| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
| |
Reorder structure to remove 8 bytes of padding on 64 bit builds.
This shrinks the size to 128 bytes so allowing allocation from a smaller
slab & needed one fewer cache lines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
LKML-Reference: <1269516456.2054.8.camel@localhost>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |\
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into perf/core
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The ftrace_preempt_disable/enable functions were to address a
recursive race caused by the function tracer. The function tracer
traces all functions which makes it easily susceptible to recursion.
One area was preempt_enable(). This would call the scheduler and
the schedulre would call the function tracer and loop.
(So was it thought).
The ftrace_preempt_disable/enable was made to protect against recursion
inside the scheduler by storing the NEED_RESCHED flag. If it was
set before the ftrace_preempt_disable() it would not call schedule
on ftrace_preempt_enable(), thinking that if it was set before then
it would have already scheduled unless it was already in the scheduler.
This worked fine except in the case of SMP, where another task would set
the NEED_RESCHED flag for a task on another CPU, and then kick off an
IPI to trigger it. This could cause the NEED_RESCHED to be saved at
ftrace_preempt_disable() but the IPI to arrive in the the preempt
disabled section. The ftrace_preempt_enable() would not call the scheduler
because the flag was already set before entring the section.
This bug would cause a missed preemption check and cause lower latencies.
Investigating further, I found that the recusion caused by the function
tracer was not due to schedule(), but due to preempt_schedule(). Now
that preempt_schedule is completely annotated with notrace, the recusion
no longer is an issue.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently the trace splice code zeros out the excess bytes in the page before
sending it off to userspace.
This is to make sure userspace is not getting anything it should not be
when reading the pages, because the excess data was never initialized
to zero before writing (for perfomance reasons).
But the splice code has no business in doing this work, it should be
done by the ring buffer. With the latest changes for recording lost
events, the splice code gets it wrong anyway.
Move the zeroing out of excess bytes into the ring buffer code.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The code to store the "lost events" requires knowing the real end
of the page. Since the 'commit' includes the padding at the end of
a page a "real_end" variable was used to keep track of the end not
including the padding.
If events were lost, the reader can place the count of events in
the padded area if there is enough room.
The bug this patch fixes is that when we fill the page we do not
reset the real_end variable, and if the writer had wrapped a few
times, the real_end would be incorrect.
This patch simply resets the real_end if the page was filled.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
| |
Wrap open-coded WARN_ONCE functionality into the equivalent macro.
Signed-off-by: Borislav Petkov <bp@alien8.de>
LKML-Reference: <20100502060354.GA5281@liondog.tnic>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When performing a non-consuming read, a synchronize_sched() is
performed once for every cpu which is actively tracing.
This is very expensive, and can make it take several seconds to open
up the 'trace' file with lots of cpus.
Only one synchronize_sched() call is actually necessary. What is
desired is for all cpus to see the disabling state change. So we
transform the existing sequence:
for_each_cpu() {
ring_buffer_read_start();
}
where each ring_buffer_start() call performs a synchronize_sched(),
into the following:
for_each_cpu() {
ring_buffer_read_prepare();
}
ring_buffer_read_prepare_sync();
for_each_cpu() {
ring_buffer_read_start();
}
wherein only the single ring_buffer_read_prepare_sync() call needs to
do the synchronize_sched().
The first phase, via ring_buffer_read_prepare(), allocates the 'iter'
memory and increments ->record_disabled.
In the second phase, ring_buffer_read_prepare_sync() makes sure this
->record_disabled state is visible fully to all cpus.
And in the final third phase, the ring_buffer_read_start() calls reset
the 'iter' objects allocated in the first phase since we now know that
none of the cpus are adding trace entries any more.
This makes openning the 'trace' file nearly instantaneous on a
sparc64 Niagara2 box with 128 cpus tracing.
Signed-off-by: David S. Miller <davem@davemloft.net>
LKML-Reference: <20100420.154711.11246950.davem@davemloft.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
include/linux/module.h
kernel/module.c
Semantic conflict:
include/trace/events/module.h
Merge reason: Resolve the conflict with upstream commit 5fbfb18 ("Fix up
possibly racy module refcounting")
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | |\ |
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In some error handling cases the lock is not unlocked. The return is
converted to a goto, to share the unlock at the end of the function.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* spin_lock_irq (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
LKML-Reference: <Pine.LNX.4.64.1003291736440.21896@ask.diku.dk>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, binary readers of the ring buffer only know where events were
lost, but not how many events were lost at that location.
