| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
currently the export_operation structure and helpers related to it are in
fs.h. fs.h is already far too large and there are very few places needing the
export bits, so split them off into a separate header.
[akpm@linux-foundation.org: fix cifs build]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
| |
The CAPI 2.0 driver uses a semaphore as mutex. Use the mutex API instead of
the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Quicc Engine enabled mpc83xx CPU's has a somewhat different HW interface to
the SPI controller. This patch adds a qe_mode knob that sees to that
needed adaptions are performed.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Add support for the Infineon TLE62x0 series of low-side driver chips, such
as the TLE6220 or TLE6230. These can be viewed as output GPIOs specialized
for power switching applications. The driver provides a userspace
interface to those GPIOs, and to the switch status they provide.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Add CRC7 routines, used for example in MMC over SPI communication.
Kerneldoc updates
[akpm@linux-foundation.org: fix funny mix of const and non-const]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
| |
Add a new spi->mode bit: SPI_3WIRE, for chips where the SI and SO signals
are shared (and which are thus only half duplex). Update the LM70 driver
to require support for that hardware mode from the controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Minor SPI controller driver updates: make the setup() methods reject
spi->mode bits they don't support, by masking aginst the inverse of bits
they *do* support. This insures against misbehavior later when new mode
bits get added.
Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH.
Support for all four SPI clock/transfer modes is routine.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Make arguments of timespec_equal() const struct timespec.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
KSYM_NAME_LEN is peculiar in that it does not include the space for the
trailing '\0', forcing all users to use KSYM_NAME_LEN + 1 when allocating
buffer. This is nonsense and error-prone. Moreover, when the caller
forgets that it's very likely to subtly bite back by corrupting the stack
because the last position of the buffer is always cleared to zero.
This patch increments KSYM_NAME_LEN by one and updates code accordingly.
* off-by-one bug in asm-powerpc/kprobes.h::kprobe_lookup_name() macro
is fixed.
* Where MODULE_NAME_LEN and KSYM_NAME_LEN were used together,
MODULE_NAME_LEN was treated as if it didn't include space for the
trailing '\0'. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Paulo Marques <pmarques@grupopie.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This is a driver for the SB1250 DUART, a dual serial port implementation
included in the Broadcom family of SOCs descending from the SiByte SB1250
MIPS64 chip multiprocessor. It is a new implementation replacing the
old-fashioned driver currently present in the linux-mips.org tree. It
supports all the usual features one would expect from a(n asynchronous)
serial driver, including modem line control (as far as hardware supports it
-- there is edge detection logic missing from the DCD and RI lines and the
driver does not implement polling of these lines at the moment), the serial
console, BREAK transmission and reception, including the magic SysRq. The
receive FIFO threshold is not maintained though.
The driver was tested with a SWARM board which uses a BCM1250 SOC (which is
dual MIPS64 CMP) and has both ports of the single DUART implemented wired
externally. Both were tested. Testing included using the ports as
terminal lines at 1200bps (which is the ports minimum), 115200bps and a
couple of random speeds inbetween. The modem lines were verified to
operate correctly. No testing was performed with a use as a network
interface, like with SLIP or PPP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The CHILD_MAX macro in limits.h should not be there. It claims to be the
limit on processes a user can own, but its value is wrong for that.
There is no constant value, but a variable resource limit (RLIMIT_NPROC).
Nothing in the kernel uses CHILD_MAX.
The proper thing to do according to POSIX is not to define CHILD_MAX at all.
The sysconf (_SC_CHILD_MAX) implementation works by calling getrlimit.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The OPEN_MAX macro in limits.h should not be there. It claims to be the
limit on file descriptors in a process, but its value is wrong for that.
There is no constant value, but a variable resource limit (RLIMIT_NOFILE).
Nothing in the kernel uses OPEN_MAX except things that are wrong to do so.
I've submitted other patches to remove those uses.
The proper thing to do according to POSIX is not to define OPEN_MAX at all.
