aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAge
* [WATCHDOG] pcwd_pci.c control status + boot-code clean-upWim Van Sebroeck2005-09-29
| | | | | | | | * Clean-up control status code (use control status defines + change pcipcwd_clear_status) * Clean-up boot-code (move card info to pcipcwd_show_card_info() ) Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* Merge branch 'for-linus' from ↵Linus Torvalds2005-09-28
|\ | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
| * [IB] mthca: fix hw_ver value returned from mthca_query_deviceJack Morgenstein2005-09-27
| | | | | | | | | | | | | | The IB spec defines the field to be 32 bits, not 16 bits. Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * [IB] mthca: Round up number of slots in HCA context memory tableMichael S. Tsirkin2005-09-27
| | | | | | | | | | | | | | | | | | | | When allocating a table for mem-free HCA context, don't assume that obj_size * nobj is an even multiple of MTHCA_TABLE_CHUNK_SIZE. In particular, make sure we allocate at least one slot even if the table is smaller than MTHCA_TABLE_CHUNK_SIZE. Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * [IB] uverbs: Close some exploitable racesRoland Dreier2005-09-26
| | | | | | | | | | | | | | | | | | | | | | | | | | Al Viro pointed out that the current IB userspace verbs interface allows userspace to cause mischief by closing file descriptors before we're ready, or issuing the same command twice at the same time. This patch closes those races, and fixes other obvious problems such as a module reference leak. Some other interface bogosities will require an ABI change to fix properly, so I'm deferring those fixes until 2.6.15. Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * [IB] mthca: Fix off by one bug in mthca_map_cmdMichael S. Tsirkin2005-09-26
| | | | | | | | | | | | | | | | The loop in mthca_map_cmd() would fill one entry past the end of the mailbox buffer before calling the firmware command. Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * [IB] mthca: fix off by one in clr_int calculationMichael S. Tsirkin2005-09-26
| | | | | | | | | | | | | | | | We should use the first word of the clear interrupt register if the bit we're after is < 32, not < 31. Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * [IB] mthca: Fix doorbell record resource leakRoland Dreier2005-09-26
| | | | | | | | | | | | | | | | | | | | | | If we allocate a bunch of doorbell records and then free them, we'll end up with completely empty pages, which we then free. However, when we come back to allocate more doorbell pages, we have to reallocate those empty pages rather than always trying to take a slot that we've never used. If we don't, we eventually use up every slot and fail to allocate a doorbell record, even though we have plenty of free space. Signed-off-by: Roland Dreier <rolandd@cisco.com>
* | [PATCH] device-mapper: Fix queue_if_no_path initialisationAlasdair G Kergon2005-09-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When creating a multipath device, if the queue_if_no_path parameter is specified it gets ignored. While the queue_if_no_path variable is correctly set to 1, the saved_queue_if_no_path gets set to 0. When the device is subsequently made live (resumed), the saved value (0) always overwrites the live value (1) so the option *always* gets turned off. The fix adds a parameter to the queue_if_no_path() function to indicate whether the previous value should be preserved or not - if not, as when the device is being set up, the saved value is set to the new value (1). Signed-Off-By: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | [PATCH] device-mapper: Trigger an event when a table is deletedgoggin, edward2005-09-28
| | | | | | | | | | | | | | | | | | | | | | If anything is waiting on a device's table when the device is removed, we must first wake it up so it will release its reference. Otherwise the table's reference count will not drop to zero and the table will not get removed. Signed-Off-By: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | [PATCH] orinoco: Fix flood of kernel log with stupid WE warningsBenjamin Herrenschmidt2005-09-28
| | | | | | | | | | | | | | | | | | | | | | Latest wireless extensions moved a field from netdev -> wireless_handlers. The WE core will now printk a warning on every call to get_wireless_stats() on a driver that still uses the old field. This patch fixes orinoco. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | [PATCH] Add IPMI poweroff control to sysfsCorey Minyard2005-09-28
| | | | | | | | | | | | | | | | | | Put the IPMI poweroff_powercycle parameter into sysfs. This field is dynamically settable and is valuable to have in sysfs. Signed-off-by: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | [PATCH] dvb: fix NULL pointer dereference when loading the budget-av moduleJon Burgess2005-09-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ralph Metzler wrote: > AFAIR, there is a bug in tda10021.c in tda10021_readreg() which > references state->frontend.dvb->num > This is fatal if the frontend is not at the probed address and thus > not yet registered (no dvb entry set yet -> NULL pointer ...). The attached patch should get rid of the oops. Signed-off-by: Jon Burgess <jburgess@uklinux.net> Cc: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds2005-09-27
|\ \
| * | [TG3]: Update driver version and release date.David S. Miller2005-09-27
| | | | | | | | | | | | Signed-off-by: David S. Miller <davem@davemloft.net>