This information is available, but it would require adding another
field to the sub buffer header to include it.
But when a event can not fit at the end of a sub buffer, it is written
to the next sub buffer. This means there is a good chance that the
buffer may have room to hold this counter. If it does, write
the counter at the end of the sub buffer and set another flag
in the data size field that states that this information exists.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, when the ring buffer drops events, it does not record
the fact that it did so. It does inform the writer that the event
was dropped by returning a NULL event, but it does not put in any
place holder where the event was dropped.
This is not a trivial thing to add because the ring buffer mostly
runs in overwrite (flight recorder) mode. That is, when the ring
buffer is full, new data will overwrite old data.
In a produce/consumer mode, where new data is simply dropped when
the ring buffer is full, it is trivial to add the placeholder
for dropped events. When there's more room to write new data, then
a special event can be added to notify the reader about the dropped
events.
But in overwrite mode, any new write can overwrite events. A place
holder can not be inserted into the ring buffer since there never
may be room. A reader could also come in at anytime and miss the
placeholder.
Luckily, the way the ring buffer works, the read side can find out
if events were lost or not, and how many events. Everytime a write
takes place, if it overwrites the header page (the next read) it
updates a "overrun" variable that keeps track of the number of
lost events. When a reader swaps out a page from the ring buffer,
it can record this number, perfom the swap, and then check to
see if the number changed, and take the diff if it has, which would be
the number of events dropped. This can be stored by the reader
and returned to callers of the reader.
Since the reader page swap will fail if the writer moved the head
page since the time the reader page set up the swap, this gives room
to record the overruns without worrying about races. If the reader
sets up the pages, records the overrun, than performs the swap,
if the swap succeeds, then the overrun variable has not been
updated since the setup before the swap.
For binary readers of the ring buffer, a flag is set in the header
of each sub page (sub buffer) of the ring buffer. This flag is embedded
in the size field of the data on the sub buffer, in the 31st bit (the size
can be 32 or 64 bits depending on the architecture), but only 27
bits needs to be used for the actual size (less actually).
We could add a new field in the sub buffer header to also record the
number of events dropped since the last read, but this will change the
format of the binary ring buffer a bit too much. Perhaps this change can
be made if the information on the number of events dropped is considered
important enough.
Note, the notification of dropped events is only used by consuming reads
or peeking at the ring buffer. Iterating over the ring buffer does not
keep this information because the necessary data is only available when
a page swap is made, and the iterator does not swap out pages.
Cc: Robert Richter <robert.richter@amd.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "Luis Claudio R. Goncalves" <lclaudio@uudg.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The ring buffer uses 4 byte alignment while recording events into the
buffer, even on 64bit machines. This saves space when there are lots
of events being recorded at 4 byte boundaries.
The ring buffer has a zero copy method to write into the buffer, with
the reserving of space and then committing it. This may cause problems
when writing an 8 byte word into a 4 byte alignment (not 8). For x86 and
PPC this is not an issue, but on some architectures this would cause an
out-of-alignment exception.
This patch uses CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS to determine
if it is OK to use 4 byte alignments on 64 bit machines. If it is not,
it forces the ring buffer event header to be 8 bytes and not 4,
and will align the length of the data to be 8 byte aligned.
This keeps the data payload at 8 byte alignments and will allow these
machines to run without issue.
The trick to this is that the header can be either 4 bytes or 8 bytes
depending on the length of the data payload. The 4 byte header
has a length field that supports up to 112 bytes. If the length of
the data is more than 112, the length field is set to zero, and the actual
length is stored in the next 4 bytes after the header.
When CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set, the code forces
zero in the 4 byte header forcing the length to be stored in the 4 byte
array, even with a small data load. It also forces the length of the
data load to be 8 byte aligned. The combination of these two guarantee
that the data is always at 8 byte alignment.
Tested-by: Frederic Weisbecker <fweisbec@gmail.com>
(on sparc64)
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Do not record user stack trace from NMI context
tracing: Disable buffer switching when starting or stopping trace
tracing: Use same local variable when resetting the ring buffer
function-graph: Init curr_ret_stack with ret_stack
ring-buffer: Move disabled check into preempt disable section
function-graph: Add tracing_thresh support to function_graph tracer
tracing: Update the comm field in the right variable in update_max_tr
function-graph: Use comment notation for func names of dangling '}'
function-graph: Fix unused reference to ftrace_set_func()
tracing: Fix warning in s_next of trace file ops
tracing: Include irqflags headers from trace clock
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The ring buffer resizing and resetting relies on a schedule RCU
action. The buffers are disabled, a synchronize_sched() is called
and then the resize or reset takes place.