The sysconf (_SC_OPEN_MAX) implementation works by calling getrlimit.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
| |
Put WARN_ON and fixed all callers of unregister_blkdev(). Now we can make
unregister_blkdev return void.
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
| |
Add a proper prototype for proc_nr_files() in include/linux/fs.h
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Identical implementations of PTRACE_POKEDATA go into generic_ptrace_pokedata()
function.
AFAICS, fix bug on xtensa where successful PTRACE_POKEDATA will nevertheless
return EPERM.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Identical implementations of PTRACE_PEEKDATA go into generic_ptrace_peekdata()
function.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
If the kernel OOPSed or BUGed then it probably should be considered as
tainted. Thus, all subsequent OOPSes and SysRq dumps will report the
tainted kernel. This saves a lot of time explaining oddities in the
calltraces.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Added parisc patch from Matthew Wilson -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The bounce buffer logic is included on systems that do not need it. If a
system does not have zones like ZONE_DMA and ZONE_HIGHMEM that can lead to
the use of bounce buffers then there is no need to reserve memory pools etc
etc. This is true f.e. for SGI Altix.
Also nicifies the Makefile and gets rid of the tricky "and" there.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Detect slab objects being passed to the page oriented functions of the VM.
It is not sufficient to simply return NULL because the functions calling
page_mapping may depend on other items of the page_struct also to be setup
properly. Moreover slab object may not be properly aligned. The page
oriented functions of the VM expect to operate on page aligned, page sized
objects. Operations on object straddling page boundaries may only affect the
objects partially which may lead to surprising results.
It is better to detect eventually remaining uses and eliminate them.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
It becomes now easy to support the zeroing allocs with generic inline
functions in slab.h. Provide inline definitions to allow the continued use of
kzalloc, kmem_cache_zalloc etc but remove other definitions of zeroing
functions from the slab allocators and util.c.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Add #ifdefs around data structures only needed if debugging is compiled into
SLUB.
Add inlines to small functions to reduce code size.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Define ZERO_OR_NULL_PTR macro to be able to remove the checks from the
allocators. Move ZERO_SIZE_PTR related stuff into slab.h.
Make ZERO_SIZE_PTR work for all slab allocators and get rid of the
WARN_ON_ONCE(size == 0) that is still remaining in SLAB.
Make slub return NULL like the other allocators if a too large memory segment
is requested via __kmalloc.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
I can never remember what the function to register to receive VM pressure
is called. I have to trace down from __alloc_pages() to find it.
It's called "set_shrinker()", and it needs Your Help.
1) Don't hide struct shrinker. It contains no magic.
2) Don't allocate "struct shrinker". It's not helpful.
3) Call them "register_shrinker" and "unregister_shrinker".
4) Call the function "shrink" not "shrinker".
5) Reduce the 17 lines of waffly comments to 13, but document it properly.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: David Chinner <dgc@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When we are out of memory of a suitable size we enter reclaim. The current
reclaim algorithm targets pages in LRU order, which is great for fairness at
order-0 but highly unsuitable if you desire pages at higher orders. To get
pages of higher order we must shoot down a very high proportion of memory;
>95% in a lot of cases.
This patch set adds a lumpy reclaim algorithm to the allocator. It targets
groups of pages at the specified order anchored at the end of the active and
inactive lists. This encourages groups of pages at the requested orders to
move from active to inactive, and active to free lists. This behaviour is
only triggered out of direct reclaim when higher order pages have been
requested.
This patch set is particularly effective when utilised with an
anti-fragmentation scheme which groups pages of similar reclaimability
together.
This patch set is based on Peter Zijlstra's lumpy reclaim V2 patch which forms
the foundation. Credit to Mel Gorman for sanitity checking.
Mel said:
The patches have an application with hugepage pool resizing.
When lumpy-reclaim is used used with ZONE_MOVABLE, the hugepages pool can
be resized with greater reliability. Testing on a desktop machine with 2GB
of RAM showed that growing the hugepage pool with ZONE_MOVABLE on it's own
was very slow as the success rate was quite low. Without lumpy-reclaim,
each attempt to grow the pool by 100 pages would yield 1 or 2 hugepages.
