aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAge
* [PATCH] IDE core: driver layer error checkingRandy Dunlap2006-10-03
| | | | | | | | Check driver layer return values in IDE core. Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] ide: backport piix fixes from libata into the legacy driverAlan Cox2006-10-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are three flags being set by default by the PIIX driver for speeds > PIO 1, and one not being cleared properly on fallback to PIO0. The most important one is the prefetch/post write control which only works for ATA and can do bad things with ATAPI. The patch does its best to set the flags correctly for drivers/ide. Its not 100% perfect but its closer than the original. 100% perfect requires proper IORDY handling but this isn't critical (and its not right in libata either .. yet) Sergei Shtylyov <sshtylyov@ru.mvista.com> said: > + { 0, 0 }, > + { 0, 0 }, > + { 1, 0 }, > + { 2, 1 }, > + { 2, 3 }, }; > > pio = ide_get_best_pio_mode(drive, pio, 5, NULL); BTW, there's quite obvious error here which leads to access outside of timings[] if somebody passes PIO mode 5 (or autotuning code finds out that drive supports PIO mode 5). Could have been fixed while at it... Those drives should be rare, though... > + } > master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8); > } > pci_write_config_word(dev, master_port, master_data); Actually, there's one more serious issue with piix_tune_drive() -- it doesn't actually set the drive's own transfer mode. Signed-off-by: Alan Cox <alan@redhat.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] ide: fix revision comparison in ide_in_drive_listKirill Smelkov2006-10-03
| | | | | | | | | | | Fix ide_in_drive_list: drive_table->id_firmware should be searched *in* id->fw_rev, not vice versa. Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Enable cdrom dma access with pdc20265_oldTobias Oed2006-10-03
| | | | | | | | | | | | | | | | | | | | This patch allows me to use dma with my cd/dvd attached to my on board pdc20265 ide controller Alan sayeth: Looks sane. Would be nice to know if there is any documentation supporting this hack being safe but the logic makes sense. The LBA48 case faces the same problem - the state machine gets confused about the transfer length and needs kicking Signed-off-by: Tobias Oed <tobiasoed@hotmail.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Jens Axboe <axboe@suse.de> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] ide_dma_speed() fixesSergei Shtylyov2006-10-03
| | | | | | | | | | | | | | ide_dma_speed() fails to actually honor the IDE drivers' mode support masks) because of the bogus checks -- thus, selecting the DMA transfer mode that the driver explicitly refuses to support is possible. Additionally, there is no check for validity of the UltraDMA mode data in the drive ID, and the function is misdocumented. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Make number of IDE interfaces configurableMatt Mackall2006-10-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make IDE_HWIFS configurable if EMBEDDED This lets us lop as much as 16k off an x86 build. It's a little ugly, but it's dead simple. Note the fix for HWIFS < 2. Sizing interfaces dynamically unfortunately turns out to be pretty major surgery. add/remove: 0/1 grow/shrink: 0/11 up/down: 0/-16182 (-16182) function old new delta ide_hwifs 16920 1692 -15228 init_irq 1113 750 -363 ideprobe_init 283 138 -145 ide_pci_setup_ports 1329 1193 -136 save_match 85 - -85 ide_register_hw_with_fixup 367 287 -80 ide_setup 1364 1308 -56 is_chipset_set 40 4 -36 create_proc_ide_interfaces 225 205 -20 init_ide_data 84 67 -17 ide_probe_for_cmd640x 1198 1183 -15 ide_unregister 1452 1451 -1 Signed-off-by: Matt Mackall <mpm@selenic.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] IDE error handling fixesHua Zhong2006-10-03
| | | | | | | | | | | | | | | | | | | | | In 2.6.15.1 I encountered some IDE crashes when unplugging IDE cables to emulate disk errors. Below is a patch against 2.6.16 which I think still applies. 1. The first BUG_ON could trigger when a PREFLUSH IO fails (it would fail the original barrier request which hasn't been marked REQ_STARTED yet). 2. the rq could have been dequeued already (same as 1). 3. HWGROUP(drive)->rq could be NULL because of the ide_error() several lines earlier. Signed-off-by: Hua Zhong <hzhong@gmail.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] IDE: always release DMA engineSergei Shtylylov2006-10-03
