aboutsummaryrefslogtreecommitdiffstats
path: root/include
Commit message (Collapse)AuthorAge
* rapidio: fix IDLE2 bits corruptionAlexandre Bounine2010-10-27
| | | | | | | | | | | | | | | RapidIO spec v.2.1 adds Idle Sequence 2 into LP-Serial Physical Layer. The fix ensures that corresponding bits are not corrupted during error handling. Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Micha Nelissen <micha@neli.hopto.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rapidio: add handling of redundant routesAlexandre Bounine2010-10-27
| | | | | | | | | | | | | | | | | | | | | | Detects RIO link to the already enumerated device and properly sets links between device objects. Changes to the enumeration/discovery logic: 1. Use Master Enable bit to signal end of the enumeration - agents may start their discovery process as soon as they see this bit set (Component Tag register was used before for this purpose). 2. Enumerator sets Component Tag (!= 0) immediately during device setup. This allows to identify the device if the redundant route exists in a RIO system. Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Micha Nelissen <micha@neli.hopto.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rapidio: add support for IDT CPS Gen2 switchesAlexandre Bounine2010-10-27
| | | | | | | | | | | | | | Add the RIO switch driver and definitions for IDT CPS-1848 and CPS-1616 Gen2 devices. Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Micha Nelissen <micha@neli.hopto.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rapidio: modify sysfs initialization for switchesAlexandre Bounine2010-10-27
| | | | | | | | | | | | | | | 1. Change to create attribute "routes" only for switches. 2. Add a switch-specific callback to create/remove proprietary attributes. Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Micha Nelissen <micha@neli.hopto.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rapidio: add default handler for error-stopped stateAlexandre Bounine2010-10-27
| | | | | | | | | | | | | | The default error-stopped state handler provides recovery mechanism as defined by RIO specification. Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Micha Nelissen <micha@neli.hopto.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rapidio: add relation links between RIO device structuresAlexandre Bounine2010-10-27
| | | | | | | | | | | | | | | | Create back and forward links between RIO devices. These links are intended for use by error management and hot-plug extensions. Links for redundant RIO connections between switches are not set (will be fixed in a separate patch). Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Micha Nelissen <micha@neli.hopto.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rapidio: use stored ingress port number instead of register readAlexandre Bounine2010-10-27
| | | | | | | | | | | | | | | The switch port information is obtained and stored during RIO device setup. Therefore repeated reads from Switch Port Information CAR may be removed. Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Micha Nelissen <micha@neli.hopto.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rapidio: fix RapidIO sysfs hierarchyAlexandre Bounine2010-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | This set of RapidIO patches extends support for standard error recovery mechanism and adds new IDT Gen2 sRIO switch devices - CPS-1848 and CPS-1616. Implementation of the standard error-stopped state recovery mechanism (as defined by the RapidIO specification) is required for the new switches. Version 2 of this set of patches addresses received comments and fixes an error notification setup issue found in the idt_gen2.c after the first version was released. This patch: Make RapidIO devices appear in /sys/devices/rapidio directory instead of top of /sys/devices directory. Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Micha Nelissen <micha@neli.hopto.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* drivers/char/synclink_gt.c: add extended sync featurePaul Fulghum2010-10-27