But this only works if the disabling of the buffers are within the
preempt disabled section, otherwise a window exists that the buffers
can be written to while a reset or resize takes place.
Cc: stable@kernel.org
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <4B949E43.2010906@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Conflicts:
Documentation/filesystems/proc.txt
arch/arm/mach-u300/include/mach/debug-macro.S
drivers/net/qlge/qlge_ethtool.c
drivers/net/qlge/qlge_main.c
drivers/net/typhoon.c
|
| | |/
| |
| |
| |
| |
| |
| | |
Some comments misspell "truly"; this fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
| |\| |
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If the iterator comes to an empty page for some reason, or if
the page is emptied by a consuming read. The iterator code currently
does not check if the iterator is pass the contents, and may
return a false entry.
This patch adds a check to the ring buffer iterator to test if the
current page has been completely read and sets the iterator to the
next page if necessary.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Usually reads of the ring buffer is performed by a single task.
There are two types of reads from the ring buffer.
One is a consuming read which will consume the entry that was read
and the next read will be the entry that follows.
The other is an iterator that will let the user read the contents of
the ring buffer without modifying it. When an iterator is allocated,
writes to the ring buffer are disabled to protect the iterator.
The problem exists when consuming reads happen while an iterator is
allocated. Specifically, the kind of read that swaps out an entire
page (used by splice) and replaces it with a new read. If the iterator
is on the page that is swapped out, then the next read may read
from this swapped out page and return garbage.
This patch adds a check when reading the iterator to make sure that
the iterator contents are still valid. If a consuming read has taken
place, the iterator is reset.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If the very unlikely case happens where the writer moves the head by one
between where the head page is read and where the new reader page
is assigned _and_ the writer then writes and wraps the entire ring buffer
so that the head page is back to what was originally read as the head page,
the page to be swapped will have a corrupted next pointer.
Simple solution is to wrap the assignment of the next pointer with a
rb_list_head().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This reference at the end of rb_get_reader_page() was causing off-by-one
writes to the prev pointer of the page after the reader page when that
page is the head page, and therefore the reader page has the RB_PAGE_HEAD
flag in its list.next pointer. This eventually results in a GPF in a
subsequent call to rb_set_head_page() (usually from rb_get_reader_page())
when that prev pointer is dereferenced. The dereferenced register would
characteristically have an address that appears shifted left by one byte
(eg, ffxxxxxxxxxxxxyy instead of ffffxxxxxxxxxxxx) due to being written at
an address one byte too high.
Signed-off-by: David Sharp <dhsharp@google.com>
LKML-Reference: <1262826727-9090-1-git-send-email-dhsharp@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |/
|
|
|
|
|
|
|
| |
ringbuffer*.c are the last users of local.h.
Remove the include from modules.h and add it to ringbuffer files.
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix return of trace_dump_stack()
ksym_tracer: Fix bad cast
tracing/power: Remove two exports
tracing: Change event->profile_count to be int type
tracing: Simplify trace_option_write()
tracing: Remove useless trace option
tracing: Use seq file for trace_clock
tracing: Use seq file for trace_options
function-graph: Allow writing the same val to set_graph_function
ftrace: Call trace_parser_clear() properly
ftrace: Return EINVAL when writing invalid val to set_ftrace_filter
tracing: Move a printk out of ftrace_raw_reg_event_foo()
tracing: Pull up calls to trace_define_common_fields()
tracing: Extract duplicate ftrace_raw_init_event_foo()
ftrace.h: Use common pr_info fmt string
tracing: Add stack trace to irqsoff tracer
tracing: Add trace_dump_stack()
ring-buffer: Move resize integrity check under reader lock
ring-buffer: Use sync sched protection on ring buffer resizing
tracing: Fix wrong usage of strstrip in trace_ksyms
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
While using an application that does splice on the ftrace ring
buffer at start up, I triggered an integrity check failure.
Looking into this, I discovered that resizing the buffer performs
an integrity check after the buffer is resized. This check unfortunately
is preformed after it releases the reader lock. If a reader is
reading the buffer it may cause the integrity check to trigger a
false failure.
This patch simply moves the integrity checker under the protection
of the ring buffer reader lock.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There was a comment in the ring buffer code that says the calling
layers should prevent tracing or reading of the ring buffer while
resizing. I have discovered that the tracers do not honor this
arrangement.