| | | | | | | | | | | | | Release the DMA engine for the custom mapping IDE drivers also (for example, siimage.c does allocate it in both I/O-mapped and custom-mapped modes). Remove useless code from the error path of ide_allocate_dma_engine(). Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] IDE: claim extra DMA ports regardless of channelSergei Shtylylov2006-10-03
| | | | | | | | | | | | | | - Claim extra DMA I/O ports regardless of what IDE channels are present/enabled. - Remove extra ports handling from ide_mapped_mmio_dma() since it's not applicable to the custom-mapping IDE drivers. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] non-libata driver for Jmicron devicesAlan Cox2006-10-03
| | | | | | | | | | | | Less functional than libata this just uses the merged interface provided for dumb legacy OS's. This is basically a bridge for people not yet ready to use libata for some reason or another. Port visibility is entirely dependant on the BIOS setup. Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] pata_hpt366: fix typoOGAWA Hirofumi2006-10-03
| | | | | | | | | | | | | | | | | | | | | switch(reg1 & 0x700) { case 5: info_hpt366.private_data = &hpt366_40; break; case 9: info_hpt366.private_data = &hpt366_25; break; default: info_hpt366.private_data = &hpt366_33; break; } The above runs always default part. It should be "(reg1 & 0x700) >> 8". Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] IPMI: allow user to override the kernel IPMI daemon enableCorey Minyard2006-10-03
| | | | | | | | | | | | | | | After the previous patch to disable the kernel IPMI daemon if interrupts were available, the issue of broken hardware was raised, and a reasonable request to add an override was mode. So here it is. Allow the user to force the kernel ipmi daemon on or off. This way, hardware with broken interrupts or users that are not concerned with performance can turn it on or off to their liking. [akpm@osdl.org: save 4 bytes in vmlinux] Signed-off-by: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] restore parport_pc probing on powermacOlaf Hering2006-10-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The last change for partport_pc did fix the common case for all PowerMacs, but it broke the case for PCI multiport IO cards. In fact, the config option CONFIG_PARPORT_PC_SUPERIO=y lead to a hard crash when cups probed the parport driver. It enables the winbond and smsc probing. Remove the PARPORT_BASE check again, parport_pc_find_nonpci_ports() will take care of it. All powerpc configs should have CONFIG_PARPORT_PC_SUPERIO=n, the code did not find anything on the chrp boards we tested it on. Tested on a G4/466 with a PCI card: 0001:10:13.0 Serial controller: Timedia Technology Co Ltd PCI2S550 (Dual 16550 UART) (rev 01) (prog-if 02 [16550]) Subsystem: Timedia Technology Co Ltd Unknown device 5079 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 53 Region 0: I/O ports at f2000800 [size=32] Region 2: I/O ports at f2000870 [size=8] Region 3: I/O ports at f2000860 [size=8] Signed-off-by: Olaf Hering <olaf@aepfle.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Adam Belay <ambx1@neo.rr.com> Cc: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] ISDN warning fixesAlan Cox2006-10-03
| | | | | | | | | | | | | | Clean up warnings in drivers/isdn by using long not int for the values where we pass void * and cast to integer types. The code is ok (ok passing the stuff this way isn't pretty but the code is valid). In all the cases I checked out the right thing happens anyway but this removes all the warnings. Signed-off-by: Alan Cox <alan@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] drivers/char/ip2: kill unused code, labelJeff Garzik2006-10-03
| | | | | | | | | | | | | | | | Kill warning: drivers/char/ip2/ip2main.c: In function ‘ip2_loadmain’: drivers/char/ip2/ip2main.c:782: warning: label ‘out_class’ defined but not used This driver's initialization (and cleanup of errors during init) is extremely convoluted, and could stand to be transformed into the standard unwinding-goto style of error cleanup. Signed-off-by: Jeff Garzik <jeff@garzik.org> Acked-by: Michael H. Warfield <mhw@wittsend.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] ipmi: fix uninitialized data bugJeff Garzik2006-10-03