| | | | | | | | Add support for extended byte synchronous mode feature of hardware. Signed-off-by: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* /proc/stat: fix scalability of irq sum of all cpuKAMEZAWA Hiroyuki2010-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In /proc/stat, the number of per-IRQ event is shown by making a sum each irq's events on all cpus. But we can make use of kstat_irqs(). kstat_irqs() do the same calculation, If !CONFIG_GENERIC_HARDIRQ, it's not a big cost. (Both of the number of cpus and irqs are small.) If a system is very big and CONFIG_GENERIC_HARDIRQ, it does for_each_irq() for_each_cpu() - look up a radix tree - read desc->irq_stat[cpu] This seems not efficient. This patch adds kstat_irqs() for CONFIG_GENRIC_HARDIRQ and change the calculation as for_each_irq() look up radix tree for_each_cpu() - read desc->irq_stat[cpu] This reduces cost. A test on (4096cpusp, 256 nodes, 4592 irqs) host (by Jack Steiner) %time cat /proc/stat > /dev/null Before Patch: 2.459 sec After Patch : .561 sec [akpm@linux-foundation.org: unexport kstat_irqs, coding-style tweaks] [akpm@linux-foundation.org: fix unused variable 'per_irq_sum'] Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Tested-by: Jack Steiner <steiner@sgi.com> Acked-by: Jack Steiner <steiner@sgi.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* /proc/stat: scalability of irq num per cpuKAMEZAWA Hiroyuki2010-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | /proc/stat shows the total number of all interrupts to each cpu. But when the number of IRQs are very large, it take very long time and 'cat /proc/stat' takes more than 10 secs. This is because sum of all irq events are counted when /proc/stat is read. This patch adds "sum of all irq" counter percpu and reduce read costs. The cost of reading /proc/stat is important because it's used by major applications as 'top', 'ps', 'w', etc.... A test on a mechin (4096cpu, 256 nodes, 4592 irqs) shows %time cat /proc/stat > /dev/null Before Patch: 12.627 sec After Patch: 2.459 sec Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Tested-by: Jack Steiner <steiner@sgi.com> Acked-by: Jack Steiner <steiner@sgi.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* signals: move cred_guard_mutex from task_struct to signal_structKOSAKI Motohiro2010-10-27
| | | | | | | | | | | | | | | | Oleg Nesterov pointed out we have to prevent multiple-threads-inside-exec itself and we can reuse ->cred_guard_mutex for it. Yes, concurrent execve() has no worth. Let's move ->cred_guard_mutex from task_struct to signal_struct. It naturally prevent multiple-threads-inside-exec. Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Roland McGrath <roland@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* signals: annotate lock_task_sighand()Namhyung Kim2010-10-27
| | | | | | | | | | | | | | | lock_task_sighand() grabs sighand->siglock in case of returning non-NULL but unlock_task_sighand() releases it unconditionally. This leads sparse to complain about the lock context imbalance. Rename and wrap lock_task_sighand() using __cond_lock() macro to make sparse happy. Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Namhyung Kim <namhyung@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Roland McGrath <roland@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* ptrace: change signature of arch_ptrace()Namhyung Kim2010-10-27
| | | | | | | | | | | | | | | Fix up the arguments to arch_ptrace() to take account of the fact that @addr and @data are now unsigned long rather than long as of a preceding patch in this series. Signed-off-by: Namhyung Kim <namhyung@gmail.com> Cc: <linux-arch@vger.kernel.org> Acked-by: Roland McGrath <roland@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* ptrace: change signature of sys_ptrace() and friendsNamhyung Kim2010-10-27
| | | | | | | | | | | | | | | | | Since userspace API of ptrace syscall defines @addr and @data as void pointers, it would be more appropriate to define them as unsigned long in kernel. Therefore related functions are changed also. 'unsigned long' is typically used in other places in kernel as an opaque data type and that using this helps cleaning up a lot of warnings from sparse. Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Namhyung Kim <namhyung@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Roland McGrath <roland@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* cgroup: add clone_children control fileDaniel Lezcano2010-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ns_cgroup is a control group interacting with the namespaces. When a new namespace is created, a corresponding cgroup is automatically created too. The cgroup name is the pid of the process who did 'unshare' or the child of 'clone'. This cgroup is tied with the namespace because it prevents a process to escape the control group and use the post_clone callback, so the child cgroup inherits the values of the parent cgroup. Unfortunately, the more we use this cgroup and the more we are facing problems with it: (1) when a process unshares, the cgroup name may conflict with a previous cgroup with the same pid, so