With lumpy-reclaim, getting 40 to 70 hugepages on each attempt was typical.
[akpm@osdl.org: ia64 pfn_to_nid fixes and loop cleanup]
[bunk@stusta.de: static declarations for internal functions]
[a.p.zijlstra@chello.nl: initial lumpy V2 implementation]
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the kernelcore= parameter for x86.
Once all patches are applied, a new command-line parameter exist and a new
sysctl. This patch adds the necessary documentation.
From: Yasunori Goto <y-goto@jp.fujitsu.com>
When "kernelcore" boot option is specified, kernel can't boot up on ia64
because of an infinite loop. In addition, the parsing code can be handled
in an architecture-independent manner.
This patch uses common code to handle the kernelcore= parameter. It is
only available to architectures that support arch-independent zone-sizing
(i.e. define CONFIG_ARCH_POPULATES_NODE_MAP). Other architectures will
ignore the boot parameter.
[bunk@stusta.de: make cmdline_parse_kernelcore() static]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Huge pages are not movable so are not allocated from ZONE_MOVABLE. However,
as ZONE_MOVABLE will always have pages that can be migrated or reclaimed, it
can be used to satisfy hugepage allocations even when the system has been
running a long time. This allows an administrator to resize the hugepage pool
at runtime depending on the size of ZONE_MOVABLE.
This patch adds a new sysctl called hugepages_treat_as_movable. When a
non-zero value is written to it, future allocations for the huge page pool
will use ZONE_MOVABLE. Despite huge pages being non-movable, we do not
introduce additional external fragmentation of note as huge pages are always
the largest contiguous block we care about.
[akpm@linux-foundation.org: various fixes]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The following 8 patches against 2.6.20-mm2 create a zone called ZONE_MOVABLE
that is only usable by allocations that specify both __GFP_HIGHMEM and
__GFP_MOVABLE. This has the effect of keeping all non-movable pages within a
single memory partition while allowing movable allocations to be satisfied
from either partition. The patches may be applied with the list-based
anti-fragmentation patches that groups pages together based on mobility.
The size of the zone is determined by a kernelcore= parameter specified at
boot-time. This specifies how much memory is usable by non-movable
allocations and the remainder is used for ZONE_MOVABLE. Any range of pages
within ZONE_MOVABLE can be released by migrating the pages or by reclaiming.
When selecting a zone to take pages from for ZONE_MOVABLE, there are two
things to consider. First, only memory from the highest populated zone is
used for ZONE_MOVABLE. On the x86, this is probably going to be ZONE_HIGHMEM
but it would be ZONE_DMA on ppc64 or possibly ZONE_DMA32 on x86_64. Second,
the amount of memory usable by the kernel will be spread evenly throughout
NUMA nodes where possible. If the nodes are not of equal size, the amount of
memory usable by the kernel on some nodes may be greater than others.
By default, the zone is not as useful for hugetlb allocations because they are
pinned and non-migratable (currently at least). A sysctl is provided that
allows huge pages to be allocated from that zone. This means that the huge
page pool can be resized to the size of ZONE_MOVABLE during the lifetime of
the system assuming that pages are not mlocked. Despite huge pages being
non-movable, we do not introduce additional external fragmentation of note as
huge pages are always the largest contiguous block we care about.
Credit goes to Andy Whitcroft for catching a large variety of problems during
review of the patches.
This patch creates an additional zone, ZONE_MOVABLE. This zone is only usable
by allocations which specify both __GFP_HIGHMEM and __GFP_MOVABLE. Hot-added
memory continues to be placed in their existing destination as there is no
mechanism to redirect them to a specific zone.
[y-goto@jp.fujitsu.com: Fix section mismatch of memory hotplug related code]
[akpm@linux-foundation.org: various fixes]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
be migrated
It is often known at allocation time whether a page may be migrated or not.