| | | | | | | | | | | | | | | | gcc issues the following warning: drivers/char/ipmi/ipmi_si_intf.c: In function ‘init_ipmi_si’: drivers/char/ipmi/ipmi_si_intf.c:1729: warning: ‘data.irq’ may be used uninitialized in this function This is indeed a bug. data.irq is completely uninitialized in some code paths. Worse than that, data from a previous decode_dmi() run can easily leak through successive calls. Signed-off-by: Jeff Garzik <jeff@garzik.org> Acked-by: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] hp100: fix conditional compilation messJeff Garzik2006-10-02
| | | | | | | | | | | The previous hp100 changeset attempted to kill warnings, but was only tested on !CONFIG_ISA platforms. The correct conditional compilation setup involves tested CONFIG_ISA rather than just MODULE. Fixes link on CONFIG_ISA platforms (i386) in current -git. Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Merge branch 'for-linus' of ↵Linus Torvalds2006-10-02
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/ehca: Tweak trace message format IB/ehca: Fix device registration IB/ipath: Fix RDMA reads RDMA/cma: Optimize error handling RDMA/cma: Eliminate unnecessary remove_list RDMA/cma: Set status correctly on route resolution error RDMA/cma: Fix device removal race RDMA/cma: Fix leak of cm_ids in case of failures
| * IB/ehca: Tweak trace message formatHoang-Nam Nguyen2006-10-02
| | | | | | | | | | | | | | Add an extra space to make things more readable. Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * IB/ehca: Fix device registrationHoang-Nam Nguyen2006-10-02
| | | | | | | | | | | | | | | | | | | | Move the call to ib_register_device() later, since a device should not be registered until it is completely read to be used. This fixes crashes that occur if an upper-layer driver such as IPoIB is loaded before the ehca module. Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * IB/ipath: Fix RDMA readsRalph Campbell2006-10-02
| | | | | | | | | | | | | | | | | | | | The PSN used to generate the request following a RDMA read was incorrect and some state booking wasn't maintained correctly. This patch fixes that. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
| * RDMA/cma: Optimize error handlingKrishna Kumar2006-10-02
| | | | | | | | | | | | | | | | | | | | Reorganize code relating to cma_get_net_info() and rdam_create_id() to optimize error case handling (no need to alloc memory/etc. as part of rdma_create_id() if input parameters are wrong). Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * RDMA/cma: Eliminate unnecessary remove_listKrishna Kumar2006-10-02
| | | | | | | | | | | | | | | | | | Eliminate remove_list by using list_del_init() instead during device removal handling. Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * RDMA/cma: Set status correctly on route resolution errorSean Hefty2006-10-02
| | | | | | | | | | | | | | | | On reporting a route error, also include the status for the error, rather than indicating a status of 0 when an error has occurred. Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * RDMA/cma: Fix device removal raceKrishna Kumar2006-10-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The race is as follows: A process : cma_process_remove() calls cma_remove_id_dev(), which sets id state to CMA_DEVICE_REMOVAL and calls wait_event(dev_remove). B process : cma_req_handler() had incremented dev_remove, and calls cma_acquire_ib_dev() and on failure calls cma_release_remove(), which does a wake_up of cma_process_remove(). Then cma_req_handler() calls rdma_destroy_id(); A Process : cma_remove_id_dev() gets woken and checks the state of id, and since it is still (wrongly) CMA_DEVICE_REMOVAL, it calls notify_user(id) and if that fails, the caller - cma_process_remove() calls rdma_destroy_id(id). Two processes can call rdma_destroy_id(), resulting in one de-referencing kfreed id_priv. Fix is for process B to set CMA_DESTROYING in cma_req_handler() so that process A will return instead of doing a rdma_destroy_id(). Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * RDMA/cma: Fix leak of cm_ids in case of failuresKrishna Kumar2006-10-02
| | | | | | | | | | | | | | | | cma_connect_ib() and cma_connect_iw() leak cm_id's in failure cases. Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