unshare or clone return -EEXIST (2) the cgroup creation is out of control because there may have an application creating several namespaces where the system will automatically create several cgroups in his back and let them on the cgroupfs (eg. a vrf based on the network namespace). (3) the mix of (1) and (2) force an administrator to regularly check and clean these cgroups. This patchset removes the ns_cgroup by adding a new flag to the cgroup and the cgroupfs mount option. It enables the copy of the parent cgroup when a child cgroup is created. We can then safely remove the ns_cgroup as this flag brings a compatibility. We have now to manually create and add the task to a cgroup, which is consistent with the cgroup framework. This patch: Sent as an answer to a previous thread around the ns_cgroup. https://lists.linux-foundation.org/pipermail/containers/2009-June/018627.html It adds a control file 'clone_children' for a cgroup. This control file is a boolean specifying if the child cgroup should be a clone of the parent cgroup or not. The default value is 'false'. This flag makes the child cgroup to call the post_clone callback of all the subsystem, if it is available. At present, the cpuset is the only one which had implemented the post_clone callback. The option can be set at mount time by specifying the 'clone_children' mount option. Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr> Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Paul Menage <menage@google.com> Reviewed-by: Li Zefan <lizf@cn.fujitsu.com> Cc: Jamal Hadi Salim <hadi@cyberus.ca> Cc: Matt Helsley <matthltc@us.ibm.com> Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* fbmem: fix fb_read, fb_write unaligned accessesJames Hogan2010-10-27
| | | | | | | | | | | | | | | | | | | fb_{read,write} access the framebuffer using lots of fb_{read,write}l's but don't check that the file position is aligned which can cause problems on some architectures which do not support unaligned accesses. Since the operations are essentially memcpy_{from,to}io, new fb_memcpy_{from,to}fb macros have been defined and these are used instead. For Sparc, fb_{read,write} macros use sbus_{read,write}, so this defines new sbus_memcpy_{from,to}io functions the same as memcpy_{from,to}io but using sbus_{read,write}b instead of {read,write}b. Signed-off-by: James Hogan <james@albanarts.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* gpio: adp5588-gpio: add i2c forward declarationMichael Hennerich2010-10-27
| | | | | | | | | | | | Some ADP5588 functions take a pointer to an i2c_client, but if the i2c header doesn't happen to be included first, we hit the standard "struct declared inside parameter list" warnings from gcc. So add a simple forward decl of the i2c_client struct. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* gpio: adp5588-gpio: gpio_start must be signedMichael Hennerich2010-10-27
| | | | | | | | | | | Common code interprets this as a signed value (a negative value is used to request dynamic ID allocation), so make sure the platform data has proper types to support that. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* gpio: adp5588-gpio: support interrupt controllerMichael Hennerich2010-10-27
| | | | | | | | | | | Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only level sensitive interrupts are supported. Interrupts provided by this irq_chip must be requested using request_threaded_irq(). Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* gpio: add support for 74x164 serial-in/parallel-out 8-bit shift registerMiguel Gaio2010-10-27
| | | | | | | | | | | | Add support for generic 74x164 serial-in/parallel-out 8-bits shift register. This driver can be used as a GPIO output expander. [akpm@linux-foundation.org: remove unused local `refresh'] Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com> Signed-off-by: Juhos Gabor <juhosg@openwrt.org> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* gpiolib: fix HAVE_GPIO_LIB leftovers in asm-generic/gpio.hAnton Vorontsov2010-10-27
| | | | | | | | | | | | | commit 7444a72effa632fcd8edc566f88 ("gpiolib: allow user-selection") removed HAVE_GPIO_LIB Kconfig symbol, but the header file still uses the name [to confuse readers wrt #ifdef/#else/#endif location]. The real Kconfig symbol nowadays is CONFIG_GPIOLIB. Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* gpio: add driver for basic memory-mapped GPIO controllersAnton Vorontsov2010-10-27