This patch adds a flag called __GFP_MOVABLE and a new mask called
GFP_HIGH_MOVABLE. Allocations using the __GFP_MOVABLE can be either migrated
using the page migration mechanism or reclaimed by syncing with backing
storage and discarding.
An API function very similar to alloc_zeroed_user_highpage() is added for
__GFP_MOVABLE allocations called alloc_zeroed_user_highpage_movable(). The
flags used by alloc_zeroed_user_highpage() are not changed because it would
change the semantics of an existing API. After this patch is applied there
are no in-kernel users of alloc_zeroed_user_highpage() so it probably should
be marked deprecated if this patch is merged.
Note that this patch includes a minor cleanup to the use of __GFP_ZERO in
shmem.c to keep all flag modifications to inode->mapping in the
shmem_dir_alloc() helper function. This clean-up suggestion is courtesy of
Hugh Dickens.
Additional credit goes to Christoph Lameter and Linus Torvalds for shaping the
concept. Credit to Hugh Dickens for catching issues with shmem swap vector
and ramfs allocations.
[akpm@linux-foundation.org: build fix]
[hugh@veritas.com: __GFP_ZERO cleanup]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (209 commits)
[POWERPC] Create add_rtc() function to enable the RTC CMOS driver
[POWERPC] Add H_ILLAN_ATTRIBUTES hcall number
[POWERPC] xilinxfb: Parameterize xilinxfb platform device registration
[POWERPC] Oprofile support for Power 5++
[POWERPC] Enable arbitary speed tty ioctls and split input/output speed
[POWERPC] Make drivers/char/hvc_console.c:khvcd() static
[POWERPC] Remove dead code for preventing pread() and pwrite() calls
[POWERPC] Remove unnecessary #undef printk from prom.c
[POWERPC] Fix typo in Ebony default DTS
[POWERPC] Check for NULL ppc_md.init_IRQ() before calling
[POWERPC] Remove extra return statement
[POWERPC] pasemi: Don't auto-select CONFIG_EMBEDDED
[POWERPC] pasemi: Rename platform
[POWERPC] arch/powerpc/kernel/sysfs.c: Move NUMA exports
[POWERPC] Add __read_mostly support for powerpc
[POWERPC] Modify sched_clock() to make CONFIG_PRINTK_TIME more sane
[POWERPC] Create a dummy zImage if no valid platform has been selected
[POWERPC] PS3: Bootwrapper support.
[POWERPC] powermac i2c: Use mutex
[POWERPC] Schedule removal of arch/ppc
...
Fixed up conflicts manually in:
Documentation/feature-removal-schedule.txt
arch/powerpc/kernel/pci_32.c
arch/powerpc/kernel/pci_64.c
include/asm-powerpc/pci.h
and asked the powerpc people to double-check the result..
|
| | |\ |
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Adds support for PowerQuicc on-chip PCMCIA. The driver is implemented as
of_device, so only arch/powerpc stuff is capable to use it, which now implies
only mpc885ads reference board.
To cope with the code that should be hooked inside driver, but is really board
specific (like set_voltage), global structure mpc8xx_pcmcia_ops holds
necessary function pointers that are filled in the BSP code.
[akpm@linux-foundation.org: whitespace diddles]
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This makes unmap_vm_area static and a wrapper around a new
exported unmap_kernel_range that takes an explicit range instead
of a vm_area struct.
This makes it more versatile for code that wants to play with kernel
page tables outside of the standard vmalloc area.
(One example is some rework of the PowerPC PCI IO space mapping
code that depends on that patch and removes some code duplication
and horrible abuse of forged struct vm_struct).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This reverts commit 29578624e354f56143d92510fff33a8b2aaa2c03.
