| Commit message (Collapse) | Author | Age |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This ugly hack add support for Siemens MC45 PCMCIA GPRS card (which is
identical to Possio GCC, and which is offered by one of our local GPRS
providers). Card has unfortunate feature that after poweron oxcf950 chip
is fully powered and works, but attached MC45 modem is powered down :-(
There is a special sequence (which takes 1 sec :-( ) to poweron MC45 (and
after MC45 powers on, it takes more than 2 secs until firmware fully
boots...) which needs to be executed after all powerons.
I'm really not familiar with PCMCIA subsystem, so I have no idea whether I
should issue request_region() on rest of oxcf950 address range (0-7 is
UART, 8-F are special configuration registers), or how this should be
better integrated with PM system and so on - I just put it in same place
where another hack already lived...
Card uses 18.432MHz XTAL, so to get it to work you must add lines below to
the /etc/pcmcia/serial.opts.
case "$MANFID-$FUNCID-$PRODID_1-$PRODID_2-$PRODID_3-$PRODID_4" in
'030c,0003-2-GPRS-CARD--')
SERIAL_OPTS="baud_base 1152000"
;;
esac
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
| |
Instead of the DEV_OK macro, drivers should use pcmcia_dev_present().
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
|
| |
Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
| |
Remove the unused DEV_RELEASE_PENDING flag, and move the DEV_SUSPEND flag
into the p_dev structure, and make use of it at the core level.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
| |
dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
| |
Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
| |
Rename pcmcia_device.state (which is used in very few places) to p_state
in order to avoid a namespace collision when moving the deprecated
dev_link_t into struct pcmcia_device
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
| |
As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
|
| |
Handle the _modifying_ operation sm91c92_cs requires in
pcmcia_modify_configuration, so that the only remaining users
of pcmcia_release_configuration() are within the pcmcia core
module.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
|
| |
In all but one case, the suspend and resume functions of PCMCIA drivers
contain mostly of calls to pcmcia_release_configuration() and
pcmcia_request_configuration(). Therefore, move this code out of the
drivers and into the core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
| |
Convert the remaining drivers which use pcmcia_release_io or
pcmcia_release_irq, and remove the EXPORT of these symbols.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
|
| |
pcmcia_disable_device(struct pcmcia_device *p_dev) performs the necessary
cleanups upon device or driver removal: it calls the appropriate
pcmcia_release_* functions, and can replace (most) of the current drivers'
_release() functions.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the Compact Flash controller integrated in
the Atmel AT91RM9200 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
| |
Remove misleading comment.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
| |
BasePort, NumPorts and Attributes are or can be embedded in
struct resource, so remove them.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
| |
If the kernel is configured to not include the deprecated PCMCIA ioctl,
some code doesn't need to be built.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
| |
Remove the compatibility wrappers, as they can (now) also be implemented
using macros. Please continue using these wrappers instead of new functions
until a new API has stabilized.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
| |
Use mutexes in the PCMICA core, as they suffice for what needs to be done.
Includes a bugfix from and Signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
| |
Remove unused fields and declarations.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
| |
Handle config_t structs independent of struct pcmcia_socket, and add
reference counting for them.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
|
|
|
|
|
|
|
| |
Access the PCMCIA config_t struct (one per device function) using
a pointer in struct pcmcia_device, instead of looking them up in
an array.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6: (24 commits)
[PARISC] Fix double free when removing HIL drivers
[PARISC] Add atomic_sub_and_test
[PARISC] Enabled some NLS modules in a500, b180 and c3000 defconfigs
[PARISC] Kill duplicated EXPORT_SYMBOL warnings
[PARISC] Move ioremap EXPORT_SYMBOL from parisc_ksyms.c
[PARISC] Make local_t use atomic_long_t
[PARISC] Update defconfigs
[PARISC] Add PREEMPT support
[PARISC] More useful readwrite lock helpers
[PARISC] Convert HIL drivers to use input_allocate_device
[PARISC] Fixup CONFIG_EISA a bit
[PARISC] getsockopt should be ENTRY_COMP
[PARISC] Remove obsolete CONFIG_DEBUG_IOREMAP
[PARISC] Temporary FIXME for ioremapping EISA regions
[PARISC] Enable ioremap functionality unconditionally
[PARISC] Fix stifb with IOREMAP and a 64-bit kernel
[PARISC] Add CONFIG_HPPA_IOREMAP to conditionally enable ioremap
[PARISC] Add STRICT_MM_TYPECHECKS
[PARISC] Fix IOREMAP with a 64-bit kernel
[PARISC] Add parisc implementation of flush_kernel_dcache_page()
...