| | | | | | | | | | | | | | | | | | | | | | | The basic GPIO controllers may be found in various on-board FPGA and ASIC solutions that are used to control board's switches, LEDs, chip-selects, Ethernet/USB PHY power, etc. These controllers may not provide any means of pin setup (in/out/open drain). The driver supports: - 8/16/32/64 bits registers; - GPIO controllers with clear/set registers; - GPIO controllers with a single "data" register; - Big endian bits/GPIOs ordering (mostly used on PowerPC). Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: David Brownell <david-b@pacbell.net> Cc: Samuel Ortiz <sameo@linux.intel.com>, Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mm: fix race in kunmap_atomic()Peter Zijlstra2010-10-27
| | | | | | | | | | | | | | | | | | | | | Christoph reported a nice splat which illustrated a race in the new stack based kmap_atomic implementation. The problem is that we pop our stack slot before we're completely done resetting its state -- in particular clearing the PTE (sometimes that's CONFIG_DEBUG_HIGHMEM). If an interrupt happens before we actually clear the PTE used for the last slot, that interrupt can reuse the slot in a dirty state, which triggers a BUG in kmap_atomic(). Fix this by introducing kmap_atomic_idx() which reports the current slot index without actually releasing it and use that to find the PTE and delay the _pop() until after we're completely done. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Reported-by: Christoph Hellwig <hch@infradead.org> Acked-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mm,x86: fix kmap_atomic_push vs ioremap_32.cPeter Zijlstra2010-10-27
| | | | | | | | | | | | | It appears i386 uses kmap_atomic infrastructure regardless of CONFIG_HIGHMEM which results in a compile error when highmem is disabled. Cure this by providing the needed few bits for both CONFIG_HIGHMEM and CONFIG_X86_32. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'drm-core-next' of ↵Linus Torvalds2010-10-26
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6 * 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (476 commits) vmwgfx: Implement a proper GMR eviction mechanism drm/radeon/kms: fix r6xx/7xx 1D tiling CS checker v2 drm/radeon/kms: properly compute group_size on 6xx/7xx drm/radeon/kms: fix 2D tile height alignment in the r600 CS checker drm/radeon/kms/evergreen: set the clear state to the blit state drm/radeon/kms: don't poll dac load detect. gpu: Add Intel GMA500(Poulsbo) Stub Driver drm/radeon/kms: MC vram map needs to be >= pci aperture size drm/radeon/kms: implement display watermark support for evergreen drm/radeon/kms/evergreen: add some additional safe regs v2 drm/radeon/r600: fix tiling issues in CS checker. drm/i915: Move gpu_write_list to per-ring drm/i915: Invalidate the to-ring, flush the old-ring when updating domains drm/i915/ringbuffer: Write the value passed in to the tail register agp/intel: Restore valid PTE bit for Sandybridge after bdd3072 drm/i915: Fix flushing regression from 9af90d19f drm/i915/sdvo: Remove unused encoding member i915: enable AVI infoframe for intel_hdmi.c [v4] drm/i915: Fix current fb blocking for page flip drm/i915: IS_IRONLAKE is synonymous with gen == 5 ... Fix up conflicts in - drivers/gpu/drm/i915/{i915_gem.c, i915/intel_overlay.c}: due to the new simplified stack-based kmap_atomic() interface - drivers/gpu/drm/vmwgfx/vmwgfx_drv.c: added .llseek entry due to BKL removal cleanups.
| * Merge remote branch 'intel/drm-intel-next' of ../drm-next into drm-core-nextDave Airlie2010-10-25
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'intel/drm-intel-next' of ../drm-next: (63 commits) drm/i915: Move gpu_write_list to per-ring drm/i915: Invalidate the to-ring, flush the old-ring when updating domains drm/i915/ringbuffer: Write the value passed in to the tail register agp/intel: Restore valid PTE bit for Sandybridge after bdd3072 drm/i915: Fix flushing regression from 9af90d19f drm/i915/sdvo: Remove unused encoding member i915: enable AVI infoframe for intel_hdmi.c [v4] drm/i915: Fix current fb blocking for page flip drm/i915: IS_IRONLAKE is synonymous with gen == 5 drm/i915: Enable SandyBridge blitter ring drm/i915/ringbuffer: Remove broken intel_fill_struct() drm/i915/ringbuffer: Fix emit batch buffer regression from 8187a2b drm/i915: Copy the updated reloc->presumed_offset back to the user drm/i915: Track objects in global active list (as well as per-ring) drm/i915: Simplify most HAS_BSD() checks drm/i915: cache the last object lookup during pin_and_relocate() drm/i915: Do interrupible mutex lock first to avoid locking for unreference drivers: gpu: drm: i915: Fix a typo. agp/intel: Also add B43.1 to list of supported devices drm/i915: rearrange mutex acquisition for pread ...
