aboutsummaryrefslogtreecommitdiffstats
path: root/include/linux/mmc
Commit message (Collapse)AuthorAge
* mmc: sdhci: Add quirk for always getting TC with stop cmdAdrian Hunter2014-10-03
| | | | | | | | | Add a quirk for a host controller that always sets a Transfer Complete interrupt status for the stop command even when a busy response is not indicated. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: restore detect line inversion semanticsLinus Walleij2014-10-02
| | | | | | | | | | | | | | | | | | | | commit 98e90de99a0c43bd434da814c882c4332441871e "mmc: host: switch OF parser to use gpio descriptors" switched the semantic behaviour of card detect and read only flags such that the inversion capability flag would only be set if inversion was explicitly specified in the device tree, in the hopes that no-one was using double inversion. It turns out that the XOR:ing between the explicit inversion was indeed in use, so we need to restore the old semantics where both ways of inversion are checked and the end result XOR:ed. Reported-by: Javier Martinez Canillas <javier@dowhile0.org> Tested-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: Add new power_mode MMC_POWER_UNDEFINEDRoger Tseng2014-09-24
| | | | | | | | | | | | | Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as the initial value of host->ios.power_mode. For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later mmc_power_off() do real power-off things instead of NOP, and further prevents state messed up in cards that was already initialized (eg. by BIOS of UEFI driver). Signed-off-by: Roger Tseng <rogerable@realtek.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: Consolidate emmc tuning blocksStephen Boyd2014-09-23
| | | | | | | | | | The same tuning block exists in the dw_mmc h.c and sdhci-msm.c files. Move these into mmc.c so that they can be shared across drivers. Reported-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: Replace "enhanced_area_en" attribute by "partition_setting_completed"Grégory Soutadé2014-09-18
| | | | | | | | | | Replace ext_csd "enhanced_area_en" attribute by "partition_setting_completed". It was used whether or not enhanced user area is defined and without checks of EXT_CSD_PARTITION_SETTING_COMPLETED bit. Signed-off-by: Grégory Soutadé <gsoutade@neotion.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: slot-gpio: add gpiod variant to get wp GPIOLinus Walleij2014-09-09
| | | | | | | | | | This makes it possible to get the write protect (read only) GPIO line from a GPIO descriptor. Written to exactly mirror the card detect function. Acked-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: remove MMC_CAP2_NO_MULTI_READ flagsKuninori Morimoto2014-09-09
| | | | | | | | | Now, mmc framework uses multi_io_quirk for I/O HW bug workaround. MMC_CAP2_NO_MULTI_READ flag is no longer needed Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: Add .multi_io_quirk callback for multi I/O HW bugKuninori Morimoto2014-09-09
| | | | | | | | | | | | | | | | Historically, we have been using MMC_CAP* to handle host HW issues and currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi I/O HW bug workaround. There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all situations. Therefore let's add an optional host ops callback to enable host drivers to return the number of blocks it allows per request. In a future patch and when host drivers have converted to the new callback, MMC_CAP2_NO_MULTI_READ shall be removed. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci: handle busy-end interrupt during commandChanho Min2014-09-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | It is fully legal for a controller to start handling busy-end interrupt before it has signaled that the command has completed. So make sure we do things in the proper order, Or it results that command interrupt is ignored so it can cause unexpected operations. This is founded at some toshiba emmc with the bellow warning. "mmc0: Got command interrupt 0x00000001 even though no command operation was in progress." This issue has been also reported by Youssef TRIKI: It is not specific to Toshiba devices, and happens with eMMC devices as well as SD card which support Auto-CMD12 rather than CMD23. Also, similar patch is submitted by: Gwendal Grignou <gwendal@chromium.org> Changes since v1: Fixed conflict with the next of git.linaro.org/people/ulf.hansson/mmc.git and Tested if issue is fixed again. Signed-off-by: Hankyung Yu <hankyung.yu@lge.com> Signed-off-by: Chanho Min <chanho.min@lge.com> Tested-by: Youssef TRIKI <youssef.triki@st.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Support voltage changesDoug Anderson2014-09-09
| | | | | | | | | | | | For UHS cards we need the ability to switch voltages from 3.3V to 1.8V. Add support to the dw_mmc driver to handle this. Note that dw_mmc needs a little bit of extra code since the interface needs a special bit programmed to the CMD register while CMD11 is progressing. This means adding a few extra states to the state machine to track. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: use mmc_regulator_get_supply to handle regulatorsYuvaraj CD2014-09-09
| | | | | | | | | | | This patch makes use of mmc_regulator_get_supply() to handle the vmmc and vqmmc regulators.Also it moves the code handling the these regulators to dw_mci_set_ios().It turned on the vmmc and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off during MMC_POWER_OFF. Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: implement Driver Stage Register handlingSascha Hauer2014-09-09