|
| |
| |
| |
| |
| |
| | |
Define atomic_sub_and_test to fix build failures.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| | |
As done in asm-generic/local.h in mainline. Otherwise local_t was 32-bit
even on a 64-bit kernel.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| | |
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| | |
spinlock.c needs _can_lock helpers. Rewrite _is_locked helpers to be
_can_lock helpers.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix up some ISA/EISA stuff.
(Note: isa_ accessors have been removed from asm/io.h)
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Remove CONFIG_DEBUG_IOREMAP, it's now obsolete and won't work anyway.
Remove it from lib/KConfig since it was only available on parisc.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| | |
Enable CONFIG_HPPA_IOREMAP by default and remove all now unnecessary code.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Instead of making it a #define in asm/io.h, allow user to select
to turn on IOREMAP from the config menu.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| | |
Add STRICT_MM_TYPECHECKS to page.h as other architectures do.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| |
| | |
We need to do a little renaming of our original syntax because
of the difference in arguments.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| |
| | |
This should now allow SG_IO and fuse to function correctly on our
platform.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
| |
| |
| |
| |
| |
| |
| | |
pdc_stable.c is explicitly licensed under GPL version 2.
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mad: RMPP support for additional classes
IB/mad: include GID/class when matching receives
IB/mthca: Fix section mismatch problems
IPoIB: Fix oops with raw sockets
IB/mthca: Fix check of size in SRQ creation
IB/srp: Fix unmapping of fake scatterlist
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add RMPP support for additional management classes that support it.
Also, validate RMPP is consistent with management class specified.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] sata_mv: three bug fixes
[PATCH] libata: ata_dev_init_params() fixes
[PATCH] libata: Fix interesting use of "extern" and also some bracketing
[PATCH] libata: Simplex and other mode filtering logic
[PATCH] libata - ATA is both ATA and CFA
[PATCH] libata: Add ->set_mode hook for odd drivers
[PATCH] libata: BMDMA handling updates
[PATCH] libata: kill trailing whitespace
[PATCH] libata: add FIXME above ata_dev_xfermask()
[PATCH] libata: cosmetic changes in ata_bus_softreset()
[PATCH] libata: kill E.D.D.
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add a field to the host_set called 'flags' (was host_set_flags changed
to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel
Add a ->mode_filter() hook to allow drivers to filter modes
Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core
This provides the needed framework to support all the mode rules found
in the PATA world. The simplex filter deals with 'to spec' simplex DMA
systems found in older chips. The cable filter avoids duplicating the
same rules in each chip driver with PATA. Finally the mode filter is
neccessary because drive/chip combinations have errata that forbid
certain modes with some drives or types of ATA object.
Drive speed setup remains per channel for now and the filters now use
the framework Tejun put into place which cleans them up a lot from the
older libata-pata patches.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Some hardware doesn't want the usual mode setup logic running. This
allows the hardware driver to replace it for special cases in the least
invasive way possible.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This is the minimal patch set to enable the current code to be used with
a controller following SFF (ie any PATA and early SATA controllers)
safely without crashes if there is no BMDMA area or if BMDMA is not
assigned by the BIOS for some reason.
Simplex status is recorded but not acted upon in this change, this isn't
a problem with the current drivers as none of them are for simplex
hardware. A following diff will deal with that.