| | * drm/i915: Enable SandyBridge blitter ringChris Wilson2010-10-21
| | | | | | | | | | | | | | | | | | | | | | | | Based on an original patch by Zhenyu Wang, this initializes the BLT ring for SandyBridge and enables support for user execbuffers. Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
| | * drm/edid: add helper function to detect monitor audio capabilityZhenyu Wang2010-10-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To help to determine if digital display port needs to enable audio output or not. This one adds a helper to get monitor's audio capability via EDID CEA extension block. Tested-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
| | * Merge remote branch 'airlied/drm-core-next' into tmpChris Wilson2010-10-19
| | |\
| | * | drm/i915: fetch eDP configuration data from the VBTJesse Barnes2010-10-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We need to use some of these values in eDP configurations, so be sure to fetch them and store them in the i915 private structure. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
| * | | drm/ttm: Avoid using the ttm_mem_type_manager::put_locked functionThomas Hellstrom2010-10-20
| | |/ | |/| | | | | | | | | | | | | | | | Release the lru spinlock early. Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
| * | drm, kdb, kms: Change mode_set_base_atomic() enter argument to be an enumJason Wessel2010-10-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The enter argument as implemented by commit 413d45d3627 (drm, kdb, kms: Add an enter argument to mode_set_base_atomic() API) should be more descriptive as to what it does vs just passing 1 and 0 around. There is no runtime behavior change as a result of this patch. Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> CC: David Airlie <airlied@linux.ie> CC: dri-devel@lists.freedesktop.org Signed-off-by: Dave Airlie <airlied@redhat.com>
| * | drm/ttm: add unlocked variant of new manager put node.Dave Airlie2010-10-18
| | | | | | | | | | | | | | | | | | | | | We need the unlocked variant for the new codepath introduced to fix the race condition in master recently. Signed-off-by: Dave Airlie <airlied@redhat.com>
| * | Merge branch 'drm-fixes' of /home/airlied/kernel/linux-2.6 into drm-core-nextDave Airlie2010-10-18
| |\ \ | | |/ | |/| | | | | | | | | | | | | Conflicts: drivers/gpu/drm/i915/intel_fb.c drivers/gpu/drm/radeon/r600_blit_kms.c drivers/gpu/drm/ttm/ttm_bo.c
| * | Merge branch 'drm-kdb-next' into drm-core-nextDave Airlie2010-10-05
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * drm-kdb-next: drm/nouveau/kms: Avoid a hang entering KDB with VT accel on. radeon, kdb, kms: Save and restore the LUT on atomic KMS enter/exit drm, kdb, kms: Add an enter argument to mode_set_base_atomic() API drm/nouveau/kms: Implement KDB debug hooks for nouveau KMS. drm/radeon/kms: Implement KDB debug hooks for radeon KMS.
| | * | drm, kdb, kms: Add an enter argument to mode_set_base_atomic() APIJason Wessel2010-10-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some devices such as the radeon chips receive information from user space which needs to be saved when executing an atomic mode set operation, else the user space would have to be queried again for the information. This patch extends the mode_set_base_atomic() call to pass an argument to indicate if this is an entry or an exit from an atomic kernel mode set change. Individual drm drivers can properly save and restore state accordingly. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> CC: Jesse Barnes <jbarnes@virtuousgeek.org> CC: David Airlie <airlied@linux.ie> CC: dri-devel@lists.freedesktop.org Signed-off-by: Dave Airlie <airlied@redhat.com>
| * | | Merge remote branch 'nouveau/for-airlied' of ../drm-nouveau-next into ↵Dave Airlie2010-10-05
| |\ \ \ | | |/ / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | drm-core-next [airlied - add fix for vmwgfx build] * 'nouveau/for-airlied' of ../drm-nouveau-next: (93 commits) drm/ttm: restructure to allow driver to plug in alternate memory manager drm/ttm: introduce utility function to free an allocated memory node drm/nouveau: fix thinkos in mem timing table recordlen check drm/nouveau: parse voltage from perf 0x40 entires drm/nouveau: don't use the default pll limits in table v2.1 on nv50+ cards drm/nv50: Fix large 3D performance regression caused by the interchannel sync patches. drm/nouveau: Synchronize buffer object moves in hardware. drm/nouveau: Use semaphores to handle inter-channel sync in hardware. drm/nouveau: Provide a means to have arbitrary work run on fence completion. drm/nouveau: Minor refactoring/cleanup of the fence code. drm/nouveau: Add a module option to force card POST. drm/nv50: prevent (IB_PUT == IB_GET) for occurring unless idle drm/nv0x-nv4x: Leave the 0x40 bit untouched when changing CRE_LCD. drm/nv30-nv40: Fix postdivider mask when writing engine/memory PLLs. drm/nouveau: Fix perf table parsing on BMP v5.25. drm/nouveau: fix required mode bandwidth calculation for DP drm/nouveau: fix typo in c2aa91afea5f7e7ae4530fabd37414a79c03328c drm/nva3: split pm backend out from nv50 drm/nouveau: run perflvl and M table scripts on mem clock change drm/nouveau: pass perflvl struct to clock_pre() ...