| | | | | | | | | | | | | | | | | | | | Some eMMC and SD cards implement a DSR register that allows to tune raise/fall times and drive strength of the CMD and DATA outputs. The values to use depend on the card in use and the host. It might be needed to reduce the drive strength to prevent voltage peaks above the host's specification. Implement a 'dsr' devicetree property that allows to specify the value to set the DSR to. For non-dt setups the new members of mmc_host can be set by board code. This patch was initially authored by Sascha Hauer. It contains improvements authored by Markus Niebel and Uwe Kleine-König. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: Correct the value of MMC_NUM_PHY_PARTITIONYi Sun2014-09-09
| | | | | | | | | eMMC card can support up to 7 physical partitions, including 2 boot, 1 RPMB and 4 GPs. Change MMC_NUM_PHY_PARTITION from 6 to 7, which is the correct value. Signed-off-by: Yi Sun <yi.y.sun@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.Jaehoon Chung2014-08-11
| | | | | | | | | | | | | Slot quirks "disable-wp" is deprecated. Instead, use the host quirk "disable-wp". (Because the slot-node is removed in dt-file.) Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Sachin Kamat <sachin.kamat@samsung.com> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci: Use mmc core regulator infrastuctureTim Kryger2014-07-09
| | | | | | | | | | | | | | | | Switch the common SDHCI code over to use mmc_host's regulator pointers and remove the ones in the sdhci_host structure. Additionally, use the common mmc_regulator_get_supply function to get the regulators and set the ocr_avail mask. This change sets the ocr_avail directly based upon the voltage ranges supported which ensures ocr_avail is set correctly while allowing the use of regulators that can't provide exactly 1.8v, 3.0v, or 3.3v. Signed-off-by: Tim Kryger <tim.kryger@gmail.com> Signed-off-by: Markus Mayer <markus.mayer@linaro.org> Reviewed-by: Matt Porter <mporter@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci: track whether preset mode is currently enabled in hardwareRussell King2014-05-22
| | | | | | | | | | | | Track whether preset mode is currently enabled in hardware, and use that when making decisions elsewhere in the code rather than reading the register and checking the bit. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: sdhci: cache timing information locallyRussell King2014-05-22
| | | | | | | | | | | | | | Rather than reading back the timing information from the registers, cache it locally. This allows implementations to translate the UHS timing by overriding the set_uhs_signaling() method as required without also having to emulate the SDHCI_HOST_CONTROL2 register. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> [Ulf Hansson] Resolved conflict Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: sdhci: convert sdhci_set_clock() into a library functionRussell King2014-05-22
| | | | | | | | Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: sdhci: move FSL ESDHC reset handling quirk into esdhc codeRussell King2014-05-22
| | | | | | | | | | | | The Freescale esdhc driver is the only driver which needs the interrupt registers restored after a reset. Move this quirk to be part of the ESDHC driver implementation. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: sdhci: more efficient interrupt enable register handlingRussell King2014-05-22
| | | | | | | | | | | Rather than wasting cycles read-modify-writing the interrupt enable registers, cache the value locally instead. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: sdhci: push card_tasklet into threaded irq handlerRussell King2014-05-22
| | | | | | | | | | | | There's no requirement to have the card tasklet separate now that we have a threaded interrupt handler, so kill this and move the called code into the threaded part of the handler. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: sdhci: convert to new SDIO IRQ handlingRussell King2014-05-22
| | | | | | | | | | | | | | | | | | Use a generic threaded interrupt handler for SDIO interrupt handling, rather than allowing the SDIO core code to buggily spawn its own thread. This results in host drivers to be more in control of how SDIO interrupts are acknowledged in the hardware, rather than having the internals of the SDIO core placed upon them, possibly resulting in sub-standard handling. At least one SDHCI implementation specifies a very specific sequence to deal with a card interrupt. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: sdio_irq: rework sdio irq handlingRussell King2014-05-22
| | | | | | | | | | | | | | | | | | Rather than the SDIO support spawning it's own thread for handling card interrupts, use the generic IRQ infrastructure for this, triggering it from the host interface's interrupt handling directly. This avoids a race between the parent thread waiting to receive an interrupt response from the card, and the slow startup from the sdio irq thread, which can occur as a result of high system load (eg, while udev is running.) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> [Ulf Hansson] Resolved conflict Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: core: Improve support for deferred regulatorsTim Kryger2014-05-12