| * | [TG3]: misc. fixesMichael Chan2005-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix interrupt test handler by adding check for IRQ assertion in PCI_STATE register in addition to the status block updated bit. Add test for valid ethernet address in tg3_set_mac_addr(). Add tg3_bus_string() to setup the PCI bus speed/width string for all PCI/PCIX/PCI Express devices. This is used to print the bus type during init_one(). Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | [TG3]: 5780 PHY fixesMichael Chan2005-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix 5780 PHY related problems: 1. MAC_RX_MODE reset must be done before setting up the MAC_MODE register on 5705_PLUS chips or the chip will stop receiving after a while. The MAC_RX_MODE reset is needed to prevent intermittently losing the first receive packet on serdes chips. 2. Skip MAC loopback test on 5780 because of hardware errata. Normal traffic including PHY loopback is not affected by the errata. 3. PHY loopback fails intermittently on 5708S and this is fixed by putting the PHY in loopback mode first before programming the MAC mode register. A MAC_RX_MODE reset is also added. 4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow nway_reset if 5780S is in parallel detect mode. 5. Add missing PHY IDs in KNOWN_PHY_ID() macro. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds2005-09-26
|\| |
| * | [CONNECTOR]: async connector mode.Evgeniy Polyakov2005-09-26
| |/ | | | | | | | | | | | | | | | | | | | | | | If input message rate from userspace is too high, do not drop them, but try to deliver using work queue allocation. Failing there is some kind of congestion control. It also removes warn_on on this condition, which scares people. Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge master.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6Linus Torvalds2005-09-26
|\ \
| * | [PATCH] pcmcia: update ID for NinjaATADominik Brodowski2005-09-26
| | | | | | | | | | | | | | | | | | | | | | | | Christian Zoz reported there are multiple NinjaATA devices all sharing the second product ID string, but not the first one. Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
| * | [PATCH] yenta: more ENE bridgesDaniel Ritz2005-09-26
| | | | | | | | | | | | | | | | | | | | | | | | Adds better support for the CB-710, CB-712, CB-720 and CB-722 bridges from EnE Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
| * | [PATCH] pcmcia: new IDs for serial_csDominik Brodowski2005-09-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add new ID to serial_cs.c; the CIS fimware override is available by the manufacturer at http://www.sierrawireless.com . Remember to name the CIS binary SW_7xx_SER.cis and to put it into /lib/firmware/ Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
| * | [PATCH] yenta: add support for more TI bridgesDaniel Ritz2005-09-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Support some more TI cardbus bridges. most of them are multifunction devices which adds 1394 controllers, smartcard readers etc. this could also help with the various problems with the XX21 controllers seen on the linux-pcmcia list. Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
| * | [PATCH] pcmcia: fix Kconfig dependencyKomuro2005-09-26
| | | | | | | | | | | | | | | | | | | | | | | | TCIC depends on ISA. It is used with ISA-bus system only. Signed-off-by: komurojun-mbn@nifty.com Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
| * | [PATCH] yenta: tiny cleanupDominik Brodowski2005-09-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | pci_set_power_state is not needed, as we call pci_enable_device() somewhere else. Also, the resource we write to PCI_BASE_ADDRESS_0 needs to be converted to bus-centric view first. Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
| * | [PATCH] yenta: don't mess with bridge control registerDaniel Ritz2005-09-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In interrupt probing (both ISA and PCI) the bridge control register is used to change interrupt routing to ISA or PCI by changing bit 7. But this bit only controls the routing of card functional interrupts, not the CSC interrupts which are used for interrupt probing. A bad side effect of messing with this register in yenta_probe_irq() is that it can lead to irq storms if a card is inserted and already powered by the BIOS. Usage in yenta_sock_init() and yenta_config_init() seem to be fishy as well. Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
| * | [PATCH] yenta: auto-tune EnE bridges for CardBus cardsDaniel Ritz2005-09-26
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Echo Audio cardbus products are known to be incompatible with EnE bridges. in order to maybe solve the problem a EnE specific test bit has to be set, another cleared...but other setups have a good chance to break when just forcing the bits. so do the whole thingy automatically. The patch adds a hook in cb_alloc() that allows special tuning for the different chipsets. for ene just match the Echo products and set/clear the test bits, defaults to do the same thing as w/o the patch to not break working setups. Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Cc: Linus Torvalds <torvalds@osdl.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* / [PATCH] missing asm/irq.h (cs89x0)Al Viro2005-09-26
|/ | | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Merge master.kernel.org:/home/rmk/linux-2.6-ucbLinus Torvalds2005-09-24
|\
| * [MFD] Fix "bious one-bit signed bitfield" errorsRussell King2005-09-24
| | | | | | | | | | | | | | ucb1x00-ts declared a couple of one-bit 'int' bitfields. Make them unsigned. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | Merge master.kernel.org:/home/rmk/linux-2.6-serialLinus Torvalds2005-09-24
|\ \
| * | [SERIAL] Remove unused variable in clps711x.cRussell King2005-09-24
| |/ | | | | | | Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* / [PATCH] Input: check switch bitmap when matching handlersDmitry Torokhov2005-09-24