Ingo Molnar reports complete breakage with his e1000 card (no
networking, card reports transmit timeouts), and bisected it down to
this commit. Let's figure out what went wrong, but not keep breaking
machines until we do.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Olaf Kirch <olaf.kirch@oracle.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (32 commits)
[PATCH] ocfs2: zero_user_page conversion
ocfs2: Support xfs style space reservation ioctls
ocfs2: support for removing file regions
ocfs2: update truncate handling of partial clusters
ocfs2: btree support for removal of arbirtrary extents
ocfs2: Support creation of unwritten extents
ocfs2: support writing of unwritten extents
ocfs2: small cleanup of ocfs2_write_begin_nolock()
ocfs2: btree changes for unwritten extents
ocfs2: abstract btree growing calls
ocfs2: use all extent block suballocators
ocfs2: plug truncate into cached dealloc routines
ocfs2: simplify deallocation locking
ocfs2: harden buffer check during mapping of page blocks
ocfs2: shared writeable mmap
ocfs2: factor out write aops into nolock variants
ocfs2: rework ocfs2_buffered_write_cluster()
ocfs2: take ip_alloc_sem during entire truncate
ocfs2: Add "preferred slot" mount option
[KJ PATCH] Replacing memset(<addr>,0,PAGE_SIZE) with clear_page() in fs/ocfs2/dlm/dlmrecovery.c
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Sometimes other drivers depend on particular configfs items. For
example, ocfs2 mounts depend on a heartbeat region item. If that
region item is removed with rmdir(2), the ocfs2 mount must BUG or go
readonly. Not happy.
This provides two additional API calls: configfs_depend_item() and
configfs_undepend_item(). A client driver can call
configfs_depend_item() on an existing item to tell configfs that it is
depended on. configfs will then return -EBUSY from rmdir(2) for that
item. When the item is no longer depended on, the client driver calls
configfs_undepend_item() on it.
These API cannot be called underneath any configfs callbacks, as
they will conflict. They can block and allocate. A client driver
probably shouldn't calling them of its own gumption. Rather it should
be providing an API that external subsystems call.
How does this work? Imagine the ocfs2 mount process. When it mounts,
it asks for a heart region item. This is done via a call into the
heartbeat code. Inside the heartbeat code, the region item is looked
up. Here, the heartbeat code calls configfs_depend_item(). If it
succeeds, then heartbeat knows the region is safe to give to ocfs2.
If it fails, it was being torn down anyway, and heartbeat can gracefully
pass up an error.
[ Fixed some bad whitespace in configfs.txt. --Mark ]
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add a notification callback, ops->disconnect_notify(). It has the same
prototype as ->drop_item(), but it will be called just before the item
linkage is broken. This way, configfs users who want to do work while
the object is still in the heirarchy have a chance.
Client drivers will still need to config_item_put() in their
->drop_item(), if they implement it. They need do nothing in
->disconnect_notify(). They don't have to provide it if they don't
care. But someone who wants to be notified before ci_parent is set to
NULL can now be notified.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Convert the su_sem member of struct configfs_subsystem to a struct
mutex, as that's what it is. Also convert all the users and update
Documentation/configfs.txt and Documentation/configfs_example.c
accordingly.
[ Conflict in fs/dlm/config.c with commit
3168b0780d06ace875696f8a648d04d6089654e5 manually resolved. --Mark ]
Inspired-by: Satyam Sharma <ssatyam@cse.iitk.ac.in>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Configfs being based upon sysfs code, config_group_find_obj() is probably
so named because of the similar kset_find_obj() in sysfs. However,
"kobject"s in sysfs become "config_item"s in configfs, so let's call it
config_group_find_item() instead, for sake of uniformity, and make
corresponding change in the users of this function.
BTW a crucial difference between kset_find_obj and config_group_find_item
is in locking expectations. kset_find_obj does its locking by itself, but
config_group_find_item expects the *caller* to do the locking. The reason
for this: kset's have their own locks, config_group's don't but instead
rely on the subsystem mutex. And, subsystem needn't necessarily be around
when config_group_find_item() is called.
So let's state these locking semantics explicitly, and rectify the comment,
otherwise bugs could continue to occur in future, as they did in the past
(refer commit d82b8191e238 in gfs2-2.6-fixes.git).