| | | | | | | | | | | | | | | | Callers of mmc_regulator_get_supply could benefit from knowing if either of the regulators are present but not yet available. Since callers do not currently examine the return value, modify this function to return zero or -EPROBE_DEFER if either regulator get returns the same. Furthermore, since callers check vmmc/vqmmc using IS_ERR and can deal with absent regulators, switch to devm_regulator_get_optional. This has the added benefit of allowing this function to behave correctly even in the !CONFIG_REGULATOR case such that the stub can be removed. Signed-off-by: Tim Kryger <tim.kryger@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: add support for HS400 mode of eMMC5.0Seungwon Jeon2014-05-12
| | | | | | | | | | | | | | | This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high speed DDR interface timing from HS200. Clock frequency is up to 200MHz and only 8-bit bus width is supported. In addition, tuning process of HS200 is required to synchronize the command response on the CMD line because CMD input timing for HS400 mode is the same as HS200 mode. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Reviewed-by: Jackey Shen <jackey.shen@amd.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: rework selection of bus speed modeSeungwon Jeon2014-05-12
| | | | | | | | | | | | | | | | | | Current implementation for bus speed mode selection is too complicated. This patch is to simplify the codes and remove some duplicate parts. The following changes are including: * Adds functions for each mode selection(HS, HS-DDR, HS200 and etc) * Rearranged the mode selection sequence with supported device type * Adds maximum speed for HS200 mode(hs200_max_dtr) * Adds field definition for HS_TIMING of EXT_CSD Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: identify available device type to selectSeungwon Jeon2014-05-12
| | | | | | | | | | | | Device types which are supported by both host and device can be identified when EXT_CSD is read. There is no need to check host's capability anymore. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: drop the speed mode of card's stateSeungwon Jeon2014-05-12
| | | | | | | | | | | Timing mode identifier has same role and can take the place of speed mode. This change removes all related speed mode. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: dw_mmc: remove unused member variable.Jaehoon Chung2014-05-12
| | | | | | | | | | Since using the device-tree, didn't use the callback pointer. So removed the unused callback pointer. When the set_power callback is used, it should be added in future. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: card.h: Use NULL instead of 0 for END_FIXUPFabio Estevam2014-04-22
| | | | | | | | | | | | Fix the following sparse warnings: drivers/mmc/card/block.c:2421:9: warning: Using plain integer as NULL pointer drivers/mmc/core/quirks.c:69:9: warning: Using plain integer as NULL pointer Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: Delay the card_event callback into the mmc_rescan workerMarkus Mayer2014-04-22
| | | | | | | | | | | | | | This change removes the callback from atomic context which it doesn't need to be in, and puts it in line with the debounced rescan. This code is based on these e-mail threads with Christian Daudt: https://lkml.org/lkml/2013/8/19/539 https://lkml.org/lkml/2014/3/19/79 Signed-off-by: Markus Mayer <markus.mayer@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: clarify DDR timing mode between SD-UHS and eMMCSeungwon Jeon2014-04-20
| | | | | | | | | | This change distinguishes DDR timing mode of current mixed usage to clarify device type. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* Merge tag 'mmc-updates-for-3.15-rc1' of ↵Linus Torvalds2014-04-09
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc Pull MMC updates from Chris Ball: "MMC highlights for 3.15: Core: - CONFIG_MMC_UNSAFE_RESUME=y is now default behavior - DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V - Add GPIO descriptor based slot-gpio card detect API Drivers: - dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c - mmci: Support HW busy detection on ux500 - omap: Support MMC_ERASE - omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23 - rtsx: Support pre-req/post-req async - sdhci: Add support for Realtek RTS5250 controllers - sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect - sdhci-msm: Add new driver for Qualcomm SDHCI chipset support - sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs" * tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits) mmc: sdhci-acpi: Intel SDIO has broken card detect mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller mmc: sdhci-msm: Add platform_execute_tuning implementation mmc: sdhci-msm: Initial support for Qualcomm chipsets mmc: sdhci-msm: Qualcomm SDHCI binding documentation sdhci: only reprogram retuning timer when flag is set mmc: rename ARCH_BCM to ARCH_BCM_MOBILE mmc: sdhci: Allow for irq being shared mmc: sdhci-acpi: Add device id 80860F16 mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14 mmc: slot-gpio: Add GPIO descriptor based CD GPIO API mmc: slot-gpio: Split out CD IRQ request into a separate function mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform" mmc: sdhci-spear: use generic card detection gpio support mmc: sdhci-spear: remove support for power gpio mmc: sdhci-spear: simplify resource handling mmc: sdhci-spear: fix platform_data usage mmc: sdhci-spear: fix error handling paths for DT mmc: sdhci-bcm-kona: fix build errors when built-in ...