This patch moves the disabling and synchronizing the ring buffer to
a higher layer during resizing. This guarantees that no writes
are occurring while the resize takes place.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Name space cleanup. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Further name space cleanup. No functional change
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The raw_spin* namespace was taken by lockdep for the architecture
specific implementations. raw_spin_* would be the ideal name space for
the spinlocks which are not converted to sleeping locks in preempt-rt.
Linus suggested to convert the raw_ to arch_ locks and cleanup the
name space instead of using an artifical name like core_spin,
atomic_spin or whatever
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (470 commits)
x86: Fix comments of register/stack access functions
perf tools: Replace %m with %a in sscanf
hw-breakpoints: Keep track of user disabled breakpoints
tracing/syscalls: Make syscall events print callbacks static
tracing: Add DEFINE_EVENT(), DEFINE_SINGLE_EVENT() support to docbook
perf: Don't free perf_mmap_data until work has been done
perf_event: Fix compile error
perf tools: Fix _GNU_SOURCE macro related strndup() build error
trace_syscalls: Remove unused syscall_name_to_nr()
trace_syscalls: Simplify syscall profile
trace_syscalls: Remove duplicate init_enter_##sname()
trace_syscalls: Add syscall_nr field to struct syscall_metadata
trace_syscalls: Remove enter_id exit_id
trace_syscalls: Set event_enter_##sname->data to its metadata
trace_syscalls: Remove unused event_syscall_enter and event_syscall_exit
perf_event: Initialize data.period in perf_swevent_hrtimer()
perf probe: Simplify event naming
perf probe: Add --list option for listing current probe events
perf probe: Add argv_split() from lib/argv_split.c
perf probe: Move probe event utility functions to probe-event.c
...
|
| | |\
| | |
| | |
| | |
| | |
| | | |
Merge reason: pick up perf fixlets
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Conflicts:
tools/perf/Makefile
Merge reason: Resolve the conflict, merge to upstream and merge in
perf fixes so we can add a dependent patch.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The sign info used for filters in the kernel is also useful to
applications that process the trace stream. Add it to the format
files and make it available to userspace.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: rostedt@goodmis.org
Cc: lizf@cn.fujitsu.com
Cc: hch@infradead.org
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1254809398-8078-2-git-send-email-tzanussi@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |\ \ \ \
| |_|_|/
|/| | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits)
tracing: Separate raw syscall from syscall tracer
ring-buffer-benchmark: Add parameters to set produce/consumer priorities
tracing, function tracer: Clean up strstrip() usage
ring-buffer benchmark: Run producer/consumer threads at nice +19
tracing: Remove the stale include/trace/power.h
tracing: Only print objcopy version warning once from recordmcount
tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used
ring-buffer: Move access to commit_page up into function used
tracing: do not disable interrupts for trace_clock_local
ring-buffer: Add multiple iterations between benchmark timestamps
kprobes: Sanitize struct kretprobe_instance allocations
tracing: Fix to use __always_unused attribute
compiler: Introduce __always_unused
tracing: Exit with error if a weak function is used in recordmcount.pl
tracing: Move conditional into update_funcs() in recordmcount.pl
tracing: Add regex for weak functions in recordmcount.pl
tracing: Move mcount section search to front of loop in recordmcount.pl
tracing: Fix objcopy revision check in recordmcount.pl
tracing: Check absolute path of input file in recordmcount.pl
tracing: Correct the check for number of arguments in recordmcount.pl
...
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With the change of the way we process commits. Where a commit only happens
at the outer most level, and that we don't need to worry about
a commit ending after the rb_start_commit() has been called, the code
use to grab the commit page before the tail page to prevent a possible
race. But this race no longer exists with the rb_start_commit()
rb_end_commit() interface.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We got a sudden panic when we reduced the size of the
ringbuffer.
We can reproduce the panic by the following steps:
echo 1 > events/sched/enable
cat trace_pipe > /dev/null &
while ((1))
do
echo 12000 > buffer_size_kb
echo 512 > buffer_size_kb
done
(not more than 5 seconds, panic ...)
Reported-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <4AF01735.9060409@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The cpu argument is not used inside the rb_time_stamp() function.