The flags in the probe structure remain ->host_set_flags although Jeff
asked me to rename them, simply because the rename would break the usual
Linux rules that old code should break when there are changes. not
compile and run and then blow up/eat your computer/etc. Renaming this
later is a trivial exercise once a better name is chosen.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
| |\ \ \
| | | |/
| | |/| |
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
E.D.D. has no user in-tree and mostly useless. Kill it. For possible
out-of-tree users, add a nice warning message and error handling if
LLDD doesn't report any useable reset mechanism (and thus tries to use
E.D.D.).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] ioremap() should prefer WB over UC
[IA64] Add __mca_table to the DISCARD list in gate.lds
[IA64] Move __mca_table out of the __init section
[IA64] simplify some condition checks in iosapic_check_gsi_range
[IA64] correct some messages and fixes some minor things
[IA64-SGI] fix for-loop in sn_hwperf_geoid_to_cnode()
[IA64-SGI] sn_hwperf use of num_online_cpus()
[IA64] optimize flush_tlb_range on large numa box
[IA64] lazy_mmu_prot_update needs to be aware of huge pages
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add __mca_table to the DISCARD list for the gate.lds linker script to
avoid broken linker references when linking the final vmlinux file.
Also add comment to include/asm-ia64/asmmacros.h to avoid anyone else
hitting this problem in the future.
Credits to James Bottomley <James.Bottomley@SteelEye.com> for spotting
the DISCARD list in gate.lds.S
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This enables the caller to migrate pages from one address space page
cache to another. In buzz word marketing, you can do zero-copy file
copies!
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |_|/ /
|/| | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This adds support for the sys_splice system call. Using a pipe as a
transport, it can connect to files or sockets (latter as output only).
From the splice.c comments:
"splice": joining two ropes together by interweaving their strands.
This is the "extended pipe" functionality, where a pipe is used as
an arbitrary in-memory buffer. Think of a pipe as a small kernel
buffer that you can use to transfer data from one end to the other.
The traditional unix read/write is extended with a "splice()" operation
that transfers data buffers to or from a pipe buffer.
Named by Larry McVoy, original implementation from Linus, extended by
Jens to support splicing to files and fixing the initial implementation
bugs.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: Rename init functions.
[TCP]: Fix RFC2465 typo.
[INET]: Introduce tunnel4/tunnel6
[NET]: deinline 200+ byte inlines in sock.h
[ECONET]: Convert away from SOCKOPS_WRAPPED
[NET]: Fix ipx/econet/appletalk/irda ioctl crashes
[NET]: Kill Documentation/networking/TODO
[TG3]: Update version and reldate
[TG3]: Skip timer code during full lock
[TG3]: Speed up SRAM access
[TG3]: Fix PHY loopback on 5700
[TG3]: Fix bug in 40-bit DMA workaround code
[TG3]: Fix probe failure due to invalid MAC address
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Basically this patch moves the generic tunnel protocol stuff out of
xfrm4_tunnel/xfrm6_tunnel and moves it into the new files of tunnel4.c
and tunnel6 respectively.
The reason for this is that the problem that Hugo uncovered is only
the tip of the iceberg. The real problem is that when we removed the
dependency of ipip on xfrm4_tunnel we didn't really consider the module
case at all.
For instance, as it is it's possible to build both ipip and xfrm4_tunnel
as modules and if the latter is loaded then ipip simply won't load.
After considering the alternatives I've decided that the best way out of
this is to restore the dependency of ipip on the non-xfrm-specific part
of xfrm4_tunnel. This is acceptable IMHO because the intention of the
removal was really to be able to use ipip without the xfrm subsystem.
This is still preserved by this patch.
So now both ipip/xfrm4_tunnel depend on the new tunnel4.c which handles
the arbitration between the two. The order of processing is determined
by a simple integer which ensures that ipip gets processed before
xfrm4_tunnel.
The situation for ICMP handling is a little bit more complicated since
we may not have enough information to determine who it's for. It's not
a big deal at the moment since the xfrm ICMP handlers are basically
no-ops. In future we can deal with this when we look at ICMP caching
in general.
The user-visible change to this is the removal of the TUNNEL Kconfig
prompts. This makes sense because it can only be used through IPCOMP
as it stands.
The addition of the new modules shouldn't introduce any problems since
module dependency will cause them to be loaded.