| * mmc: slot-gpio: Add GPIO descriptor based CD GPIO APIAdrian Hunter2014-03-17
| | | | | | | | | | | | | | | | | | | | | | | | Add functions to request a CD GPIO using the GPIO descriptor API. Note that the new request function is paired with mmc_gpiod_free_cd() not mmc_gpio_free_cd(). Note also that it must be called prior to mmc_add_host() otherwise the caller must also call mmc_gpiod_request_cd_irq(). Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: sdhci-spear: remove support for power gpioRussell King2014-03-04
| | | | | | | | | | | | | | | | | | | | | | None of this code is currently used: there are no definitions of struct sdhci_plat_data in arch/arm, neither are there any DT properties which use card_power_gpio/power_active_high/power_always_enb. In any case, slot power control should be rigged up via vmmc and the regulator subsystem in the DT case. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: core: Add ignore_crc flag to __mmc_switchUlf Hansson2014-02-23
| | | | | | | | | | | | | | | | | | Instead of handle specific adaptations, releated to certain switch operations, inside __mmc_switch, push this to be handled by the caller instead. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: core: Rename cmd_timeout_ms to busy_timeoutUlf Hansson2014-02-23
| | | | | | | | | | | | | | | | To better reflect that the cmd_timeout_ms is directly related to the busy detection timeout, let's rename it. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: core: Rename max_discard_to to max_busy_timeoutUlf Hansson2014-02-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rename host->max_discard_to to host->max_busy_timeout, to reflect that it tells the mmc core layer about the maximum supported busy detection timeout by the host. This timeout is at the moment only applicable to erase/trim/discard commands. By the renaming we provide the option of make use of it for other commands that cares about busy detection. In other words, those commands that wants an R1B response, like for example the mmc switch command. Do note that the max_busy_timeout is supposed to be specified only by hosts supporting MMC_CAP_WAIT_WHILE_BUSY. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: sdhci: add support for realtek rts5250Micky Ching2014-02-22
| | | | | | | | | | | | | | | | Add support for realtek rts5250 pci card reader. The card reader has some problems with DDR50 mode, so add a new quirks2 for broken ddr50. Signed-off-by: Micky Ching <micky_ching@realsil.com.cn> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: core: Enable MMC_CAP2_CACHE_CTRL as defaultUlf Hansson2014-02-13
| | | | | | | | | | | | | | | | | | | | There are no reason to why the use of a non-volatile internal eMMC cache should be controlled by a host cap. Instead let's just enable it if the eMMC card supports it. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: core: Use mmc_flush_cache() during mmc suspendUlf Hansson2014-02-13
| | | | | | | | | | | | | | | | | | | | | | | | | | Earlier we disabled the cache during suspend, which meant a flush was internally at the eMMC performed as well. To simplify code we can make use of the mmc_flush_cache(), during mmc suspend, which makes the mmc_cache_ctrl() redundant so then we can remove it. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: core: Remove support for MMC_CAP2_NO_SLEEP_CMDUlf Hansson2014-02-13
| | | | | | | | | | | | | | | | | | There are no active users of this host capability. The primary reason for adding this cap was due to a bug in ux500 boot loader code, which is not a relevant issue any more. So, let's remove it. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: core: Remove unused host cap MMC_CAP2_BROKEN_VOLTAGEUlf Hansson2014-02-13
| | | | | | | | | | Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: card: Remove host cap MMC_CAP2_SANITIZEUlf Hansson2014-02-13