| | * | drm/ttm: restructure to allow driver to plug in alternate memory managerBen Skeggs2010-10-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Nouveau will need this on GeForce 8 and up to account for the GPU reordering physical VRAM for some memory types. Reviewed-by: Jerome Glisse <jglisse@redhat.com> Acked-by: Thomas Hellström <thellstrom@vmware.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
| | * | drm/ttm: introduce utility function to free an allocated memory nodeBen Skeggs2010-10-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Existing core code/drivers call drm_mm_put_block on ttm_mem_reg.mm_node directly. Future patches will modify TTM behaviour in such a way that ttm_mem_reg.mm_node doesn't necessarily belong to drm_mm. Reviewed-by: Jerome Glisse <jglisse@redhat.com> Acked-by: Thomas Hellström <thellstrom@vmware.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
| * | | drm/vmwgfx: Add a parameter to get the max fb sizeThomas Hellstrom2010-10-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This can be used by the X server to restrict mode resolutions and size of root pixmap. Bump minor to announce this availability. Bump driver date. Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
| * | | drm: vmwgfx: Add a struct drm_file parameter to the dirty framebuffer callbackThomas Hellstrom2010-10-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is needed for the callback to identify the caller and take appropriate locks if needed. Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
| * | | Merge remote branch 'korg/drm-fixes' into drm-vmware-nextDave Airlie2010-10-05
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | necessary for some of the vmware fixes to be pushed in. Conflicts: drivers/gpu/drm/drm_gem.c drivers/gpu/drm/i915/intel_fb.c include/drm/drmP.h
| * \ \ \ Merge remote branch 'intel/drm-intel-next' of ../drm-next into drm-core-nextDave Airlie2010-10-05
| |\ \ \ \ | | |_|/ / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'intel/drm-intel-next' of ../drm-next: (266 commits) drm/i915: Avoid circular locking from intel_fbdev_fini() drm/i915: mark display port DPMS state as 'ON' when enabling output drm/i915: Skip pread/pwrite if size to copy is 0. drm/i915: avoid struct mutex output_poll mutex lock loop on unload drm/i915: Rephrase pwrite bounds checking to avoid any potential overflow drm/i915: Sanity check pread/pwrite drm/i915: Use pipe state to tell when pipe is off drm/i915: vblank status not valid while training display port drivers/gpu/drm/i915/i915_gem.c: Add missing error handling code drm/i915: Don't mask the return code whilst relocating. drm/i915: If the GPU hangs twice within 5 seconds, declare it wedged. drm/i915: Only print 'generating error event' if we actually are drm/i915: Try to reset gen2 devices. drm/i915: Clear fence registers on GPU reset drm/i915: Force the domain to CPU on unbinding whilst wedged. drm: Move the GTT accounting to i915 drm/i915: Fix refleak during eviction. i915: Added function to initialize VBT settings drm/i915: Remove redundant deletion of obj->gpu_write_list drm/i915: Make get/put pages static ...
| | * | | drm: Move the GTT accounting to i915Chris Wilson2010-10-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Only drm/i915 does the bookkeeping that makes the information useful, and the information maintained is driver specific, so move it out of the core and into its single user. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Dave Airlie <airlied@redhat.com>
| | * | | intel-gtt: clean up gtt size reportingDaniel Vetter2010-09-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Consolidate everything in intel-gtt.c and also kill the export of intel_max_stolen. Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
| | * | | Merge branch 'drm-intel-fixes' into HEADChris Wilson2010-09-21
| | |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/char/agp/intel-agp.c drivers/gpu/drm/i915/intel_crt.c
| | * | | | drm/i915: die, i915_probe_agp, dieDaniel Vetter2010-09-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the detection from intel-gtt.ko instead. Hooray! Also move the stolen mem allocator to the other gtt stuff in dev_prv->mem. v2: Chris Wilson noted that my error handling was crap. Fix it. He also said that this fixes a problem on his i845. Indeed, i915_probe_agp misses a special case for i830/i845 stolen mem detection. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=25476 Cc: stable@kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
| | * | | | intel-gtt: introduce drm/intel-gtt.hDaniel Vetter2010-09-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a few definitions to it that are already shared and that will be shared in the future (like the number of stolen entries). No functional changes in here. Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
| | * | | | Merge remote branch 'airlied/drm-core-next' into HEADChris Wilson2010-09-08
| | |\ \ \ \
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-30 06:42:01 -0500