Oh and I also turned some unnecessary pskb's in IPv6 related to this
patch to skb's.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Sizes in bytes (allyesconfig, i386) and files where those inlines
are used:
238 sock_queue_rcv_skb 2.6.16/net/x25/x25_in.o
238 sock_queue_rcv_skb 2.6.16/net/rose/rose_in.o
238 sock_queue_rcv_skb 2.6.16/net/packet/af_packet.o
238 sock_queue_rcv_skb 2.6.16/net/netrom/nr_in.o
238 sock_queue_rcv_skb 2.6.16/net/llc/llc_sap.o
238 sock_queue_rcv_skb 2.6.16/net/llc/llc_conn.o
238 sock_queue_rcv_skb 2.6.16/net/irda/af_irda.o
238 sock_queue_rcv_skb 2.6.16/net/ipx/af_ipx.o
238 sock_queue_rcv_skb 2.6.16/net/ipv6/udp.o
238 sock_queue_rcv_skb 2.6.16/net/ipv6/raw.o
238 sock_queue_rcv_skb 2.6.16/net/ipv4/udp.o
238 sock_queue_rcv_skb 2.6.16/net/ipv4/raw.o
238 sock_queue_rcv_skb 2.6.16/net/ipv4/ipmr.o
238 sock_queue_rcv_skb 2.6.16/net/econet/econet.o
238 sock_queue_rcv_skb 2.6.16/net/econet/af_econet.o
238 sock_queue_rcv_skb 2.6.16/net/bluetooth/sco.o
238 sock_queue_rcv_skb 2.6.16/net/bluetooth/l2cap.o
238 sock_queue_rcv_skb 2.6.16/net/bluetooth/hci_sock.o
238 sock_queue_rcv_skb 2.6.16/net/ax25/ax25_in.o
238 sock_queue_rcv_skb 2.6.16/net/ax25/af_ax25.o
238 sock_queue_rcv_skb 2.6.16/net/appletalk/ddp.o
238 sock_queue_rcv_skb 2.6.16/drivers/net/pppoe.o
276 sk_receive_skb 2.6.16/net/decnet/dn_nsp_in.o
276 sk_receive_skb 2.6.16/net/dccp/ipv6.o
276 sk_receive_skb 2.6.16/net/dccp/ipv4.o
276 sk_receive_skb 2.6.16/net/dccp/dccp_ipv6.o
276 sk_receive_skb 2.6.16/drivers/net/pppoe.o
209 sk_dst_check 2.6.16/net/ipv6/ip6_output.o
209 sk_dst_check 2.6.16/net/ipv4/udp.o
209 sk_dst_check 2.6.16/net/decnet/dn_nsp_out.o
Large inlines with multiple callers:
Size Uses Wasted Name and definition
===== ==== ====== ================================================
238 21 4360 sock_queue_rcv_skb include/net/sock.h
109 10 801 sock_recv_timestamp include/net/sock.h
276 4 768 sk_receive_skb include/net/sock.h
94 8 518 __sk_dst_check include/net/sock.h
209 3 378 sk_dst_check include/net/sock.h
131 4 333 sk_setup_caps include/net/sock.h
152 2 132 sk_stream_alloc_pskb include/net/sock.h
125 2 105 sk_stream_writequeue_purge include/net/sock.h
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \ \ \ \
| |_|_|_|/
|/| | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (67 commits)
[PATCH] powerpc: Remove oprofile spinlock backtrace code
[PATCH] powerpc: Add oprofile calltrace support to all powerpc cpus
[PATCH] powerpc: Add oprofile calltrace support
[PATCH] for_each_possible_cpu: ppc
[PATCH] for_each_possible_cpu: powerpc
[PATCH] lock PTE before updating it in 440/BookE page fault handler
[PATCH] powerpc: Kill _machine and hard-coded platform numbers
ppc: Fix compile error in arch/ppc/lib/strcase.c
[PATCH] git-powerpc: WARN was a dumb idea
[PATCH] powerpc: a couple of trivial compile warning fixes
powerpc: remove OCP references
powerpc: Make uImage default build output for MPC8540 ADS
powerpc: move math-emu over to arch/powerpc
powerpc: use memparse() for mem= command line parsing
ppc: fix strncasecmp prototype
[PATCH] powerpc: make ISA floppies work again
[PATCH] powerpc: Fix some initcall return values
[PATCH] powerpc: Workaround for pSeries RTAS bug
[PATCH] spufs: fix __init/__exit annotations
[PATCH] powerpc: add hvc backend for rtas
...
|