|/ | | | | | | | The wwitch bitmap was added to input_device_id structure and we should check it when matching handlers and input devices. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Merge branch 'upstream' from ↵Linus Torvalds2005-09-23
|\ | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
| * Merge /spare/repo/linux-2.6/Jeff Garzik2005-09-23
| |\
| * | [PATCH] Add NVIDIA device ID in sata_nvAndy Currid2005-09-21
| | | | | | | | | | | | | | | Signed-off-by: Andy Currid <acurrid@nvidia.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
| * | [PATCH] PATCH: remove function for non-PCI as requestedAlan Cox2005-09-16
| | | | | | | | | | | | | | | Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
| * | [PATCH] PATCH: silly in piix driverAlan Cox2005-09-16
| | | | | | | | | | | | | | | Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* | | Merge branch 'upstream-fixes' from ↵Linus Torvalds2005-09-23
|\ \ \ | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
| * | | [PATCH] skge: fix Yukon-Lite A0 workaroundStephen Hemminger2005-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is one of those workarounds sucked over from sk98lin driver. The skge driver needs to detect the Yukon-Lite A0 chip properly, and turn of Rx FIFO Flush. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
| * | | [PATCH] 8390 Tx fix for non i386 machinesPaul Gortmaker2005-09-23
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | While this is true, E8390_CMD is zero on i386, and thus there should be no effect for these machines. Machines like Mac, Amiga etc. which use Alan's clever register mapping may have a non-zero E8390_CMD and result in bogus "transmitter busy" type messages from this bug. Fixes BUG# 3991.
* | | [PATCH] ipmi_msghandler: inconsistent spin_lock usageHironobu Ishii2005-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | I found an inconsistent spin_lock usage in ipmi_smi_msg_received. Signed-off-by: Hironobu Ishii <hishii@soft.fujitsu.com> Cc: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | | [PATCH] atyfb c99 fixAndrew Morton2005-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - fix this: drivers/video/aty/xlinit.c: In function `atyfb_xl_init': drivers/video/aty/xlinit.c:256: warning: ISO C90 forbids mixed declarations and code - repair some kooky coding style - Use ARRAY_SIZE() Cc: Tom 'spot' Callaway <tcallawa@redhat.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | | [PATCH] hisax: remove URB_ASYNC_UNLINKKarsten Keil2005-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | usb_unlink_urb is always async now, so URB_ASYNC_UNLINK was removed from core USB and we must do as well. Signed-off-by: Karsten Keil <kkeil@suse.de> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | | [PATCH] pci: fixup parent subordinate busnrIvan Kokshaysky2005-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I believe the change that broke things is introduction of pci_fixup_parent_subordinate_busnr(). The patch here does two things: - hunk #1 should fix the problems you've seen when you boot without additional "pci" kernel options; - hunk #2 supposedly fixes boot with "pci=assign-busses" option which otherwise hangs Acer TM81xx machines as reported. Please try this with and without "pci=assign-busses". If it boots, I'd like to see 'lspci -vvx' for both cases. Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | | [PATCH] mesh scsi: fix error handlingBenjamin Herrenschmidt2005-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The PowerMac mesh SCSI driver had some missing error handling which would trigger warnings due to lack of handling of return value from scsi_add_host. This fixes it. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | | [PATCH] ppc64: SMU driver update & i2c supportBenjamin Herrenschmidt2005-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SMU is the "system controller" chip used by Apple recent G5 machines including the iMac G5. It drives things like fans, i2c busses, real time clock, etc... The current kernel contains a very crude driver that doesn't do much more than reading the real time clock synchronously. This is a completely rewritten driver that provides interrupt based command queuing, a userland interface, and an i2c/smbus driver for accessing the devices hanging off the SMU i2c busses like temperature sensors. This driver is a basic block for upcoming work on thermal control for those machines, among others. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | | [PATCH] hdaps: small update.Robert Love2005-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Handle dmi_system_check() elegantly, now that my bugfix is upstream. - Add support for the X41 and R52. - Cleanup some comments do I do not have to keep updating them with each new whitelisted laptop. Signed-off-by: Robert Love <rml@novell.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | | [PATCH] Fix mmap() of /dev/hpetKeir Fraser2005-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The address passed to io_remap_pfn_range() in hpet_mmap() does not need to be converted using __pa(): it is already a physical address. This bug was found and the patch suggested by Clay Harris. I introduced this particular bug when making io_remap_pfn_range changes a few months ago. In fact mmap()ing /dev/hpet has *never* previously worked: before my changes __pa() was being executed on an ioremap()ed virtual address, which is also invalid. Signed-off-by: Keir Fraser <keir@xensource.com> Cc: Robert Picco <Robert.Picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
generated by cgit v1.2.2 (git 2.25.0) at 2024-11-18 01:30:50 -0500