Plus fix a typo.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20091023233647.118547500@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |/
|
|
|
|
|
|
|
|
|
| |
Trivial patch to fix a documentation example and to fix a
comment.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20091023233646.871719877@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
fix the following 'make includecheck' warning:
kernel/trace/ring_buffer.c: trace.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247068617.4382.107.camel@ht.satnam>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The cmpxchg used by PowerPC does the following:
({ \
__typeof__(*(ptr)) _o_ = (o); \
__typeof__(*(ptr)) _n_ = (n); \
(__typeof__(*(ptr))) __cmpxchg((ptr), (unsigned long)_o_, \
(unsigned long)_n_, sizeof(*(ptr))); \
})
This does a type check of *ptr to both o and n.
Unfortunately, the code in ring-buffer.c assigns longs to pointers
and pointers to longs and causes a warning on PowerPC:
ring_buffer.c: In function 'rb_head_page_set':
ring_buffer.c:704: warning: initialization makes pointer from integer without a cast
ring_buffer.c:704: warning: initialization makes pointer from integer without a cast
ring_buffer.c: In function 'rb_head_page_replace':
ring_buffer.c:797: warning: initialization makes integer from pointer without a cast
This patch adds the typecasts inside cmpxchg to annotate that a long is
being cast to a pointer and a pointer is being casted to a long and this
removes the PowerPC warnings.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
rb_buffer_peek() operates with struct ring_buffer_per_cpu *cpu_buffer
only. Thus, instead of passing variables buffer and cpu it is better
to use cpu_buffer directly. This also reduces the risk of races since
cpu_buffer is not calculated twice.
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <1249045084-3028-1-git-send-email-robert.richter@amd.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Since the ability to swap the cpu buffers adds a small overhead to
the recording of a trace, we only want to add it when needed.
Only the irqsoff and preemptoff tracers use this feature, and both are
not recommended for production kernels. This patch disables its use
when neither irqsoff nor preemptoff is configured.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
|
| |
Because the irqsoff tracer can swap an internal CPU buffer, it is possible
that a swap happens between the start of the write and before the committing
bit is set (the committing bit will disable swapping).
This patch adds a check for this and will fail the write if it detects it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently the way RB_WARN_ON works, is to disable either the current
CPU buffer or all CPU buffers, depending on whether a ring_buffer or
ring_buffer_per_cpu struct was passed into the macro.
Most users of the RB_WARN_ON pass in the CPU buffer, so only the one
CPU buffer gets disabled but the rest are still active. This may
confuse users even though a warning is sent to the console.
This patch changes the macro to disable the entire buffer even if
the CPU buffer is passed in.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The latency tracers report the number of items in the trace buffer.
This uses the ring buffer data to calculate this. Because discarded
events are also counted, the numbers do not match the number of items
that are printed. The ring buffer also adds a "padding" item to the
end of each buffer page which also gets counted as a discarded item.
This patch decrements the counter to the page entries on a discard.
This allows us to ignore discarded entries while reading the buffer.
Decrementing the counter is still safe since it can only happen while
the committing flag is still set.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The function ring_buffer_event_discard can be used on any item in the
ring buffer, even after the item was committed. This function provides
no safety nets and is very race prone.
An item may be safely removed from the ring buffer before it is committed
with the ring_buffer_discard_commit.
Since there are currently no users of this function, and because this
function is racey and error prone, this patch removes it altogether.
Note, removing this function also allows the counters to ignore
all discarded events (patches will follow).
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When the ring buffer uses an iterator (static read mode, not on the
fly reading), when it crosses a page boundery, it will skip the first
entry on the next page. The reason is that the last entry of a page
is usually padding if the page is not full. The padding will not be
returned to the user.
The problem arises on ring_buffer_read because it also increments the
iterator. Because both the read and peek use the same rb_iter_peek,
the rb_iter_peak will return the padding but also increment to the next
item. This is because the ring_buffer_peek will not incerment it
itself.
The ring_buffer_read will increment it again and then call rb_iter_peek
again to get the next item. But that will be the second item, not the
first one on the page.
The reason this never showed up before, is because the ftrace utility
always calls ring_buffer_peek first and only uses ring_buffer_read
to increment to the next item. The ring_buffer_peek will always keep
the pointer to a valid item and not padding. This just hid the bug.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
|
|
| |
The loops in the ring buffer that use cpu_relax are not dependent on
other CPUs. They simply came across some padding in the ring buffer and
are skipping over them. It is a normal loop and does not require a
cpu_relax.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |
|
|
|
|
|
| |
If a commit is taking place on a CPU ring buffer, do not allow it to
be swapped. Return -EBUSY when this is detected instead.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