[ I also took the opportunity to fix some bad whitespace and
double-empty lines. --Joel ]
[ Conflict in fs/dlm/config.c with commit
3168b0780d06ace875696f8a648d04d6089654e5 manually resolved. --Mark ]
Signed-off-by: Satyam Sharma <ssatyam@cse.iitk.ac.in>
Cc: David Teigland <teigland@redhat.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
fs/dlm/config.c contains a useful generic macro called __CONFIGFS_ATTR
that is similar to sysfs' __ATTR macro that makes defining attributes
easy for any user of configfs. Separate it out into configfs.h so that
other users (forthcoming in dynamic netconsole patchset) can use it too.
Signed-off-by: Satyam Sharma <ssatyam@cse.iitk.ac.in>
Cc: David Teigland <teigland@redhat.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
1. item.c:config_item_cleanup() is a private function (only called by
config_item_release() in same file). However, it is spuriously
exported in include/linux/configfs.h, so remove that export and make
it static in item.c. Also, it is no longer exported / interface
function, so no need to give comment for this function (the comment
was stating obvious thing, anyway).
2. Kernel-doc comment format does not allow empty line between end of
comment and start of function (declaration line). There were several
such spurious empty lines in item.c, so fix them.
fs/configfs/item.c | 15 +++------------
include/linux/configfs.h | 1 -
2 files changed, 3 insertions(+), 13 deletions(-)
Signed-off-by: Satyam Sharma <ssatyam@cse.iitk.ac.in>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
* 'bsg' of git://git.kernel.dk/data/git/linux-2.6-block: (25 commits)
bsg: Kconfig updates
bsg: add SCSI transport-level request support
bsg: add bidi support
add a struct request pointer to the request structure
bsg: fix the deadlock on discarding done commands
bsg: fix a blocking read bug
bsg: minor bug fixes
improve bsg device allocation
bind bsg to all SCSI devices
bsg: bind bsg to request_queue instead of gendisk
bsg: add a request_queue argument to scsi_cmd_ioctl()
bsg: simplify __bsg_alloc_command failpath
bsg: add cheasy error checks for sysfs stuff
Add queue resizing support
Replace s32, u32 and u64 with __s32, __u32 and __u64 in bsg.h for userspace
bsg: silence a bogus gcc warning
bsg: style cleanup
bsg: use u32 etc instead of uint32_t
bsg: add SG_IO to SG v4
bsg: replace SG v3 with SG v4
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This enables bsg to handle SCSI transport-level request like SAS
management protocol (SMP).
- add BSG_SUB_PROTOCOL_{SCSI_CMD, SCSI_TMF, SCSI_TRANSPORT} definitions.
- SCSI transport-level requests skip blk_verify_command().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This adds a struct request pointer to the request structure for the
second data phase (bidi for now). A request queue supporting bidi
requests sets QUEUE_FLAG_BIDI. This prevents sending bidi requests to
a non-bidi queue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This fixes the following minor issues:
- add EXPORT_SYMBOL_GPL for bsg_register_queue and
bsg_unregister_queue.
- shut up gcc warnings
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <axboe@nelson.home.kernel.dk>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This patch binds bsg devices to request_queue instead of gendisk. Any
objects (like transport entities) can define own request_handler and
create own bsg device.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
bsg uses scsi_cmd_ioctl() for some SCSI/sg ioctl
commands. scsi_cmd_ioctl() gets a request queue from a gendisk
arguement. This prevents bsg being bound to SCSI devices that don't
have a gendisk (like OSD). This adds a request_queue argument to
scsi_cmd_ioctl(). The SCSI/sg ioctl commands doesn't use a gendisk so
it's safe for any SCSI devices to use scsi_cmd_ioctl().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| | | | | |
| | | | |
| | | | |
| | | | | |
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This patch adds sg_io_v4 structure that Doug proposed last month.
There's one major change from the RFC. I dropped iovec, which needs
compat stuff. The bsg code simply calls blk_rq_map_user against
dout_xferp/din_xferp. So if possible, the page frames are directly
mapped. If not possible, the block layer allocates new page frames and
does memory copies.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