| | | | | | | | | | | | | | | | There is no need for keeping a host cap for MMC_CAP2_SANITIZE, instead we just make the feature default available. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: core: Use MMC_UNSAFE_RESUME as default behaviorUlf Hansson2014-02-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Invoking system suspend or shutdown without using the Kconfig option MMC_UNSAFE_RESUME, did trigger an ungraceful power cut of the card. To improve the situation, change the behavior to always make use of the available bus_ops callbacks that handles system suspend and shutdown properly. By changing the behavior MMC_UNSAFE_RESUME becomes redundant, so lets's remove it. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* | brcmfmac: add BCM4354 SDIO interface supportFranky Lin2014-03-17
|/ | | | | | | | | | | BCM4354 is an a/b/g/n/ac 2x2 WiFi chip. This patch adds support for it through SDIO interface. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge tag 'mmc-updates-for-3.14-rc1' of ↵Linus Torvalds2014-01-26
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc Pull MMC updates from Chris Ball: "MMC highlights for 3.14: Core: - Avoid get_cd() on cards marked nonremovable Drivers: - arasan: New driver for controllers found in e.g. Xilinx Zynq SoC - dwmmc: Support Hisilicon K3 SoC controllers - esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM - sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540 - tegra: Support Tegra124 SoCs" * tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (55 commits) mmc: sdhci-pci: Fix possibility of chip->fixes being null mmc: sdhci-pci: Fix BYT sd card getting stuck in runtime suspend mmc: sdhci: Allow for long command timeouts mmc: sdio: add a quirk for broken SDIO_CCCR_INTx polling mmc: sdhci: fix lockdep error in tuning routine mmc: dw_mmc: k3: remove clk_table mmc: dw_mmc: fix dw_mci_get_cd mmc: dw_mmc: fix sparse non static symbol warning mmc: sdhci-esdhc-imx: fix warning during module remove function mmc: sdhci-esdhc-imx: fix access hardirq-unsafe lock in atomic context mmc: core: sd: implement proper support for sd3.0 au sizes mmc: atmel-mci: add vmmc-supply support mmc: sdhci-pci: add broken HS200 quirk for Intel Merrifield mmc: sdhci: add quirk for broken HS200 support mmc: arasan: Add driver for Arasan SDHCI mmc: dw_mmc: add dw_mmc-k3 for k3 platform mmc: dw_mmc: use slot-gpio to handle cd pin mmc: sdhci-pci: add support of O2Micro/BayHubTech SD hosts mmc: sdhci-pci: break out definitions to header file mmc: tmio: fixup compile error ... Conflicts: MAINTAINERS
| * mmc: sdio: add a quirk for broken SDIO_CCCR_INTx pollingBing Zhao2014-01-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Polling SDIO_CCCR_INTx could create a fake interrupt with Marvell SD8797 card. Add a quirk to handle this case. The fixup here is to issue a dummy CMD52 read to function 0 register 0xff, and this dummy read must be right after SDIO_CCCR_INTx is read. Patch has been verified on a dw_mmc controller (Samsung Chromebook) with MMC_CAP_SDIO_IRQ disabled. Signed-off-by: Bing Zhao <bzhao@marvell.com> Reviewed-by: Paul Stewart <pstew@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: sdhci: add quirk for broken HS200 supportDavid Cohen2014-01-13
| | | | | | | | | | | | | | | | | | | | This patch defines a quirk for platforms unable to enable HS200 support. Signed-off-by: David Cohen <david.a.cohen@linux.intel.com> Reviewed-by: Chuanxiao Dong <chuanxiao.dong@intel.com> Acked-by: Dong Aisheng <b29396@freescale.com> Cc: stable <stable@vger.kernel.org> # [3.13] Signed-off-by: Chris Ball <chris@printf.net>
| * mmc: SDHI: add SoC specific workaround via HW versionKuninori Morimoto2014-01-13
| | | | | | | | | | | | | | | | | | | | One of Renesas SDHI chip needs workaround to use it, and, we can judge it based on chip version. This patch adds very quick-hack workaround method, since we still don't know how many chips need workaround in the future. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Chris Ball <cjb@laptop.org>
generated by cgit v1.2.2 (git 2.25.0) at 2024-11-13 01:52:24 -0500