* | [WATCHDOG] improve machzwd detectionDave Jones2006-10-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On a machine with no machzwd, loading the module prints out.. machzwd: MachZ ZF-Logic Watchdog driver initializing. 0xffff machzwd: Watchdog using action = RESET - the 0xffff printk is unnecessary - 0xffff seems to be 'hardware not present' - fix CodingStyle. (This driver could use some more work here) Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@osdl.org>
* | [WATCHDOG] use ENOTTY instead of ENOIOCTLCMD in ioctl()Samuel Tardieu2006-10-02
| | | | | | | | | | | | | | | | | | | | | | | | | | Return ENOTTY instead of ENOIOCTLCMD in user-visible ioctl() results The watchdog drivers used to return ENOIOCTLCMD for bad ioctl() commands. ENOIOCTLCMD should not be visible by the user, so use ENOTTY instead. Signed-off-by: Samuel Tardieu <sam@rfc1149.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org>
* | [WATCHDOG] s3c24XX nowayoutBen Dooks2006-10-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | If the driver is not configured for `no way out`, then the open method should not automatically allow the setting of allow_close to CLOSE_STATE_ALLOW. The setting of allow_close nullifies the use of the magic close via the write path. It means that in the default state, the watchdog will shut-down even if the magic close has not been issued. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* | [WATCHDOG] pnx4008: add cpu_relax()Vitaly Wool2006-10-02
| | | | | | | | | | | | | | | | Added cpu_relax as suggested by Alan Cox. Signed-off-by: Vitaly Wool <vitalywool@gmail.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* | [WATCHDOG] pnx4008_wdt.c - spinlock fixes.Wim Van Sebroeck2006-10-02
| | | | | | | | | | | | | | | | | | | | Add io spinlocks to prevent possible race conditions between start and stop operations that are issued from different child processes where the master process opened /dev/watchdog. Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* | [WATCHDOG] pnx4008_wdt.c - remove patchWim Van Sebroeck2006-10-02
| | | | | | | | | | | | | | | | | | Change remove code so that we first detach the driver from userspace, then clean up the clock and then clean up the memory we allocated. Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* | [WATCHDOG] pnx4008_wdt.c - nowayout patchWim Van Sebroeck2006-10-02
| | | | | | | | | | | | | | | | Change nowayout to: WATCHDOG_NOWAYOUT as defined in include/linux/watchdog.h . Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* | [WATCHDOG] pnx4008: add watchdog supportVitaly Wool2006-10-02
| | | | | | | | | | | | | | | | Add watchdog support for Philips PNX4008 ARM board inlined. Signed-off-by: Vitaly Wool <vitalywool@gmail.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* | [WATCHDOG] i8xx_tco remove pci_find_device.Jiri Slaby2006-10-02
| | | | | | | | | | | | | | | | | | | | Use refcounting for pci device obtaining. Use PCI_DEVICE macro. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: Andrew Morton <akpm@osdl.org>
* | [WATCHDOG] alim remove pci_find_deviceJiri Slaby2006-10-02
|/ | | | | | | | | | Convert pci_find_device to pci_get_device + pci_dev_put in alim watchdog cards' drivers (refcounting). Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@osdl.org>
* Merge branch 'upstream-linus' of ↵Linus Torvalds2006-10-02
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (37 commits) [netdrvr] hp100: encapsulate all non-module code drivers/net/wireless/{airo,ipw2100}: fix error handling bugs [netdrvr] phy: Fix bugs in error handling [PATCH] spidernet: Use pci_dma_mapping_error() [PATCH] sky2: version 1.9 [PATCH] sky2: fragmented receive for large MTU [PATCH] sky2: use netif_tx_lock instead of LLTX [PATCH] sky2: incremental transmit completion [PATCH] sky2: name irq after eth for irqbalance [PATCH] sky2: workarounds for some 88e806x chips [PATCH] sky2: use standard pci register capabilties for error register [PATCH] sky2: gigabit full duplex negotiation e100, e1000, ixgb: increment version numbers ixgb: convert to netdev_priv(netdev) ixgb: combine more rx descriptors to improve performance e1000: possible memory leak in e1000_set_ringparam e1000: Janitor: Use #defined values for literals e1000: don't strip vlan ID if 8021q claims it e1000: rework polarity, NVM, eeprom code and fixes. e1000: driver state fixes (race fix) ...
