->flags & PF_FREEZE) - refrigerator(PF_FREEZE); + try_to_freeze(); } while (!signal_pending(current)); from drivers/usb/core/hub.c::hub_thread() diff --git a/Documentation/power/swsusp.txt b/Documentation/power/swsusp.txt index c7c3459fde43..4e1627cc5b51 100644 --- a/Documentation/power/swsusp.txt +++ b/Documentation/power/swsusp.txt @@ -164,8 +164,7 @@ place where the thread is safe to be frozen (no kernel semaphores should be held at that point and it must be safe to sleep there), and add: - if (current->flags & PF_FREEZE) - refrigerator(PF_FREEZE); + try_to_freeze(); If the thread is needed for writing the image to storage, you should instead set the PF_NOFREEZE process flag when creating the thread. -- cgit v1.2.2 From 340ea3972ffc6c9f90b3ac38b70eade1c8efbf5b Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Sun, 26 Jun 2005 03:27:22 -0700 Subject: [PATCH] remove redundant info from SubmittingPatches Since the Trivial Patch Monkey is mentioned both in steps 4. and 5., I removed it from step4 (Select e-mail destination), since it should go under 'Select your CC list'. Signed-off-by: Cosmin Nicolaescu Signed-off-by: Adrian Bunk Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/SubmittingPatches | 15 --------------- 1 file changed, 15 deletions(-) (limited to 'Documentation') diff --git a/Documentation/SubmittingPatches b/Documentation/SubmittingPatches index bcdeee146ff1..4d1f41b84ebc 100644 --- a/Documentation/SubmittingPatches +++ b/Documentation/SubmittingPatches @@ -132,21 +132,6 @@ which require discussion or do not have a clear advantage should usually be sent first to linux-kernel. Only after the patch is discussed should the patch then be submitted to Linus. -For small patches you may want to CC the Trivial Patch Monkey -trivial@rustcorp.com.au set up by Rusty Russell; which collects "trivial" -patches. Trivial patches must qualify for one of the following rules: - Spelling fixes in documentation - Spelling fixes which could break grep(1). - Warning fixes (cluttering with useless warnings is bad) - Compilation fixes (only if they are actually correct) - Runtime fixes (only if they actually fix things) - Removing use of deprecated functions/macros (eg. check_region). - Contact detail and documentation fixes - Non-portable code replaced by portable code (even in arch-specific, - since people copy, as long as it's trivial) - Any fix by the author/maintainer of the file. (ie. patch monkey - in re-transmission mode) - 5) Select your CC (e-mail carbon copy) list. -- cgit v1.2.2