| * [netdrvr] hp100: encapsulate all non-module codeJeff Garzik2006-10-01
| | | | | | | | | | | | | | The previous '#ifndef MODULE' block did not cover all the static-build-only code. Now it does. Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * drivers/net/wireless/{airo,ipw2100}: fix error handling bugsJeff Garzik2006-10-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | airo: * fix oops, if !CONFIG_PROC_FS (create_proc_entry always returns NULL) * handle pci_register_driver() failure. if it fails, we really do want to exit, rather than (as a comment indicates) return success because-we-are-a-library. * #if 0 have_isa_dev variable, which is assigned a value but never used ipw2100: * handle sysfs_create_group() failure * handle driver_create_file() failure Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * [netdrvr] phy: Fix bugs in error handlingJeff Garzik2006-10-01
| | | | | | | | | | | | | | | | | | | | | | | | | | The recent __must_check stuff flagged some error handling bugs. phy/fixed.c: * handle device_bind_driver() failure phy/phy_device.c: * handle device_bind_driver() failure * release rwsem upon failure Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * Merge branch 'master' into upstreamJeff Garzik2006-09-30
| |\
| * \ Merge branch 'master' into upstreamJeff Garzik2006-09-27
| |\ \
| * \ \ Merge branch 'upstream' of git://lost.foo-projects.org/~ahkok/git/netdev-2.6 ↵Jeff Garzik2006-09-27
| |\ \ \ | | | | | | | | | | | | | | | into tmp
| | * | | e100, e1000, ixgb: increment version numbersAuke Kok2006-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | e100-3.5.17-k2 e1000-7.2.9-k2 ixgb-1.0.117-k2 Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
| | * | | ixgb: convert to netdev_priv(netdev)Auke Kok2006-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PCI error recovery code recently merged needs to use netdev_priv Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
| | * | | ixgb: combine more rx descriptors to improve performanceJesse Brandeburg2006-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We experimented with more descriptor buffer writebacks and found that values larger than 8 give HW problems, but 8 is safe and gives us some improved performance. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
| | * | | e1000: possible memory leak in e1000_set_ringparamVasily Averin2006-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Memory allocated for new tx_ring and rx_ring leaks if e1000_setup_XX_resources() fails.c Also this patch reduces stack usage (removed tx_new and rx_new) and uses kzalloc instead kmalloc+memset(0) Signed-off-by: Vasily Averin <vvs@sw.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
| | * | | e1000: Janitor: Use #defined values for literalsLinas Vepstas2006-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Minor janitorial patch: use #defines for literal values. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
| | * | | e1000: don't strip vlan ID if 8021q claims itBruce Allan2006-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
| | * | | e1000: rework polarity, NVM, eeprom code and fixes.Jeff Kirsher2006-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several minor issues exist in the low-level device handling code of e1000. The NVM and EEPROM writing/reading code was updated which fixes unneeded delays, adds proper eeprom aqcuiring steps and handle shadow ram and flash access. Minor cosmetic adjustments to the polarity code adding symbols. PHY reset code mistakenly distinguished between MAC types instead of PHY types, and was fixes. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-29 04:07:27 -0500